Chicago Electric 5 Amp Heavy Duty Tool_Free Variable Speed Orbital Jig Saw Owner's manual

Brand: Chicago Electric

Model: 5 Amp Heavy Duty Tool_Free Variable Speed Orbital Jig Saw

Category: Power tools

Type: Owner's manual

This manual is also suitable for

Visit our website at: http://www.harborfreight.com

Email our technical support at: [email protected]

ORBITAL

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

2014 by Harbor Freight Tools

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product

described herein. Tools required for assembly and service may not be included.

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-888-866-5797 as soon as possible.

Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,

inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual

near the assembly diagram (or month and year of purchase if product has no number).

Keep this manual and the receipt in a safe and dry place for future reference.

Owner’s Manual & Safety Instructions

REV 14g

(Blade sold separately)

Page 2 For technical questions, please call 1-888-866-5797. Item 62422

Important Safety Information

In this manual, on the labeling, and all other

information provided with this product:

This is the safety alert symbol.

It is used to alert you to potential

personal injury hazards. Obey

all safety messages that

follow this symbol to avoid

possible injury or death.

DANGER indicates a hazardous

situation which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazardous

situation which, if not avoided, could

result in death or serious injury.

CAUTION, used with the safety alert

symbol, indicates a hazardous situation

which, if not avoided, could result

in minor or moderate injury.

NOTICE is used to address practices

not related to personal injury.

CAUTION, without the safety alert

symbol, is used to address practices

not related to personal injury.

General Power Tool

Safety Warnings

WARNING Read all safety warnings

and instructions. Failure to follow the

warnings and instructions may result in

electric shock, fire and/or serious injury.

Save all warnings and instructions

for future reference.

The term ″power tool″ in the warnings

refers to your mains‑operated

(corded) power tool.

1. Work area safety

a. Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b. Do not operate power tools in

explosive atmospheres, such as in the

presence of flammable liquids, gases

or dust. Power tools create sparks

which may ignite the dust or fumes.

c. Keep children and bystanders

away while operating a power tool.

Distractions can cause you to lose control.

2. Electrical safety

a. Power tool plugs must match the

outlet. Never modify the plug in

any way. Do not use any adapter

plugs with grounded power tools.

Unmodified plugs and matching outlets

will reduce risk of electric shock.

b. Avoid body contact with grounded

surfaces such as pipes, radiators,

ranges and refrigerators. There is an

increased risk of electric shock

if your body is grounded.

c. Do not expose power tools to rain or

wet conditions. Water entering a power

tool will increase the risk of electric shock.

d. Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving

parts. Damaged or entangled cords

increase the risk of electric shock.

e. When operating a power tool

outdoors, use an extension cord

suitable for outdoor use. Use

of a cord suitable for outdoor use

reduces the risk of electric shock.

f. If operating a power tool in a damp

location is unavoidable, use a Ground

Fault Circuit Interrupter (GFCI)

protected supply. Use of a GFCI

reduces the risk of electric shock.

Page 3For technical questions, please call 1-888-866-5797.Item 62422

3. Personal safety

a. Stay alert, watch what you are

doing and use common sense when

operating a power tool. Do not use

a power tool while you are tired or

under the influence of drugs, alcohol

or medication. A moment of inattention

while operating power tools may

result in serious personal injury.

b. Use personal protective equipment.

Always wear eye protection. Safety

equipment such as a dust mask,

non-skid safety shoes, a hard hat, or

hearing protection used for appropriate

conditions will reduce personal injuries.

c. Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source, picking

up or carrying the tool. Carrying

power tools with your finger on the

switch or energizing power tools that

have the switch on invites accidents.

d. Remove any adjusting key or wrench

before turning the power tool on.

A wrench or a key left attached to

a rotating part of the power tool

may result in personal injury.

e. Do not overreach. Keep proper

footing and balance at all times. This

enables better control of the power

tool in unexpected situations.

f. Dress properly. Do not wear loose

clothing or jewelry. Keep your hair,

clothing and gloves away from moving

parts. Loose clothes, jewelry or long

hair can be caught in moving parts.

g. If devices are provided for the

connection of dust extraction

and collection facilities, ensure

these are connected and properly

used. Use of these devices can

reduce dust-related hazards.

h. Only use safety equipment that has

been approved by an appropriate

standards agency. Unapproved safety

equipment may not provide adequate

protection. Eye protection must be

ANSI‑approved and breathing protection

must be NIOSH‑approved for the

specific hazards in the work area.

4. Power tool use and care

a. Do not force the power tool. Use

the correct power tool for your

application. The correct power tool

will do the job better and safer at the

rate for which it was designed.

b. Do not use the power tool if the

switch does not turn it on and off.

