Johnson Hardware VH-40 User manual

Type
User manual
4/29/03
Manual V-16, V-24, VH-24, V-40 & VH-40 1 – Section I
JOHNSON VERTICAL BAND SAWS
INSTRUCTION MANUAL AND PARTS LIST
SECTION I – Manual
FOR MODELS
E-16
V-16
V-24
VH-24
V-40
VH-40
N MANUAL AND PARTS LIST
MODEL: ________________________________________
SERIAL NUMBER: ________________________________
DATE PURCHASED: ______________________________
DAKE Division of JSJ
724 Robbins Road
Grand Haven, Michigan 49417
616.842.7110 Phone 800-937-3253
616.842.0859 Fax 800-846-3253
Web: www.dakecorp.com
technicalsupport@dakecorp.com
4/29/03
Manual V-16, V-24, VH-24, V-40 & VH-40 2 – Section I
If machine is to be operated
At 440 volt 3 phase power, please
read the following warning.
FOREWORD
These instructions cover the installation and operation of vertical band saws. Attention
to maintenance and service will afford many years of trouble free operation. We suggest that
these instructions be retained by the department or individual responsible for the machine and
kept in a readily accessible location for reference purposes.
WARNING!
This machine must
be wired by a qualified
electrician. Do not
connect 440-volt power directly
to this machine. The use of the step down
transformer supplied with this machine must be
used. Failure to do so may affect warranty, if
damage occurs from improper wiring.
4/29/03
Manual V-16, V-24, VH-24, V-40 & VH-40 3 – Section I
SECTION I - TABLE OF CONTENTS
Specifications ....................................................................................... 4
Machine Features ................................................................................ 5-6
Unloading ............................................................................................. 7
Installation ............................................................................................ 7
Electrical .............................................................................................. 7
Filling Speed Regulator ………………………………………………….. 8
Machine Operation .............................................................................. 8
Wheel Alignment ................................................................................. 9
Blade Installation ................................................................................. 9
Blade Tensioning ................................................................................ 10
Blade Guides / Adjustment .................................................................. 10-14
Band Speed Selection ......................................................................... 14
Saw Blade Selection……………………………………………………… 15-16
Blade Break-in…………………………………………………………….. 15
Speeds & Feeds ................................................................................. 16-20
Rate Reduction Matrix For Hard Material ........................................... 20
Hydraulic Feed Table ……………………………………………………. 21
Welding Instructions ............................................................................ 21
Blade Preparation For Welding ........................................................... 21-22
Clamping / Welding / Annealing ......................................................... 22-23
Re-Finishing the Weld (Grinding) ....................................................... 23
Welder Layout & Maintenance ........................................................... 23
Poor Welds & Trouble Shooting ......................................................... 23-24
Machine Maintenance ........................................................................ 24
Use Of Standard Accessories ..……………........................................ 24-25
4/29/03
Manual V-16, V-24, VH-24, V-40 & VH-40 4 – Section I
SPECIFICATIONS
Model Number: V-16 V-24/VH-24 V-40/VH-40
Capacity:
Throat Inches 16 23-1/2 41
Work Height Inches 11 12-1/2 12-1/2
Table:
Work Table Inches 23-1/2 x 23-1/2 26-3/8 x 26-3/8 26-3/8 x 26-3/8
Auxiliary Inches -- 9 x 22-3/8 15-1/2 x 21-1/2
Height from Floor Inches 38 42 41
Travel-Manual or Hydraulic Inches -- 10 10
Tilt-Left Degree 10 10 10
Tilt-Right Degree 30 30 30
Table Weight Capacity Lbs. 850 850 850
Blade:
Width Minimum Inches 1/8 1/8 1/8
Width Maximum Inches 5/8 1 3/4
Length Minimum/Maximum Inches 128/133 178/187 134/140 (2
wheels)
Length Minimum/Maximum Inches -- -- 186/189 (3
wheels)
Wheel Diameter Inches 16-1/2 24-1/2 16-1/2
Band Speed:
Low Range FPM 60 to 590 50 to 425 50 to 425
High Range FPM -- 425 to 4250 425 to 4250
Drive Motor HP 1 2.2 2.2
Welder Capacity:
Inches 1/8 – 5/8 1/8 – 1 1/8 – 1
VH models equipped
with hydraulic table
Hydraulic Motor:
HP -- 1/3 1/3
Height of Machine:
Inches 72 90 78
Floor Space:
Inches 38 x 25 60 x 60 72 x 60
Shipping Weight:
Manual Table Lbs. 1000 2025 2025
Hydraulic Table Lbs. -- 2225 2395
4/29/03
Manual V-16, V-24, VH-24, V-40 & VH-40 5 – Section I
4/29/03
Manual V-16, V-24, VH-24, V-40 & VH-40 6 – Section I
4/29/03
Manual V-16, V-24, VH-24, V-40 & VH-40 7 – Section I
MACHINE UNPACKING AND INSTALLATION
UNLOADING:
Remove the shrink-wrap covering the machine, carefully as not to damage painted
surfaces, electrical or hydraulic parts. Carefully inspect the machine for physical damage. If
damage is noted, notify the truck line at once. They may require inspection, and that a claim be
filed. Check that all standard accessories are with the machine. Some accessories may be boxed or
placed behind access doors or chip drawer. (See figure 2 & 3) The band saws are provided with lifting
eyes that screw into the top of the machine. These lifting eyes may be located in any of the
compartments shown by arrows in figure 1 & 2 above. Particular care should be taken in selecting
areas of the machine for handling, as electrical components and adjustment knobs can be marked up
or damaged. WARNING: Machine table may NOT
be used as a lifting point. Damage to the saw
and alignment problems could result. Remove the mounting bolt nuts from the machine. Using the
lifting eyes, remove the machine from the skid and put in place. (See figure 1)
INSTALLATION:
Location of the machine should take into consideration the ability to traverse
large work pieces. The machine is provided with holes in the base to anchor the unit to the floor.
Shims should be used to properly level the unit. The saw is shipped with an anti-rust protective coating
on machined metal surfaces. Surfaces should be cleaned with the appropriate solvent and then coated
with a light film of oil.
ELECTRICAL:
The machine is wired to be operated with an input voltage of 230, 3 phase, 60 htz
(+/- 10%) or with a Dake external step down transformer from 460v to 230v. If any adjustments or
changes are needed a qualified electrician should perform them. See detailed information as provided
in a circuit diagram #80587.
4/29/03
Manual V-16, V-24, VH-24, V-40 & VH-40 8 – Section I
FILLING THE SPEED REGULATOR
1. Turn the saw on.
2. Screw the handwheel in.
3. Turn the saw off once handwheel is in.
4. Remove the mounting screws (item 6).
5. Remove the plug from the cylinder (Item 3).
6. Turn screw out.
7. Add oil (Lightweight hydraulic oil) slowly while turning the wheel out.
8. When it is completely full, replace the plug (Item 3).
9. Re-mount the cylinder to the saw body.
10. Turn on the saw and adjust to the desired speed.
11. When saw is at maximum RPM, re-adjust the lock nuts on Item 8
MACHINE OPERATION
Prior to performing any cutting with the machine, it is recommended that the personal become
familiar with the various controls and accessories.
