Curtis 13470 User manual

Curtis
Brand
Curtis
Model
13470
Category
Wall & ceiling mounts accessories
Type
User manual

The Curtis 13470 is a weight-carrying and weight-distributing trailer hitch with a gross trailer weight capacity of 3,500 lbs. and a tongue weight capacity of 350 lbs. It can be used for towing a variety of trailers, such as utility trailers, boat trailers, and small campers. The hitch is easy to install and requires no drilling. It comes with all the necessary hardware and instructions for a quick and easy installation.

The Curtis 13470 is a weight-carrying and weight-distributing trailer hitch with a gross trailer weight capacity of 3,500 lbs. and a tongue weight capacity of 350 lbs. It can be used for towing a variety of trailers, such as utility trailers, boat trailers, and small campers. The hitch is easy to install and requires no drilling. It comes with all the necessary hardware and instructions for a quick and easy installation.

CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 • 13470-INS-RA • 11/30/2020 • ECN7750 • PAGE 1
Product Registration and Warranty
CURT stands behind our products with industry-leading warranties. To get copies of the product
warranties, register your purchase or provide feedback, visit: warranty.curtgroup.com/surveys
Weight Carrying Capacity
Gross trailer weight (GTW) 3,500 lbs.
Tongue weight (TW) 350 lbs.
Weight Distribution Capacity
Weight distribution (WD) 5,000 lbs.
WD tongue weight (WDTW) 500 lbs.
INSTALLATION MANUAL 13470
Tools Required
Ratchet Torque wrench
Socket, 19mm Flathead screwdriver
Socket, 10mm Aviation shears
Socket extension, 6" --
* For a tools reference guide visit
curtmfg.com/trailer-hitch-installation
Level of Difficulty
Easy
Installation difficulty levels are based on time
and effort involved and may vary depending on
the installer level of expertise, condition of the
vehicle and proper tools and equipment.
WARNING
Never exceed the vehicle manufacturer's recommended towing capacity.
SAFETY INSTRUCTIONS
Safety glasses should be worn at all times while installing this product.
NOTICE
Visit www.curtmfg.com for a full-color copy of this
instruction manual, as well as helpful videos, guides and much more!
Before you begin installation, read all instructions thoroughly.
Proper tools will improve the quality of installation and reduce the time required.
This installation requires:
• Trimming of the underbody panel
• NO DRILLING REQUIRED
Periodic inspection of the trailer hitch should be performed to ensure all
mounting hardware remains tight and structural components are secure.
To help prevent damage to the product or vehicle, refer to the specified
torque specifications when securing hardware during the installation process.
Parts List
Item Qty Description
1 6 Hex bolt,
M12-1.25 x 40mm, CL 10.9
2 6 Conical-toothed washer, 1/2"
Product Photo
CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 • 13470-INS-RA • 12/03/2020 • ECN7750 • PAGE 2
Passenger-side
frame rail
Driver-side
frame rail
Existing
weldnuts
(both sides)
ASSEMBLY
VEHICLE FRAME
CONICAL TOOTHED WASHER ORIENTATION
HITCH SIDE PLATE
HEX BOLT
CONICAL TOOTHED WASHER
To remove debris from weldnuts
in frame, spary lubricant or
compressed air into the hole.
For heavy debris, use a wire brush.
Take care not to damage threads.
WELDNUT CLEANING
FRONT
REAR
Parts List
Item Qty Description
1 6 Hex bolt,
M12-1.25 x 40mm, CL 10.9
2 6 Conical-toothed washer, 1/2"
2
1
CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 • 13470-INS-RA • 12/03/2020 • ECN7750 • PAGE 3
Step 1
Remove the underbody panel from the
passenger side of the vehicle by removing
three push fasteners and three screws
using a 10mm socket.
Step 4
Torque all M12 bolts to 86 lb-ft.
Step 2
Remove the three hole plugs and
clean the weldnuts in each frame rail.
Step 3
Raise the trailer hitch into position and
secure with three M12 hex bolts (#1) and
conical-toothed washers (#2) on each side.
CURTMFG.COM • PRODUCT SUPPORT: 877.287.8634 • 13470-INS-RA • 12/03/2020 • ECN7750 • PAGE 4
TOWING BASICS & SAFETY INFORMATION
For information on safely towing your trailer, visit curtmfg.com/understanding-towing.
Step 5
Trim the underbody panel using the groves
on the panel as guides. A trim diagram is
provided for reference.
Reinstall the panel using the factory hardware. 7-1/4"
3"
Final Installed Image
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Curtis 13470 User manual

Curtis
Brand
Curtis
Model
13470
Category
Wall & ceiling mounts accessories
Type
User manual

The Curtis 13470 is a weight-carrying and weight-distributing trailer hitch with a gross trailer weight capacity of 3,500 lbs. and a tongue weight capacity of 350 lbs. It can be used for towing a variety of trailers, such as utility trailers, boat trailers, and small campers. The hitch is easy to install and requires no drilling. It comes with all the necessary hardware and instructions for a quick and easy installation.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents