Frigidaire GLCS376CBA Owner's manual

Brand: Frigidaire

Model: GLCS376CBA

Category: Cookers

Type: Owner's manual

This manual is also suitable for

Visit the Frigidaire Web Site at:

http://www.frigidaire.com

Page

Registration ....................................................... 2

Important Safety Instructions .....................................3-5

Selecting Surface Cooking Utensils ................................ 5

SpecialtyPans& Trivets..................................................6

CanningTips & Information ...........................................6

Liquefied Petroleum (Propane)

GasConversion...............................................................7

FlameSize.......................................................................7

Proper BurnerAdjustments .............................................7

Setting Surface Controls ................................................. 8

BeforeSetting OvenControls.......................................... 8

Setting OvenControls ..................................................... 8

BeforeSetting Warmer DrawerControls .........................9

SettingWarmer DrawerControls .............................. 9-10

Convection Cooking...................................................... 10

Convection Roasting .................................................... 10

SpeedBakeTM Cooking System ...................................... 11

OvenBaking.................................................................. 12

Air Circulation in the Oven ............................................ 12

Broiling ..........................................................................13

GeneralCleaning..................................................... 14-19

ChangingOven Light .................................................... 19

Avoid ServiceChecklist ........................................... 19-22

Notes.............................................................................23

Warranty........................................................................24

READ AND SAVE THESE INSTRUCTIONS 318200861 (0111)Rev. C

Product Registration

The self-addressed PRODUCT

REGISTRATION CARD should be filled in

completely, signed and returned to

Electrolux Home Products North America.

Versibn en espafiol

Sidesea obtener una copia en espahol de

este Manual del Usuario, s[rvaseescribir a

la direcci6n que se incluye a

continuaci6n. Solicite la P/N318204007.

SpanishOwner's Guides

Electrolux Home Products North America

Consumer Relations

RO. Box 212378

Augusta, Georgia

30917-2378

Thank you for choosing this appliance. The information contained within this

Owner's Guide will instruct you on how to properly operate and care for your

range. Pleaseread through the information contained in your literature pack to

learn more about your new appliance.

Record Your Model and Serial Numbers

Record in the space provided belowthe model and serial numbers. The numbers

are found on the serial plate located at the left of the range frame and are visible

when the oven door isopen or on the inside of the drawer along the side of the

frame.

Model Number:

Serial Number:

Date of Purchase:

This Owner's Guide contains general operating instructions for your range and

feature information for several models. Your range may not have all the

described features. The graphics shown are representational. The graphics on

your range may not look exactly like those shown.

Note: The instructions appearing in this Owner's Guide are not meant to cover

every possible condition and situation that may occur. Common sense and

caution must be practiced when installing, operating and maintaining any

appliance.

Important: Keep a copy of your bill of sale.

The date on the bill establishes the warranty period service be required. Placeit

where it can be easily retrieved. If service is performed while the appliance is

under warranty, you may have to show your bill of sale.

[=1

• All ranges

can tip.

• Injuryto per-

sons could re-

sult.

• Install anti-tip

device

packed with

range.

• SeeInstalla-

tion instruc-

tions.

Fr.vvAv!-'1:!_ll_[€_To reduce

the risk of tipping of the

range, the range must be

secured by properly in-

stalled anti-tip bracket (s)

provided with the range.

To check if the bracket (s)

is installed properly, re-

move the lower panel or

storage drawer and verify

that the anti-tip bracket (s)

is engaged. Refer to the

installation instructions for

proper anti-tip bracket(s).

If the information in this manual is not

followed exactly, a fire or explosion may result causing

property damage, personal injury or death.

FOR YOUR SAFETY:

Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance.

- WHAT TO DO IF YOU SMELL GAS:

* Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor's

phone. Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the fire

department.

Installation and service must be performed by a

qualified installer, servicer or gas supplier.

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions before using this appliance.

Save these instructions for future reference.

This guide contains important safety symbols and instructions. Please pay special attention to these symbols and follow all

instructions given. Here isa brief explanation of the useof these symbols.

This symbol will help alert you to situations that may cause serious bodily harm, death or property damage.

This symbol will help alert you to situations that may cause bodily injury or property damage.

* Remove all tape and packaging wrap before using the

appliance. Destroy the carton and plastic bags after

unpacking the appliance. Never allow children to play

with packaging material.

• Proper Installation--Be sure your appliance isproperly

installed and grounded by a qualified technician in

accordance with National Fuel Gas Code ANSI Z223.1

latest edition, and National Electrical Code ANSI/NFPA

No. 70, latest edition and local requirements. Install

only per installation instructions provided in the literature

package for this appliance.

Ask your dealer to recommend a qualified technician and an

authorized repair service. Know how to disconnect the

electrical power to the appliance at the circuit breaker or fuse

box and gas supply at the main shutoff valve in case of an

emergency. Remove the drawer to accessthe valve.

• User Servicing--Do not repair or replace any part of

the appliance unless specifically recommended in the

manuals. All other servicing should be done only by a

qualified technician to reduce the risk of personal injury and

damage to the appliance.

* Never modify or alter the construction of an appliance

by removing leveling legs, panels, wire covers, anti-tip

brackets/screws, or any other part of the product.

Stepping, leaning or sitting on the door

or drawer of this appliance can result in serious injuries

and may also cause damage to the appliance. Do not

allow children to climb or play around the appliance. The

weight of a child on an open door may cause the appliance to

tip, resulting in serious burns or other injury. An open drawer,

when hot, may cause burns.

Do not use the oven or warmer drawer (if

equipped) for storage.

• Storage in or on Appliance--Flammable materials

should not be stored in an oven, near surface burners

or in the drawer (if equipped). This includespaper, plastic

and cloth items, such ascookbooks, plasticware and towels,

as well as flammable liquids. Do not store explosives, such

as aerosol cans, on or near the appliance. Flammable

materials may explode and result in fire or property damage.

Do not store items of interest to children

in the cabinets above the appliance.

Do not leave children alone. Children should not be

left alone or unattended in the area where an appli-

ance is in use. They should never be allowed to sit or stand

on any part of the appliance.

DO NOT TOUCH SURFACE BURNERS, GRATES, AREAS

NEAR THESE BURNERS, OVEN HEATING ELEMENTS OR

INTERIOR SURFACES OF THE OVEN OR WARMER

DRAWER (if equipped). Both surface burners and oven

heating elements may be hot even though they are dark in

color. Areas near surface burners may become hot enough

to cause burns. During and after use, do not touch, or let

clothing or other flammable materials touch these areas

until they have had sufficient time to cool. Among these

areasare the cooktop, surfaces facing the cooktop, the oven

vent openings and surfaces near these openings, oven door

and window.