PRECAUTIONS
No loose clothing.
Eye protection should be worn.
All guards must be in position.
Table is secured in place and locked. Table load capacity should be noted and not exceeded.
Extra supports may be required for large or cumbersome components.
Irregular shapes and small objects should be secured by means of a clamp or suitable fixture.
Machine and surrounding should be kept free of tools, scrap and foreign objects.
Machine should be locked out before making any adjustments.
Care in uncoiling, and coiling and installation of blades should be observed. Gloves recommended.
Storage of blades in an area near the machine will allow operating personal, to use the proper
blade for each operation.
Machine is furnished with electrical door interlocks. These interlocks should periodically be checked
for proper operation.
4/29/03
Manual V-16, V-24, VH-24, V-40 & VH-40 9 – Section I
WHEEL ALIGNMENT
V-16 & V / VH-24
Note: This alignment is factory set, but may need adjustment when replacing blade.
Two wheel machines have a bottom wheel that drives the saw blade and a top idle wheel that is
adjustable to facilitate blade tracking. The edges of the wheels are fitted with a composite material to
accommodate the tooth set.
The idle wheel may be adjusted by loosening the knurled locking collar and turning the black knob in
the center of the wheel. Turning the knob in a clockwise
manner runs the blade toward the back edge
of the band wheel. A counter clockwise
movement will move the blade toward the front edge of the
band wheel.
Correct tracking takes place when the blade runs approximately in the center of the wheel.
NOTE: The main casting with adjusting screws have been preset at the factory during assembly
utilizing special fixtures. No adjustment should be attempted.
V-40 / VH-40
Machines with two idle wheels in addition to the drive wheel possess tracking control on each wheel.
The top band wheel is set at the factory and no future adjustment should be necessary. *All
adjustments should be performed utilizing the third band wheel. If difficulty is encountered in tracking,
the top wheel may be reset as if the machine were to be used in the two wheel mode.
NOTE: With the V / VH-40 machines, it is possible to
have the blade appear to be tracking properly but in
actuality the two band wheels can be adjusted so they
form an intersecting planes, rather than a common plane
or parallel plane. This will result in excessive wear on
the crown on the band wheel by the blade teeth, and
severe cases, the composite material will shred or
actually come loose from the band wheel.
*If the blade does not track properly against the back up
guide bearing, there is a small amount of lateral
adjustment in the top wheel. (See figure 5) Loosen the
set screws and slide the yoke to make the blade line up
properly with the backup guide bearing.
BLADE INSTALLATION
Blade selection is based on the many factors and complexity of the work to be cut.
The blade placed on the band wheels with teeth facing toward the operator and down toward the top of
the worktable. Tension the blade to remove slack. Rotate the wheels by hand to ensure tracking is
correct, and blade will not “pop” off when machine is started. If tracking is incorrect, adjust before
starting machine.
4/29/03
Manual V-16, V-24, VH-24, V-40 & VH-40 10 – Section I
BLADE TENSIONING
The blade indicator is located inside the upper wheel compartment, on the lower left side of the idle
wheel. (See machine features graphic) The indicator has an arrow mounted on the horizontal plane,
with a corresponding scale for blade tensioning. The scale has two legends, one reads inches from 0 -
1”, the second reads mm 0 - 25 mm. This allows tensioning either standard or metric blade widths.
With out tension on the blade, the indicator should read zero. As tension is applied to the blade the
needle will move accordingly, and should be tightened until the correct blade width is indicated on this
gauge. Example: Installing a 1/2” blade on the machine, tighten the handwheel until the indicator’s
arrow is pointing to the 1/2” mark on the scale. Before starting the machine check the blades tracking
by hand as described in an earlier section.
This indicator has been calibrated at the factory. If recalibration is ever needed follow the steps below.
Using a blade tension gauge, (many times the
company that you purchase blades from can furnish
you with this gauge) tension the blade to the proper
PSI. The PSI will very from blade types (carbon, Bi-
metal) and blade widths. This information can be
obtained from your blade supplier. When proper
tension is achieved, loosen the setscrew in the collar
on the tensioning wheel shaft. (See figure 6) Adjust
this collar up or down on the shaft until the arrow is
pointing to the corresponding blade width. on the
indicator. Tighten setscrew.
Note: It is better to over tension the blade than to
run it under tensioned.
BLADE GUIDES
Your machine has come equipped with a set of interchangeable “V” type blade guides. A set of
guides consist of two each left hand and two each right hand guide inserts. The standard
guides furnished are 10 / 12 mm guides. Other sizes are optional, and can be purchased
separately, or as a five piece set. The five-piece set includes 3 / 4 mm (1/8 - 1/4”) 6 / 8 mm
(5/16 - 3/8”) 10 / 12 mm (standard set 1/2 - 5/8”) 16 / 20 mm (3/4”) and 25 / 32 mm (1”) The
blade width will dictate the size blade guide to be used.
Note: Never use blades larger than the rated capacity of the machine. Never use blades
narrower than guide insert. Damage will occur to guide insert and blade. Blade insert must
correspond with blade width.
4/29/03
Manual V-16, V-24, VH-24, V-40 & VH-40 11 – Section I
An analysis of the work to be performed should be made and the proper
blade selected. The blade should always be inspected before installing
on the machine. Things to look for should be the smoothness on the
sides and back edge of the weld, look for any missing teeth, or
impacted chips. The blade guides may now be selected and inserted
into both the upper and lower guide holders. Proper adjustment of these
guides takes place when they form a complete “V” shape (see graphic
below) and support the blade equally on each side. A couple of
thousands on each side of the blade will provide the running clearance
and support for contour sawing.
Note: Blade guides should be cleaned of chips each blade
change or more frequently if required.
BLADE GUIDES
The back end roller that supports the back of the blade on each guide holder contains a hardened cap
over a set of ball bearings. This should be checked periodically for free movement so it is allowed to
rotate freely as the back of the blade comes in contact with the face of this roller. Noticeable friction in
this assembly indicates it should be replaced. This can be done by removing the right hand guide
insert, moving the left hand guide up away from the bearing face. Loosen the setscrew on the bottom
of the guide holder and sliding the old bearing and shaft out and a new one in. Tighten the setscrew
and re-adjust the guides. See graphic below.
The “V” type solid blade guides and holder assemblies as furnished standard with the machine are
recommended for the majority of cutting applications. This is true for the cutting of materials at blade
speeds in the low range.
If the machine is operated in the high range, it should be operated with the high-speed roller guides,
supplied with this machine, installed.
NOTE: If machine is operated in excess of above, abnormal blade wear and breakage may
occur, due to the increased heat developed with the standard solid guides.
