Metabo MAG 32 Operating instructions

Page is loading ...

2

EN 60745, EN 12717

2006/95/EG, 98/37EG, 2004/108/EG, 2006/42/EG

M 100

-- 230 V 120 V

H

max

mm (in)

260 (10

1

/

4

)260 (10

1

/

4

)

P

1

W 90 110

F

max

N 18000 18000

Amm (in)

110 x 220 (4

5

/

16

x 8

21

/

32

) 110 x 220 (4

5

/

16

x 8

21

/

32

)

mkg(lbs) 22 (48.5) 22 (48.5)

13

Director Innovation, Research and Development

Responsible Person for Documentation

Volker Siegle

17026927_0411 M 100.book Seite 2 Dienstag, 26. April 2011 10:28 10

Page is loading ...

ENGLISH

9

ENG

1 Declaration of Conformity

2 Specified Conditions of Use

3 General Safety Instructions

4 Special Safety Instructions

5Overview

6 Initial Operation

6.1 Assembly

6.2 Power-supply connection

7Use

7.1 Installing safety chain

7.2 Switching on / switch-on sequence

7.3 Switching off drill

7.4 Switching off magnet

7.5 Mounting on the workpiece

7.6 Drilling

8 Cleaning, Maintenance

9 Troubleshooting

10 Accessories

11 Repairs

12 Environmental Protection

13 Technical Specifications

We, being solely responsible, hereby declare that

this product conforms to the standards and direc-

tives specified on page 2.

The magnetic drill stand is designed for use with

the Metabo drill B 32/3.

The magnetic drill stand is designed for fastening

to magnetisable metal and must therefore have

perfect adhesion. In conjunction with the supplied

safety chain, also suitable for working on vertical

and angled surfaces and overhead.

The user bears sole responsibility for damage

caused by improper use.

Generally accepted accident prevention regula-

tions and the enclosed safety information must be

observed.

WARNING

– Reading the operating

instructions will reduce the risk of injury.

WARNING Read all safety warnings and

instructions.

Failure to follow all safety warn-

ings and instructions may result in electric shock,

fire and/or serious injury.

Keep all safety instructions and information for

future reference.

Before using the power tool, carefully read through

and familiarise yourself with all the enclosed safety

information and the Operating Instructions. Keep

all enclosed documentation for future reference,

and pass on your power tool only together with this

documentation.

For your own protection and for the

protection of your power tool pay atten-

tion to all parts of the text that are

marked with this symbol!

When working on angled and vertical

surfaces and overhead, the magnetic drill

stand must be secured with the supplied

clamping chain so that it cannot fall down if the

power supply is interrupted.

When switching of the magnet, or if the power

supply is interrupted, the magnet loses it holding

power. The device executes a dangerous heaving

movement.

Always wear a hard hat when working overhead.

Always wear a safety harness when working on

scaffolds.

Always wear protective goggles, gloves, and suit-

able shoes when working.

Ensure there is no damage to the mains connec-

tion cables, switch and anti-kink device.

The magnet produces magnetic and electromag-

netic fields that can have a negative effect on

medical implants.

Original instructions

Dear Customer,

Thank you for the trust you have placed in us by buying a Metabo power tool. Each Metabo power tool

is carefully tested and subject to strict quality controls by Metabo's quality assurance. Nevertheless, the

service life of a power tool depends to a great extent on you. Please observe the information contained

in these instructions and the enclosed documentation. The more carefully you treat your Metabo power

tool, the longer it will provide dependable service.

Contents

1 Conformity Declaration

2 Specified Use

3 General Safety Instructions

4 Special Safety Instructions

17026927_0411 M 100.book Seite 9 Dienstag, 26. April 2011 10:28 10

10

ENGLISH

ENG

The surface for the electromagnet must be clean

and flat.

The magnet holding power depends on material

thickness and condition.

Paint, zinc and oxide layers reduce the magnet

holding power.

Do not expose the magnetic drill stand to rain and

do not use in wet or potentially explosive rooms.

Before any setting or maintenance work on the

drill, pull the drill plug from the socket of the

magnetic drill stand.

Caution! When the mains plug of the magnetic drill

stand is disconnected, the magnet loses its

holding power.

Observe the Operating Instructions of the drill.

At the socket (4), only connect drills with the

following current consumption:

at 110-120 V: maximum 12 ampere;

at 220-240 V: maximum 9 ampere.

