Hotpoint GC751TX User guide

Brand: Hotpoint

Model: GC751TX

Category: Hobs

Type: User guide

English

Operating Instructions

HOB

Contents

Operating Instructions,1

Warnings,2

Description of the appliance,3

Installation,4

Start-up and use,8

Precautions and tips,8

Maintenance and care,9

Troubleshooting,9

Product Guarantee and Repair Information,10

GC640BK

GC640IX

GC640TK

GC640TX

GC640WH

GC641IK

GC641IX

GC750X

GC751TX

GCA641IX

GCB641X

GCB751X

GCL640TK

GCL641TX

GF751TX

Warnings

WARNING: The appliance and its accessible parts

become hot during use. Care should be taken to

avoid touching heating elements. Children less than 8

years of age shall be kept away unless continuously

supervised. This appliance can be used by children

aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been

given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards

involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be made

by children without supervision.

WARNING: Unattended cooking on a hob with fat or

oil can be dangerous and may result in re. NEVER

try to extinguish a re with water, but switch off the

appliance and then cover ame e.g. with a lid or a

re blanket.

WARNING: Danger of re: do not store items on the

cooking surfaces.

Never use steam cleaners or pressure cleaners on

the appliance.

Remove any liquid from the lid before opening it. Do

not close the glass cover (if present) when the gas

burners or electric hotplates are still hot.

The appliance is not intended to be operated by

means of an external timer or separate remote

control system.

CAUTION: the use of inappropriate hob guards can

cause accidents.

CAUTION: In case of hotplate glass breakage:

- shut immediately off all burners and any electrical

heating element and isolate the appliance from the

power supply

- do not touch the appliance surface.

Description of the appliance

Overall view

1. Support Grid for COOKWARE

2. GAS BURNERS

3. Control Knobs for GAS BURNERS

4. Ignition for GAS BURNERS

5. SAFETY DEVICES

• GAS BURNERS differ in size and power. Use the diameter of the cookware

to choose the most appropriate burner to cook with.

• Control Knobs for GAS BURNERS adjust the size of the ame.

• GAS BURNER IGNITION enables a specic burner to be lit automatically.

• SAFETY DEVICE stops the gas flow if the flame is accidentally

extinguished.

Installation

! Before operating your new appliance please read this instruction booklet

carefully. It contains important information for safe use, installation and care

of the appliance.

! Please keep these operating instructions for future reference. Pass them on

to possible new owners of the appliance.

Positioning

! Keep packaging material out of the reach of children. It can become a choking

or suffocation hazard (see Precautions and tips).

! The appliance must be installed by a qualied professional according to the

instructions provided. Incorrect installation may cause harm to people and

animals or may damage property.

! This unit may be installed and used only in permanently ventilated rooms

in accordance with current national regulations. The following requirements

must be observed:

• The room must be equipped with an air extraction system that expels

any combustion fumes. This may consist of a hood or an electric fan that

automatically starts each time the appliance is switched on.

In a chimney stack or branched flue.

(exclusively for cooking appliances)

Directly to

the Outside

• The room must also allow proper air circulation, as air is needed for

combustion to occur normally. The ow of air must not be less than 2 m

per kW of installed power.

The air circulation system may take air directly

from the outside by means of a pipe with an

inner cross section of at least 100 cm

; the

opening must not be vulnerable to any type

of blockages.

The system can also provide the air needed for

combustion indirectly, i.e. from adjacent rooms

tted with air circulation tubes as described

above. However, these rooms must not be

communal rooms, bedrooms or rooms that

may present a re hazard.

• Intensive and prolonged use of the appliance may necessitate

supplemental ventilation, e.g. opening a window or increasing the power

of the air intake system (if present).

• Liquid petroleum gas sinks to the oor as it is heavier than air. Therefore,

rooms containing LPG cylinders must also be equipped with vents to allow

gas to escape in the event of a leak. As a result LPG cylinders, whether

partially or completely full, must not be installed or stored in rooms or

storage areas that are below ground level (cellars, etc.). It is advisable to

keep only the cylinder being used in the room, positioned so that it is not

subject to heat produced by external sources (ovens, replaces, stoves,

etc. ) which could raise the temperature of the cylinder above 50°C.