Any power tool that cannot be

controlled with the switch is

dangerous and must be repaired.

c. Disconnect the plug from the

power source before making any

adjustments, changing accessories, or

storing power tools. Such preventive

safety measures reduce the risk of

starting the power tool accidentally.

d. Store idle power tools out of the

reach of children and do not allow

persons unfamiliar with the power tool

or these instructions to operate the

power tool. Power tools are dangerous

in the hands of untrained users.

e. Maintain power tools. Check for

misalignment or binding of moving

parts, breakage of parts and any

other condition that may affect the

power tool’s operation. If damaged,

have the power tool repaired

before use. Many accidents are caused

by poorly maintained power tools.

f. Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely

to bind and are easier to control.

g. Use the power tool, accessories and

tool bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

5. Service

a. Have your power tool serviced by

a qualified repair person using

only identical replacement parts.

This will ensure that the safety of

the power tool is maintained.

Page 4 For technical questions, please call 1-888-866-5797. Item 62422

Jigsaw Safety Warnings

1. Hold power tool by insulated gripping

surfaces when performing an operation

where cutting tool may contact hidden

wiring or its own cord. Contact with a

″live″ wire will make exposed metal parts

of the tool ″live″ and shock the operator.

2. Use clamps or another practical way

to secure and support the work piece

to a stable platform. Holding the work

by hand or against your body leaves it

unstable and may lead to loss of control.

3. Maintain labels and nameplates on

the tool. These carry important safety

information. If unreadable or missing, contact

Harbor Freight Tools for a replacement.

4. Avoid unintentional starting. Prepare to

begin work before turning on the tool.

5. Do not lay the tool down until it has come to

a complete stop. Moving parts can grab the

surface and pull the tool out of your control.

6. When using a handheld power tool,

maintain a firm grip on the tool with

both hands to resist starting torque.

7. Do not leave the tool unattended when

it is plugged into an electrical outlet.

Turn off the tool, and unplug it from

its electrical outlet before leaving.

8. This product is not a toy.

Keep it out of reach of children.

9. People with pacemakers should consult their

physician(s) before use. Electromagnetic

fields in close proximity to heart pacemaker

could cause pacemaker interference or

pacemaker failure. In addition, people with

pacemakers should:

• Avoid operating alone.

• Do not use with power switch locked on.

• Properly maintain and inspect to avoid

electrical shock.

• Any power cord must be properly

grounded. Ground Fault Circuit Interrupter

(GFCI) should also be implemented –

it prevents sustained electrical shock.

10. WARNING: The cord of this product

contains lead, a chemical known to the

State of California to cause cancer, and birth

defects or other reproductive harm. Wash

hands after handling. (California Health

& Safety Code § 25249.5, et seq.)

11. WARNING: Some dust created by power

sanding, sawing, grinding, drilling, and

other construction activities, contains

chemicals known to the State of California

to cause cancer and birth defects or other

reproductive harm. Some examples of these

chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks and cement or

other masonry products

• Arsenic and chromium from chemically

treated lumber

Your risk from these exposures varies,

depending on how often you do this type

of work. To reduce your exposure to

these chemicals: work in a well ventilated

area, and work with approved safety

equipment, such as those dust masks

that are specially designed to filter out

microscopic particles. (California Health

& Safety Code § 25249.5, et seq.)

12. The warnings, precautions, and instructions

discussed in this instruction manual cannot

cover all possible conditions and situations

that may occur. It must be understood by

the operator that common sense and caution

are factors which cannot be built into this

product, but must be supplied by the operator.

Vibration Safety

This tool vibrates during use.

Repeated or long-term exposure to

vibration may cause temporary or

permanent physical injury, particularly

to the hands, arms and shoulders. To

reduce the risk of vibration-related injury:

Page 5For technical questions, please call 1-888-866-5797.Item 62422

1. Anyone using vibrating tools regularly or for

an extended period should first be examined

by a doctor and then have regular medical

check-ups to ensure medical problems are

not being caused or worsened from use.

Pregnant women or people who have impaired

blood circulation to the hand, past hand

injuries, nervous system disorders, diabetes,

or Raynaud’s Disease should not use this tool.

If you feel any symptoms related to

vibration (such as tingling, numbness,

and white or blue fingers), seek medical

advice as soon as possible.

2. Do not smoke during use. Nicotine reduces

the blood supply to the hands and fingers,

increasing the risk of vibration-related injury.

3. Wear suitable gloves to reduce the

vibration effects on the user.

4. Use tools with the lowest vibration

when there is a choice.

