WILSON AUDIO Watch Owner's manual

Brand: WILSON AUDIO

Model: Watch

Category: Supplementary music equipment

Type: Owner's manual

This manual is also suitable for

WATCH Controller

WILSON AUDIO Watch:

The WATCH Controller is a sophisticated audio control device designed to enhance and customize your home theater or two-channel system. With its advanced features and intuitive operation, the WATCH Controller empowers you to effortlessly optimize your listening experience and enjoy unparalleled audio performance.

Key Capabilities:

12-volt Trigger Control: Seamlessly integrate with other components in your system, such as amplifiers, subwoofers, and lighting, for automated power management.
Precision Bass Management: Fine-tune the low-frequency response of your speakers, ensuring seamless integration with your subwoofer and optimal bass performance.

WILSON AUDIO Watch:

Key Capabilities:

12-volt Trigger Control: Seamlessly integrate with other components in your system, such as amplifiers, subwoofers, and lighting, for automated power management.
Precision Bass Management: Fine-tune the low-frequency response of your speakers, ensuring seamless integration with your subwoofer and optimal bass performance.

WATCH Controller Owners Manual

WATCH Co n T r o l l e r oW n e r ’ s MA n u A l

Wilson Audio Specialties

Wilson Audio

is a registered trademark of Wilson Audio Specialties, Inc.

Cub

, Sophia

, WATT/Puppy

, MAXX

, and Alexandria

are registered trademarks of

Wilson Audio Specialties, Inc.

WilsonGloss™, Wilson Audio Duette™, WATCH

Center, WATCH

Controller, WATCH

Surround, and WATCH

Dog are trademarks of Wilson Audio Specialties, Inc.

This manual was produced by the Wilson Audio Engineering and the Sales and Mar-

keting Department. The information contained herein is subject to change without

notice. Current Revision 1.0. If you are in need of a more recent manual, please

contact your dealer.

The information in this manual is the sole property of Wilson Audio Specialties, Inc.

Any reproduction, in whole or in part, without the express written permission of

Wilson Audio Specialties, Inc., is prohibited. No material contained herein may be

transmitted in any form or by any means, electronic or mechanical, for any purpose,

without the express written permission of Wilson Audio Specialties, Inc.

Wilson Audio Specialties

SAFTEY PRECAUTIONS AND ELECTRICAL REQUIREMENTS

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT USE THIS APPLIANCE NEAR

WATER OR EXPOSE IT TO RAIN OR OTHER MOISTURE. DO NOT HANDLE THE POWER SUPPLY OR

POWER CABLES WITH WET HANDS.

CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER. NO

USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO YOUR LOCAL WILSON AUDIO DEALER ONLY.

WARNING: DO NOT PERMIT FINGERS TO TOUCH THE TERMINALS OF POWER PLUGS WHEN

INSTALLING OR REMOVING THE PLUG TO OR FROM A POWER SOURCE.

IMPORTANT SAFEGUARDS

Read instructions1. - All the safety and operating instructions should be read before operating the WATCH

Controller.

Retain instructions2. - The safety instruction and owner’s manual should be retained for future reference.

Heed Warnings3. - All warnings on the WATCH Controller and in the owner’s manual should be adhered to.

Follow Instructions4. - All operating and use instructions should be followed.

Ventilation5. – Allow adequate space for ventilation around the unit.

Cleaning6. - Unplug the WATCH Controller from the power source before cleaning and use the cloth provided by

Wilson Audio. Do not use liquid or aerosol cleaners.

Power Sources7. - This WATCH Controller should be operated only from the type of power source indicated on

the marking label.

Power Plug8. – Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has

two blades with one wider than the other. A grounding–type plug has two blades and a third grounding prong. The

wide blade or the third prong are provided for your safety. If the provided plug does not t into your outlet, consult

an electrician for replacement of the obsolete outlet.

Power-Cord Protection9. - Power-supply cords should be routed so that they are not likely to be walked on

or pinched by items placed upon or against them. Pay particular attention to cords and plugs, convenience

receptacles, and the point at which the cords exit the WATCH Controller.

Lightning or extended non-use10. - For added protection for the WATCH Controller during a lightning storm or

when the unit is not in use for an extended period of time such as a vacation, unplug its power supply from any

wall outlets. This will prevent damage to the WATCH Controller due to lightning or power line surges.

Servicing11. - Do not attempt to service this WATCH Controller yourself as opening or removing covers will expose

you to dangerous voltage and other hazards. Refer all servicing to a qualied Wilson Audio dealer.

Damage Requiring Service12. - Unplug the WATCH Controller from the power source and refer servicing to a

qualied Wilson Audio dealer under the following conditions:

If the power supply cord or plug is damaged.a.