Examples of

ventilation holes

for comburant air.

Enlarging the ventilation slot

between window and floor.

Adjacent

Room

Room to be

Vented

Fitting the appliance

The following precautions must be taken when installing the hob:

• Kitchen cabinets adjacent to the appliance and taller than the top of the

hob must be at least 200 mm from the edge of the hob.

• Hoods must be installed according to their relative installation instruction

manuals and at a minimum distance of 650 mm from the hob (see gure).

• Place the wall cabinets adjacent to the hood at a minimum height of 420

mm from the hob (see gure).

If the hob is installed beneath a wall cabinet,

the latter must be situated at a minimum of 700

mm above the hob.

• The installation cavity should have the dimensions indicated in the gure.

Fastening hooks are provided, allowing you to fasten the hob to tops that

are between 20 and 40 mm thick. To ensure the hob is securely fastened

to the top, we recommend you use all the hooks provided.

555 mm

55 mm

475 mm

Before the installation remove the grids and burners from the hob and turn it

upside down, making sure you don’t damage the thermocouples and spark

plugs.

Apply the seals that come with the

appliance along the outer edges of

the hob to prevent any passage of air,

humidity and water (see Figure).

For proper application make sure the

surfaces to be sealed are clean, dry and

free of any grease/oil.

Hook fastening diagram

Hooking position for top H=20mm Hooking position for top H=30mm

Front

Hooking position for top H=40mm Back

! Use the hooks contained in the “accessory pack”.

600mm min.

420mm min.

650mm min.

• Where the hob is not installed over a built-in oven, a wooden panel must

be installed as insulation. This must be placed at a minimum distance of

20 mm from the lower part of the hob.

Ventilation

To ensure adequate ventilation, the back panel of the cabinet must be

removed. It is advisable to install the oven so that it rests on two strips of

wood, or on a completely at surface with an opening of at least 45 x 560

mm (see diagrams).

560 mm.

45 mm.

Where a hob is installed above an oven without a forced ventilation cooling

system, adequate ventilation must be provided inside the cabinet by means

of air holes through which air can pass (see gure).

Electrical connection

! THIS APPLIANCE MUST BE EARTHED.

The hob is designed to work with alternating current, the supply voltage and

frequency indicated on the rating plate (situated under the hob). Make sure

that the local supply voltage corresponds to the voltage indicated on the

rating plate.

Connecting the supply cable to the mains electricity supply

For models supplied without a plug, t a standard plug suitable for the load

indicated on the rating plate, onto a cable and connect to a suitable socket.

To connect direct to the mains supply, a double pole switch with a contact

separation of at least 3mm suitable for the load and complying with current

standards and regulations must be tted between the appliance and the

mains supply outlet.

The green-yellow earth wire must not be interrupted by the switch.

The supply cable must be positioned so that no part of it reaches a temperature

of 50°C above room temperature. For installation above a built-under

oven, the hob and the oven must be connected separately to the electricity

supply, both for safetly reasons and for easy removal of the oven for repair,

maintenance etc.

DO NOT use adapters as they could cause overheating or burning.

Before connecting to the power supply, make sure that:

• the limiter switch and the domestic system can withstand the load from

the appliance (see rating plate).

• the supply system is efciently earthed according to standards and laws

in force.

• the socket or double-pole switch are easily accessible when the appliance

is installed.

! The wires in the mains lead are coloured in accordance with the following

code:

Green & Yellow - Earth

Blue - Neutral

Brown - Live

As the colours of the wires in the mains lead may not correspond with the

coloured markings identifying the terminals in your plug, proceed as follows:

Connect the Green & Yellow wire to terminal marked “E” or or coloured

Green or Green & Yellow.

Connect the Brown wire to the terminal marked “L” or coloured Red or Brown.

Connect the Blue wire to the terminal marked “N” or coloured Black or Blue.

FAILURE TO OBSERVE THE ACCIDENT-PREVENTION REGULATIONS

RELIEVES THE MANUFACTURER OF ALL LIABILITY.