Before use, always check that the

eccentric

(13) is

firmly clamped so that accidental displacement or

rotation of the upper section is not possible.

Wear protective goggles.

Danger - electrical voltage.

Danger - magnetic field.

Persons with pacemakers prohibited.

See page 3.

1

Snap hook of

safety chain

2 Safety chain

3 Holding points

4 Drill socket

5 Slide plate

6 Threaded pins for adjusting backlash of the

side plate

7 Lever

8Spindle

9 Switch for switching on the drill

10 Switch for switching off the drill

11 Switch for switching magnet on and off

12 Magnet block / Magnet

13 Eccentric

14 Screw for securing the drill

15 Holder for securing the drill

16 Clamping ring

17 Clamping ring screw

Before plugging in, check to see that the

rated mains voltage and mains frequency, as

specified on the rating label, match your power

supply.

Check the unit for possible damage: Before

using the unit, protective devices or slightly

damaged components must be carefully checked

for perfect and specified operation. Check that

moving parts are in perfect working order and do

not jam and check whether parts are damaged. All

parts must be correctly installed and fulfil all condi-

tions necessary to ensure perfect operation of the

unit. Damaged protective devices and parts must

be repaired or replaced according to specifica-

tions by an authorised specialist workshop.

6.1 Assembly

1. Screw the 3 levers (7) firmly into the spindle (8).

2. Inserting drill B 32/3:

- Unscrew additional handle from drill (observe

the Operating Instructions of the drill).

- Align the drill so that the thread (into which

the additional handle was screwed) faces the

holder (15).

- Insert the drill collar into the clamping ring

(16).

- Screw the drill with screw (14) onto holder

(15).

- Tighten screw (17) of clamping ring.

- Press switch (10) and set switch (11) to "0"

(so that the drill cannot start up).

- Insert mains plug of drill into socket (4) of

magnetic drill stand.

-

Set continuous operation at the drill.

(

Observe the Operating Instructions of the

drill).

6.2 Mains connection

The magnetic drill stand is in protection class I and

must therefore only be connected to sockets

earthed according to specifications.

If an extension cord is needed, it must be a three-

core lead with a protective (earth) contactor that is

properly connected to both the plug and the

coupler of the cord.

When working outdoors, only use the correspond-

ingly marked extension cable approved for this

purpose.

Regularly check extension cables and replace if

damaged.

5Overview

6 Commissioning

17026927_0411 M 100.book Seite 10 Dienstag, 26. April 2011 10:28 10

ENGLISH

11

ENG

The extension cable must be suitable for the drill

and magnetic drill stand power ratings (see Tech-

nical Specifications). If using a roll of cable, always

roll up the cable completely.

7.1 Installing safety chain

When working on angled and vertical

surfaces and overhead, the magnetic drill

stand must be secured with the supplied

safety

chain

(2) so that is cannot fall down if the power

supply is interrupted.

Fit the

safety chain

(2) so that if the mains

voltage fails the magnetic drill stand is

moved away from the operator.

Caution! Check the

safety chain

(2)

for

damage. Before using the

safety chain

(2),

always check it carefully to ensure it is operating

faultlessly and as specified. If the

safety chain

(2)

is damaged or the snap hook (1) is no longer in

perfect working order, replace the

safety chain

immediately.

-Fit the

safety chain

(2) on one of the two holding

points (3) of the magnetic drill stand.

- Then secure the

safety chain

to another suitable

fastening point or to the material being proc-

essed. Hook the snap hook (1) of the safety chain

into one of the chain links so that the chain is as

taut as possible.

- Check that the snap hook (1) is completely

closed.

The

safety chain

does not substitute the

magnetic force of the magnetic drill stand,

but is simply used to secure against falling in the

event of a voltage failure.

7.2 Switching on / switch-on sequence

For safety reasons, the drill can only be

switched on after the magnet has been

switched on. Please observe the switch-on

sequence.

1. First switch on the magnet: set switch (11) to

"1". When the magnet is switched on, the indi-

cator lamp built into the switch (11) lights up.

2. Wait until this occurs before turning on the drill

at the switch (9).

See also chapter 9.

Note:

The full holding power of the magnet is avail-

able when the drill is switched on.

7.3 Switching off drill

Press switch (10). Wait until the drill has come to a

complete standstill.

7.4

Switching off

magnet

When the magnet is switched off, the magnet

loses its holding power.

Set switch (11) to "0".

7.5 Mounting on the workpiece

To permit the magnetic drill stand to adhere prop-

erly to material that is to be drilled, the surface

must be clean and smooth. Loose rust, dirt or

grease must be removed before mounting the

magnetic drill stand; any welding beads or surface

irregularities must be smoothened. Thin coats of

paint will not impair adhesion. Clean the magnet

block as well (12) if necessary.

After switching the magnet on, hold the handle of

the magnetic drill stand and shake it firmly to

ensure that the unit is adhering properly. If it is not,

then check the condition of the surface of the

material and that of the bottom of the magnet

block. Clean as necessary and try again.

Use on thin steel

The unit adheres best to low-carbon steel that is at

least 12 mm thick.

For drilling a hole into thin steel, a steel plate meas-

uring at least 100 x 200 x 12 mm can be secured

under the material at the place where the magnetic

stand is to be positioned.

Non-ferrous metals

To drill a hole in non-ferrous metal, the steel plate

should be secured on the surface of the material

and the magnetic drill stand then placed on the

steel plate.

Round or cambered surfaces

If you need to drill into a round or cambered

surface, then the magnet block (12) should be

positioned with its longitudinal axis parallel to the

axis of the camber.

The open space between the magnet block and

the camber should be packed with steel wedges or

rods on both sides along the entire length of the

magnet block so that after switching on the

magnet as many as possible magnetic lines of

force are conducted from the magnet pole through

the wedges (or rods) and the material to the

magnet block housing.

Ensure that the steel wedges (rods) on both sides

of the magnet block are distributed such that the

axis of the drill bit is aligned directly to the centre

of curvature; otherwise it could be diverted to one

side.

By shaking the handle of the magnetic drill stand,

make sure that the stand adheres properly to the

material.

7.6 Drilling

- Observe the Operating Instructions of the drill.

7Use

17026927_0411 M 100.book Seite 11 Dienstag, 26. April 2011 10:28 10

12

ENGLISH

ENG

- Centre the position at which the hole is to be

drilled.

- Align the magnetic drill stand so that the drill bit

is near the centre marking.

- Switch on the magnet of the magnetic drill stand

(switch (11)).

- After releasing the eccentric (13), the upper

section of the magnetic drill stand can be rotated

and laterally shifted so that the drill bit is exactly

above the centre marking. Important! Firmly

clamp the eccentric (13) again.

Before use, always check that the

eccentric

(13) is firmly clamped so that accidental

displacement or rotation of the upper section is not

possible.

- Then switch on the drill (switch (9)).

- Start the drilling operation with minimum feeding

force.

- When the drill bit has started to drill, slightly

higher feeding force can be applied. Excessive

feeding force leads to premature wear of the drill

bit. Ensure that the chip flow is regular

- The graduated collar at the spindle (8) is used to

determine the drilling depth.

If (after use) the magnetic drill stand is placed

on a material with low heat-dissipation char-

acteristics for a long period (e.g. plastic), the

magnet must not be switched on because this

could lead to overheating of the magnetic coils.

Perform regular maintenance work, cleaning and

lubrication.

Disconnect the mains plug before starting any

setting, maintenance or repair work.

For lubricating the rack and pinion that moves the

slide plate (5) up and down, a few drops of oil

should be applied occasionally to the rack.

Coat the sliding surfaces of the slide plate (5) with

multi-purpose grease.

Backlash of the slide plate

The backlash of the side plate is set ex works.

The side plate (5) must be adjusted so that while

the slide plate (with motor installed) can still be

moved freely up and down, it will remain in any

position without the weight of the drill pulling it

down.

The backlash of the side plate (5) can be adjusted

as required using the seven threaded pins (6).

Release lock nuts, tighten threaded pins and

retighten lock nuts.

Electronic restart protection (for preventing

accidental restarting)

If, with the drill switched on,

a) the magnet is switched off or

b) the power supply is interrupted,

the drill comes to a standstill.

If the magnet is then reactivated or the power

supply restored, for safety reasons the drill does

not restart automatically (electronic restart protec-

tion). Turn the drill back on at the switch (9)

.

Metabo MAG 32 Operating instructions

This manual is also suitable for

Metabo MAG 32 Operating instructions

in other languages

Related papers

Other documents