If liquid has spilled on or objects have fallen into the WATCH Controller.b.

If the WATCH Controller has been exposed to rain or water or any amount of liquid.c.

If the WATCH Controller does not operate normally after following the operating instructions in the d.

owner’s manual.

If the WATCH Controller has been dropped or the chasse has been damaged.e.

If the WATCH Controller exhibits a distinct change in performance.f.

Replacement Parts13. - When replacement parts are required, be sure the service technician has used replacement

parts specied by Wilson Audio. Unauthorized substitutions may result in re, electric shock, or other hazards.

Safety Check14. – Upon completion of any service or repairs to this WATCH Controller, ask the service technician

to perform safety checks to determine that the product is in safe operating condition.

ENVIRONMENT

Operating Temperature: 10ºC to 40ºC (50ºF to 104ºF)

WATCH Co n T r o l l e r oW n e r ’ s MA n u A l

Wilson Audio Specialties

• WARNING: This apparatus must be connected to the AC MAINS

with a 3-prong or earth grounded plug.

• WARNING: To prevent injury, this apparatus must be securely

attached to the floor/wall in accordance with the installation

instructions.

• This apparatus should not be disposed of as household refuse.

• Do not move the apparatus by holding the power supply cord.

• If the apparatus is not in use for an extended period of time, please turn it

off and unplug it.

• Do not disconnect the apparatus with wet hands.

• This apparatus is not intended for use by children. Children should only

operate the apparatus under the direct supervision of an adult.

Wilson Audio Specialties

T A b l e o f Co n T e n T s

Contents

S e c t i o n 1 – in i t i a l Se t u p �� 9

S e c t i o n 1�1 – co n n e c t i n g t h e Watch co n t r o l l e r – ho m e

t h e a t e r �� 11

o n n e C t i o n Wi t h a Su r r o u n d Pr o C e S S o r �� 11

e c t i o n 1�2 – co n n e c t i n g t h e co n t r o l l e r – tW o –ch a n n e l

S y S t e m �� 12

o n n e C t t h e Co n t r o l l e r t o t h e Su b W o o f e r am P l i f i e r �� 12

y P a S S i n g t h e hi g h Pa S S fi l t e r �� 13

til iz in g t h e hi g h Pa S S fi l t e r �� 14

S e c t i o n 2 – Se t u p a n d Fi n a l tu n i n g �� 19

S e c t i o n 2�0 - Fr o n t pa n e l Se t u p a n d Fi n a l tu n i n g �� 21

r e P a r a t i o n �� 21

e c t i o n 2�1 - no t e S Fr o m da v i d a� Wi l S o n o n t h e te S t cd 22

u b W o o f e r Pl a C e m e n t �� 22

ilte ri ng o f lf t o t h e le f t & ri g h t SP e a k e r S �� 22

nit ia l Pl a C e m e n t o f t h e l & r SP e a k e r S �� 23

n t r o d u C t i o n o f t h e WatCh Co n t r o l l e r i n t o Sy S t e m �� 25

o eQ or no t to eQ �� 28

e c t i o n 2�2 – Br e a k - i n pe r i o d �� 30

S e c t i o n 3 – tW e l v e - v o l t tr i g g e r S �� 31

S e c t i o n 3�1 - tW e l v e - v o l t tr i g g e r co n t r o l S �� 33

S e c t i o n 4 – Sy S t e m Sp e c i F i c a t i o n S �� 37

c o n t r o l l e r Sp e c i F i c a t i o n S �� 39

o n t r o l l e r di m e n S i o n S �� 40

WATCH Co n T r o l l e r oW n e r ’ s MA n u A l

Wilson Audio Specialties

S e c t i o n 5 – Wa r r a n t y in F o r m a t i o n �� 43

S e c t i o n 5�0 – Wa r r a n t y in F o r m a t i o n �� 45

imi te d Wa r r a n t y �� 45

o n d i t i o n S �� 45

e m e d y �� 46

a r r a n t y li mi te d t o or ig ina l Pu r C h a S e r �� 46

e m o n S t r a t i o n eQ u i P m e n t �� 47

i S C e l l a n e o u S �� 47

Wilson Audio Specialties

T A b l e o f Co n T e n T s

Wilson Audio Specialties

Section 1 – Initial Setup

WATCH Co n T r o l l e r oW n e r ’ s MA n u A l

Wilson Audio Specialties

s e C T i o n 1 – in i T i A l se T u p

Section 1.1 – Connecting the WATCH Controller – Home Theater

The WATCH Controller can be connected in a variety of ways depending on your

system needs. It can be used in conjunction with a LFE (Low Frequency Effects) channel

for a dedicated home theater system, or it can be used in conjunction with a subwoofer

to extend the bass in a two-channel music system. In systems where it is desirable to

use the WATCH Controller with both the surround processor in a theater system and in

the two-channel music system via the preamp (bypassing the surround processor), you

can switch between the two sources via the WATCH Controller’s front panel’s Line/Pro-

cessor switch. This enables you to optimize the Controller for the surround mode and

music mode separately.

