LG 27MT93V User manual

www.lg.com

OWNER’S MANUAL

LED TV*

(CINEMA 3D Smart TV)

27MT93V

27MT93S

*LG LED TV applies LCD screen with LED backlights.

Please read this manual carefully before operating your TV and

retain it for future reference.

2

ENGLISH

TABLE OF CONTENTS

3 LICENSES

4 INSTALLATION PROCEDURE

5 ASSEMBLING AND PREPARING

5 Unpacking

7 - Separate purchase

9 Parts and buttons

10 Lifting and moving the TV

11 Setting up the TV

11 - Attaching the Stand

12 - Mounting on a table

13 - Tidying cables

14 - Using the Kensington security system

14 - Detaching the Stand

15 WATCHING TV

15 Turning the TV on for the first time

17 MAKING CONNECTIONS

17 Connecting an antenna

18 Satellite connection

19 Connecting to a HD receiver, DVD, VCR

player or Gaming device

19 - HDMI connection

20 - HDMI to DVI connection

21 - Component connection

22 - Composite connection

23 - Euro Scart connection

24 - Headphone connection

25 Connecting to a USB

26 Connecting to a CI Module

27 MHL connection

28 Connecting to a wired network

29 Connecting to a PC

30 - HDMI connection

31 - HDMI to DVI connection

32 REMOTE CONTROL

34 MAGIC REMOTE CONTROL

FUNCTIONS

35 Registering Magic Remote Control

35 How to use Magic Remote Control

35 Precautions to Take when Using the

Magic Remote Control

36 USING THE USER GUIDE

37 MAINTENANCE

37 Cleaning Your TV

37 Screen and frame

37 Cabinet and stand

37 Power cord

38 Preventing “Image burn” or “Burn-in” on

your TV screen

39 IF THE QUALITY OF THE 3D

IMAGE IS NOT ACCEPTABLE,

CHECK THE FOLLOWING

40 VIEWING 3D IMAGING

42 TROUBLESHOOTING

42 General

42 Using 3D mode

43 SPECIFICATIONS

ENGLISH

3

LICENSES

Supported licenses may differ by model. For more information of the licenses, visit www.lg.com.

Manufactured under license from Dolby Laboratories. “Dolby “and the

double-D symbol are trademarks of Dolby Laboratories.

The terms HDMI and HDMI High-Definition Multimedia Interface, and the

HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC

in the United States and other countries.

ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a

subsidiary of Rovi Corporation. This is an official DivX Certified® device that

plays DivX video. Visit divx.com for more information and software tools to

convert your files into DivX videos.

ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be

registered in order to play purchased DivX Video-on-Demand (VOD) movies.

To obtain your registration code, locate the DivX VOD section in your device

setup menu. Go to vod.divx.com for more information on how to complete

your registration.

DivX Certified® to play DivX® video up to HD 1080p, including premium

content.

DivX®, DivX Certified® and associated logos are trademarks of Rovi

Corporation or its subsidiaries and are used under license.

Covered by one or more of the following U.S. patents: 7,295,673; 7,460,668;

7,515,710; 7,519,274

Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380;

6,487,535 & other U.S. and worldwide patents issued & pending. DTS, the

Symbol, & DTS and the Symbol together are registered trademarks & DTS 2.0

Channel is a trademark of DTS, Inc. Product includes software.

©

ENGLISH

4

INSTALLATION PROCEDURE

1

Open the package and make sure all the accessories are included.

2

Attach the stand to the TV.

3

Connect an external device to the TV.

y

Image shown may differ from your TV.

y

Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.

y

The available menus and options may differ from the input source or product model that you are

using.

y

New features may be added to this TV in the future.

NOTE

ENGLISH

5

ASSEMBLING AND PREPARING

Unpacking

Check your product box for the following items. If there are any missing accessories, contact the local

dealer where you purchased your product. The illustrations in this manual may differ from the actual

product and accessories.

y

The accessories supplied with your product may vary depending on the model.

y

Product specifications or contents in this manual may be changed without prior notice due to

upgrade of product functions.

NOTE

y

Do not use any pirated items to ensure the safety and product life span.

y

Any damages or injuries by using pirated items are not covered by the warranty.