Wear Proper Apparel--Loose-fitting or hanging gar-

ments should never be worn while using the appli-

ance. Do not let clothing or other flammable materials

contact hot surfaces.

Never use your appliance for warming or

heating the room.

* Do Not Use Water or Flour on Grease Fires--Smother

the fire with a pan lid, or use baking soda, a dry

chemical or foam-type extinguisher.

* When heating fat or grease, watch it closely. Fat or

grease may catch fire if allowed to become too hot.

In case of fire or gas leak, be sure to turn

off the main gas shutoff valve.

* Use Only Dry Potholders--Moist or damp potholders

on hot surfaces may result in burns from steam. Do not

let the potholders touch the flame, burners or interior oven

elements. Do not usea towel or other bulky cloth instead of

a potholder.

* Do Not Heat Unopened Food Containers--Build up of

pressure may cause the container to burst and result in

injury.

IMPORTANT SAFETY INSTRUCTIONS (continued)

* Remove the oven door from any unused appliance if it

is to be stored or discarded.

• IMPORTANT--Do not attempt to operate the oven

during a power failure. If the power fails, always turn

the oven off. If the oven is not turned off and the power

resumes, the oven may begin to operate again. Food left

unattended could catch fire or spoil.

Use Proper Flame Size--Adjust flame size

so it does not extend beyond the edge of the utensil. The

useof undersized utensils will exposed a portion of the burner

flame to direct contact and may result in ignition of clothing.

Proper relationship of utensil to flame will also improve

efficiency.

Do not use stove top grills on the burner

grates of your sealed gas burners. If you use a stove top

grill on a sealed gas burner, it will cause incomplete combus-

tion and can result in exposure to carbon monoxide levels

above allowable current standards. This can be hazardous to

your health.

Electronic controllers can be damaged by

cold temperatures. When you use your appliance for the

first time, or if it has not been used for a long period of

time, make sure that it has been exposed to a tempera-

ture above 0°C/32°F for at least 3 hours before connect-

ing it to the power supply.

IMPORTANT INSTRUCTIONS FOR USING YOUR

COOKTOP

• Know which knob controls each surface heating unit.

Always turn the knob to the LITEposition when igniting the

burners. Visually check that the burner has lit. Then adjust

the flame so it does not extend beyond the edge of the

utensil.

• Use Proper Pan SizeiThis appliance isequipped with one

or more surface burners of different sizes. Select utensils

having flat bottoms large enough to cover the surface

burner. The useof undersized utensils will expose a portion

of the surface burner to direct contact and may result in

ignition of clothing. Proper relationship of utensil to the

surface burner will also improve efficiency.

• Utensil Handles Should Be Turned Inward and Should

Not Extend Over Adjacent Surface BurnersiTo reduce

the risk of burns, ignition of flammable materials, and

spillage due to unintentional contact with the utensil. The

handle of the utensil should be positioned so that it isturned

inward, and does not extend over adjacent surface burner.

• Never Leave Surface Burners UnattendediBoilovers

cause smoking and greasy spillovers that may ignite, or a

pan that has boiled dry may melt.

Protective liners i Do not use aluminum foil to line oven

bottom or any other part of the appliance. Only use

aluminum foil as recommended for baking if used asa cover

placed on the food. Any other used of protective liners or

aluminum foil may result in a risk of electric shock or fire or

a short circuit.

Glazed Cooking UtensilsiOnly certain types of glass,

glass/ceramic, ceramic, earthenware, or other glazed uten-

silsare suitable for rangetop servicewithout breaking due to

the sudden change in temperature. Check the

manufacturer's recommendations for rangetop use.

Do Not Use Decorative Surface Burner Covers. If a

burner is accidentally turned on, the decorative cover will

become hot and possibly melt. Burns will occur if the hot

covers are touched. Damage may also be done to the

cooktop or burners because the covers may cause overheat-

ing. Air will be blocked from the burner and cause

combustion problems.

IMPORTANT INSTRUCTIONS FOR USING YOUR

OVEN

• Use Care When Opening Door or Warmer Drawer (if

equipped)iStand to the side of the appliance when

opening the door of a hot oven. Let hot air or steam escape

before you remove or replace food in the oven/warmer

drawer.

Keep Oven Vent Ducts Unobstructed. The oven isvented

at the rear of the cooktop. Touching the surfaces in this area

when the oven is operating may cause severe burns. Also,

do not place plastic or heat-sensitive items on or near the

oven vent. These items could melt or ignite.

Placement of Oven/Warmer Drawer (if equipped)

Racks. Always place oven racks in desired location while

oven/drawer (if equipped) iscool. Remove all utensils from

the rack before removing rack. If rack must be moved while

oven ishot, useextreme caution. Use potholders and grasp

the rack with both hands to reposition. Do not let potholders

contact the hot oven element or interior of the oven/warmer

drawer (if equipped).

• Do not use the broiler pan without its insert. The broiler

pan and grid allow dripping fat to drain and be kept away

from the high heat of the broiler.

• Do not cover the broiler or warmer drawer (if

equipped) grid with aluminum foil. Exposed fat and

grease could ignite.

Do not touch a hot light bulb with a damp cloth. Doing

so could cause the bulb to break. Disconnect the appliance

or turn off the power to the appliance before removing and

replacing light bulb.

IMPORTANT SAFETY INSTRUCTIONS (continued)

IMPORTANT INSTRUCTIONS FOR CLEANING

YOUR RANGE

• Clean the appliance regularly to keep all parts free of

grease that could catch fire. Exhaustfan ventilation hoods

and grease filters should be kept clean. Do not allow grease

to accumulate. Greasydeposits in the fan could catch fire.

Refer to the hood manufacturer's instructions for cleaning.

• Do not clean the oven door gasket. The door gasket is

essential for a good seal. Care should be taken not to rub,

damage or move the gasket.

• Do not use oven cleaners. No oven cleaner or oven liner

protective coating of any kind should be used in or around

any part of the oven.

• Cleaners/aerosolsiAIways follow the manufacturer's rec-

ommended directions for use. Be aware that excessresidue

from cleaners and aerosols may ignite causing damage and/

or injury.

SELF-CLEANING OVENS

• Clean in the self-cleaning cycle only the parts of the

oven listed in this owner's guide. Before self-cleaning

the oven, remove the broiler pan and any utensils stored in

the oven.

