Digital Watchdog DW-VA1P410T User guide

Brand: Digital Watchdog

Model: DW-VA1P410T

Type: User guide

The Digital Watchdog DW-VA1P410T is a powerful surveillance solution for your home or business. With 10 channels, you can connect up to 10 cameras to monitor your property from anywhere, anytime. The DW-VA1P410T supports HD-Analog, HD-TVI, and Analog signal up to 960H, providing you with crystal-clear images. The automatic signal detection feature eliminates the need for manual configuration, making setup a breeze. You can easily access and control your system using the included USB mouse or the DW Mobile Plus™ app on your smartphone or tablet.

Default Login Information Username: admin Password: no password

Quick Start Guide

NOTE: Download all your support materials and tools in one place

1. Go to: http://www.digital-watchdog.com/support-download/

2. Search for your product by entering the part number in the “Search by Product” search bar.

Results for applicable part numbers will populate automatically based on the part number you enter.

3. Click “Search”. All supported materials, including manuals, Quick Start Guides (QSG), software

and ﬁrmware will appear in the results.

Tel: +1 (866) 446-3595 / (813) 888-9555

Technical Support Hours: 9:00AM – 8:00PM EST, Monday thru Friday

digital-watchdog.com

Attention: This document is intended to serve as a quick reference for initial set-up. It is

recommended that the user read the entire instruction manual for complete and proper installation

and usage.

4-Channel 8-Channel 16-Channel

DW-VA1P41T DW-VA1P81T DW-VA1P162T

DW-VA1P42T DW-VA1P82T DW-VA1P163T

DW-VA1P43T DW-VA1P83T DW-VA1P164T

DW-VA1P44T DW-VA1P84T DW-VA1P166T

DW-VA1P46T DW-VA1P86T DW-VA1P168T

DW-VA1P46T DW-VA1P88T DW-VA1P1 610T

DW-VA1P410T DW-VA1P81 0T DW-VA1P1612T

DW-VA1P1616T

DW-VA1P1 620T

Quick Start Guide

1. Mount and install all necessary cameras and external devices. Refer to their individual

manuals for additional information.

2. The DVR supports the following analog signals:

• HD-Analog

• HD-TVI

• Analog signal up to 960H

The DVR supports cameras up to 5MP in resolution. Please refer to the product’s data

sheet and full manual for recording speciﬁcations per product.

3. The DVR supports automatic signal detection. This means you do not have to perform

any additional steps to assign signals to each BNC input. The DVR will detect the proper

signal automatically.

4. Place the DVR in its ﬁnal position. See installation tips below.

5. Connect all necessary cables to the DVR.

6. Once all additional devices have been properly connected

to the DVR, connect the DVR to an appropriate power supply.

The DVR will boot up automatically.

1. When the DVR boots up, it will be in

protective mode. This means you will not

be able to access the DVR’s setup menu

until you login.

2. To unlock the DVR, right-click anywhere

on the screen. The login screen will

appear. (Default Username / Password:

admin / no password)

3. When the DVR boots up for the ﬁrst time,

you will be guided through the Startup

Wizard.

1. Make sure the cameras and the monitors are properly connected to the DVR.

2. The DVR should be placed in a dust and moisture free environment. It must never

be directly exposed to sunlight. A room temperature is highly recommended to reduce

the chance of overheating, (room temperature is considered as 68~78°F), which may

cause the DVR to become unstable.

3. During the boot up process, the DVR should not be interrupted by pressing any

buttons on the mouse. Do not unplug the power adapter or turn the DVR o during the

boot up process.

4. A UPS (uninterrupted power supply) is highly recommended to prevent damage to the

DVR during a power outage.

STEP 1 – CONNECTING THE DVR STEP 2 – POWERING UP THE DVR

SAFETY TIPS

NOTE: HD Monitor output and VGA output cannot be used at the same time for dual monitoring.

To prevent the DVR from overheating, do not operate it in an area that exceeds the maximum

recommended ambient temperature of 104°F (40°C). To prevent airﬂow restriction, allow

at least 3 inches (7.6 cm) of clearance around the ventilation openings.

Model Power consumption

DW-VA1P4xT DC12V, 1.5A

DW-VA1P8xT DC 12V, 3.3A

DW-VA1P1 6xT DC12V, 5A

WHAT’S IN THE BOX

QSG manual 1 Set DC 12V power adapter 1 Set

IR remote control

(optional) 1 Set Rubber mounts – 4pcs 1 Set

USB mouse 1 Set

VGA

ADAPTOR

POWER ON/OFF SWITCH

ANALOG/TVI/AHD CAMERA

SPOT

MONITOR

AUDIO IN

SPOT

ALARM

IN/OUT

VGA MONITOR

PTZ CAMERA

NETWORK CABLE

AUDIO OUT

HD MONITOR

USB MOUSE

https://manual-hub.com/

1. Follow the startup wizard’s instructions to setup the DVR’s basic settings, including

language, date/time and network. You may not need to change any default settings to

properly set up your system. At any time, you can skip steps, go back, or exit the wizard

and setup the DVR manually.

2. Set the DVR’s network settings to match your network’s requirements. It is

recommended to set the network type to “AUTO

CONN.” and let the DVR auto-detect the network’s

settings. Then, change the type to static. Please

contact your network administrator for additional

information. Press “APPLY” to save and “NEXT” to

move to the next step. Adjust the DDNS settings as

needed, or refer to the PathFinder™ option instead

after initial setup. See STEP 6 - MOBILE APP

REMOTE MONITORING.

3. If this is your ﬁrst time powering up the DVR, You are

encouraged to use the setup wizard. If you prefer to

manually go through the DVR’s settings to your preference, you can exit the setup

wizard at any time.

To add a UTC or PTZ camera:

1. Right-click anywhere on the screen

and go to “MENU” > “DECIVE” > “PTZ”

2. Camera type will be auto-detected and displayed

under the camera tab. Protocol should match the

camera type detected.

- HD-A(C) -> legacy HD-Analog signal type camera.

- HD-A/HD-TVI -> HD-Analog and HD-TVI signal

type camera.

- HD-TVI-> HD-TVI signal type camera

(DW default signal type).

3. To control the camera’s menu and settings, press the

“PROGRAM” button under the “CONTROL”. See user

manual for more information.

1. Navigation – use the included USB mouse to navigate around the DVR’s monitoring and

Setup pages.

a. To access the menu bar – move the mouse’s cursor

to the bottom of the display area to show the menu

bar. You can also display it constantly by pressing

the pin icon on the right side.

b. To access the quick menu options, right-click

anywhere on the screen. This will take you to the quick menu

options, which include:

• “DISPLAY MODE” Options

• “DIGITAL ZOOM”, “PTZ” control and “FREEZE” image

(on supported cameras)

• “ADD BOOKMARK” video

• Instant “PLAYBACK”, “SEARCH” and “THUMBNAIL SEARCH”

• Recording status and analysis system monitoring

• Access to the “HEALTH CHECK” and open the main “MENU”.

2. Help – For your convenience, the help button located at

the bottom left of setup screens includes basic

information and explanation of the features and settings

in that page, for on-the-go information.

Quick Start Guide

Speciﬁcations and pricing are subject to change without notice.

STEP 3 – STARTUP WIZARD

STEP 4 – UTC AND PTZ CAMERA CONTROL

STEP 6 – MOBILE APP REMOTE MONITORING

You can monitor your system from DW’s Mobile Plus™ app with no need for complicated

port forwarding! To enable the QR code on your DVR:

1. Right-click anywhere on the DVR’s screen and

go to “MENU” > “NETWORK” > “PATHFINDER™”

2. Check the box next to ‘USE PATHFINDER’. Click

Save.

3. A mobile access QR code will appear on the

right side of the screen. Status at the bottom of

the screen should say “PATHFINDER™ SERVICE

ACTIVATED”.

To view the DVR on your mobile app:

1. Go to the Google Play Store or Apple App store

and download the latest DW Mobile Plus™ app.

2. To add a new VMAX® A1 Plus™ device- Launch

the DW Mobile Plus™ application on your

Android® or Apple® smart-phone or tablet.

3. Go to the Site menu to register a new site with

the QR code scan.

4. Press QR icon next to the Host ﬁeld.

5. Move the camera angle to QR code on DVR. The

camera will capture the QR code automatically

once all four corners of the code are registered

in the camera’s frame properly.

6. Once the camera registers the QR code from

the DVR, the IP address ﬁeld will show the DVR’s

MAC address information.

7. Complete the new device’s registration

information by adding the device name, port

number, user-name and password. Select

“SAVE” to complete the registration.

8. The new site will appear in your sites list.

Rev Date: 06/19

STEP 5 – MONITOR YOUR SYSTEM

EXISTING COAX CABLE

COAX CABLE

CAMERA

DVR

OSD

CAMERA SETTINGS

EXPOSURE

COLOR

DAY/ N IG H T

MOTION

The DVR supports complete camera

control via the coaxial connection (UTC).

There is no need for an additional RS485

connection between the camera and the

DVR in order to control the camera. This

feature must also be supported on the

camera’s side.

NOTE: If you are connecting a camera via UTC protocol,

baudrate and address settings will be disabled.

https://manual-hub.com/

Digital Watchdog DW-VA1P410T User guide

Digital Watchdog DW-VA1P410T User guide

Digital Watchdog DW-VA1P410T User guide

Related papers

Other documents