Replacing the cable

Use a rubber cable of the type H05RR-F with a suitable cross section 3 x

0.75 mm².

The yellow-green earth wire must be 2-3 cm longer than the other wires.

Gas connection

The appliance should be connected to the main gas supply or to a gas

cylinder in compliance with current national regulations. Before carrying out

the connection, make sure the cooker is compatible with the gas supply you

wish to use. If this is not the case, follow the instructions indicated in the

paragraph “Adapting to different types of gas.”

When using liquid gas from a cylinder, install a pressure regulator which

complies with current national regulations.

! Check that the pressure of the gas supply is consistent with the values indicated

in Table 1 (“Burner and nozzle specications”). This will ensure the safe operation

and longevity of your appliance while maintaining efcient energy consumption.

Connection with a rigid pipe (copper or steel)

! Connection to the gas system must be carried out in such a way as not to

place any strain of any kind on the appliance.

There is an adjustable L-shaped pipe tting on the appliance supply ramp

and this is tted with a seal in order to prevent leaks. The seal must always

be replaced after rotating the pipe tting (seal provided with appliance). The

gas supply pipe tting is a threaded 1/2 gas cylindrical male attachment.

Connecting a flexible jointless stainless steel pipe to a threaded

attachment

The gas supply pipe tting is a threaded 1/2 gas cylindrical male attachment.

These pipes must be installed so that they are never longer than 2000 mm

when fully extended. Once connection has been carried out, make sure that

the exible metal pipe does not touch any moving parts and is not compressed.

! Only use pipes and seals that comply with current national regulations.

Checking the tightness of the connection

! When the installation process is complete, check the pipe ttings for leaks

using a soapy solution. Never use a ame.

Adapting to different types of gas

To adapt the hob to a different type of gas other than default type (indicated

on the rating plate at the base of the hob or on the packaging), the burner

nozzles should be replaced as follows:

1. Remove the hob grids and slide the burners off their seats.

2. Unscrew the nozzles using a 7 mm socket spanner, and replace them

with nozzles for the new type of gas (see table 1 “Burner and nozzle

characteristics”).

3. Reassemble the parts following the above procedure in the reverse order.

4. Once this procedure is nished, replace the old rating sticker with one

indicating the new type of gas used. Sticker are available from any of our

Service Centres.

Replacing the Triple ring burner nozzles

1. Remove the pan supports and lift the burners out of their housing. The

burner consists of two separate parts (see pictures).

2. Unscrew the nozzles using a 7 mm socket spanner. Replace the nozzles

with models that are congured for use with the new type of gas (see Table

1). The two nozzles have the same hole diameter.

3. Replace all the components by completing the above operations in reverse

order.

• Adjusting the burners’ primary air

Does not require adjusting.

• Setting the burners to minimum

1. Turn the tap to the low ame position;

2. Remove the knob and adjust the adjustment screw, which is positioned

in or next to the tap pin, until the ame is small but steady.

3. Having adjusted the ame to the required low setting, while the burner is

alight, quickly change the position of the knob from minimum to maximum

and vice versa several times, checking that the ame does not go out.

4. Some appliances have a safety device (thermocouple) tted. If the device

fails to work when the burners are set to the low ame setting, increase

this low ame setting using the adjusting screw.

5. Once the adjustment has been made, replace the seals on the by-passes

using sealing wax or a similar substance.

! If the appliance is connected to liquid gas, the regulation screw must be

fastened as tightly as possible.

! Once this procedure is nished, replace the old rating sticker with one

indicating the new type of gas used. Stickers are available from any of our

Service Centres.

! Should the gas pressure used be different (or vary slightly) from the

recommended pressure, a suitable pressure regulator must be tted to the

inlet pipe (in order to comply with current national regulations).

Electrical

connections

DATA PLATE

EU Regulation no. 66/2014 implementing

Directive 2009/125/EC.

standard EN 30-2-1

ECODESIGN

see data plate

This appliance conforms to the following

European Economic Community directives:

- 2006/95/EC dated 12/12/06 (Low Voltage)

and subsequent amendments

- 2004/108/EC dated 15/12/04

(Electromagnetic Compatibility) and

subsequent amendments

- 93/68/EEC dated 22/07/93 and subsequent

amendments.

- 2009/142/EC dated 30/11/06 (Gas) and

subsequent amendments

- 2012/19/EU and subsequent amendments.

GC750X

GC751X

GC751TX

GF751TX

GC640IX

GC640WH

GC640BK

GC641IX

GCA641IX

GCB641X

GCB641IK

GCL640TK

GCL641TX

GC640TK

Burner Diameter Thermal Thermal By-pass Nozzle Flow* Thermal Nozzle Flow*

power power 1/100 1/100 (g/h) power 1/100 (l/h)

kW kW kW

(p.c.s.*) (p.c.s.*) (p.c.s.*)

(mm) Reduced Nominal (mm) (mm) *** ** Nominal (mm)

Supply pressures Nominal (mbar)

Minimum (mbar)

Maximum (mbar)

28-30

Fast (R)

Reduced Fast (RR)

Semi Fast (S)

Auxiliary (A)

Triple Crown (TC)

Ultrarapid (UR)

100

130

100

0.70

0.40

1.50

0.70

3.00

2.60

1.65

1.00

3.30

3.40

65x2

218

189

120

240

247

214

186

118

236

243

3.00

2.60

1.65

1.00

3.60

3.40

132 (H)

122 (H)

96 (Z)

79 (6)

103x2

138 (H)

286

248

157

343

324

Burner and nozzle specifications

At 15°C and 1013,25 mbar - dry gas

Propane P. C.S. = 50.37 MJ/Kg

***

Butane P. C.S. = 49.47 MJ/Kg

Natural P. C.S. = 37.78 MJ/m³

Table 1 Liquid Gas Natural Gas

7,30 (531 g/h - G30) (521 g/h - G31)

GC640IX

GC640WH

GC640BK

GC641IX

GCA641IX

GCB641X

GC641IK

II2H3+

Gas section

Rated power (kW)Class

Model

Electric section

220-240V~ 50/60Hz

Voltage and frequency

(1)

Power (W)

0,6

The values in g/h refer to the capacities with liquid gas (Butane, Propane).

(1)

GC640TK

GCL641TX

GCL640TK

GC751TX

GF751TX

II2H3+ 8,55 (622 g/h - G30) (611 g/h - G31)

II2H3+ 10,20 (742 g/h - G30) (728 g/h - G31)

220-240V~ 50/60Hz

0,6

GC750X

GCB751X

II2H3+ 10,30 (749 g/h - G30) (736 g/h - G31) 220-240V~ 50/60Hz

0,6

Start-up and use

! The position of the corresponding gas burner is shown on every knob.

Gas burners

Each burner can be adjusted to one of the following settings using the

corresponding control knob:

● Off

Maximum

Minimum

To light one of the burners, hold a lit match or lighter near the burner and, at

the same time, press down and turn the corresponding knob anti-clockwise

to the maximum setting.

Since the burner is tted with a safety device, the knob should be pressed

for approximately 2-3 seconds to allow the automatic device keeping the

ame alight to heat up.

! If a ame is accidentally extinguished, turn off the control knob and wait for

at least 1 minute before trying to relight it.

To switch off the burner, turn the knob in a clockwise direction until it stops

(when reaches the “●” position).

Practical advice on using the burners

To ensure the burners operate efciently:

• Use appropriate cookware for each burner (see table) so that the ames

do not extend beyond the bottom of the cookware.

• Always use cookware with a at base and a cover.

• When the contents of the pan reach boiling point, turn the knob to minimum.

Rapid (R)

Reduced Rapid (RR)

Semi Rapid (S)

Auxiliary (A)

Triple Crown (TC)

Ø Cookware Diameter (cm)

24 - 26

16 - 20

10 - 14

24 - 26

Burner

Pans to be used on 60 cm hobs

Reduced Rapid (RR)

Semi-Rapid (S)

Auxiliary (A)

Triple Crown (TC)

Ultra Rapid (UR)

Ø Cookware Diameter (cm)

24 - 26

16 - 20

10 - 14

24 - 26

Burner

Pans to be used on 75 cm hobs

To identify the type of burner, refer to the designs in the section entitled, “Burner

and Nozzle Specications”.