CAUTION

ENGLISH

6

ASSEMBLING AND PREPARING

Magic Remote Control.

Batteries (AA)

Power Cord

CD (Owner's Manual)/Cards

AC-DC Adapter

Stand Base

Screws 2 EA

Component video cable

3D Glasses(Normal type 2 EA)

- The number of 3D glasses may differ depending on

model or country.

- Image shown may differ from your TV.

Cable holder

MHL passive cable

or

Screw Cover

(Depending on country)

Isolator

or

ㄮᗺ

ⰶᲳ

ⱞⳮ ➎Ẳ㞢

/Q.MENU

S

YRO

EDFN VPDUW

/Q.MENU

Composite audio/video cable

Remote control

Batteries (AAA)

ENGLISH

7

ASSEMBLING AND PREPARING

Separate purchase

Dual play glasses

AG-F2**DP, AG-F3**DP

y

The illustrations in this manual may differ from the actual product and accessories.

y

Separate purchase items can be changed or modified for quality improvement without any

notification.

y

Contact your dealer to buying these items.

y

The model name or design may be changed depending on the upgrade of product

functions,manufacturer’s circumstances or policies.

NOTE

Magic Remote Control

AN-MR400

S

YRO

EDFN VPDUW

/Q.MENU

ENGLISH

8

ASSEMBLING AND PREPARING

y

Antenna Isolator Installation Guide

-

Use this to install TV in a place where there is a voltage difference between TV Set and GND

of antenna signal.

»

If there is a voltage difference between TV Set and GND of antenna signal, the antenna

contact might be heated and excessive heat might cause an accident.

-

You can improve the safety when watching TV by efficiently removing power voltage from TV

antenna. It is recommended to mount the isolator to the wall. If it cannot be mounted to the

wall, mount it on the TV. Avoid disconnecting the antenna Isolator after installation.

-

Before starting, be sure that the TV antenna is connected.

Connect one end of the isolator to cable/antenna jack and the other to TV set or set-top box.

“Equipment connected to the protective earthing of the building installation through the mains

connection or through other equipment with a connection to protective earthing - and to a

cable distribution system using coaxial cable, may in some circumstances create a ﬁre hazard.

Connection to a cable distribution system has therefore to be provided through a device providing

electrical isolation below a certain frequency range (galvanic isolator, see EN 60728-11)”

When applying the RF Isolator, a slight loss of signal sensitivity can occur.

NOTE

ANTENNA/

CABLE IN

Cable / Antenna

Wall

Isolator

1. Connect to TV.

2. Connect to Set-Top box.

or

ENGLISH

9

ASSEMBLING AND PREPARING

Parts and buttons

y

All of the buttons are touch sensitive and can be operated through simple touch with your finger.

NOTE

Touch button Description

Scrolls through the saved programmes.

Adjusts the volume level.

OK

Selects the highlighted menu option or confirms an input.

SETTINGS Accesses the main menus, or saves your input and exits the menus.

INPUT Changes the input source.

/ I

Turns the power on or off.

(19 V )

COMPONENT IN

AUDIO IN(PC)

HP

AV2 IN / AUDIO L R

HDMI IN

5 V 5 V 0.5 A 1.0 A

13/18 V

700 mA Max

LND IN

Remote Control Sensor

Standby Light

y

Lighting On: Turned off

y

Lighting Off: Turned on

Connection panel (See p.17)

Touch buttons on the

bottom of the TV

ENGLISH

10

ASSEMBLING AND PREPARING

y

When holding the TV, the screen should face

away from you to prevent the screen from

scratches.

y

When transporting the TV, do not expose the

TV to jolts or excessive vibration.

y

When transporting the TV, keep the TV

upright, never turn the TV on its side, or tilt

towards the left or right.

Lifting and moving the TV

When moving or lifting the TV, read the following

to prevent the TV from being scratched or

damaged and for save transportation regardless of

its type and size.

y

Avoid touching the screen at all times, as

this may result in damage to the screen or

some of the pixels used to create images.

