2. SoundShaker
  3. TA-4800

SoundShaker TA-4800 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the SoundShaker TA-4800 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
INSTALLATION GUIDE
TA-
TABLE OF CONTENTS
What’s in the box?
Single Bass/Dual Bass Receiver Setup
SoundShaker Amplifier Setup
Commonly Asked Questions
Wireless Syncing
1
2
3
4
5
Page 1
Part No. 5102
Amplifier
Part No. 5024
Transmitter
Part No. 5465
Power Supply for Amplifier
Part No. 5423
Power Supply for Transmitter
Part No. 8091
Amp Base
Part No. 3120
Long Cable
Part No. 3031
Y-Cable (M/2F)
Part No. 3032
Y-Cable (M/2M)
WHAT’S IN THE BOX?
Page 2
SINGLE BASS OUT RECEIVER SETUP
This is the transmitter setup for a single bass out. Please follow each step to ensure that your transmitter and amplifier
are connected correctly.
STEP 3. CONNECT YOUR RECEIVER & SUBWOOFER
STEP 2. CONNECT THE  Y-CABLE
STEP 2. CONNECT THE  Y-CABLE
Connect the single end of the 3032 Y-Cable to one
split end of the 3031 Y-Cable.
Connect the single end of the 3032 Y-Cable to your
receiver.
STEP 3. CONNECT THE  Y-CABLE TO YOUR RECEIVER & SUBWOOFER
Connect the remaining ends of the 3031 Y-Cable to both your receiver and your
subwoofer. Once all connections are secure power up the transmitter.
Connect your receiver to your subwoofer. Once all connections are secure
power up the transmitter.
STEP 1. CONNECT THE  Y-CABLE AND POWER SUPPLY
STEP 1. CONNECT THE  Y-CABLE AND POWER SUPPLY
Connect the power supply for the transmitter.
Connect the split cable end of the 3032 Y-Cable to
the
Audio In
on the transmitter.
Connect the power supply for the transmitter.
Connect the split cable end of the 3032 Y-Cable to
the
Audio In
on the transmitter.
3032 Y-Cable
5423 Power Supply
3032 Y-Cable
3031 Y-Cable
Your Receiver
Your Receiver
Your Subwoofer
Your Subwoofer
1
1
2
2
3
3
5024 Transmitter
OFF-ON CODE
DUAL BASS OUT RECEIVER SETUP
This is the transmitter setup for a double bass out. Please follow each step to ensure that your transmitter and amplifier
are connected correctly.
Cable Not
Included
Cable Not
Included
5024 Transmitter
5423 Power Supply
OFF-ON CODE
Page 3
Connect the 3120 Long Cable to the SoundShaker port
on the back of the 5012 Amplifier.
STEP 5. CONNECT THE LONG CABLE AND POWER SUPPLY
STEP 6a-6b. CONNECT THE LONG CABLE TO SHORT CABLES
STEP 7a-7b. CONNECT SHORT CABLES TO SOUNDSHAKER(S)
The 3120 Long Cable attaches to the 81-3108 Short Cables.
Connect Power
Supply to 15V DC
Port on the back
of SoundShaker
Amplifier.
NOTE: You can connect up to a total
of 4 SoundShakers to each amplifier.
Finish by connecting each SoundShaker to a 81-3108 short cable.
SoundShaker 1
SoundShaker 2
SoundShaker 3
SoundShaker 4
AUDIO-IN 15V DC TRANSDUCERS
POWER X-OVER WIRELESS CODE
OFF
1
2
3
4
5
6
7
8
9
10
50HZ
55HZ
60HZ
65HZ
70HZ
75HZ
80HZ
85HZ
90HZ
95HZ
100HZ
SOUNDSHAKER AMPLIFIER SETUP
This is the main amplifier setup. Please follow each to step to ensure that your amplifier is installed
correctly. Make sure the transmitter is installed and is sending a signal out during the amplifier setup.
5012 SoundShaker Amplifier (Front)
5012 SoundShaker Amplifier (Rear)
5
6a
6b
6c
6d
7a
7b
7c
7d
3120 Long Cable
5465 Power Supply
81-3108 Short Cable
81-3108 Short Cable
81-3108 Short Cable
81-3108 Short Cable
*SoundShakers are sold
seperately.
Page 4
COMMONLY ASKED QUESTIONS
Below is a list of commonly asked questions. If you have any trouble with your SoundShaker please refer to
the information below.
Q. DOES THE ORDER IN WHICH I CONNECT MY SOUNDSHAKERS MATTER?
A. No, the order in which your SoundShakers are connected to the long cable will not matter.
The signal runs to all outputs when powered.
Q. MY SOUNDSHAKER SYSTEM DOES NOT APPEAR TO BE WORKING.
A. Check and make sure all connections and power supplies are secured. Make sure your
transmitter, amplifier, receiver, and subwoofer are all powered up.
Q. IS SOUNDSHAKER COMPATIBLE WITH OTHER WIRELESS AUDIO SYSTEMS?
A. SoundShaker is compatible with any audio system that provides an RCA output to connect
SoundShaker to.
Q. I’VE SYNC’D MY AMP BUT DON’T FEEL ANY VIBRATIONS.
A. When syncing your amp be sure to check that an audio signal is being sent out. Your amplifier
will not sync without a signal currently running. Refer to the illustration on the next page to
learn how to sync up your amplifier.
Page 5
SOUNDSHAKER WIRELESS SYNCING
Please follow each to step to ensure that your equipment syncs correctly.
Make sure Wireless Switch is set to . MAKE
SURE YOU HAVE A MOVIE OR MUSIC PLAYING,
press and hold Code Button for a minimum of
3 seconds to begin syncing process. When light
blinks rapidly proceed to step 2.
Press and hold Code Button for a minimum of 3
seconds until light blinks rapidly. Red light will turn
solid when pairing is completed. (Both units should
have solid red lights when paired.)
STEP . HOLD TRANSMITTER CODE BUTTON TO COMPLETE
SYNC WITH AMP
POWER X-OVER WIRELESS CODE
OFF
1
2
3
4
5
6
7
8
9
10
50HZ
55HZ
60HZ
65HZ
70HZ
75HZ
80HZ
85HZ
90HZ
95HZ
100HZ
STEP . HOLD AMPLIFIER CODE BUTTON TO BEGIN SYNC
PLEASE NOTE: YOUR SOUNDSHAKER SHOULD ALREADY BE SYNC’D
WITH YOUR SOUNDSHAKER AMPLIFIER.
1
OFF-ON CODE
2
5012 Amplifier
5024 Transmitter
/