The WATCH Controller is also capable of accepting either balanced (XLR) or sin-

gle-ended (RCA) cable connectors from your preamplifier or surround processor. Your

choice will depend on the configuration of your particular preamp or surround proces-

sor.

Connection With a Surround Processor

Make sure the WATCH Controller power is “off” and the Level control on the front

panel is in the “Min” position during the connecting process. Locate the “Input” sec-

tion of the WATCH Controller on the rear of the unit (See Figure 1). The Processor In-

put of the WATCH Controller is designated for use with the LFE (Low Frequency Effects)

outputs of a surround processor. Balanced (XLR) or single-ended (RCA) connecting

cables may be used, depending on the connector type used on your surround processor.

Connect the LFE output of your surround processor to the WATCH Controller via the

input labeled “PROCESSOR IN.”

On the WATCH Controller front panel, locate the switch labeled “BAL/SINGLE.”

Select “BAL” for use with balanced cables or “SINGLE” for use with single-ended ca-

bles. In the same section of the front panel, locate the switch labeled “PROCESSOR,”

WATCH Co n T r o l l e r oW n e r ’ s MA n u A l

Wilson Audio Specialties

“REM,” and “LINE.” Select

the “PROCESSOR” input.

On the front panel, locate

the switch labeled “HP IN”

and “HP OUT.” Select “HP

OUT” (See Figure 3). On

the front panel, locate the

switch labeled “LP IN” and

“LP OUT.” Select “LP OUT”

(See Figure 4).

Proceed to Section 2,

“Setup and Final Tuning,” to continue the setup of your unit.

Wilson Audio has engineered very flexible high and low pass crossover filters for

the WATCH Controller. Wilson has paid particular attention to the sound quality of the

High Pass filter section. Setup and configuration of these filters is discussed in Section

2 entitled “Setup and Final Tuning.”

Section 1.2 – Connecting the Controller – Two–Channel System

Connect the Controller to the Subwoofer Amplifier

The “LOW PASS OUT” connectors labeled “1” and “2” are the output signal con-

nectors for the subwoofer amplifier (See Figure 2). The Controller sums the left and

right channels so both “1” and “2” outputs contain identical signals. There is a sin-

gle–ended and a balanced connector for each output. If you are using one subwoofer,

connect the amplifier driving the subwoofer to the Controller’s “LOW PASS OUT” via

the “1” output. Choose either the balanced cable or single–ended output to match the

input configuration of the amplifier.

Fi g u r e 1 - li n e a n d pr o c e S S o r in p u t S

Wilson Audio Specialties

If you are using two subwoofers

with separate amplifiers, connect the

second amplifier channel to the “2” out-

put. By using “Y” connectors (contact

your Wilson dealer for details), you can

connect the controller to more than two

subwoofer amplifiers.

Bypassing the High Pass Filter

In systems where the main speakers

are full-range, the subwoofer used with

the controller can be configured more

successfully without the use of the High

Pass filter. There is a normal bass roll–off that occurs naturally in your listening room.

This effect acts like a six dB per octave low pass filter and rolls off the bass from your

main speakers. In most systems it is not necessary or desirable to use the High Pass

filter. The WATCH Controller’s Low Pass filter controls in conjunction with the Bass

Equalization and Phase controls (discussed in Section 2) will allow you to successfully

integrate the main loudspeakers with the subwoofer without the use of the High Pass

filter.

Make sure the WATCH Controller power is off during the connecting process. Lo-

cate the input section of the WATCH Controller on the rear of the unit (See Figure 1).

The WATCH Controller inputs are configured for both balanced (XLR) and single-ended

(RCA) cables.

When connecting the WATCH Controller without the use of the High Pass Filter,

a second output from your preamplifier is required. If your preamplifier does not have

two sets of outputs, consult with your Wilson dealer about using high quality “Y” con-

e C T i o n 1 – in i T i A l se T u p

Fi g u r e 2 - lo W pa S S ou t p u t S

nectors to facilitate con-

necting your unit. From

one of the preamp outputs,

connect your preamp di-

rectly to your main ampli-

fier. From a second set of

preamp outputs, connect

both left and right chan-

nels to the Line Level In-

put of the WATCH Control-

ler. The WATCH Controller

automatically sums the

information from the left

and right channels when the controller is used with stereo inputs. The controller di-

rects the summed stereo channels to a single subwoofer or to multiple subwoofers used

in conjunction with the controller.