4/29/03
Manual V-16, V-24, VH-24, V-40 & VH-40 12 – Section I
HIGH SPEED ROLLER GUIDES
Applications and Advantages:
Friction and abrasive cutting, filing operations, aluminum and woodcutting.
These guides eliminate having to change inserts when changing to blades of different widths.
Requirements for Installation:
These roller guides must be installed using a new
1/2” blade width band for proper alignment.
The 1/2” band should be tracked within the approximate center line of the band wheels.
Note: Be certain band wheels are clean are free of any foreign material build up before
proceeding.
Tools / Hardware Required:
Drill - 7/16”
Drill and tap for ¼” 20 set screw
¼” 20 set screw 1/4 - 3/8” long
Upper Guide Installation:
1: Remove the existing guide holder assembly (part A)
via the 2 countersunk socket head cap screws located
on the backside of the moveable guide arm post. (Part
B) Store the original guide holder assembly for future
use. Remove the lower (red painted, part C) hold
down foot located at the bottom of the movable guide
arm post. (See graphic below)
2: With a 7/16” drill the bottom guide-mounting hole
out. Drill from the front of the guidepost, to a depth of
approx. 1”. The hole should be just deep enough to
stop short of breaking through the countersunk portion
of the hole.
3: Drill and tap a hole for a ¼” 20 set screw approx. ½ - ¾” back from the front edge of the guidepost.
This hole must be centered (intersect) with the 7/16” hole. As shown above.
4/29/03
Manual V-16, V-24, VH-24, V-40 & VH-40 13 – Section I
4: Insert the mounting stud (B) into the guide casting (A). Keep the stud
flush with the front of the casting. Keeping the mounting stud flat area
on the bottom, tighten securely the set screw (C) on the bottom of the
casting.
5: Insert this stud and guide assembly into the 7/16” hole in the guidepost. Make sure upper roller guide
is plumb with the guidepost. Lightly tighten set screw you installed in the guidepost.
Lower Guide Installation:
6: Remove lower blade guide. Replace this guide with the high
speed guide containing the
mounting bracket with slotted hole, reusing existing nuts /
bolts.
Position assembly upward along the slotted bracket, so that
the guide body casting has enough clearance to allow the
work table to be tilted for angle cutting. Tighten the socket
head cap screw or nut.
Note: Make certain that if a socket head cap screw is
used, it does not bottom out into the main saw casting
item 1. Shorten the cap screw if necessary
7: Alignment of Upper / Lower Guides:
With blade properly tensioned and tracked, position the
back-up roller by loosening the set
screw (A) on the front of the guide casting, and move the
knurled knob left to right until blade is in alignment with
the groove in the bearing. Rotate the knurled knob until
you have approx. 1/16” clearance from the back of the
blade to the front edge of the back-up roller. Tighten set
screw (A).
The two roller bearings below the back up bearing can
be adjusted in and out, left and right. Loosen the set screws that retain the bearing stems into the
casting. Using the single bearing assembly, position these bearings approx. 1/16” behind the deepest
gullet of the blade.
The single bearing assembly along with the adjustably of the upper guide roller will service blades from
¼” to ¾” The double roller set is used only when blade of ½” to 1” are used. Note: The adjustments
are the same for both single and double bearing assemblies.
Rotate eccentric bearing stems until both blade and the back up bearing groove are parallel with each
other. Set screws should be just snug up until actual alignment is confirmed.
4/29/03
Manual V-16, V-24, VH-24, V-40 & VH-40 14 – Section I
Repeat this process for the lower guide assembly.
Note: Upper guide stud may be adjusted in or out in the guide post to allow proper clearance for
blade, and for alignment with lower guide.
Align backup bearing as previously described for upper guide. Tighten both set screws when alignment
is confirmed.
Re-adjust side rollers. (Graphic in previous column) Set the side clearance distance between rollers
and saw blade, leaving about a .004 gap.
Note: If the adjustment setting for side clearance
between roller and blade is not enough, the side
rollers will cause the blade to miss-track or be
pushed outward from the guide rollers.
Note: If blade alignment from band wheel to
roller guides is necessary, do so by rotating
eccentric shafts on the roller guides. Then
lock them in place with the set screws.
After all adjustments have been made, tighten
all components tight.
BAND SPEED SELECTION
The saw blade is driven by a single speed transmission on the 16” machine and dual speed
transmissions on the 24” and 40” machines. The shifting lever on the larger models has three positions.
(Figure 1) The center being the neutral position, for set up. With the machine off, move the shift lever to
the left for low speed range (50-500 FPM) and to the right for the high speed range. (500-5000 FPM)
To shift the machine the shift lever handle must be pulled outward and then shifted left or right. (Figure
2)
WARNING: NEVER SHIFT WHILE THE MOTOR IS RUNNING. THIS WILL CAUSE EXTENSIVE
DAMAGE TO THE DRIVE TRAIN.
4/29/03
Manual V-16, V-24, VH-24, V-40 & VH-40 15 – Section I
Note: Occasionally the drive wheel may have to
be jogged by hand to engage the transmission
lever.
The variable speed is achieved through the use of a
variable regulator. (Figure 3) This is turned clockwise
or counter clockwise to obtain an increase or
decrease in blade speed, in either range. Adjust until
desired speed is reached as read on the blade
speed gauge. (Figure 4)
WARNING: DO NOT ADJUST THE VARIABLE SPEED
CONTROL (FIGURE 3) SPEED UNLESS THE MACHINE IS IN
OPERATION! FAILURE TO DO SO WILL CAUSE SEALS TO
FAIL, AND RENDER THE UNIT INOPERABLE.
SAW BLADE SELECTION
There are numerous types of saw blades available depending upon the application. Tooth pitch, form,
tooth set, and blade composite make up all contribute to the desired cut. Blade speeds and feed are
also a factors. The complexity of the subject cannot be properly detailed in this manual, and it is
suggested that you contact your local blade supplier for more detailed information and
recommendations for the application.
Below is a chart that can be used as a guide line for blade selection and a percentage chart for
determining the speeds and feeds for material after determining the Rockwell hardness.
The chart below shows material shape and sizes of square solid, round solid, and tubing, channel, and
angle. The size range from 0” - 12” is diameter; the column under the shapes gives recommendation of
a vari-tooth blade. Example: 4” round solid, will require a 3/4 pitch blade.
Note: For structurals and tubing, determine the average width of cut.
Blades must be broke in properly, for longest life and best cut finish. Break in cutting should be
done at 1/3-1/2 normal cutting rate, for the 50-100 square inches.
