Motorola MC919Z Owner's manual

Category
Handheld mobile computers
Type
Owner's manual

This manual is also suitable for

MC919Z RFID Mobile Computer
Integrator Guide Supplement
MC919Z Integrator Guide Supplement
72E-157455-02
Rev A
March 2015
ii MC919Z Integrator Guide Supplement
© 2015 Symbol Technologies, Inc.
No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without
permission in writing from Zebra. This includes electronic or mechanical means, such as photocopying, recording, or
information storage and retrieval systems. The material in this manual is subject to change without notice.
The software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is on a
licensed basis. Zebra grants to the user a non-transferable and non-exclusive license to use each software or firmware
program delivered hereunder (licensed program). Except as noted below, such license may not be assigned,
sublicensed, or otherwise transferred by the user without prior written consent of Zebra. No right to copy a licensed
program in whole or in part is granted, except as permitted under copyright law. The user shall not modify, merge, or
incorporate any form or portion of a licensed program with other program material, create a derivative work from a
licensed program, or use a licensed program in a network without written permission from Zebra. The user agrees to
maintain Zebra’s copyright notice on the licensed programs delivered hereunder, and to include the same on any
authorized copies it makes, in whole or in part. The user agrees not to decompile, disassemble, decode, or reverse
engineer any licensed program delivered to the user or any portion thereof.
Zebra reserves the right to make changes to any software or product to improve reliability, function, or design.
Zebra does not assume any product liability arising out of, or in connection with, the application or use of any product,
circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under any Zebra Technologies
Corporation., intellectual property rights. An implied license only exists for equipment, circuits, and subsystems
contained in Zebra products.
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark
of Symbol Technologies, Inc., a Zebra Technologies company.
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
iii
Revision History
Changes to the original manual are listed below:
Change Date Description
Rev A 02/2012 Initial release.
Rev A 3/2015 Zebra Rebranding
iv MC919Z Integrator Guide Supplement
Table of Contents
Revision History............................................................................................................. iii
Table of Contents
About This Guide
Introduction.................................................................................................................... ix
Configurations................................................................................................................ ix
Chapter Descriptions..................................................................................................... x
Notational Conventions.................................................................................................. x
Related Documents and Software................................................................................. xi
Service Information........................................................................................................ xi
Chapter 1: Getting Started
Introduction ................................................................................................................... 1-1
RFID Technology Overview .......................................................................................... 1-1
RFID Components .................................................................................................. 1-2
MC919Z RFID Mobile Computer .................................................................................. 1-3
MC919Z Parts ............................................................................................................... 1-4
MC919Z LED Indicators .......................................................................................... 1-5
Reading Tags ............................................................................................................... 1-5
Chapter 2: Updating the RFID Mobile Computer
Introduction ................................................................................................................... 2-1
Updating the Device Image .......................................................................................... 2-1
Downloading an Update Loader Package .............................................................. 2-1
Updating Images via ActiveSync ............................................................................ 2-1
Updating the RFID Firmware ........................................................................................ 2-2
vi MC919Z Integrator Guide Supplement
Chapter 3: MobileRFID Functionality
Introduction ................................................................................................................... 3-1
MobileRFID Icons ......................................................................................................... 3-2
MobileRFID Menu ......................................................................................................... 3-3
Configure Region .................................................................................................... 3-4
Configure RFID ....................................................................................................... 3-7
Version Information ................................................................................................. 3-8
Run/Stop RFID ........................................................................................................ 3-9
Chapter 4: RFID Sample Application
Introduction ................................................................................................................... 4-1
Launching the RFID Sample Application ...................................................................... 4-2
Connection .................................................................................................................... 4-3
Capabilities ................................................................................................................... 4-4