CAUTION

y

It is recommended to move the TV in the

box or packing material that the TV originally

came in.

y

Before moving or lifting the TV, disconnect

the power cord and all cables.

y

Hold the top and bottom of the TV frame

firmly. Make sure not to hold the transparent

part, speaker, or speaker grill area.

ENGLISH

11

ASSEMBLING AND PREPARING

1

Place the TV with the screen side down on a

flat and cushioned surface.

2

Check the orientation (front and rear) of the

stand base and mount the stand base to the

stand hinge as shown in the figure.

3

Fix two screws into the back of the stand base

and close the screw cover.

y

Tighten the screws firmly to prevent the TV

from tilting forward. Do not over tighten.

CAUTION

Setting up the TV

Attaching the Stand

CAUTION

y

Lay a foam mat or soft protective cloth

on the surface to protect the screen from

damage.

y

When attaching the stand to the TV,

place the screen facing down on a

cushioned table or flat surface to protect

the screen from scratches.

Screw Cover

ENGLISH

12

ASSEMBLING AND PREPARING

Mounting on a table

1

Lift and tilt the TV into its upright position on a

table.

Leave a 10 cm (minimum) space from the wall

for proper ventilation.

2

Connect the AC-DC Adapter and Power Cord

to a wall outlet.

y

Do not place the TV near or on sources of heat,

as this may result in fire or other damage.

CAUTION

10 cm

ENGLISH

13

ASSEMBLING AND PREPARING

y

Disconnect the power cord first, and then

move or install the TV. Otherwise electric

shock may occur.

CAUTION

y

After attachment, if the cable holder is

pulled with excessive force, it may fall off.

CAUTION

y

When you adjust the angle, do not hold the buttom of the TV frame as shown on the following

illustration, as may injure your fingers.

WARNING

y

Tilt from +20 to -5 degrees up or down to

adjust the angle of the TV to suit your view.

NOTE

Front Rear

Tidying cables

1

Attach the cable holder to the edge of stand

body securely.

2

Gather and bind the cables with the supplied

cable holder.

-5 20

:

-5 20

:

-5 20

:

-5 20

:

Cable holder

ENGLISH

14

ASSEMBLING AND PREPARING

Using the Kensington security system

The Kensington security system connector is

located at the back of the TV. For more information

of installation and using, refer to the manual

supplied with the Kensington security system or

visit

http://www.kensington.com

.

Connect the Kensington security system cable

between the TV and a table.

y

The Kensington security system is optional.

You can obtain additional accessories from

most electronics stores.

NOTE

Detaching the Stand

1

Place the TV with the screen side down on a

flat and cushioned surface.

2

Open the screw cover on the back of the stand

base and use a screwdriver to remove the two

screws.

Detach the stand base from the stand hinge as

shown in the figure.

y

Lay a foam mat or soft protective cloth

on the surface to protect the screen from

damage.

y

When detaching the stand to the TV,

place the screen facing down on a

cushioned table or flat surface to protect

the screen from scratches.

CAUTION

Screw Cover

ENGLISH

15

WATCHING TV

Turning the TV on for the first time

When you access the TV for the first time, the initial setting screen appears. Select a language and

customize the basic settings.

1

Connect the power cord to a power outlet.

2

Press on the TV or power button on the remote control to turn the TV on.

The Standby Light is turned off.

3

The initial setting screen appears if you access the TV for the first time.

y

If you do not operate the TV within 40 seconds when the setting menu screen appears, the setting

menus will disappear.

NOTE

WATCHING TV

4

Follow the on-screen instructions to customize your TV according to your preferences.

y

For those countries without confirmed DTV broadcasting standards, some DTV features might not

work, depending on the DTV broadcasting environment.

y

When France is selected for Country, the initial password is not ‘0’, ‘0’, ‘0’, ‘0’ but ‘1’, ‘2’, ‘3’, ‘4’.

y

To display images in the best quality for your home environment, select Home Use mode.

y

Store Demo mode is suitable for the retail environment.

y

If you select Store Demo mode, the previously customized settings will switch to the default

settings of Store Demo mode in 5 minutes.

NOTE

ENGLISH

16

WATCHING TV

y

You can also access Factory Reset by accessing OPTION in the main menus.

NOTE

5

When the basic settings are complete, press OK .