NOTE: Below are the three most commonly used types of blades. The Bi-Metal blade is the most durable, for standard types of cutting
applications. The teeth are made of high speed steel and welded to a backing material. The cutting edge contains 8% cobolt with a Rc of 64
to 68. (These blades are more difficult to weld than standard carbon.) The carbon blade is the least expensive with reduced blade life. The
back of the blade is made of hardened material with a Rc of 31 to 37 and tooth hardness of 64 to 66. The carbide tipped blade has carbide
inserts welded to the blade teeth with a Ra rating of 92
4/29/03
Manual V-16, V-24, VH-24, V-40 & VH-40 16 – Section I
SAW BLADE SELECTION
MATERIAL SHAPE MATERIAL SHAPE MATERIAL SHAPE
MATERIAL IN
INCHES TOOTH SELECTION TOOTH SELECTION TOOTH SELECTION
0 14 / 18 14 / 18 14 / 18
.1 14 / 18 14 / 18 14 / 18
.2 14 / 18 14 / 18 14 / 18
.3 10 / 14 14 / 18 10 / 14
.4 8 / 12 10 / 14 8 / 12
.5 8 / 12 8 / 12 6 / 10
.6 6 / 10 8 / 12 5 / 8
.7 6 / 10 6 / 10 5 / 8
.8 5 / 8 6 / 10 5 / 8
.9 5 / 8 5 / 8 5 / 8
1 5 / 8 5 / 8 4 / 6
1 1/4 4 / 6 5 / 8 4 / 6
1 1/2 4 / 6 4 / 6 4 / 6
1 3/4 4 / 6 4 / 6 4 / 6
2 4 / 6 4 / 6 3 / 4
2 1/4 4 / 6 4 / 6 3 / 4
2 1/2 3 / 4 4 / 6 3 / 4
2 3/4 3 / 4 4 / 6 3 / 4
3 3 / 4 3 / 4 3 / 4
3 1/4 3 / 4 3 / 4 3 / 4
3 1/2 3 / 4 3 / 4 3 / 4
3 3/4 3 / 4 3 / 4 2 / 3
4 3 / 4 3 / 4 2 / 3
5 2 / 3 3 / 4 2 / 3
6 2 / 3 3 / 4 2 / 3
7 2 / 3 2 / 3 1.4 / 2.5
8 1.4 / 2.5 2 / 3 1.4 / 2.5
9 1.4 / 2.5 2 / 3 1.4 / 2.5
10 1.4 / 2.5 1.4 / 2.5 1.4 / 2.5
11 1.4 / 2.5 1.4 / 2.5 1.4 / 2.5
12 1.4 / 2.5 1.4 / 2.5 1.4 / 2.5
SPEEDS AND FEEDS
As important as proper blade selection, is proper feeds and speeds for the different materials to be cut.
It is impossible to determine absolute rates for each material and machine, below is a chart that will
give you staring points for most applications; keeping in mind these are only approximations.
The left hand column, labeled Material tells you the family, the column Alloy lists the types that are
within that family of material. The top six columns give material dimensions. Below these column are
listed the recommended FPM and SIPM for that material type. Example: Carbon steel with a alloy make
up classified as 1030, with a diameter of 4” will be cut at 329 FPM and SIPM of 14, shown as fpm 329
sipm 14.
4/29/03
Manual V-16, V-24, VH-24, V-40 & VH-40 17 – Section I
MATERIAL ALLOY 1/2" 1" 2" 4" 7" 12"
1100,2011,2017,2024 fpm 568 sipm 7 fpm 577 sipm 11 fpm 536 sipm 16 fpm 498 sipm 21 fpm 451sipm 23 fpm 389 sipm 24
ALUMINUM ALLOY 3003,5052,5086,6061 fpm 568 sipm 7 fpm 577 sipm 11 fpm 536 sipm 16 fpm 498 sipm 21 fpm 451sipm 23 fpm 389 sipm 24
6063,6101,6262,7075 fpm 568 sipm 7 fpm 577 sipm 11 fpm 536 sipm 16 fpm 498 sipm 21 fpm 451sipm 23 fpm 389 sipm 24
356,360 fpm 511 sipm 7 fpm 501 sipm 10 fpm 482 sipm 14 fpm 448 sipm 19 fpm 406 sipm 21 fpm350 sipm 22
353 fpm 454 sipm 6 fpm 445 sipm 8 fpm 429 sipm 12 fpm 399 sipm 17 fpm 361 sipm 19 fpm311 sipm 19
1452,187 fpm 426 sipm 6 fpm 418 sipm 8 fpm 402 sipm 12 fpm 374 sipm 16 fpm 338 sipm 18 fpm 292 sipm 18
380,544 fpm 397 sipm 5 fpm 390 sipm 7 fpm 375 sipm 11 fpm349 sipm 15 fpm 316 sipm 16 fpm 272 sipm 17
173,932 fpm 358 sipm 5 fpm 351 sipm 7 fpm 338 sipm 10 fpm 314 sipm 13 fpm 284 sipm 15 fpm 245 sipm 15
330,365 fpm 324 sipm 4 fpm 317 sipm 6 fpm 305 sipm 9 fpm 284 sipm 12 fpm 257 sipm 13 fpm 222 sipm 14
COPPER ALLOY 623,624 fpm 301 sipm 4 fpm 295 sipm 6 fpm 284 sipm 8 fpm 264 sipm 11 fpm 239 sipm 12 fpm 206 sipm 13
230,260,272 fpm 278 sipm 4 fpm 273 sipm 5 fpm 263 sipm 8 fpm 244 sipm 10 fpm 221 sipm 11 fpm 191 sipm 12
280,464,632,655 fpm 278 sipm 4 fpm 273 sipm 5 fpm 263 sipm 8 fpm 244 sipm 10 fpm 221 sipm 11 fpm 191 sipm 12
101,102,110,122,172 fpm 267 sipm 3 fpm 262 sipm 5 fpm 252sipm 7 fpm 234 sipm 10 fpm 212 sipm 11 fpm 183 sipm 11