On the WATCH Controller front panel, locate the switch labeled “BAL,” and “SIN-

GLE.” Select “BAL” for use with balanced cables or “SINGLE” for use with single-ended

cables. In the same section of the front panel, locate the switch labeled “PROCESSOR,”

“REM,” and “LINE.” Select the “LINE” input. On the front panel, locate the switch label

“HP IN,” “REM,” and “HP OUT” (see Figure 3). Select “HP OUT.” On the front panel,

locate the switch labeled “LP IN,” “REM,” and “LP OUT” (See Figure 4). Select “LP

IN.”

Proceed to Section 2, “Front Panel Setup and Final Tuning,” to continue the setup

of your unit.

Utilizing the High Pass Filter

WATCH Co n T r o l l e r oW n e r ’ s MA n u A l

Wilson Audio Specialties

Fi g u r e 3 - hi g h pa S S Fi l t e r co n t r o l S

s e C T i o n 1 – in i T i A l se T u p

Wilson Audio Specialties

The WATCH Control-

ler employs a high quality

High Pass Filter as a part

of its crossover design.

The High Pass Filter can be

used to filter bass from the

main loudspeakers. This

can be desirable in systems

where the main loudspeak-

ers have limited bass dy-

namics or if the main pow-

er amplifier is low power.

Make sure the

WATCH Controller power is off during the connecting process. On the rear of the unit,

locate the Line Level inputs of the WATCH Controller. Connect the preamplifier output,

left and right, to the Line Level input of the WATCH Controller (See Figure 1). Use the

XLR inputs for balanced cables or the RCA inputs for single–ended cables.

Locate the Line High Pass Output (See Figure 5) on the rear of the Controller.

These connectors pass the high pass section of the signal to your main amplifier for

your loudspeakers. Connect the Line HP Output, left and right, of the WATCH Control-

ler to the inputs of your power amplifier. Use the XLR inputs for balanced cables or the

RCA inputs for single-ended cables.

On the WATCH Controller front panel, locate the switch labeled “BAL,” and “SIN-

GLE.” Select “BAL” for use with balanced cables, or “SINGLE” for use with single-ended

cables. In the same section of the front panel, locate the switch labeled “PROCESSOR,”

“REM,” and “LINE.” Select the “LINE” input.

Locate the switch on the front panel labeled “HP IN” and “HP OUT” (See Figure

Fi g u r e 4 - lo W pa S S Fi l t e r co n t r o l S

WATCH Co n T r o l l e r oW n e r ’ s MA n u A l

Wilson Audio Specialties

4). This switch defeats or alternatively en-

gages the high pass filter. Turn the switch

to the HP IN position.

Locate the switch on the front panel

labeled “HP 6 dB” and “HP 12 dB” (See

Figure 3). This switch changes the slope of

the high pass filter to either 6 decibels per

octave or 12 decibels per octave. The po-

sition of this switch will be set in its final

position in the final tuning stages of the

WATCH Controller. For now, set the switch

to the 6 dB per octave position.

Proceed to Section 2, “Front Panel

Setup and Final Tuning,” to continue the setup of your unit.

Note: Before proceeding with the Front Panel setup and configuration, please connect

your system as outlined in Section 2, which contains valuable information needed be-

fore proceeding further.

Fi g u r e 5 - hi g h pa S S Fi l t e r ou t p u t

Wilson Audio Specialties

s e C T i o n 1 – in i T i A l se T u p

Wilson Audio Specialties

Section 2 – Setup and Final Tuning

WATCH Co n T r o l l e r oW n e r ’ s MA n u A l

Wilson Audio Specialties

Page is loading ...

WILSON AUDIO Watch Owner's manual

Brand: WILSON AUDIO

Model: Watch

Category: Supplementary music equipment

Type: Owner's manual

This manual is also suitable for

WATCH Controller

WILSON AUDIO Watch:

Key Capabilities:

12-volt Trigger Control: Seamlessly integrate with other components in your system, such as amplifiers, subwoofers, and lighting, for automated power management.
Precision Bass Management: Fine-tune the low-frequency response of your speakers, ensuring seamless integration with your subwoofer and optimal bass performance.

Download PDF

report

WILSON AUDIO Watch Owner's manual

This manual is also suitable for

WILSON AUDIO Watch Owner's manual

Related papers

Other documents