Vivo PT-RT-70 is a versatile remote control for various TV ceiling and wall mounts, offering user-friendly features for adjusting and customizing TV positions. With its dedicated buttons, you can effortlessly move your TV up, down, left, or right, ensuring optimal viewing angles from any location in the room.
Programmable Memory Function: The remote includes two memory buttons that allow you to save and recall preferred TV positions. By pressing and holding the memory buttons for a few seconds, you can easily store and access your favorite viewing locations with just a press of a button.
Smooth and Precise Movement: The remote provides smooth and precise control over your TV's movement, enabling you to make fine adjustments to achieve the perfect viewing angle. The responsive buttons and intuitive design make it easy to operate, even for those unfamiliar with remote controls.
Vivo PT-RT-70 is a versatile remote control for various TV ceiling and wall mounts, offering user-friendly features for adjusting and customizing TV positions. With its dedicated buttons, you can effortlessly move your TV up, down, left, or right, ensuring optimal viewing angles from any location in the room.
Programmable Memory Function: The remote includes two memory buttons that allow you to save and recall preferred TV positions. By pressing and holding the memory buttons for a few seconds, you can easily store and access your favorite viewing locations with just a press of a button.
Smooth and Precise Movement: The remote provides smooth and precise control over your TV's movement, enabling you to make fine adjustments to achieve the perfect viewing angle. The responsive buttons and intuitive design make it easy to operate, even for those unfamiliar with remote controls.
Remote for MOUNT-E-FD55 / FD70 / MM070 / WM075
Instruction Manual
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
https://vivo-us.com/products/pt-rt-70
SKU: PT-RT-70
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
2
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage
or injury caused by improper mounting, incorrect assembly, or inappropriate use.
WARNING!
SAVE AND RECALL MEMORY
To save a certain location to memory, press and hold the mem1 or mem2 buttons for 2
seconds. The mount will beep, indicating the position has been saved to memory. To recall
memory locations, press the ( 1 ) or ( 2 ) button. The TV mount will automatically adjust to
saved memory locations 1 or 2.
IF MOUNT IS INSTALLED ON A PITCHED SURFACE:
1. Press and hold the OK button for 6 seconds. The mount will retract to the minimum
(folded) position.
2. Press the down button to lower the TV. Press OK when the TV has reached the fully
lowered position.
3. Press and hold the mem1 button until the mount beeps. Repeat 4 times. Mount will
give a long beep, indicating that the maximum tilt angle has been set. The mount is now
ready for use.
Downward
Movement
Stop Memory Button 1: Press
and hold for 2 seconds,
the mount will beep twice.
Location 1 is saved.
Memory Button 2: Press
and hold for 2 seconds,
the mount will beep twice.
Location 2 is saved.
BUTTON FUNCTIONS
Upward
Movement
STEP 1
Plug the mount in. The mount will beep once, and will be ready for operation.
REMOTE CONTROL OPERATING INSTRUCTIONS
NOTE: The mount relies on gravity for correct operation and will only operate when in the
correct orientation. The mount will not operate while resting on a table or other surface.
MANUAL POSITION ADJUSTMENT
To adjust TV mount to minimum position (resting against the ceiling), simply give it a slight
push. The mount will automatically return to minimum the position.
NOTE: The mount must be lowered using the remote.
Recall Memory
Position 1
Recall Memory
Position 2
Install two AAA batteries (not included) in the remote.
Instructions for MOUNT-E-FD55 / FD70
3
If the original remote has been lost, please contact us for a new one. To pair the replacement
remote with the mount:
1. Use a thin tool (such as a paperclip) to press the small button on the le side of the mount.
The mount will beep once.
2. Press the SET button on the replacement remote. The mount will beep repeatedly for 10
seconds to indicate that the remote is being programmed to the mount. When the beeping has
stopped, the mount will be ready for operation.
REPLACING THE REMOTE CONTROL
If the TV ceiling mount operates abnormally, it may be necessary to perform a reset of the
mount. To reset the TV ceiling mount, unplug the mount from power for 10 seconds and
plug back in. Hold the OK button for 6 seconds to return mount to the minimum (folded)
position. Press the down button and allow mount to fully lower.
RESET MOUNT
Remote Control Range is Too
Short
PROBLEM SOLUTION
Abnormal Operation
Mount Will Not Operate
Abnormal Noise
Replace the batteries. If the problem is not resolved,
please contact us to replace the remote control.
Reset the system by following instructions under
Reset Mount. If problem is not resolved, contact us to
replace the product.
Ensure power supply is properly connected to the
product. If so, ensure power outlet is working. If there
is no beeping sound or red light (power indication) on
the TV mount, please contact us to replace the power
supply.
Please contact us to replace the product.
PAIRING A REMOTE TO MULTIPLE UNITS
The included remote may be paired to multiple units, allowing all installed mounts to be con-
trolled simultaneously. Follow the steps outlined above in "Replacing the Remote Control"
for each mount to pair to a single remote.
To change each unit back to using individual remotes, repeat the programming steps using
the individual remotes for each.
SAVE AND RECALL MEMORY
To save a certain location to memory, press and hold the mem1 or mem2 button for 2
seconds. The mount will beep, indicating the position has been saved to memory. To recall
memory locations, press the ( 1 ) or ( 2 ) button. The TV mount will automatically adjust to
saved memory locations 1 or 2.
Downward
Movement
Memory Button 1 Memory Button 2
BUTTON FUNCTIONS
Upward
Movement
UPWARD/DOWNWARD MOVEMENT
Press and hold the up button to raise the TV. Press and hold the down button to lower the TV.
REMOTE CONTROL OPERATING INSTRUCTIONS
If the original remote has been lost, please contact us for a new one. To pair the replacement
remote with the mount:
1. Use a thin tool (such as a paperclip) to press the small button on the le side of the mount’s
control unit (le box). The mount will beep once.
2. Press the SET button on the replacement remote. The mount will beep repeatedly for 10
seconds to indicate that the remote is being programmed to the mount. When the beeping has
stopped, the mount will be ready for operation.
REPLACING THE REMOTE CONTROL
Recall Memory
Position 1
Recall Memory
Position 2
Install two AAA batteries (not included) in the remote. Plug the mount in. The mount will
beep once, and will be ready for operation.
Retract/Reset
RETRACT TO WALL
To fully raise and retract the arm to the wall, press the OK button. Press any button to stop
the movement if needed.
Instructions for MOUNT-E-MM070
4
If the TV wall mount operates abnormally, it may be necessary to perform a reset of the
mount. To reset the TV wall mount, unplug the mount from power for 10 seconds and plug
back in. Hold the OK button for 5 seconds. The mount will raise to the maximum position
and beep once, then lower to the minimum position and beep twice.
To clear the memory, use a thin tool (such as a paperclip) to press the small button on the
le side of the mount’s control unit (le box). The mount will beep once. Press and hold the
button again for 10 seconds or until the mount beeps twice to confirm clearing.
(NOTE: The memory clearing process may also be necessary if replacing the remote control)
RESET MOUNT
The Mount Will Not Operate
PROBLEM SOLUTION
Abonormal Operation
Remote Control
Range is Too Short
Abnormal Noise
1. The system may be overheating. If the mount beeps
twice aer pressing a button, allow to cool for 12 minutes.
2. The remote may not be paired with the mount. Refer to
REPLACING THE REMOTE CONTROL. 3. Check to make sure
the power cable is plugged in.
1. Reset the TV mount. Refer to RESET MOUNT.
1. Replace the batteries. If the problem is not resolved,
please contact us to replace the remote control.
Please contact us to replace the product.
The TV Stops Moving
1. Ensure there are no cables or objects preventing the
mount from moving. 2. The TV weight may exceed the 77lb
(35kg) weight limit. 3. The motor cable may be damaged.
Reset the mount. If the problem continues, contact us for
replacement.
TROUBLESHOOTING
5
REMOTE CONTROL OPERATING INSTRUCTIONS
Le
Movement
Stop Memory Button 1: Press
and hold for 2 seconds,
the mount will beep twice.
Location 1 is saved.
Memory Button 2: Press
and hold for 2 seconds,
the mount will beep twice.
Location 2 is saved.
BUTTON FUNCTIONS
Right
Movement
Recall Memory
Position 1
Recall Memory
Position 2
Install two AAA batteries (not included) in the remote.
OPERATION
Use le and right buttons to manually swing the mount in and out.
SAVE AND RECALL MEMORY
To save a certain location to memory, press and hold the mem1 or mem2 buttons for 2
seconds. The mount will beep, indicating the position has been saved to memory. To recall
memory locations, press the ( 1 ) or ( 2 ) button. The TV mount will automatically adjust to
saved memory locations 1 or 2.
ERROR INDICATIONS
Over-Current Protection: The unit makes a “beep beep” (2 beeps) once
Sensor indicates the mount is out of range: The unit makes a “beep beep” (2 beeps) twice
Sensor indicates an operating fault: The unit makes a “beep beep” (2 beeps) three times
Unit senses abnormal power: The unit makes a “beep beep” (2 beeps) four times
SWITCH REMOTE DIRECTION
To switch the remote direction, press and hold the up button for 5 seconds and wait for the
mount to beep.
Instructions for MOUNT-E-WM075
6
INCREASE THE SWIVEL RANGE
The default swivel range of the TV mount is 0°-90°.
To increase the swivel range:
1. Adjust the TV wall mount to your desired position manually.
2. Unplug and re-plug the power. Press and hold “mem1” until you hear one beep. Repeat
this step five times until you hear two consecutive beeps; thie new swivel range is now saved
successfully. Note: The max swivel range is 170°.
Remote Control Range is Too
Short
PROBLEM SOLUTION
Abnormal Operation
Mount Will Not Operate
Abnormal Noise
Replace the batteries. If the problem is not resolved,
please contact us to replace the remote control.
Reset the system by following instructions under
Reset Mount. If problem is not resolved, contact us to
replace the product.
Ensure power supply is properly connected to the
product. If so, ensure power outlet is working. If there
is no beeping sound or red light (power indication) on
the TV mount, please contact us to replace the power
supply.
Please contact us to replace the product.
1. Use a thin tool (such as a paperclip) to press the small button on the le side of the mount.
The mount will beep once.
2. Press the SET button on the replacement remote. The mount will beep repeatedly for 10
seconds to indicate that the remote is being programmed to the mount. When the beeping has
stopped, the mount will be ready for operation.
PAIRING THE REMOTE CONTROL
If the TV wall mount operates abnormally, it may be necessary to perform a reset of the
mount. To reset the TV wall mount, unplug the mount from power for 10 seconds and
plug back in. Hold the OK button for 6 seconds to return mount to the minimum (folded)
position.
RESET MOUNT
PAIRING A REMOTE TO MULTIPLE UNITS
The included remote may be paired to multiple units, allowing all installed mounts to be
controlled simultaneously. Follow the steps outlined above in "Pairing the Remote Control"
for each mount to pair to a single remote.
To change each unit back to using individual remotes, repeat the programming steps using
the individual remotes for each.
7
LAST UPDATED: 07/14/22
REV2.2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Vivo PT-RT-70 is a versatile remote control for various TV ceiling and wall mounts, offering user-friendly features for adjusting and customizing TV positions. With its dedicated buttons, you can effortlessly move your TV up, down, left, or right, ensuring optimal viewing angles from any location in the room.
Programmable Memory Function: The remote includes two memory buttons that allow you to save and recall preferred TV positions. By pressing and holding the memory buttons for a few seconds, you can easily store and access your favorite viewing locations with just a press of a button.
Smooth and Precise Movement: The remote provides smooth and precise control over your TV's movement, enabling you to make fine adjustments to achieve the perfect viewing angle. The responsive buttons and intuitive design make it easy to operate, even for those unfamiliar with remote controls.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Vivo MOUNT-E-FD55 User guide
-
Vivo FBA_MOUNT-E-FD55 User guide
-
-
-
-
-
Vivo MOUNT-E-FD85 Electric Flip Down Ceiling TV Mount User manual
-
-
-
Other documents
-
V I V O MOUNT-E-FD85 User manual
-
Ricoo SE0564 User manual
-
Toshiba FT-9003 User guide
-
-
V I V O DESK-V133E User manual
-
Toshiba FT-9005 User guide
-
Ricoo SE2544 User manual
-
-
-
Speaka SP-TVCM-520 Motorized TV Ceiling Mount User manual