1751,182,220,510 fpm 267 sipm 3 fpm 262 sipm 5 fpm 252 sipm 7 fpm 234 sipm 10 fpm 212 sipm 11 fpm 183 sipm 11
625,706,715,934 fpm 267 sipm 3 fpm 262 sipm 5 fpm 252 sipm 7 fpm 234 sipm 10 fpm 212 sipm 11 fpm 183 sipm 11
630 fpm 261 sipm 3 fpm 256 sipm 5 fpm 246 sipm 7 fpm 229 sipm 10 fpm 207 sipm 11 fpm 179 sipm 11
811 fpm 244 sipm 3 fpm 239 sipm 5 fpm 230 sipm 7 fpm 214 sipm 9 fpm 194 sipm 10 fpm 167 sipm 10
12L14 fpm 483 sipm 6 fpm 473 sipm 9 fpm 455 sipm 13 fpm 424 sipm 18 fpm 383 sipm 20 fpm 321 sipm 20
1213,1215 fpm 454 sipm 6 fpm 445 sipm 8 fpm 429 sipm 12 fpm 399 sipm 17 fpm 361 sipm 19 fpm 311 sipm 19
RESULFURIZED 1117 fpm 386 sipm 5 fpm 379 sipm 7 fpm 364 sipm 11 fpm 339 sipm 15 fpm 307 sipm 16 fpm 265 sipm 16
CARBON STEEL 1137 fpm 329 sipm 4 fpm 323 sipm 6 fpm 311 sipm 9 fpm 289 sipm 12 fpm 262 sipm 14 fpm 262 sipm 14
1141,1144 fpm 318 sipm 4 fpm 312 sipm 6 fpm 300 sipm 9 fpm 279 sipm 12 fpm 253 sipm 13 fpm 218 sipm 13
1144 HI STRESS fpm 318 sipm 4 fpm 312 sipm 6 fpm 300 sipm 9 fpm 279 sipm 12 fpm 253 sipm 13 fpm 218 sipm 13
1030 fpm 375 sipm 5 fpm 367 sipm 7 fpm 254 sipm 10 fpm 329 sipm 14 fpm 298 sipm 15 fpm 257 sipm 16
1008,1015,1020,1025 fpm 363 sipm 5 fpm 356 sipm 7 fpm 343 sipm 10 fpm 319 sipm 14 fpm 289 sipm 15 fpm 249 sipm 15
1035 fpm 352 sipm 5 fpm 345 sipm 7 fpm 332 sipm 10 fpm 309 sipm 13 fpm 280 sipm 14 fpm 241 sipm 14
1018,1021,1025 fpm 341 sipm 4 fpm 334 sipm 6 fpm 321 sipm 9 fpm 299 sipm 13 fpm 271 sipm 14 fpm 234 sipm 14
CARBON STEEL 1026,1513 fpm 341 sipm 4 fpm 334 sipm 6 fpm 321 sipm 9 fpm 299 sipm 13 fpm 271 sipm 14 fpm 234 sipm 14
A36 (SHAPES),1040 fpm 307 sipm 4 fpm 301 sipm 6 fpm 289 sipm 8 fpm 269 sipm 12 fpm 243 sipm 13 fpm 210 sipm 13
1042,1541 fpm 284 sipm 4 fpm 278 sipm 5 fpm 268 sipm 8 fpm 249 sipm 11 fpm 225 sipm 12 fpm 195 sipm 12
1044,1045 fpm 250 sipm 3 fpm 245 sipm 5 fpm 236 sipm 7 fpm 219 sipm 9 fpm 198 sipm 10 fpm 171 sipm 11
1060 fpm 227sipm 3 fpm 223 sipm 4 fpm 214 sipm 6 fpm 199 sipm 9 fpm 180 sipm 9 fpm 156 sipm 10
1095 fpm 210 sipm 3 fpm 206 sipm 4 fpm 198 sipm 6 fpm 184 sipm 8 fpm 167 sipm 9 fpm 144 sipm 9
8615,8620,8622 fpm 273 sipm 4 fpm 267 sipm 5 fpm 257 sipm 7 fpm 239 sipm 10 fpm 216 sipm 11 fpm 187 sipm 12
NI-CR-MO 4340,E4340,8630 fpm 250 sipm 3 fpm 245 sipm 5 fpm 236 sipm 7 fpm 219 sipm 9 fpm 198 sipm 10 fpm 171 sipm 11
ALLOY STEEL 8640 fpm 227 sipm 3 fpm 223 sipm 4 fpm 214 sipm 6 fpm 199 sipm 9 fpm 180 sipm 9 fpm 156 sipm 10
E9310 fpm 199 sipm 3 fpm 195 sipm 4 fpm 188 sipm 5 fpm 174 sipm 7 fpm 158 sipm 8 fpm 136 sipm 8
TOOL STEEL L-6 fpm 216 sipm 3 fpm 212 sipm 4 fpm 204 sipm 6 fpm 189 sipm 8 fpm 171 sipm 9 fpm 148 sipm 9
SHOCK RESISTING S-1 fpm 227 sipm 3 fpm 223 sipm 4 fpm 214 sipm 6 fpm 199 sipm 9 fpm 180 sipm 9 fpm 156 sipm 10
TOOL S-5 fpm 159 sipm 2 fpm 156 sipm 3 fpm 150 sipm 4 fpm 140 sipm 6 fpm 126 sipm 7 fpm 109 sipm 7
STEEL S-7 fpm 142 sipm 2 fpm 139 sipm 3 fpm 134 sipm 4 fpm 125 sipm 5 fpm 113 sipm 6 fpm 97 sipm 6
4/29/03
Manual V-16, V-24, VH-24, V-40 & VH-40 18 – Section I
MATERIAL ALLOY 1/2" 1" 2" 4" 7" 12"
A-6 fpm 227 sipm 3 fpm 223 sipm 4 fpm 214 sipm 6 fpm 199 sipm 9 fpm 180 sipm 9 fpm 156 sipm 10
COLD-WORK A-2 fpm 204 sipm 3 fpm 200 sipm 4 fpm 193 sipm 6 fpm 179 sipm 8 fpm 162 sipm 8 fpm 140 sipm 9
TOOL STEEL A-10 fpm 182 sipm 2 fpm 178 sipm 3 fpm 171 sipm 5 fpm 159 sipm 7 fpm 144 sipm 7 fpm 125 sipm 8
D-2 fpm 102 sipm 1 fpm 100 sipm 2 fpm 96 sipm 3 fpm 90 sipm 4 fpm 81 sipm 4 fpm 70 sipm 4
HOT-WORK TOOL H-11,H-12,H-13 fpm 216 sipm 3 fpm 212 sipm 4 fpm 204 sipm 6 fpm 189 sipm 8 fpm 171 sipm 9 fpm 148 sipm 9
OIL HARDENING 0-1 fpm 227 sipm 3 fpm 223 sipm 4 fpm 214 sipm 6 fpm 199 sipm 9 fpm 180 sipm 9 fpm 156 sipm 10
TOOL STEEL 0-6 fpm 216 sipm 9 fpm 212 sipm 12 fpm 204 sipm 6 fpm 189 sipm 8 fpm 171 sipm 9 fpm 148 sipm 9
WATER-HARD
TOOL STEEL W-1 fpm 256 sipm 3 fpm 251 sipm 5 fpm 241 sipm 7 fpm 224 sipm 10 fpm 203 sipm 11 fpm 175 sipm 11
HIGH-SPEED TOOL M-1 fpm 125 sipm 2 fpm 122 sipm 2 fpm 118 sipm 3 fpm 110 sipm 5 fpm 99 sipm 5 fpm 86 sipm 5
STEEL M-2,M-42,T-1 fpm 114 sipm 1 fpm 111 sipm 2 fpm 107 sipm 3 fpm 100 sipm 4 fpm 90 sipm 5 fpm 78 sipm 5
T-15 fpm 79 sipm 1 fpm 78 sipm 1 fpm 75 sipm 2 fpm 70 sipm 3 fpm 63 sipm 3 fpm 54 sipm 3
A242(1) COR-TEN A fpm 341 sipm 4 fpm 334 sipm 6 fpm 321 sipm 9 fpm 299 sipm 13 fpm 271 sipm 14 fpm 234 sipm 14
ALLOY A242(2) COR-TEN B fpm 307 sipm 4 fpm 301 sipm 6 fpm 289 sipm 8 fpm 269 sipm 8 fpm 243 sipm 13 fpm 210 sipm 13
STEEL 300M,HY-80,HY-100 fpm 182 sipm 2 fpm 178 sipm 3 fpm 171 sipm 5 fpm 159 sipm 7 fpm 144 sipm 7 fpm 125 sipm 8
HP 9-4-20,HP 9-4-25 fpm 119 sipm 2 fpm 117 sipm 2 fpm 113 sipm 3 fpm 105sipm 4 fpm 95 sipm 5 fpm 82 sipm 2
MN ALLOY 1330 fpm 250 sipm 3 fpm 245 sipm 5 fpm 236 sipm 7 fpm 219 sipm 9 fpm 198 sipm 10 fpm 171 sipm 11
STEEL 1345 fpm 238 sipm 3 fpm 234 sipm 4 fpm 225 sipm 7 fpm 209 sipm 9 fpm 189 sipm 10 fpm 163 sipm 10
41L40 fpm 312 sipm 4 fpm 306 sipm 6 fpm 295 sipm 9 fpm 274 sipm 12 fpm 248 sipm 13 fpm 214 sipm 13
4130 fpm 307 sipm 4 fpm 301 sipm 6 fpm 289 sipm 8 fpm 269 sipm 12 fpm 243 sipm 13 fpm 210 sipm 13
CR-MO e.t.d.'150 fpm 284 sipm 4 fpm 278 sipm 5 fpm 268 sipm 8 fpm 249 sipm 11 fpm 225 sipm 12 fpm 195 sipm 12
ALLOY STEEL 4140,4142 fpm 284 sipm 4 fpm 278 sipm 5 fpm 268 sipm 8 fpm 249 sipm 11 fpm 225 sipm 12 fpm 195 sipm 12
4145 fpm 238 sipm 3 fpm 234 sipm 4 fpm 225 sipm 7 fpm 209 sipm 9 fpm 189 sipm 10 fpm 163 sipm 10
4150 fpm 227 sipm 3 fpm 223 sipm 4 fpm 214 sipm 6 fpm 199 sipm 9 fpm 180 sipm 9 fpm 156 sipm 10
5160 fpm 250 sipm 3 fpm 245 sipm 5 fpm 236 sipm 7 fpm 219 sipm 9 fpm 198 sipm 10 fpm 171 sipm 11
CR ALLOY STEEL 6150 fpm 238 sipm 3 fpm 234 sipm 4 fpm 225 sipm 7 fpm 209 sipm 9 fpm 189 sipm 10 fpm 163 sipm 10
E52100 fpm 182 sipm 2 fpm 178 sipm 3 fpm 171 sipm 5 fpm 159 sipm 7 fpm 144 sipm 7 fpm 125 sipm 8
420 fpm 216 sipm 3 fpm 212 sipm 4 fpm 204 sipm 6 fpm 189 sipm 8 fpm 171 sipm 9 fpm 148 sipm 9
430 fpm 170 sipm 2 fpm 167 sipm 3 fpm 161 sipm 5 fpm 149 sipm 6 fpm 1235sipm 7 fpm 117 sipm 7
CR STAINLESS 410,502 fpm 159 sipm 2 fpm 156 sipm 3 fpm 150 sipm 4 fpm 140 sipm 6 fpm 126 sipm 7 fpm 109 sipm 7
STEEL 414 fpm 131 sipm 2 fpm 128 sipm 2 fpm 123 sipm 4 fpm 115 sipm 5 fpm 104 sipm 5 fpm 90 sipm 6
431 fpm 108 sipm 1 fpm 106 sipm 2 fpm 102 sipm 3 fpm 95 sipm 4 fpm 86 sipm 4 fpm 74 sipm 5
440C fpm 91 sipm 1 fpm 89 sipm 2 fpm 86 sipm 2 fpm 80 sipm 3 fpm 72 sipm 4 fpm 62 sipm 4
MOLD STEEL P-20 fpm 261 sipm 3 fpm 256 sipm 5 fpm 246 sipm 7 fpm 229 sipm 10 fpm 207 sipm 11 fpm 179 sipm 11
STAINLESS STEEL CUSTOM 450,456 fpm 91 sipm 1 fpm 89 sipm 2 fpm 86 sipm 2 fpm 80 sipm 3 fpm 72 sipm 4 fpm 62 sipm 4
304,324 fpm 136 sipm 2 fpm 134 sipm 3 fpm 129 sipm 4 fpm 120 sipm 5 fpm 108 sipm 6 fpm 93 sipm 6
304L fpm 131 sipm 2 fpm 128 sipm 2 fpm 123 sipm 4 fpm, 115 sipm 5 fpm 104 sipm 5 fpm 90 sipm 6
347 fpm 125 sipm 2 fpm 122 sipm 2 fpm 118 sipm 3 fpm 110 sipm 5 fpm 99 sipm 5 fpm 86 sipm 5
AUSTENITIC 316,316L fpm 114 sipm 1 fpm 111 sipm 2 fpm 107 sipm 3 fpm 100 sipm 4 fpm 90 sipm 5 fpm 78 sipm 5
STAINLESS STEEL 18-18-2,309 fpm 102 sipm 1 fpm 100 sipm 2 fpm 96 sipm 3 fpm 90 sipm 4 fpm 81 sipm 4 fpm 70 sipm 4
310 fpm 91 sipm 1 fpm 89 sipm 2 fpm 86 sipm 2 fpm 80 sipm 3 fpm 72 sipm 4 fpm 62 sipm 4
22-13-5 fpm 68 sipm 1 fpm 67 sipm 1 fpm 64 sipm 2 fpm 60 sipm 3 fpm 54 sipm 3 fpm 47 sipm 3
4/29/03
Manual V-16, V-24, VH-24, V-40 & VH-40 19 – Section I
NITRONIC 50,60 fpm 68 sipm 1 fpm 67 sipm 1 fpm 64 sipm 2 fpm 60 sipm 3 fpm 54 sipm 3 fpm 47 sipm 3
MATERIAL ALLOY 1/2" 1" 2" 4" 7" 12"
MARTENSITIC
STAINLESS STEEL GREEK ASCOLOY fpm 108 sipm 1 fpm 106 sipm 2 fpm 102 sipm 3 fpm 95 sipm 4 fpm 86 sipm 4 fpm 74 sipm 5