• Remove oven racks. Oven racks color will change if left in

the oven during a self-cleaning cycle.

The health of some birds is extremely

sensitive to the fumes given off during the self-clean

cycle of any range. Move birds to another well venti-

lated room.

IMPORTANT SAFETY NOTICE

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of

substances known to the state to cause cancer, birth defects or other reproductive harm, and requires businessesto warn

customers of potential exposure to such substances.

SAVE THESE INSTRUCTIONS

Selecting Surface Cooking Utensils

For best results and energy conservation, choose cooki ng utensils that havethese characteristics:

Pansshould have flat bottoms. Check for

flatness byrotating a ruler acrossthe bot-

tom. There should be no gaps between

the pan and ruler.

Note: Always usea utensil for its intend-

ed purpose. Follow manufacturer's in-

structions. Some utensils were not made

to be usedin the oven or on the cooktop.

Note: Do not usegriddle over more than

one burner. That can damage your

cooktop and that can result in exposure

to carbon monoxide levels above allow-

able current standards. That can hazard-

ous to your health.

*GOOD

• Flat bottom and straight sides.

• Tight fitting lids.

• Weight of handle does not tilt

pan. Pan iswell balanced.

• Pansizes match the amount of

food to be prepared.

• Made of material that conducts

heat well.

• Easyto clean.

POOR

• Curved and warped pan bottoms.

• Pan overhangs unit by more than

2.5 cm (1").

• Heavy handle tilts pan.

• Flame extends beyond unit.

* Specialty pans such aslobster pots, griddles and pressure cookers may be used

but must conform to the above recommended cookware requirements.

Specialty Pans & Trivets

Woks with flat bottoms suitable for

use on your cooktop are available in

most cookshop or hardware stores.

Round-bottomed woks (with asupport

ring that does not extend beyond the

burner unit) may also be used. The

metal ringwas designedtosupportthe

wok safely when it is filled with large

amounts of liquids (soup making) or

fat (frying).

DO NOT use a wok if it is equipped

with a metal ring that extends beyond

the burner unit. Because this ring

traps heat, the surface unit and

cooktop surface could be damaged.

Wire trivets: Do not usewire trivets. Cookware bottoms must be in direct contact

with the grates.

DO NOT usetwo burner units to heat one large pan such asa roaster

or griddle, or allow cooking utensils to boil dry. The bottom surface of the pan in

either of these situations could cause discoloring or crazing of the appliance cooking

surface, and damage to the grates and burner units.

Canning Tips &

Information

Canning can generate

largeamounts of steam. Useextreme cau-

tion to prevent burns. Always raise the

lid to vent steam away from you.

(-:,

1. Use tested recipes and follow instructions carefully. Check with your local

Cooperative Agricultural Extension Service or a manufacturer of glassjars for

the latest canning information.

2. Useflat-bottomed canners only. Heat isspread more evenly when the bottom

surface isflat.

3. Center canner on the burner grate.

4. Startwith hotwater and a high heat setting to reduce the time ittakesto bring

the water to a boil; then reduce the heat setting as low as possible to maintain

a constant boil.

5. It is best to can small amounts and light loads.

Prevent damage to cooktop and burner grates:

1. Do not use water bath or pressure canners that extend more than one inch

beyond the edge of the burner grate.

2. Do not leave water bath or pressure canners on high heat for an extended

amount of time.

3. Alternate surface units between each batch to allow the units and surrounding

surfaces to cool down. Tryto avoid canning on the same burner unit all day.

Safecanning requires that harmful micro-organisms are destroyed

and the jars are sealed completely. When canning in a water bath canner, a gentle

but steady boil must be maintained continuously for the required time.

Liquefied Petroleum (Propane) Gas Conversion

The cooktop can be used with Natural Gasor Propane Gas. It isshipped from the factory for usewith natural gas.

If you wish to convert your appliance for usewith LP/Propane gas, usethe supplied fixed orifices located in a bag containing the

literature marked, "FORLP/PROPANEGAS CONVERSION". Follow the instructions package with the orifices.

The conversion must be performed by a qualified service technician in accordance with the manufacturer's instructions and all

codes and requirements of the authority having jurisdiction. Failureto follow instructions could result in serious injury or property

damage. The qualified agency performing this work assumes responsibility for the conversion.

Severeshock or damage to the appliance may occur if the appliance is not installed by a qualified installer.

Flame Size

For most cooking, start on the highest control setting and then turn to a lower one to complete

the process. Usea chart below asa guide for determining proper flame size for various types of

cooking. The sizeand type of utensil used and the amount of food being cooked will influence

the setting needed for cooking.

Fordeep fatfrying, usea thermometer and adjust the surface control knob accordingly. If the

fat istoo cool, the food will absorb the fat and be greasy.If the fat istoo hot, the food will brown

so quickly that the center will be undercooked. Do not attempt to deep fat fry too much food at

once asthe food will neither brown or cook properly.

*Flame size

High Flame

Medium Flame

Low Flame

Type of Cooking

Start most foods; bring water to a boil; pan broiling.

Maintain a slow boil; thicken sauces, gravies; steam.

Keep foods cooking; poach; stew.

* These settings are based on using medium thickness aluminum pans with lids. Set-

tings may vary when using other types of pans.

Never extend the flame

beyond the outer edge of the

utensil. A higher flame simply

wastes heat and energy, and

increases your risk of being

burned by the flame.

WRONG

Proper Burner Adjustments

The color of the flame isthe key to proper burner adjustment. A good flame isclear, blue and hardly visible in a well-lighted room.

Eachcone of flame should be steady and sharply defined. Adjust or clean burner if flame isyellow-orange. Toclean burner, see

instructions under General Cleaning.

Setting Surface Controls

Eachburner lights automatically from an electric ignitor each time a control knob isturned to

the lite position.

To operate the surface burner:

1. Placecooking utensil on burner.

2. Push in and turn the Surface Control knob to LITE.Note: All electronic ignitors will click

at the same time. However, only the burner you are turning on will ignite.

3. Visually check that the burner has lit.

4. After the burner lights, turn the control knob to the desired flame size.The control knobs

do not have to be set at a particular mark. Usethe guides and adjust the flame asneeded.

DO NOT cook with the control knob in the LITE position. (The electronic ignitor will

continue to click if left in the LITEposition.)

5. Toturn the burner off, turn the control knob asfar as it ill go, to the OFFposition.

The surface control knobs

shown below may not look iden-

tical to the Surface Controls

Knobs on your range; They are

only representational.