Precautions and tips

! This appliance has been designed and manufactured in compliance with

international safety standards. The following warnings are provided for safety

reasons and must be read carefully.

General safety

• This is a class 3 built-in appliance.

• Gasappliancesrequireregularairexchangetomaintainefcient

operation. When installing the hob, follow the instructions provided

in the paragraph on “Positioning” the appliance.

• These instructions are only valid for the countries whose symbols

appear in the manual and on the serial number plate.

• The appliance was designed for domestic use inside the home and is

not intended for commercial or industrial use.

• The appliance must not be installed outdoors, even in covered areas. It is

extremely dangerous to leave the appliance exposed to rain and storms.

• Do not touch the appliance with bare feet or with wet or damp hands and

feet.

• The appliance must be used by adults only for the preparation of food,

in accordance with the instructions outlined in this booklet. Any other

use of the appliance (e.g. for heating the room) constitutes improper

use and is dangerous. The manufacturer may not be held liable for

any damage resulting from improper, incorrect and unreasonable

use of the appliance.

• The openings used for ventilation and dispersion of heat must never be

covered.

• Always make sure the knobs are in the “●”/“○” position when the appliance

is not in use.

• When unplugging the appliance always pull the plug from the mains socket,

do not pull on the cable.

• Never carry out any cleaning or maintenance work without having detached

the plug from the mains.

• In case of malfunction, under no circumstances should you attempt to repair

the appliance yourself. Repairs carried out by inexperienced persons may

cause injury or further malfunctioning of the appliance. Contact a Service

Centre (see Assistance).

• Always make sure that pan handles are turned towards the centre of the

hob in order to avoid accidental burns.

• Do not close the glass cover (if present) when the gas burners or electric

hotplates are still hot.

• Do not use unstable or deformed pans.

• The appliance should not be operated by people (including children)

with reduced physical, sensory or mental capacities, by inexperienced

individuals or by anyone who is not familiar with the product. These

individuals should, at the very least, be supervised by someone who

assumes responsibility for their safety or receive preliminary instructions

relating to the operation of the appliance.

• Do not let children play with the appliance.

• The appliance is not intended to be operated by means of an external

timer or separate remote-control system.

Disposal

• When disposing of packaging material: observe local legislation so that

the packaging may be reused.

• The European Directive 2012/19/EU on Waste Electrical and Electronic

Equipment (WEEE), requires that old household electrical appliances must

not be disposed of in the normal unsorted municipal waste stream. Old

appliances must be collected separately in order to optimise the recovery

and recycling of the materials they contain and reduce the impact on

human health and the environment.The crossed out “wheeled bin” symbol

on the product reminds you of your obligation, that when you dispose of

the appliance it must be separately collected.

Consumers should contact their local authority or retailer for information

concerning the correct disposal of their old appliance.

Respecting and conserving the environment

• Cook your food in closed pots or pans with well-tting lids and use as little

water as possible. Cooking with the lid off will greatly increase energy

consumption.

• Use purely at pots and pans.

• If you are cooking something that takes a long time, it’s worth using a

pressure cooker, which is twice as fast and saves a third of the energy.

Maintenance and care

Switching the appliance off

Disconnect your appliance from the electricity supply before carrying out

any work on it.

Cleaning the appliance

! Do not use abrasive or corrosive detergents such as stain removers, anti-rust

products, powder detergents or sponges with abrasive surfaces: these may

scratch the surface beyond repair.

! Never use steam cleaners or pressure cleaners on the appliance.

• It is usually enough to wash the hob with a damp sponge and dry it with

absorbent kitchen roll.

• The removable parts of the burners should be washed frequently with

warm water and soap and any burnt-on substances removed.

• For hobs which ligth automatically, the terminal part of the electronic instant

lighting devices should be cleaned frequently and the gas outlet holes

should be checked for blockages.