416 fpm 216 sipm 3 fpm 212 sipm 4 fpm 204 sipm 6 fpm 189 sipm 8 fpm 171 sipm 9 fpm 148 sipm 9
FREE MACHINING 440 F fpm 182 sipm 2 fpm 178 sipm 3 fpm 171 sipm 5 fpm 159 sipm 7 fpm 144 sipm 7 fpm 125 sipm 8
STAINLESS STEEL 203 EZ,430 F fpm 170 sipm 2 fpm 167 sipm 3 fpm 161 sipm 5 fpm 149 sipm 6 fpm 135 sipm 7 fpm 117 sipm 7
303,303 PB,303 SE fpm 159 sipm 2 fpm 156 sipm 3 fpm 150 sipm 4 fpm 140 sipm 6 fpm 126 sipm 67 fpm 109 sipm 7
416 fpm 216 sipm 3 fpm 212 sipm 4 fpm 204 sipm 6 fpm 189 sipm 8 fpm 171 sipm 9 fpm 148 sipm 9
FREE MACHINING 440 F fpm 182 sipm 2 fpm 178 sipm 3 fpm 171 sipm 5 fpm 159 sipm 7 fpm 144 sipm 7 fpm 125 sipm 8
STAINLESS STEEL 203 EZ,430 F fpm 170 sipm 2 fpm 167 sipm 3 fpm 161 sipm 5 fpm 149 sipm 6 fpm 135 sipm 7 fpm 117 sipm 7
303,303 PB,303 SE fpm 159 sipm 2 fpm 156 sipm 3 fpm 150 sipm 4 fpm 140 sipm 6 fpm 126 sipm 67 fpm 109 sipm 7
FERRITIC FERRALIUM 255 fpm 102 sipm 1 fpm 100 sipm 2 fpm 96 sipm 3 fpm 90 sipm 4 fpm 81 sipm 4 fpm 70 sipm 4
AUSTENITIC S.S. 2205 fpm 91 sipm 1 fpm 89 sipm 2 fpm 86 sipm 2 fpm 80 sipm 3 fpm 72 sipm 4 fpm 62 sipm 4
15-5 PH fpm 91 sipm 1 fpm 89 sipm 2 fpm 86 sipm 2 fpm 80 sipm 3 fpm 72 sipm 4 fpm 62 sipm 4
PRECIPITATION 17-4 PH,17-7 PH fpm 91 sipm 1 fpm 89 sipm 2 fpm 86 sipm 2 fpm 80 sipm 3 fpm 72 sipm 4 fpm 62 sipm 4
HARDENABLE AM 350,AM 355 fpm 91 sipm 1 fpm 89 sipm 2 fpm 86 sipm 2 fpm 80 sipm 3 fpm 72 sipm 4 fpm 62 sipm 4
STAINLESS STEEL PH 13-8 MO fpm 91 sipm 1 fpm 89 sipm 2 fpm 86 sipm 2 fpm 80 sipm 3 fpm 72 sipm 4 fpm 62 sipm 4
PH 14-8 MO fpm 91 sipm 1 fpm 89 sipm 2 fpm 86 sipm 2 fpm 80 sipm 3 fpm 72 sipm 4 fpm 62 sipm 4
PH 15-7 MO fpm 85 sipm 1 fpm 84 sipm 2 fpm 80 sipm 2 fpm 75 sipm 3 fpm 68 sipm 4 fpm 58 sipm 4
MAGNESIUM AZ31B MAG-
ALLOY NESIUM ALLOY fpm 568 sipm 7 fpm 557 sipm 11 fpm 536 sipm 16 fpm 498 sipm 21 fpm 451 sipm 23 fpm 389 sipm 24
IRON BASE PYROMET X-15 fpm 136 sipm 2 fpm 134 sipm 3 fpm 129 sipm 4 fpm 120 sipm 5 fpm 108 sipm 6 fpm 93 sipm 6
SUPER ALLOY A286 fpm 102 sipm 1 fpm 100 sipm 2 fpm 96 sipm 3 fpm 90 sipm 4 fpm 81 sipm 4 fpm 70 sipm 4
INCOLOY 800,801 fpm 102 sipm 1 fpm 100 sipm 2 fpm 96 sipm 3 fpm 90 sipm 4 fpm 81 sipm 4 fpm 70 sipm 4
COBALT BASE ASTROLOY M fpm 68 sipm 1 fpm 67 sipm 1 fpm 64 sipm 2 fpm 60 sipm 3 fpm 54 sipm 3 fpm 47 sipm 3
ALLOY WF-11 fpm 74 sipm 1 fpm 72 sipm 1 fpm 70 sipm 2 fpm 65 sipm 3 fpm 59 sipm 3 fpm 51 sipm 3
TI-3A1-8V-6CR-4MO-4Zr fpm 91 sipm 1 fpm 91 sipm 1 fpm 91 sipm 1 fpm 91 sipm 1 fpm 91 sipm 1 fpm 91 sipm 1
TI-8Mo-8V-2Fe-3Al fpm 91 sipm 1 fpm 91 sipm 1 fpm 91 sipm 1 fpm 91 sipm 1 fpm 91 sipm 1 fpm 91 sipm 1
TI-2Al-11Sn-5Zr-1Mo fpm 85 sipm 1 fpm 84 sipm 2 fpm 80 sipm 2 fpm 75 sipm 3 fpm 68 sipm 4 fpm 58 sipm 4
TITANIUM ALLOY TI-5Al-2.5Sn fpm 85 sipm 1 fpm 84 sipm 2 fpm 80 sipm 2 fpm 75 sipm 3 fpm 68 sipm 4 fpm 58 sipm 4
TI-6Al-2Sn-4Zr-2Mo fpm 85 sipm 1 fpm 84 sipm 2 fpm 80 sipm 2 fpm 75 sipm 3 fpm 68 sipm 4 fpm 58 sipm 4
TI-6Al-4V fpm 79 sipm 1 fpm 78 sipm 1 fpm 75 sipm 2 fpm 70 sipm 3 fpm 63 sipm 3 fpm 54 sipm 3
TI-7Al-4Mo fpm 74 sipm 1 fpm 72 sipm 1 fpm 70 sipm 2 fpm 65 sipm 3 fpm 59 sipm 3 fpm 51 sipm 3
TI-8Al-1Mo-1V fpm 74 sipm 1 fpm 72 sipm 1 fpm 70 sipm 2 fpm 65 sipm 3 fpm 59 sipm 3 fpm 51 sipm 3
NICKEL ALLOY NICKEL 200,201,205 fpm 97 sipm 1 fpm 95 sipm 2 fpm 91 sipm 3 fpm 85 sipm 4 fpm 77 sipm 4 fpm 66 sipm 4
INCONEL 625 fpm 114 sipm 1 fpm 111 sipm 2 fpm 107 sipm 3 fpm 100 sipm 4 fpm 90 sipm 5 fpm 78 sipm 5
INCOLOY 802,804 fpm 102 sipm 1 fpm 100 sipm 2 fpm 96 sipm 3 fpm 90 sipm 4 fpm 81 sipm 4 fpm 70 sipm 4
MONEL R405 fpm 97 sipm 1 fpm 95 sipm 2 fpm 91 sipm 3 fpm 85 sipm 4 fpm 77 sipm 4 fpm 66 sipm 4
NICKEL BASE 20CB3 fpm 91 sipm 1 fpm 89 sipm 2 fpm 86 sipm 2 fpm 80 sipm 3 fpm 72 sipm 4 fpm 62 sipm 4
ALLOY MONEL 400,401 fpm 85 sipm 1 fpm 84 sipm 2 fpm 80 sipm 2 fpm 75 sipm 3 fpm 68 sipm 4 fpm 58 sipm 4
(*HASTELLOY) *B,B-2,C,C-22 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1
*C-276,C-4 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1
*F,G,G-2,3,G-30 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1
*N,S,W,X , INCOLOY
825
fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1
4/29/03
Manual V-16, V-24, VH-24, V-40 & VH-40 20 – Section I
MATERIAL ALLOY 1/2" 1" 2" 4" 7" 12"
INCONEL 751,X750 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1
NICKEL BASE WASPALOY fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1
ALLOY MONEL K500 fpm 74 sipm 1 fpm 72 sipm 1 fpm 70 sipm 2 fpm 65 sipm 3 fpm 59 sipm 3 fpm 51 sipm 3
(*HASTELLOY) INCOLOY 901,903,926 fpm 68 sipm 1 fpm 67 sipm 1 fpm 64 sipm 2 fpm 60 sipm 3 fpm 54 sipm 3 fpm 47 sipm 3
INCONEL 600,718 fpm 68 sipm 1 fpm 67 sipm 1 fpm 64 sipm 2 fpm 60 sipm 3 fpm 54 sipm 3 fpm 47 sipm 3
NI-SPAN-C 902 fpm 68 sipm 1 fpm 67 sipm 1 fpm 64 sipm 2 fpm 60 sipm 3 fpm 54 sipm 3 fpm 47 sipm 3
NIMONIC 263 fpm 68 sipm 1 fpm 67 sipm 1 fpm 64 sipm 2 fpm 60 sipm 3 fpm 54 sipm 3 fpm 47 sipm 3
RENE 41,UDIMET 500 fpm 68 sipm 1 fpm 67 sipm 1 fpm 64 sipm 2 fpm 60 sipm 3 fpm 54 sipm 3 fpm 47 sipm 3
NIMONIC 75 fpm 57 sipm 1 fpm 56 sipm 1 fpm 54 sipm 2 fpm 50 sipm 2 fpm 45 sipm 2 fpm 39 sipm 2
ASTM A220 (50005) fpm 273 sipm 4 fpm 267 sipm 5 fpm 257 sipm 7 fpm 239 sipm 10 fpm 216 sipm 11 fpm 187 sipm 12
CAST IRONS ASTM A220 (60004) fpm 193 sipm 3 fpm 189 sipm 4 fpm 182 sipm 5 fpm 169 sipm 7 fpm 153 sipm 8 fpm 132 sipm 8
PEARLITIC ASTM A220 (70003) fpm 165 sipm 2 fpm 161 sipm 3 fpm 155 sipm 5 fpm 144 sipm 6 fpm 131 sipm 7 fpm 133 sipm 7
MALLEABLE ASTM A220 (80002) fpm 142 sipm 2 fpm 139 sipm 3 fpm 134 sipm 4 fpm 125 sipm 5 fpm 113 sipm 6 fpm 97 sipm 6
ASTM A220 (90001) fpm 114 sipm 1 fpm 111 sipm 2 fpm 107 sipm 3 fpm 100 sipm 4 fpm 90 sipm 5 fpm 78 sipm 5
ASTM A436 (1B) fpm 170 sipm 2 fpm 167 sipm 3 fpm 161 sipm 5 fpm 149 sipm 6 fpm 135 sipm 7 fpm 117 sipm 7
GRAY IRON ASTM A436 (2) fpm 159 sipm 2 fpm 156 sipm 3 fpm 150 sipm 4 fpm 140 sipm 6 fpm 125 sipm 7 fpm 109 sipm 7
AUSTENITIC ASTM A436 (2B) fpm 142 sipm 2 fpm 139 sipm 3 fpm 134 sipm 4 fpm 125 sipm 5 fpm 133 sipm 6 fpm 97 sipm 6
DUCTILE ASTM A439 (D-2) fpm 91 sipm 1 fpm 89 sipm 2 fpm 86 sipm 2 fpm 80 sipm 3 fpm 72 sipm 4 fpm 62 sipm 4
AUSTENITIC ASTM A439 (D2-B) fpm 68 sipm 1 fpm 67 sipm 1 fpm 64 sipm 2 fpm 60 sipm 3 fpm 54 sipm 3 fpm 47 sipm 3
MALLEABLE ASTM A47(50&53ksi) fpm 341 sipm 4 fpm 334 sipm 6 fpm 321 sipm 9 fpm 299 sipm 13 fpm 271 sipm 14 fpm 234 sipm 14
ASTM A48 (20ksi) fpm 261 sipm 3 fpm 256 sipm 5 fpm 246 sipm 7 fpm 229 sipm 10 fpm 207 sipm 11 fpm 179 sipm 11
GARY IRON ASTM A48 (40ksi) fpm 204 sipm 3 fpm 200 sipm 4 fpm 193 sipm 6 fpm 179 sipm 8 fpm 162 sipm 8 fpm 140 sipm 9
ASTM A48 (60ksi) fpm 114 sipm 1 fpm 111 sipm 2 fpm 107 sipm 3 fpm 100 sipm 4 fpm 90 sipm 5 fpm 78 sipm 5
ASTM A536 (60-40-18) fpm 409 sipm 5 fpm 401 sipm 8 fpm 396 sipm 11 fpm 359 sipm 15 fpm 325 sipm 17 fpm 280 sipm 17
DUCTILE ASTM A536 (88-55-06) fpm 273 sipm 4 fpm 267 sipm 5 fpm 257 sipm 7 fpm 239 sipm 10 fpm 216 sipm 11 fpm 187 sipm 12
ASTM A536 (100-70-03) fpm 210 sipm 3 fpm 206 sipm 4 fpm 198 sipm 6 fpm 184 sipm 8 fpm 167 sipm 9 fpm 144 sipm 9
ASTM A536 (120-90-02) fpm 136 sipm 2 fpm 134 sipm 3 fpm 129 sipm 4 fpm 120 sipm 5 fpm 108 sipm 6 fpm 93 sipm 6
RATE REDUCTION FOR HARD MATERIALS
Below is a matrix for speed reduction for hard materials. Find the material hardness, either Rockwell
(Rc) or Brinell (Bhn), and reduce both band speed and cutting rate by the percentage shown.
HARDNESS (Rc) HARDNESS (Bhn) SPEED / CUTTING
Rockwell Brinell
RATE REDUCTION
Up to 20 226 0%
22 237 5%
24 247 10%
26 258 15%
28 271 20%
30 286 25%
32 301 30%
34 319 33%
36 336 35%
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25

Johnson Hardware VH-40 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI