2. Miele
  3. TX0917
TX0917

Miele TX0917 Installation guide

  • Hello! I've reviewed the installation instructions for the Miele Dialog oven. This document covers critical steps for proper and safe installation, including building-in dimensions, ventilation requirements, and electrical connections. I'm ready to answer your questions about the appliance and the information found in the document.
  • What is the recommended length of the mains connection cable?
    What is the minimum area for the ventilation cut-out?
    What should be taken into account when connecting electricity?
11527500-06
Installation
*INSTALLATION*
Building-in dimensions
Dimensions are given in mm.
Installation in a tall or base unit
If the Dialog oven is to be installed in a base unit underneath a cooktop, please
also observe the installation instructions for the cooktop as well as the building-in
height required for the cooktop.
11527500-06
Installation
*INSTALLATION*
Side view
11527500-06
Installation
*INSTALLATION*
Connections and ventilation
aFront view
bMains connection cable, length=2000mm
cNo connections permitted in this area
dVentilation cut-out, min. 150cm²
11527500-06
Installation
*INSTALLATION*
Installing the Dialog oven
For safety reasons, the Dialog oven
must only be used after it has been
built in.
The Dialog oven requires a sufficient
supply of cool air for efficient
operation. The required supply of
cool air must not be excessively
heated by other heat sources (e.g.
solid fuel stoves).
The following must be observed
when installing the appliance:
Do not fit a back panel in the housing
unit.
Ensure that the interim shelf that the
Dialog oven sits on does not touch
the wall.
Do not fit heat insulation strips to the
side walls of the housing unit.
Before starting installation work,
ensure that there is no power to the
socket.
Connect the Dialog oven to the
electrical supply.
Lifting the Dialog oven by the door
handle could cause damage to the
door.
Use the handle cut-outs on the side
of the casing to lift the appliance.
Push the Dialog oven into the housing
unit and align it.
Open the door.
Pull the water intake pipe forwards
(located below the control panel on
the left).
Secure the Dialog oven to the side
walls of the housing unit using the
screws supplied.
11527500-06
Installation
*INSTALLATION*
Electrical connection
Danger of injury!
Installation, repairs and other work
by unqualified persons could be
dangerous. Miele cannot be held
liable for unauthorised work.
Ensure power is not supplied to the
appliance until after installation or
repair work has been carried out. All
electrical work must be undertaken
by a suitably qualified and
competent person in strict
accordance with current national and
local safety and building code
regulations.
The Dialog oven is supplied with a
mains connection cable and plug, ready
for connection to a 50Hz, 220–240V
supply.
Connection of this appliance must
comply with national and local safety
regulations.
Connection to a switched socket is
recommended as this provides easier
access in the case of a service call.
For extra safety, it is advisable to
protect the appliance with a suitable
residual current device (RCD) with a trip
current of 30mA.
If the switch is not accessible after
installation, an additional means of
disconnection must be provided for all
poles. The means of disconnection
must be incorporated in the fixed wiring
in accordance with the wiring rules.
When switched off there must be an all-
pole contact gap of 3mm in the isolator
switch (including switch, circuit
breakers and relays).
Voltage, rated load and fuse rating
are given on the data plate situated at
the front of the oven compartment.
Please ensure these match the
household electricity supply.
If the connection cable is damaged, it
must be replaced by a Miele approved
service technician in order to avoid a
hazard.
WARNING - THIS APPLIANCE
MUST BE EARTHED
Temporary or permanent operation with
a self-sufficient or non-mains
synchronous energy supply system
(e.g. isolated networks, back-up
systems) is possible. A requirement for
the operation is that the energy supply
system complies with all current local
and national requirements that apply to
stand-alone, solar and/or battery
systems.
The protective measures provided in
the domestic installation and in this
Miele product must also be assured in
their function and operation in isolated
operation or in non-mains synchronous
operation, or replaced with equivalent
measures in the installation.
/