• Stainless steel can be marked by hard water that has been left on the

surface for a long time, or by aggressive detergents containing phosphorus.

After cleaning, rinse and dry any remaining drops of water.

Gas tap maintenance

Over time, the taps may become jammed or difcult to turn. If this happens,

the tap must be replaced.

! Thisproceduremustbeperformedbyaqualiedtechnicianauthorised

by the manufacturer.

Troubleshooting

It may happen that the appliance does not function properly or at all. Before

calling the service centre for assistance, check if anything can be done. First,

check to see that there are no interruptions in the gas and electrical supplies,

and, in particular, that the gas valves for the mains are open.

Theburnerdoesnotlightortheameisnotevenaroundtheburner.

Check whether:

• The gas holes on the burner are clogged.

• All the movable parts that make up the burner are mounted correctly.

• There are draughts near the appliance.

Theamediesinmodelswithasafetydevice.

Check to make sure that:

• You pressed the knob all the way in.

• You keep the knob pressed in long enough to activate the safety device.

• The gas holes are not blocked in the area corresponding to the safety

device.

The burner does not remain lit when set to minimum.

Check to make sure that:

• The gas holes are not blocked.

• There are no draughts near the appliance.

• The minimum setting has been adjusted properly.

The cookware is unstable.

Check to make sure that:

• The bottom of the cookware is perfectly at.

• The cookware is positioned correctly at the centre of the burner.

• The pan support grids have been positioned correctly.

Product Guarantee and Repair Information

Please note, our advisors will require the following information:

Model number:

Serial number:

Guarantee

12 Months Parts and Labour Guarantee

Your appliance has benefit of our manufacturer’s guarantee, which covers

he cost of breakdown repairs for twelve months from the date of purchase.

his gives you the reassurance that if, within that time, your appliance is proven

be defective because of either workmanship or materials, we will, at our

discretion, either repair or replace the appliance at no cost

to you:

This guarantee is subject to the following conditions

The appliance has been installed and operated correctly and in accordance

with our operating and maintenance instructions

The appliance is used only on the electricity or gas supply printed on the

rating plate.

The appliance has been used for normal domestic purposes only.

The appliance has not been altered, serviced, maintained, dismantled, or

otherwise interfered with by any person not authorised by us

Any repair work must be undertaken by us or our appointed agent.

Any parts removed during repair work or any appliance that is replaced

become our propert

The appliance is used in the United Kingdom or Republic of Ireland.

The guarantee does not cover

Damage resulting from transportation, improper use, neglect or interference

or as a result of improper installation

Replacement of any consumable item or accessory. These include but

are not limited to:plugs,cables,batteries,light bulbs,fluorescent tubes an

starters, covers and filters.

- Replacement of any removable parts made of glass or plastic.

THIS

GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN

SED IN COMMERCIAL OR NON-DOMESTIC PREMISES.

Recycling and Disposal Information

As part of Hotpoint’s continued commitment to helping the environment,

Hotpoint reserves the right to use quality, recycled components to keep down

customer costs and minimise material wastage.

Please dispose of packaging and old appliances carefully. To minimise the

risk of injury to children, remove the door, plug, and cut the mains cable off

flush with the appliance.Dispose of these parts separately to ensure that th

appliance can no longer be plugged into mains socket, and the door cannot

be locked shut.

Repairs and After Sales

For product help and advice, repairs, spare parts or accessories, we’re here

to help.

For local repair engineers - 03448 111 606

ROI - 0818 313 413

UK standard local rate applies

ROI local Irish rate applies

For Parts and Accessories visit:

parts.hotpoint.co.uk/shop

Please remember to register your appliance at www.hotpointservice.co.uk

to activate your 10 year parts guarantee.

195126178.02

03/2015 - XEROX FABRIANO

Indesit Company S.p.A.

iale Aristide Merloni,47

60044 Fabriano (AN)

www.hotpoint.co.uk

Hotpoint GC751TX User guide

Brand: Hotpoint

Model: GC751TX

Category: Hobs

Type: User guide

Download PDF

report

Hotpoint GC751TX User guide

Hotpoint GC751TX User guide

Related papers

Other documents