Configuration Menu Options ......................................................................................... 4-5
Tag Storage Settings .............................................................................................. 4-5
Antenna ................................................................................................................... 4-6
RF Mode ................................................................................................................. 4-7
Singulation .............................................................................................................. 4-8
Power On/Off Radio ................................................................................................ 4-9
Reset to Factory Default ......................................................................................... 4-9
Operations Menu Options ............................................................................................. 4-10
Antenna Info ............................................................................................................ 4-10
Filter ........................................................................................................................ 4-11
Access .................................................................................................................... 4-14
Triggers ................................................................................................................... 4-19
Management Menu Options ......................................................................................... 4-26
Help Menu .................................................................................................................... 4-26
Exit ................................................................................................................................ 4-26
Chapter 5: Tag Locator
Introduction ................................................................................................................... 5-1
Using Tag Locator ........................................................................................................ 5-2
Locating Tags Using a .csv File .................................................................................... 5-3
Chapter 6: Troubleshooting
Introduction ................................................................................................................... 6-1
Troubleshooting ............................................................................................................ 6-1
MC919Z .................................................................................................................. 6-1
Bluetooth Connection .............................................................................................. 6-3
Four Slot Charge Only Cradle ................................................................................. 6-4
Four Slot Ethernet Cradle ....................................................................................... 6-4
Four Slot Spare Battery Charger ............................................................................ 6-6
Single Slot Serial/USB Cradle ................................................................................. 6-6
Cable Adapter Module ............................................................................................ 6-7
Magnetic Stripe Reader .......................................................................................... 6-8
Modem Module ....................................................................................................... 6-9
Table of Contents vii
Appendix A: Technical Specifications
MC919Z Specifications ................................................................................................. A-1
Decode Zones ......................................................................................................... A-5
SE960 Standard Range Laser Decode Zones ........................................................ A-5
SE1524 Long Range Laser Decode Zones ............................................................ A-7
SE4500 Standard Range Imager Decode Zones ................................................... A-9
Mobile Computer Pin-Outs ...................................................................................... A-13
Accessory Specifications .............................................................................................. A-14
Single Slot Serial/USB Cradle ................................................................................. A-14
Four Slot Ethernet Cradle ....................................................................................... A-14
Four Slot Charge Only Cradle ................................................................................. A-15
Four Slot Battery Charger ....................................................................................... A-15
Magnetic Stripe Reader .......................................................................................... A-16
Accessory CAM and MSR Pin-Outs ....................................................................... A-17
Appendix B: RFID APIs
Index
viii MC919Z Integrator Guide Supplement
About This Guide
Introduction
This MC919Z RFID Integrator Guide Supplement provides the unique set up and operating procedures for the
MC919Z RFID mobile computers. This guide is intended as a supplement to the MC9190-G Integrator Guide, p/n
72E-140937-xx. Procedures common to MC9100 products are addressed in the MC9190-G Integrator Guide.
Configurations
This guide covers the following configurations:
NOTE Screens and windows pictured in this guide are samples and can differ from actual screens.
Configuration
RFID
Frequency
Band Support
Description
MC919Z-GA0SWEQZ1WR US RFID, 1D, CLR, 256/1G, 53, WM6.5
MC919Z-GA0SWEQZ2EU EU RFID, 1D, CLR, 256/1G, 53, WM6.5
MC919Z-G30SWEQZ1WR US RFID, 2D, CLR, 256/1G, 53, WM6.5
MC919Z-G30SWEQZ2EU EU RFID, 2D, CLR, 256/1G, 53, WM6.5
MC919Z-G50SWEQZ1WR US RFID, DPM, 2D, CLR, 256/1G, 53, WM6.5
MC919Z-G50SWEQZ2EU EU RFID, DPM, 2D, CLR, 256/1G, 53, WM6.5
MC919Z-GJ0SWEQZ1WR US RFID, LRX, CLR, 256/1G, 53, WM6.5
MC919Z-GJ0SWEQZ2EU EU RFID, LRX, CLR, 256/1G, 53, WM6.5
x MC919Z Integrator Guide Supplement
Chapter Descriptions
Topics covered in this guide are as follows:
Chapter 1, Getting Started provides an overview of RFID technology and components, and a description of
the MC919Z RFID mobile computer and features.