In the event of an electrical power outage, the surface burners can be lit manually. To light a

surface burner, hold a lit match to the burner head, then slowly turn the surface control knob to LITE.Usecaution when lighting

surface burners manually.

Surface burner in usewhen an electrical power failure occurs will continue to operate normally.

Do not operate the burner for an extended period of time without cookware on the grate. The finish on

the grate may chip without cookware to absorb the heat.

Do not place plastic items such as salt and pepper shakers, spoon holders or plastic wrappings on top

of the cooktop when it isin use. These items could melt or ignite. Pot holders, towels or wood spoons could catch fire if placed

too close to a flame.

Before Setting Oven Controls

Oven Vent Location

The oven is vented at the rear of the cooktop. When the oven is on, warm air is released through the vents. This venting is

necessaryfor proper air circulation in the oven and good baking results. DO NOT block the vents. Doing so may cause cooking

failures, fire or damage to the appliance

Arranging Oven Racks

ALWAYSARRANGEOVENRACKSWHEN THEOVENISCOOL(PRIORTOOPERATING

THEOVEN). Always use oven mitts when using the oven.

To remove an oven rack, pull the rack forward until it stops. Lift up front of rack

and slide out.

To replace an oven rack, Fit the rack onto the guides on the oven walls. Tilt the

front of the rack upward and slide the rack back into place.

Setting Oven Controls

Foroven settings, refer to the time or the electronic oven control section.

Before Setting Warmer Drawer Controls (somemodels)

Arranging Warmer Drawer Rack Positions

Setthe warmer drawer rack in the vertical position asshown below:

The rack can be used in 2 ways:

• In the upright position to allow low profile food items to be placed

both under and on top of the rack (for example, rolls or biscuits on

top of the rack and a casserole dish under).

• In the Downward position to allow you to place light weight food

items and empty dishware (for example, rolls or pastries and din-

ner plates).

Upright Position Downward Position

Setting Warmer Drawer Controls (somemodels)

Note: Thewarmer drawer cannot be used during an oven self-cleaning cycle. Thewarmer drawer isequipped with a catch which

may require extra force when opening and closing the drawer.

Use the warmer drawer to keep hot foods hot such as: vegetables, gravies, meats, casseroles, biscuits and rolls, pastries and

heated dinner plates.

To Operate the Warmer Drawer

The purpose of the warmer drawer is to keep hot cooked foods at serving temperature. Always start with hot food. It is not

recommended to heat cold food in the warmer drawer.

All food placed in the warmer drawer should be covered with a lid or aluminum foil to maintain moisture and softness. Do not

cover crisp foods. Do not use plastic wrap to cover food. Plastic may melt onto the drawer and be very difficult to

clean.

Useonly dishware, utensils and cookware recommended for oven use in the warmer drawer.

Always use potholders or oven mitts when removing food from the warmer drawer as cookware and plates will

be hot.

Indicator Light

The indicator light islocated above or below the thermostat control knob. It turns on when the control isset, and stayson until the

control isturned off. Make sure indicator light isoff when removing food from drawer.

To Set the Thermostat Control

The thermostat control knob is used to select the temperature of the warmer drawer. It is located at the left side of the oven

control. The temperatures are approximate, and are designated by HI, MED and LO.The control can be set to the three settings,

or anywhere between.

WARM & SERVE

DRAWER

1. Toset the thermostat, push in and turn the knob to the desired setting.

2. For best results, preheat the drawer before adding food. An empty drawer will reach the LOsetting

in about 12 minutes, the MED setting in about 15 minutes, and the HI setting in about 18 minutes.

3. When done, turn the thermostat control to OFF.

Setting Warmer Drawer Controls (some models, continued)

Temperature Selection

Referto the chart in the side column for recommended settings. If a particular food is not listed, start with the medium setting. If

more crispness isdesired, remove the lid or aluminum foil. Most foods can be kept at serving temperatures by using the medium

setting. When a combination of foods are to be kept warm (for instance, a meat with 2 vegetables and rolls), usethe high setting.

Refrain from opening the warmer drawer while in useto eliminate lossof heat from the drawer. Open only for adding or removing

food.

Warmer Drawer Recommended Food Settings Chart

Food Item Setting

Bacon HI

Biscuits M ED

Casseroles MED

Eggs MED

Empty Dinner Plate LO

Fish, Seafood MED

Fried Foods HI

Gravies MED

Food Item Setting

Ham MED

Hamburger Patties HI

Pancakes, Waffles HI

Pastries MED

Pies MED

Pizza HI

Pork Chops HI

Food Item Setting

Potatoes (baked) HI

Potatoes (mashed) MED

Poultry HI

Roast (Beef, Pork, Lamb) MED

Rolls, soft LO

Rolls, hard MED

Vegetables MED

Convection Cooking (somemodels)

NOTE: The convection fan automatically turns off when the oven door isopened while oven is in a convection mode

and resumes when the door is closed again.

The convection oven usesa fan located in the rear wall of the oven to circulate heated air around the food to be cooked. The

controlled air flow pattern quickly sealsthe food surface retaining the natural juices and flavor. This method of cooking enablesyou

to obtain the best culinary results when baking, thawing, dehydrating and roasting foods.

Convection notes:

1. Most recipes can be made with temperatures set at 13°C (25°F) lower than temperatures required for normal radiant cooking

methods. Refer to the electronic oven control operating instructions included in section "Electronic Oven Control". This can

result in considerable reduction of food shrinkage and more tender meats.

2. Batch cooking is more convenient with better results.

3. Defrosting isquicker in convection mode when compared to regular radiant cooking.

4. Remember to use tested recipes with times adjusted for convection baking/roasting when using the convection mode. Times

may be reduced by as much as 30% when using the convection feature.

Convection Roasting (somemodels)

When convection roasting, usethe broiler pan and grid, and the roasting rack.The broiler pan

Roasting will catch grease spills and the grid will help prevent grease spatters. The roasting rack will

hold the meat.

1. Placeoven rack on bottom or next-bottom rack position.

Grid

2. Placethe grid in the broiler pan. The roasting rack fits on the grid allowing the heated air to

circulate under the food for even cooking and helpsto increase browning on the underside.

Make sure the roasting rack is securely seated on the grid in the broiler pan. DO NOT use

the broiler pan without the grid or cover the grid with aluminum foil.

Broiler

Speed Bake TM Cooking System (somemodels)

Speed BakeTM Cooking System uses a fan to circulate the oven's heat uniformly and

continuously around the oven. This improved heat distribution allows for fast, even cooking and

browning results. It also gives better baking results when using two racks at the same time.

Heated air flows around the food from all sides,sealing in juices and flavors. Meats cooked with

Speed BakeTM Cooking System arejuicer. Poultry iscrisp on the outside while staying tender and

moist on the inside. Breadsand pastry brown more evenly. Most foods baked in a standard oven

can be cooked faster and more evenly with Speed BakeTM Cooking System.

Benefits of Speed Bake TM Cooking System:

Foods cook up to 30% faster, saving time and energy.

Two racks can be used with more even cooking and browning.

No special pans or bakeware needed.

General Cooking Instructions:

1. To convert baking times from normal recipes to Speed Bake times, start with a 30%

reduction in time and increase the time until desired doneness isobtained. Time reductions

will vary depending on the amount and type of food.

2. Preheating is not necessary when cooking with Speed Bake, except with items such as

cakes, cookies, biscuits, breads, etc.

3. When using two racksat the same time, place them in positions 1 and 3 for the best results.

4. When baking cakeswith Speed Bake, set temperature 25°F (13°C) degrees lower than the

recommended setting for best results.

To Set Speed Bake TM Cooking System:

1. Program the oven asyou normally would for baking. Speed Bake may be used with Bake, Time Bake and Delayed Time Bake

modes.

2. Push and releases Speed Bake switch. The indicator light will glow and the fan will come on. The fan

stays on when oven door isclosed and shuts off while the oven door isopened. The fan will continue to

operate until baking iscomplete, o

3. When using Speed Bake feature along with the Delayed Timed Bake mode, the fan will begin to operate L Pilot

when the control is set. The oven elements will not begin to operate until the Delayed Start Time is light

reached. This operation isnormal.

4. To cancel Speed Bakefunction, push CANCEL on the oven control asyou would to cancel any baking function.

Note: Speed Bake mode will not work during a clean cycle.

Food Item Decrease Cook Time by:

Casseroles 25%

Meats 15% (or 5 mins/pound)

Poultry 30% (or 10 mins/pound)

Frozen Foods 20%

Refrigerator Cookies or Biscuits 25% (or 2 to 5 min.)

Rolls/Breads/Pizza 25% (or 5 min.)

Vegetables 25%

Baked potatoes 25%

Pies/Pastries 30%

Oven Baking

Forbest cooking results, heat the oven before baking cookies, breads, cakes, pies or pastries, etc... There is no need to preheat

the oven for roasting meat or baking casseroles.

The cooking times and temperatures needed to bake a product may vary slightly from your previously owned appliance.

Baking Problems

Cookies and biscuits

burn on the bottom.

Cakes too dark on top

or bottom.

Cakes not done in the

center.

Cakes not level.

Foods not done when

cooking time is up.

Baking Problems and Solutions Chart

Causes Corrections

• Cookies and biscuits put into the

oven before the preheating time is

completed.

• Oven rack overcrowded.

• Dark pan absorbs heat too fast.

• Cakes put into the oven before

preheating time is completed.

• Rack position too high or low.

• Oven too hot.

• Incorrect pan size.

• Pan not centered in oven.

• Range not level.

• Pan too close to oven wall or rack

overcrowded.

• Pan warped.

• Oven too cool.

• Oven overcrowded.

• Oven door opened too frequently.

• Allow oven to preheat to the selected temperature before

placing food in oven.

• Choose pan sizesthat will permit 5.1 cm to l 0.2 cm (2" to 4") of

air space on all sides when placed in the oven.

• Use a medium-weight aluminum baking sheet.

• Allow oven to preheat to the selected temperature before

placing food in the oven.

• Use proper rack position for baking needs.

• Set oven temperature 25°F/12°C lower than recommended.

• Use pan size suggested in recipe.

• Use proper rack position and place pan so there is 5.1 cm to

10.2 cm (2" to 4") of space on all sides of pan.

• Place a marked glass measuring cup filled with water on the

center of the oven rack. If the water level isuneven, refer to the

installation instructions for leveling the range.

• Besure to allow 5.1 cm to l 0.2 cm (2" to 4") of clearance on all

sides of each pan in the oven.

• Do not use pans that are dented or warped.

• Set oven temperature 25°F/12°C higher than suggested and

bake for the recommended time.

• Besure to remove all pans from the oven except the ones to be

used for baking.

• Open oven door only after shortest recommended baking time.

Air Circulation in the

Oven

For good air circulation in the oven and

best baking results, center pans as much as

possible. Allow 5.1 to 10.2 cm (2" to 4")

around the utensil(s) for proper air circula-

tion and be sure pans do not touch each

other, the door, sides or back of oven. The

hot air must circulate around the pans for

even heat to reach all parts of the oven.

If using multiple pans, stagger asshown. If using one pan, place in center of oven.

Broiling

Broiling isa method of cooking tender cuts of meat by direct heat under the broil element of the oven.

Open door

to the "Broil Stop"

position when broiling.

Always pull oven rack out

to the "stop" position be-

fore turning or removing

food.

Preheating

Preheating issuggested when searing rare steaks. (Remove the broiler pan before preheating.

Foodswill stick if placed on hot metal.) Topreheat, set the oven control(s) to BROILas instructed

in the Owner's Guide. Wait for the element to become red-hot, usually about 2 minutes.

Preheating isnot necessarywhen broiling meats well-done.

To Broil

Broil on one side until the food isbrowned; turn and cook on the second side. Seasonand serve.

Always pull rack out to the "stop" position before turning or removing food.

Determining Broiling Times

Broiling times vary,so watch the food closely. Time not only depends on the distance from the

element, but on the thickness and aging of meat, fat content and doneness preferred. The first

side usually requires a few minutes longer than the second. Frozen meats also require additional

time.

Broiling Tips

The broiler pan and its grid allow dripping grease to drain and be kept away from the high heat

of the broiler.

DO NOT use the pan without its grid. DO NOT cover the grid with foil. The exposed

grease could ignite.

Should an oven fire occur, close the oven door and turn off the oven. If the fire

continues, throw baking soda on the fire or usea fire extinguisher. DO NOT put water or flour on

the fire. Flour may be explosive.

Broiler Pan

Broiler Clean-Up Tips:

• To make cleaning easier, line the bottom of the broiler pan with aluminum foil. DO NOT cover the broiler grid with foil.

• To prevent grease from baking on, remove the broiler pan from the oven as soon as cooking is completed. Use hot pads

because the broiler pan is extremely hot. Pour off grease. Soak the pan in HOT,soapy water.

• Clean the broiler pan as soon as possible after each use. If necessary, use soap-filled steel wool pads. Heavy scouring may

scratch the grid.

General Cleaning

Cleaning Various Parts of Your Range

Before cleaning any part of the range, be sure all controls are turned OFFand the range is COOL. REMOVESPILLOVERSAND

HEAVY SOILINGAS SOON AS POSSIBLE.REGULARCLEANING WILL REDUCETHE NUMBER OF MAJOR CLEANING LATER.

Surfaces

Aluminum & Vinyl

Control Panel and Trim Pieces

Glass, Painted and Plastic

Control Knobs, Body Parts,and

Decorative Trim

Stainless Steel (some mod-

els) Oven Door & Drawer Front

Panel

Sealed Burner Units

Burner Cap, Trim Ring (some

models), Burner Pans(some

models), and Burner Base

Porcelain Enamel

Burner Grates

Cooktop, Broiler Pan and Insert,

Door Liner, Body Parts and

Warmer Drawer and Drawer

Cavity

How to Clean

Use hot, soapy water and a cloth. Dry with a clean cloth.

Before cleaning the controlpanel, turn all controls to OFFand remove the control knobs. To

remove, pull each knob straight off the shaft. Clean using hot, soapy water and a dishcloth.

Rinsewith a clean water and a dishcloth. Cover stubborn spots with an ammonia-soaked

paper towel for 30 to 40 minutes. Rinse. Be sure to squeeze excesswater from the cloth

before wiping the panel; especially when wiping around the controls. Excesswater in or

around the controls may cause damage to the appliance. Be sure to rinse the cleaners as

bluish stains may occur during heating and cannot be removed. To replace knobs after

cleaning, line up the flat sides of both the knob and the shaft; then push the knob into

place.

For general cleaning, use hot, soapy water and a cloth. For more difficult soils and built-up

grease, apply a liquid detergent directly onto the soil. Leave on soil for 30 to 60 minutes.

Rinsewith a damp cloth and dry. DO NOT use abrasive cleaners on any of these materials;

they can scratch. To remove control knobs, turn to the OFFposition; grasp firmly and pull

straight off the shaft. Toreplace knobs after cleaning, line up the flat sides of both the knob

and the shaft; then push the knob into place.

Cleaners made especially for stainless steel as Stainless Steel Magic, or other similar

cleaners are recommended. Always follow the manufacturer's instructions. Besure to rinse

the cleaners asbluish stains may occur during heating and cannot be removed.

The holes in the burner of your range must be kept clean at all times for proper ignition and

a complete, even flame. Clean the burners routinely and especially after bad spillovers

which could clog these holes.

To remove, clean and replace the entire burner cap assembly,follow the instructions under

General Cleaning. DO NOT put burner parts in the dishwasher.

Gentle scouring with a soapy scouring pad will remove most spots. Rinsewith a 1:1 solution

of clear water and ammonia. If necessary, cover difficult spots with an ammonia-soaked

paper towel for 30-40 minutes. Rinsewith clear water and damp cloth, and then scrub with

a soap-filled scouring pad. Rinseand wipe dry with a clean cloth. Remove all cleaners or the

porcelain may become damage during future heating. DO NOT usespray oven cleaners on

the rangetop.

General Cleaning (continued)

To Clean the Tempered-glass Cooktop (somemodels)

Unlike the standard gas range, THIS COOKTOP ISNOT REMOVABLE. Do not attempt to remove or lift the cooktop.

Before cleaning the cooktop, be sure the controls are turned to OFF and the cooktop is COOL.

DO NOT usea cooktop cleaner on a hot cooktop. The fumes can be hazardous to your health, and can chemically

damage the ceramic- glasssurface. Besurethe controls are turned to OFF. Do not use commercial oven cleaners on any part

of the cooktop. Damage to the finish or parts could result.

The cooktop is designed to make cleaning easier. Because the four burners are sealed, cleanups are easy when spillovers are

cleaned up immediately. Toclean, wipe with a clean, damp cloth and wipe dry.

Correct and consistent cleaning is essential to maintaining your heat-resistant glass top. Spills and

spatters should be wiped up using a clean paper towel and sudsywater. This should be done either as

soon as possible after spill occurs, after cooking iscompleted, or at the latest, before usingthe cooktop

again. Use caution if the cooktop is hot. For heavy spills, spatter or burned-on materials, use razor

blade scraper. Hold the razor blade scraper at a 30° angle and remove food spills or burned on food

residue.

For sugary spillovers:

Sugary spills can cause pitting of your cooktop surface. Therefore, you must begin cleaning the spills

while the cooktop isstill hot.

Finish the cleaning process by applying a recommended heat- resistant glass cooktop deaning

cream. Apply cleaner with clean, damp paper towel. Rinse with a paper towel dampened with clean

water and wipe dry. Always wipe the cooktop thoroughly to avoid heating any cleaner residue.

witharazorbladescraper.Use

cautionto avoiddamaging

surface.

Do NOT use the following on the heat-resistant glass cooktop:

Abrasive plastic, nylon, metal scouring or cloth pads. They may scratch the cooktop and make it more difficult to clean later.

Always usea new, clean paper towel when cleaning the heat-resistant glass top.

Anything that may melt (plastics, aluminum foil, sugar or food with a high sugar content).

Heavy duty cleansers, rust or stain removers.

Chlorine bleach, ammonia, hydrofluoric acid or any other kind of chemical cleaners. They may etch or discolor the cooktop.

Sponges, cloths or dish towels. Always use a new, clean paper towel when cleaning the cooktop. Lint or soil remaining on the

cooktop from a cloth or sponge can burn and cause discoloration.

To Clean the Burner Grates, Contoured Burner Pans, Burner Cap and Burner Base

The burner grates, contoured burner pans, burner caps and burner base should be routinely cleaned. Keeping the burner ports

clean will prevent improper ignition and an uneven flame. Seeinstructions below.

To Clean the Burner Grates

Be sure burners and grates are cool before you place your hand, a pot holder,

cleaning cloths or other material on them. The cast iron burner grates can be washed in

hot soapy water. Rinsethoroughly and dry the grates with a cloth - don't put them on the

cooktop while still wet. Besure the grates are positioned securely over the burners.

Toremove burned on food, place the grates in a covered container or plastic bag. Add 1/

4 cup ammonia and soak for 30 minutes. Wash, rinse well and dry. An abrasive cleaner

can be usedfor stubborn stains.

To Clean the Contoured Burner Pans

The burner pans are attached to the cooktop and are not removable. The burner pan

forms a recessedwell area located around each burner unit. If spill occurs in one of the

well areas, blot up spill with an absorbent cloth. Rinsewith a clean, damp cloth and wipe

dry.

Burner grate can appear in different

shapes.

General Cleaning (continued)

To Clean the eurner Grates, Contoured eurner Pans, eurner Cap and eurner ease (continued)

To Clean the euner Cap

Remove burner cap. Usa soap-filled pad or mild abrasive cleanser to clean burner caps. If necessary,cover stubborn spots with

ammonia-soaked paper towel for minutes. Rub gently with a mixture of clean water and vinegar. Wipe dry. Removeall cleaners or

the porcelain may become damaged during future heating.

Burner Cap

Sealed Burner

To Clean the Removable Burner Baseand Gas Opening (some models)

The ports (or slots) around the burner base must be routinely cleaned. Usea small-

gauge wire or needle to clean small slots or holes.

Note: If the electrode is damaged or broken, the surface burner will not light

because it will not spark. Manual lighting with a match isstill possible.

For proper flow of gas and ignition of the burner - DO NOT ALLOW SPILLS,FOOD,

CLEANING AGENTS OR ANY OTHER MATERIAL TO ENTERTHE GAS OPENING

TUBE.Gasmust flow freely through the small hole in the brassorifice for the burners

to light properly. If the gas opening orifice becomes soiled or clogged, usea small-

gauge or needle to clean. ALWAYSkeep the burner cap in place whenever a surface

burner isin use.

To Replace the Burner Base and the Burner Cap

Make sure the pieces are thoroughly dry before placing back.

1. Replace burner base and burner cap at there place. Make sure each burner cap

and burner baseare properly aligned and leveled.

2. Replace the burner grate.

3. Turn the burner on to determine if it light. If the burner does not light after

cleaning, contact an authorized servicer. Do not service the sealed burner

yourself.

Cleaning the Self-Clean Oven (some models)

Adhere to the following cleaning precautions:

Allow the oven to cool before cleaning.

Wear rubber gloves when cleaning any exterior parts of the oven manually.

During the self-clean cycle, the outside of the wall oven can become very hot to the touch. DO NOT leave small

children unattended near the appliance.

The health of some birds isextremely sensitive to the fumes given off during the self-cleaning cycle of any range.

Move birds to another well ventilated room.

Before cleaning any part of the oven, be sure the electronic oven control isturned off or else push CANCEL pad.

Wait until the oven iscool.

DO NOT use commercial oven cleaners or oven protective coatings in or around any art of the self-cleaning oven. DO NOT clean

the oven door gasket. The gasket on the oven door isessential for a good seal. Care should be taken not to rub, damage or move

the gasket. DO NOT cooking or foil could melt and damage the oven surface.

A self-cleaning oven cleans itself with high temperatures (well above cooking temperatures) which eliminate soil completely or

reduce it to a fin powdered ash you can which away with damp cloth.

General cleaning (continued)

Cleaning the Self-Clean Oven (somemodels,continued)

Do Hand

Clean

Frame

Preparing the Oven for Self-Cleaning

1. Remove all excess spillovers in the oven cavity before starting the self-cleaning

cycle. Toclean, usehot soapy water and a cloth. Large spillovers can cause heavy

smoke or fire when subjected to high temperatures. DO NOTallow food spillswith

a high sugar or acid content (such as tomatoes, sauerkraut, fruit juices or pie

filling) to remain on the surface asthey may cause a dull spot even after cleaning.

2. Clean any soil from the oven frame and the door liner (see illustration). These

areas heat sufficiently during self-cleaning cycle to burn soil on. Clean with soap

and water.

3. Remove the broiler pan and insert, all utensils and any foil. These items do not

withstand high cleaning temperatures

4. Oven racks may be left in the oven or may be removed. If they go through the

clean cycle, their color will turn slightly dull. After the cycle iscompleted and the

oven hascooled, rub the sides of the rackswith wax paper or a cloth containing a

small amount of baby oil or salad oil. This will make the racks glide easier.

Do Hand Do Not Hand

Clean Door Clean Seal

What to Expect During Cleaning

While the oven is in operation, the oven heats to temperatures much higher than those used in normal cooking. Sounds of metal

expansion and contraction are normal. Odor isalso normal asthe food soil isbeing removed. Smoke may appear through the oven

vent, located on the top of the control panel.

If heavy spillovers are not wiped up before cleaning, they may flame and cause more smoke and odor than usual. This is normal

and safe and should not cause alarm. If available, use an exhaust fan during the self-cleaning cycle.

NOTE: A smoke eliminator in the oven vent converts most of the soil into a colorless vapor.

Setting the Controls for Self-Clean Cycle

Forthe setting of the clean cycle, refer to Timer or Electronic Oven Control section.

To Remove and Replace Oven Door

1. Open the door to the fully opened position.

2. Pullup the lock located on both hinge supports and engage it in the hook of the hinge levers. You may haveto apply a

little downward pressure on the door to pull the locks fully over the hooks.

3. Grab the door by the sides, pull the bottom of the door up and toward you to disengage the hinge supports.

Keep pulling the bottom of the door toward you while rotating the top of the door toward the range to completely disen-

gage the hinge levers.

4. Proceed in reverse to reinstall the door.

Make sure the hinge supports are fully engaged before unlocking the hinge levers.

The door is heavy. Forsafe, temporary storage, laythe door flat with the inside of the door facing down.

Lock in normal position

Lock engaged

for door removal

HINGE SLOT Door re-

moved from the range

General Cleaning (continued)

Removable Outer Door Glass Panel (some models)

Applicable only to models with an external glass panel not held with a frame. This design allows you to clean the insideface of the

exterior door panel aswell asthe hidden face of the door inner glass.There are two different kinds of glass panel; one with a lower

metal trim fixed on the underside of the glass panel and the other one with a lower metal support rail.

To remove the external door glass panel:

1. Pull the door off the range as per instructions under "To Remove and Replace Oven Door" in "Cleaning the Appliance"

section and lay the door flat.

2. Using a screwdriver, remove the screws fastening the glass lower metal trim or the glass assembly.

3. Grab both sides of the glass panel and slowly pull it out of the door upper moulding. Laythe glass flat.

Handle the glass panel with care. When dropped on a corner the glass panel may shatter in multiple fragments and

you could get hurt.

DO NOT remove the lower metal trim, which isfixed on the underside of the glass panel.

To replace the external door panel:

1. Grab the sidesof the glass panel and carefully insert the glass into the door top moulding.

2. Replace the glass lower trim or the glass assembly using the locking screws.

3. Replace the door onto the range as per "To Remove and Replace Oven Door" in "Cleaning the Appliance" section.

To Remove and Replace

Left Glide _ Pull up latch

Push down latch Right Glide

with finger

Warmer Drawer

Warmer Drawer (some models)

To remove Warmer Drawer

1. _ Turn power off before removing the warmer drawer.

2. Open the drawer to the fully opened position.

3. Locate the latches on both sides of the warmer drawer.

4. Pull up on the left glide latch and push down on the right glide latch.

5. Pull the drawer away from the range.

6. Toclean warmer drawer, gently scour with a soapy scouring pad, this will remove most spots.

Rinsewith a 1:1 solution of clear water and ammonia. If necessary,cover difficult spots with

an ammonia-soaked paper towel for 30 to 40 minutes. Rinsewith clean water and a damp

cloth. Removeall cleaners or the porcelain may become damaged during future heating. DO

NOT use spray oven cleaners on the cooktop.

To Replace Warmer Drawer:

1. Align the glide latches on both sides of the drawer with the slots on the drawer.

2. Pushthe drawer back into the range.

I_l _ Electrical Shock Hazard can occur and result in serious injury or death. Disconnect appliance from

electric power before cleaning and servicing the warmer drawer.

General Cleaning (continued)

Storage Drawer (some models)

Usethe storage drawer for storing cooking utensils. The drawer can de removed to facilitate cleaning under the range. Usecare

when handling the drawer.

Toopen the storage drawer, push the drawer in gently and it will spring open. Toclose, push the drawer until you hear a click,

which indicates that the spring iscompressed, and the drawer isclosed.

Frame

Storage

Drawer

To remove the drawer:

1. Pull empty drawer out to the roller guide stop.

2. Tilt the drawer up and pull it out over the rollers.

To replace the drawer:

1. Insertthe rear end of the drawer into the opening.

2. Fitthe drawer end rollers onto the guide rails.

3. Pushthe drawer in until it stops, then lift to allow the rollersto clearthe roller guide stop,

and push in.

Changing Oven Light

Besurethe oven is unplugged and all parts are COOLbefore replacing the oven light bulb. Do not turn the oven

light on during the self-cleaning cycle. High temperature will reduce lamp life.

On some models an interior oven light will turn on automatically when the oven door isopened.

The oven light may be turned on when the door isclosed by using the oven light switch located on the control panel.

On a self clean oven the lamp is covered with a glass shield held in place by a wire holder.

THIS GLASS SHIELD MUST BEIN PLACEWHENEVER THE OVEN IS IN USE.

To replace the light bulb:

CAUTION: BESUREOVEN ISCOOL

1. Turn the power off at the main source.

2. Wear a leather-faced glove for protection against possible broken glass.

3. Replace bulb with a 40 watt appliance bulb only.

4. Forself-cleaning oven, presswire holder to one side to releaseglass shield, change bulb and be

sure to replace glassshield.

Avoid Service Checklist

Before you call for service - read this

You may savethe cost and inconvenience of an unnecessary service call by first reviewing this easy to use Avoid-Service Check List

of the most frequently encountered situations that are not the result of defective workmanship of materials.

You will be charged for a service call while the appliance is in warranty if the problem is not caused by defective product

workmanship or materials.

Your new appliance isa carefully engineered product. Many times, what appears to be a reasonto call for service requires nothing

more than a simple adjustment you can easily make in your own home or is normal operating characteristic of appliance under

certain conditions.

This list is applicable to a variety of models; some of the items will not necessarily apply to your appliance.

PROBLEM POSSIBLE CAUSE/SOLUTION

INSTALLATION

Range is not level.

Poor installation. Placeoven rack in center of oven. Adjust leveling legs(slide-in models) at

baseof range until the oven rack is level.

Besure floor is leveland isstrong and stable enough to adequately support range.

Avoid Service Checklist (continued)

PROBLEM POSSIBLECAUSE/SOLUTION

INSTALLATION (continued)

Range is not level. If floor issagging or sloping, contact a carpenter to correct the situation.

Kitchen cabinet alignment may make range appear unlevel. Be sure cabinets are square

and have sufficient room for range clearance.

Cannot move appliance easily.Ap-

pliance must be accessible for

service.

Cabinets not square or are built in too tightly. Contact builder or installer to make appliance

accessible.

Carpet interferes with range. Provide sufficient space so range can be lifted over carpet.

RANGE DOES NOT OPERATE

Entire range or oven does not

operate.

Make sure cord/plug isplugged tightly into outlet.

Service wiring is not complete. Contact your dealer, installing agent or authorized servicer.

Power outage. Check house lights to be sure. Call your local electric company for service.

Oven does not operate. Oven control beeps and displays -F1-, -F3- or -F9-. Electronic control has detected a fault

condition. Pushthe CANCEL pad to clear the display and stop the beeping. Reprogram

oven. If fault recurs, record fault number, push CANCEL pad and contact authorized

servicer.

Oven light does not work. Replaceor tighten bulb. See Changing Oven Light in this Owner's Guide for instructions.

Surface unit does not heat. No power to the appliance. Check steps under "Entire Appliance Does Not Operate" in this

Avoid Service CheckList.

Incorrect control setting. Make sure the correct control ison for the surface unit to be used.

SURFACE UNITS

Surface units too hot or not hot

enough.

Incorrect control setting. Make sure the correct control ison for the surface unit to be used.

Lightweight or warped pans used. Useonly flat, evenly balanced, medium or heavyweight

cookware. Flat pans heat better than warped pans. Cookware materials and weight of the

material affect heating. Heavy-and medium- weight pans heat evenly. Because lightweight

pans heat unevenly, foods may burn easily.

Drip bowls are pitting or rusting. Foods with acids, such astomatoes, if allowed to stand in/on bowls will cause corrosion.

Removeand wash drip bowls as soon aspossible after spillover.

Normal environment. Housesalong seacoast are exposed to salt air. Protect bowls as much

as possible from direct exposure to salt air.

Drip bowls turning color or dis-

torted out of shape.

Bottom surface of cookware extends beyond surface elements and touches cooktop

surface. This can cause high enough temperatures to discolor the drip bowls. DO NOTuse

cookware of this type. Pan sizes should be matched to the size of the element.

Replacement drip bowls may be purchased from your dealer.

Page is loading ...

Frigidaire GLCS376CBA Owner's manual

Brand: Frigidaire

Model: GLCS376CBA

Category: Cookers

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Frigidaire GLCS376CBA Owner's manual

This manual is also suitable for

Frigidaire GLCS376CBA Owner's manual

Related papers

Other documents