6

To turn the TV off, press on the TV.

The Standby Light is turned on.

y

If you do not complete the initial setting, it will appear whenever you access the TV.

NOTE

y

Disconnect the power cord from the power outlet when you do not use the TV for a long period of

time.

CAUTION

ENGLISH

17

MAKING CONNECTIONS

Connect various external devices to the TV and switch input modes to select an external device. For more

information about an external device’s connection, refer to the manual supplied with each device.

Available external devices are: HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC,

camcorders or cameras, gaming devices, and other external devices.

y

If you record a TV program on a DVD recorder or VCR, make sure to connect the TV signal input

cable to the TV through a DVD recorder or VCR. For more information about recording, refer to the

manual supplied with the connected device.

y

The external device connection may differ from the model.

y

Connect external devices to the TV regardless of the order of the TV port.

MAKING CONNECTIONS

Connecting an antenna

Connect an antenna, cable or cable box to watch TV referring to the following. The illustrations may differ

from the actual accessories and an RF cable is optional.

Connect the TV to a wall antenna socket with an RF cable (75 Ω).

y

Use a signal splitter to use more than 2 TVs.

y

If the image quality is poor, install a signal

amplifier properly to improve the image

quality.

y

If the image quality is poor with an antenna

connected, aim the antenna to the proper

direction.

y

Visit

http://AntennaWeb.org

for more

information about the antenna and cable

connection.

NOTE

y

Make sure not to bend the copper wire of

the RF cable.

y

Complete all connections instructions

between devices, and then connect the

power cord to the power outlet to prevent

damages to your TV.

CAUTION

Copper wire

Wall Antenna Socket

Outdoor Antenna

y

VHF Antenna

y

UHF Antenna

(Not Provided)

NOTE

ENGLISH

18

MAKING CONNECTIONS

13/18 V

700 mA Max

LND IN

Satellite connection

Connect the TV to a satellite dish to a satellite socket with a satellite RF cable (75 Ω).

(Not Provided)

ENGLISH

19

MAKING CONNECTIONS

HDMI IN

COMPONENT I

N

A

UDI

O

IN

(

P

C)

HP

A

V2 IN

/

AUDI

O

L

R

(19 V )

5 V

5

V

0.5 A

1.0 A

13/18 V

700

mA Ma

x

LND I

N

Connecting to a HD receiver, DVD, VCR player or Gaming device

Connect a HD receiver, DVD, VCR player or Gaming device to the TV and select an appropriate input mode.

HDMI connection

HDMI is the best way to connect a device.

Transmits the digital video and audio signals from an external device to the TV. Connect the external device

and the TV with the HDMI cable as shown on the following illustration.

y

Choose any HDMI input port to connect.

y

It does not matter which port you use.

DVD / Blu-Ray / HD Cable Box / HD STB /

Gaming device

y

Use a High Speed HDMI™ Cable.

y

High Speed HDMI™ Cables are tested to carry an HD signal up to 1080p and higher.

y

Supported DTV Audio: MPEG, Dolby Digital.

y

Supported HDMI Audio format: DTS, Dolby Digital, PCM (Up to 192 kHz, 32 kHz / 44.1 kHz / 48 kHz /

88 kHz / 96 kHz / 176 kHz / 192 kHz.)

NOTE

(Not Provided)

ENGLISH

20

MAKING CONNECTIONS

HDMI IN

CO

MP

O

NENT I

N

AUDIO IN(PC)

HP

A

V2 IN

/

A

U

DI

O

L

R

(19 V )

5 V

5

V

0.5 A

1.0 A

13/18 V

7

00 mA Ma

x

L

ND I

N

HDMI to DVI connection

Transmits the digital video signal from an external device to the TV. Connect the external device and the TV

with the HDMI to DVI cable as shown in the following illustration. To transmit an audio signal, connect an

optional audio cable.

DVD / Blu-Ray / HD Cable Box /

HD STB / Gaming device

y

If you do not use an optional external speaker, connect the external device to the TV with the optional

audio cable.

NOTE

(Not Provided)

Page is loading ...

LG 27MT93V User manual

This manual is also suitable for

LG 27MT93V User manual

Related papers

Other documents