Chapter 2, Updating the RFID Mobile Computer describes how to update the device image and radio
firmware.
Chapter 3, MobileRFID Functionality includes information on configuring the RFID radio and reading tags.
Chapter 4, RFID Sample Application provides information on the RFID sample application and how to use it
to assist in custom application development.
Chapter 5, Tag Locator provides information on the application used to detect the location of a tag.
Chapter 6, Troubleshooting describes MC919Z RFID mobile computer troubleshooting procedures.
Appendix A, Technical Specifications includes the technical specifications for the reader.
Appendix B, RFID APIs provides a reference for information on supported RFID APIs.
Notational Conventions
The following conventions are used in this document:
“Mobile computer” refers to the MC919Z hand-held computer.
Italics are used to highlight the following:
Chapters and sections in this guide
Related documents
Bold text is used to highlight the following:
Dialog box, window and screen names
Drop-down list and list box names
Check box and radio button names
Icons on a screen
Key names on a keypad
Button names on a screen.
Bullets (•) indicate:
Action items
Lists of alternatives
Lists of required steps that are not necessarily sequential.
Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists.
About This Guide xi
Related Documents and Software
The following documents provide more information about the MC919Z.
MC919Z Quick Start Guide, p/n 72-152191-xx
MC919Z Regulatory Guide, p/n 72-157453-xx
MC9190-G User Guide, p/n 72E-140936-xx
MC9190-G Integrator Guide, p/n 72E-140937-xx
Enterprise Mobility Developer Kits, available at: http://www.zebra.com/support.
Microsoft Sync software, available at: http://www.microsoft.com.
For the latest version of this guide and all guides, go to: http://www.zebra.com/support.
Service Information
If you have a problem with your equipment, contact Zebra for your region. Contact information is available at:
http://www.zebra.com/support.
When contacting Zebra support, please have the following information available:
Serial number of the unit
Model number or product name
Software type and version number
Zebra responds to calls by e-mail, telephone or fax within the time limits set forth in service agreements.
If your problem cannot be solved by Zebra support, you may need to return your equipment for servicing and will
be given specific directions. Zebra is not responsible for any damages incurred during shipment if the approved
shipping container is not used. Shipping the units improperly can possibly void the warranty.
If you purchased your business product from a Zebra business partner, please contact that business partner for
support.
xii MC919Z Integrator Guide Supplement
Chapter 1 Getting Started
Introduction
This chapter provides an overview of RFID technology and components, and describes the MC919Z RFID mobile
computer and product features.
RFID Technology Overview
RFID (Radio Frequency Identification) is an advanced automatic identification (Auto ID) technology that uses radio
frequency signals to identify tagged items. An RFID tag contains a circuit that can store data. This data may be
pre-encoded or can be encoded in the field. The tags come in a variety of shapes and sizes.
To read a tag, the mobile computer sends out radio frequency waves using its integrated antenna. This RF field
powers and charges the tags, which are tuned to receive radio waves. The tags use this power to modulate the
carrier signal. The reader interprets the modulated signal and converts the data to a format for computer storage.
The computer application translates the data into an understandable format.
Figure 1-1
RFID System Elements
Host Computer
Tags
Mobile Computer
Wireless LAN/
BT/ActiveSync
RF Wave and
Response
1 - 2 MC919Z Integrator Guide Supplement
RFID Components
Zebra RFID solutions offer low cost, long read range, and a high read rate. These features provide real time
end-to-end visibility of products and assets in the factory, distribution center, retail outlet, or other facility. The
MC919Z RFID system consists of the following components:
Silicon-based RFID tags that attach to retail products, vehicles, trailers, containers, pallets, boxes, etc.
An integrated antenna that supports applications such as item level tracking and asset tracking.
An embedded radio module that powers and communicates with tags for data capture and provides host
connectivity for data migration.
Tags
Tags contain embedded chips that store unique information. Available in various shapes and sizes, tags, often
called transponders, receive and respond to data requests. Tags require power to send data.
There are several categories of tags based on the protocol they support, read/write memory, and power options:
Active RFID tags are powered by internal light-weight batteries, and also use these batteries to broadcast
radio waves to the reader.
Semi-passive RFID tags are also powered by internal light-weight batteries, but draw broadcasting power
from the reader.
Passive RFID tags are powered by a reader-generated RF field. These tags are much lighter and less
expensive than active tags, and are typically applied to less expensive goods.
Antenna
Antennas transmit and receive radio frequency signals.
Radio Module
The radio module communicates with the tags and transfers the data to a host computer. It also provides features
such as filtering, CRC check, and tag writing. The MC919Z RFID mobile computer supports standard RFID tags as
described by EPCGlobal
TM
Class 1 Gen2 protocol.
Getting Started 1 - 3
MC919Z RFID Mobile Computer
The Zebra MC919Z RFID mobile computer includes an intelligent C1G2 UHF RFID reader with RFID read
performance that provides real-time, seamless EPC-compliant tag processing. MC919Z RFID mobile computers
are designed for back room inventory management, manufacturing floors, inside/outside loading dock and asset
tracking applications, and can host third-party, customer-driven embedded applications. Features include:
ISO 18000-6C standard (EPC Class 1 Gen 2)
Read, write, kill, lock, block write/block erase, and permalock functionality
53-key alphanumeric keypad
3.7” VGA color display
Touch panel with 340 dpi resolution
Orientation-insensitive integrated external RFID antenna
Reads 1D and 2D bar codes
Windows
®
Mobile 6.5
WLAN 802.11 a/b/g wireless connectivity
Application-specific setup for ease of installation
Low Level Reader Protocol (LLRP) - For LLRP custom extensions, refer to the Software Interface Guide p/n
72E-131718-XX.
Sample application and support for custom or third-party applications
RFID API support
Event and tag management support
Figure 1-2
MC919Z RFID Mobile Computer
1 - 4 MC919Z Integrator Guide Supplement
MC919Z Parts
Figure 1-3
MC919Z Parts
Indicator LED Bar
Power
Battery
Trigger
Microphone
Touch Screen
Scan Button
Headphone Jack
Keypad
Handstrap
Battery Release
(1 of 2)
Getting Started 1 - 5
MC919Z LED Indicators
The LEDs indicate charging and reader status as described in Table 1-1.
Reading Tags
To read RFID tags:
1. Remove the MC919Z from AC power and ensure the LLRP icon is green.
2. Use an RFID reader application to enable tag reading. For a sample application, tap on icon RFID Demo in the
start menu, or browse to the MC919Z Application directory and select CS_RFID3Sample6.exe.
See RFID Sample Application on page 4-1.
3. Aim the mobile computer at the tag, oriented horizontally or vertically depending on the tag orientation. The
distance between the tag and the antenna is the approximate read range.
Press the trigger or tap the on-screen Read command within the application to interrogate all RFID tags within the
radio frequency (RF) field of view and capture data from each new tag found. Release the trigger or tap the Stop
Read command to stop interrogating tags.
Table 1-1
MC919Z LED Status Indicators
LED Indication
Charging Indicators
Off Mobile computer not placed correctly in the cradle; cable not connected correctly;
charger not powered.
Fast Blinking Amber Error in charging; check placement of mobile computer.
Slow Blinking Amber Mobile computer is charging.
Solid Amber Charging complete.
Note: When the battery is initially inserted in the mobile computer, the amber LED
flashes once if the battery power is low or the battery is not fully inserted.
NOTE When connected to power, the mobile computer cannot read RFID tags.
1 - 6 MC919Z Integrator Guide Supplement
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96

Motorola MC919Z Owner's manual

Category
Handheld mobile computers
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI