Sealey SDH30.V3 User manual

Brand: Sealey

Model: SDH30.V3

Category: Dehumidifiers

Type: User manual

Sealey SDH30.V3 is a powerful dehumidifier with a capacity to remove up to 30 liters of water per day, preventing mildew and mold build-up. It features an auto-defrost function and a washable air filter. The refrigerant is environmentally friendly R290. It can be connected to a drain hose for continuous operation and is mounted on castors for easy movement.

30L INDUSTRIAL DEHUMIDIFIER

MODEL NO: SDH30.V3

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these

instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY

1.1. ELECTRICAL SAFETY

 WARNING! It is the user’s responsibility to check the following:

Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all

electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical

products. You may obtain an RCD by contacting your local Sealey dealer.

If the unit is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance

Test) tested.

Electrical safety information, it is important that the following information is read and understood.

1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.

1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.

1.1.3. IMPORTANT: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is tted with the

correct fuse - see fuse rating in these instructions.

8 DO NOT pull or carry the appliance by the power cable.

8 DO NOT pull the plug from the socket by the cable.

8 DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or

replaced immediately by a qualied electrician.

1.1.4. This product is tted with a BS1363/A 13 Amp 3 pin plug.

If the cable or plug is damaged during use, switch the electricity supply and remove from use.

Ensure that repairs are carried out by a qualied electrician.

Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualied electrician.

a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.

b) Connect the BROWN live wire to the live terminal ‘L’.

c) Connect the BLUE neutral wire to the neutral terminal ‘N’.

Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.

Sealey recommend that repairs are carried out by a qualied electrician.

1.2. GENERAL SAFETY

9 Check that the dehumidier is in sound condition and good working order. Take immediate action to repair or replace damaged parts.

9 Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

8 DO NOT stand or place any object less than 10cm from the front or rear of the unit.

8 DO NOT obstruct the air intakes or outlets of the dehumidifier.

8 DO NOT place any object into the outlets - the unit has a fan running at high speed, contact with this will cause injury.

8 DO NOT operate the dehumidifier when you are tired or under the influence of alcohol, drugs or intoxicating medication.

8 DO NOT switch the dehumidifier off by disconnecting it from the mains. ALWAYS switch to the “OFF” position first.

8 DO NOT remove the float lever from the water collection tank.

8 DO NOT connect or disconnect the plug from the mains with wet hands.

9 Always discard the water from the collection tank, DO NOT use it for any other purpose.

9 Place the dehumidier on a level and stable surface.

8 DO NOT use the dehumidier at ambient temperatures below 5°C.

8 DO NOT use the dehumidier outside.

9 When using continuous draining, make sure that the drain hose is positioned correctly.

9 Ensure that heating appliances are not exposed to the flow of air from the dehumidifier.

9 Before attempting to move the dehumidifier, empty the contents of the collection tank.

9 Switch off and disconnect it from the mains before attempting any cleaning or other maintenance work.

9 Ensure that the dehumidifier is correctly turned off when not in use, and stored in a safe, dry area, out of reach of children.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental

capabilities or lack of experience or knowledge if they have been given supervision or instruction concerning use of the appliance in

a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall

not be made by children without supervision.

Original Language Version

Refer to

instructions

Do not cover Indoor use only Caution:

Risk of re

Recommended fuse rating

13 Amp

SDH30.V3 Issue 2 (2) 16/05/22

2. INTRODUCTION

Powerful dehumidication capacity, extracts up to 30 litres of water per day. Removes excess moisture from air, preventing build-up of mildew

and mould. Features auto-defrost function, which activates if the room temperature falls too low. The unit has a 24hr timer function for delay

starting and auto-shut-o. Washable air lter. Refrigerant is environmentally friendly R290. May be connected to a drain hose for continuous

operation. Mounted on castors for manoeuvrability.

3. SPECIFICATION

Model No.:............................................................ SDH30.V3

CO2 Equivalent: .......................................................... 0.0006t

Condensate Tank: .............................. 7L (with Auto Shut-O)

Dehumidifying Capacity: ..................... 30L/day(300CRH80%)

Electrical Plug Type: ................................................ 3-Pin BS

Freezing Pressure(Max): ............................................2.5MPa

Global Warming Potential (Rating) ....................................... 3

IP Rating: ........................................................................IP22

Maximum Airow: ..................................................... 300m3/hr

Power: ................. 420W (270C RH60%) 500W(300C RH80%)

Refrigerant: ........................................................R290/0.12kg

Steaming Pressure (Max): .........................................1.0MPa

Supply: ...........................................................................230V

Working space: ....................................................... 50-120m³

Working Temperature: ................................................. 5-350C

4. ASSEMBLY

4.1. With unit tipped forward, x axle (g.1) to underside of unit with the four screws provided.

4.2. Slide wheels onto the axle and x in place using the plain washer and locking nut provided.

4.3. Remove the screws from the handle hinge point, rotate the handle to the upright position and re-t the screws to x it in place.

NOTE: Once upright, DO NOT use the unit for at least 2 hours.

4.4. WATER TANK USAGE

4.5. You may use the water tank in two ways.

4.5.1. DIRECT USE. When the water tank is full, the machine automatically shuts down and enters the standby state, the LED displays

the “Full Water” signal and the dehumidier will alarm. When the water tank is emptied and put in place again, the dehumidier can

continue its performance.

4.6. CONTINUOUS DRAINING

4.6.1. If there is a place suitable for draining, continuous draining can be carried out. The continuous operation enables the dehumidfying

operation to continue uninterrupted.

4.6.2. Turn off the dehumidifier, disconnect the power plug and remove the water collection tank.

4.6.3. Remove the plug from the bottom right hand side of the tank (fig.2) and attach a suitable length hose.

4.6.4. It should have an inner diameter of 5/8” and secure with a hose clip.

4.6.5. Thread the hose through the hole in the bottom right hand side of the base of the unit, insert the tank ensuring the hose is not kinked.

4.6.6. Continue to use the dehumidifier as normal.

NOTE: When using continuous drainage, the drainage pipe shall not be set higher than the water tank.

Original Language Version

g.1

g.2

Locknut & washer

SDH30.V3 Issue 2 (2) 16/05/22

Original Language Version

5. OPERATION

NOTE: Efficiency of the dehumidifier is influenced by the air outside the room. For operating efficiency, try to avoid opening and closing the

windows and doors. For best performance, operate the dehumidifier within the usable operating temperature.

5.1. OPERATION

5.1.1. Plug the unit in to the mains socket, a beep will be heard when inserting the plug.

5.1.2. Press the “ON/OFF” switch and the operation light will illuminate, the humidity display will light to display the previous set humidity.

The initial setting for humidity is 60%, after 3 seconds the display will show the current humidity.

5.1.3. Press the humidity up or down buttons to adjust to the desired humidity required.

If the required humidity is 3% below the current humidity the unit will start automatically, if the set humidity is 3% more than the current

humidity the dehumidifier will automatically stop.

5.1.4. When setting the humidity to less than 30%, the unit will run continuously and the display will read “CO”.

5.1.5. To shut the dehumidifier down press the “ON/OFF” switch.

NOTE: If the humidity setting is greater than the current humidity the unit will not run.

 WARNING! The fan motor and compressor must run for at least 3 minutes while dehumidifying.

8 DO NOT start the dehumidier immediately after shutting down, allow 3 minutes before restarting.

5.2. TIMER FUNCTION

5.2.1. To set Timer for power ON mode, with the unit in power OFF state, press the Timer button (g.3.6). The Timer ON LED (g.3.1) will

icker and the current set time will be displayed. Use the Increase/ Decrease buttons (g.1.10, g.1.11) to set the required value to

between 0 and 24 hours. After 10 seconds the selected value is set and the Timer ON led will icker.

5.2.2. To set the Timer for power OFF mode, with the unit in power ON state, press the Timer button (g.3.6). The Timer OFF LED (g.3.1)

will icker and the current set time will be displayed. Use the Increase/ Decrease buttons (g.3.10, g.3.11) to set the required value to

between 0 and 24 hours. After 10 seconds the selected value is set and the Timer OFF led will icker.

5.3. DEFROSTING

5.3.1. The defrosting device works automatically at an interval of approximately every 30 minutes for a duration of approximately 5 minutes

when the coil temperature is tested to be <= minus 1oC.

The dehumidifying function will stop during the defrosting operation. DO NOT disconnect the plug or turn off the unit during the

defrosting operation. The defrosting led light (fig.3.7) will light up.

NOTE: This dehumidifier does not have a cooling function, it produces heat during the operation and room temperature will rise

by 1°C to 4°C. The temperature gets higher while it is operated in a closet, or similar. Furthermore, room temperature will rise because

doors and windows are closed and heat is produced from other appliances in the room and from sun radiation.

5.4. EMPTYING THE WATER COLLECTION TANK

5.4.1. During the dehumidifying operation, water is collected in the water collection tank. When the tank is full of water, the dehumidifier stops

operating automatically and the warning buzzer beeps twice. The unit will not restart until water collection tank has been emptied.

5.4.2. Open the door and remove water collection tank from the dehumidifier by pulling it gently outwards by holding the sides of the tank.

5.4.3. Hold the tank by the handle and carry it carefully to an emptying point.

5.4.4. Remove the plug at the bottom of the tank and slowly empty the water out of the tank.

5.4.5. Replace the drain plug and refit the tank in the dehumidifier, making sure it is properly back in place as the unit will not restart if it is

not fitted correctly.

ITEM OPERATION

1 Timer Indicator

2 Temperature Indicator

3 Dehumidication Indicator

4 Humidity Indicator

5ON/OFF Control

6Time Set Control

7 Defrosting Indicator

8 Air Speed Indicator

9 Water Full Indicator

10 Increase Control

11 Decrease Control

123 4 5 6

78910 11

BUTTON OPERATION INSTRUCTIONS

ON/OFF (g.1.5) Changes between Switch on and Switch o.

+ (fig.1.10)

Adjust dierent set values in dierent states;

1. Increases the humidity value set (RH10% to 95%)

2. Increases the timing (hour) set (00 to 24)

- (fig.1.11)

Adjust dierent set values in dierent states;

1. Decreases the humidity value set (RH10% to 95%)

2. Decreases the timing(hour) set (00 to 24)

Timer (g.1.6) Short press the button to launch a cycle to o.

Set on/o Timer and Exit

g.3

SDH30.V3 Issue 2 (2) 16/05/22

Original Language Version

5.5. CONTINUOUS DRAINING

5.5.1. If there is a place suitable for draining, continuous draining can be carried out. The continuous operation enables the dehumidfying

operation to continue uninterrupted. See Section 4.6.

6. MAINTENANCE

6.1. CLEANING THE AIR FILTER

6.1.1. The dehumidifying capacity is lowered when the air cleaning filter becomes clogged.

6.1.2. Open the front door of the unit.

6.1.3. Lift up the filter element from the bottom and lift out of the holder.

6.1.4. To dislodge the dust from the filter, use a vacuum cleaner or tap it lightly.

6.1.5. If the filter is very dirty, wash it carefully in water with a neutral detergent, then rinse well with clean water and leave until dry.

6.1.6. To refit the air filter locate the top of the element into the locating bracket at the top of the door and then locate the lower section into

the lower bracket.

6.1.7. Close the door of the dehumidifier.

6.2. STORAGE

6.2.1. Unplug the unit, bundle the power cord, and hang the bundled cord at the back of the unit.

6.2.2. Remove the water collection tank and empty the water out of it. Remove the tank cover and wash the inside of the tank with clean

water. The tank may be scratched if it is scrubbed strongly with a brush. DO NOT remove the float lever from the tank. Wipe off the

water on the outside of the tank with a cloth. Refit the tank cover onto the tank and replace the tank in position.

6.2.3. Clean the air filter (see 6.1).

6.2.4. When the unit is to be stored for a long time, wipe the dehumidifier over with a dry soft cloth. To remove dirt, wipe over with a very

slightly dampened cloth (never use a wet cloth for cleaning the controls). To avoid deformation or cracking, do not use benzine,

thinner or liquid cleaners.

6.2.5. When storing, place in a safe, dry, childproof location. Stand the unit upright and avoid exposure to direct sunlight.

7. TROUBLE SHOOTING

Faults Cause Analysis Solutions

Fails to turn on

Shown as no power

No power to the wall socket. Check the power supply.

Check the plug plugged in

properly.

Plug the power supply in the socket.

Check the fuse is not blown. Replace the fuse.

Power Transformer is broken. Replace the transformer.

Shown as power on

Environmental humidity lower

than the set value.

Set again according to the demand.

If the water tank is installed

correctly.

Place the water tank in right position.

If the entire machine is defrosting. Wait for the completion of defrosting cycle.

Unfavourable

dehumidifying eect

If the air inlet/outlet is obstructed. Remove the obstacle.

If the door and window are open. Close the door and window.

If the indoor temperature is too low. Don’t run the dehumidier.

Heavy noise If the ground is rm and at. Resettle the dehumidier.

Dehumidier is stood precariously. Resettle the dehumidier.

Water leakage Dehumidier stood on an incline. Move dehumidier to a level surface.

Drain pipe/outlet obstructed. Dismantle the front plate to eliminate blockages.

E1 Coil sensor fault Turn to timing for defrosting, to cancel system fault

function.

E2/E3 Fault of humidity & temperature sensor. Replace the humidity & temperature sensor.

EE Refrigerant leakage. Attempt shut down and restart, if no change seek help

from professionals if the “EE” signal remains.

SDH30.V3 Issue 2 (2) 16/05/22

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to

a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely

unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids

according to local regulations.

WEEE REGULATIONS

Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment

(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid

waste authority for recycling information.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior

notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call

our technical team on technical@sealey.co.uk or 01284 757505.

Important: No Liability is accepted for incorrect use of this product.

Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

Original Language Version