5. Include vibration-free periods

each day of work.

6. Grip tool as lightly as possible

(while still keeping safe control of it).

Let the tool do the work.

7. To reduce vibration, maintain the tool as

explained in this manual. If any abnormal

vibration occurs, stop use immediately.

SAVE THESE INSTRUCTIONS.

Grounding

TO PREVENT ELECTRIC SHOCK

AND DEATH FROM

INCORRECT GROUNDING

WIRE CONNECTION:

Check with a qualified electrician if you are in

doubt as to whether the outlet is properly

grounded. Do not modify the power cord plug

provided with the tool. Never remove the

grounding prong from the plug. Do not use

the tool if the power cord or plug is damaged.

If damaged, have it repaired by a service

facility before use. If the plug will not fit the

outlet, have a proper outlet installed by a

qualified electrician.

Double Insulated Tools:

Tools with Two Prong Plugs

Outlets for 2-Prong Plug

1. Tools marked “Double Insulated” do not

require grounding. They have a special

double insulation system which satisfies

OSHA requirements and complies with

the applicable standards of Underwriters

Laboratories, Inc., the Canadian Standard

Association, and the National Electrical Code.

2. Double insulated tools may be used in either

of the 120 volt outlets shown in the preceding

illustration. (See Outlets for 2-Prong Plug.)

Page 6 For technical questions, please call 1-888-866-5797. Item 62422

Extension Cords

1. Grounded tools require a

three wire extension cord.

Double Insulated tools can use either

a two or three wire extension cord.

2. As the distance from the supply outlet

increases, you must use a heavier gauge

extension cord. Using extension cords

with inadequately sized wire causes a

serious drop in voltage, resulting in loss

of power and possible tool damage.

(See Table A on page 6.)

3. The smaller the gauge number of the wire,

the greater the capacity of the cord. For

example, a 14 gauge cord can carry a higher

current than a 16 gauge cord. (See Table A.)

4. When using more than one extension cord

to make up the total length, make sure

each cord contains at least the minimum

wire size required. (See Table A.)

5. If you are using one extension cord for more

than one tool, add the nameplate amperes

and use the sum to determine the required

minimum cord size. (See Table A.)

6. If you are using an extension cord

outdoors, make sure it is marked with the

suffix “W-A” (“W” in Canada) to indicate

it is acceptable for outdoor use.

7. Make sure the extension cord is

properly wired and in good electrical

condition. Always replace a damaged

extension cord or have it repaired by a

qualified electrician before using it.

8. Protect the extension cords from

sharp objects, excessive heat,

and damp or wet areas.

TABLE A: RECOMMENDED

MINIMUM WIRE GAUGE FOR

EXTENSION CORDS* (120/240 VOLT)

NAMEPLATE

AMPERES

(at full load)

EXTENSION CORD

LENGTH

25´

50´

75´

100´

150´

5.1 – 7.0 18 16 14 12 12

7.1 – 12.0 18 14 12 10 -

12.1 – 16.0 14 12 10 - -

16.1 – 20.0 12 10 - - -

* Based on limiting the line voltage drop to

ve volts at 150% of the rated amperes.

Symbology

Double Insulated

Canadian Standards Association

Underwriters Laboratories, Inc.

VAC

Volts Alternating Current

Amperes

WARNING marking concerning Risk

of Eye Injury. Wear ANSI-approved

safety goggles with side shields.

Read the manual before

set-up and/or use.

WARNING marking concerning

Risk of Electric Shock.

Properly connect power cord

to appropriate outlet.

Page 7For technical questions, please call 1-888-866-5797.Item 62422

Specifications

Electrical Rating 120VAC / 60Hz / 5A

Cutting Speed 0-3000 SPM

Stroke Length 3/4″

Max. Capacity 2-1/4″ (wood)

Footplate Tilt 0-45°, left or right

Blade Type T-Shank

4006094

Instructions for Putting into Use

Read the ENTIRE IMPORTANT SAFETY INFORMATION section

at the beginning of this manual including all text under

subheadings therein before set up or use of this product.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:

Turn the Power Switch of the tool off and unplug the tool from its electrical

outlet before assembling or making any adjustments to the tool.

Note: For additional information regarding the parts listed in the following

pages, refer to Parts List and Assembly Diagram on page 14.

Trigger Lock

Trigger

(17)

Speed Switch

Orbital Mode

Level (16)

Blade Release

Lever

Blade Cover

(14)

Hex Key

Dust Chute

Connector

Base Plate (19)

Blade

(sold separately)

Roller Guide

Page 8 For technical questions, please call 1-888-866-5797. Item 62422

Blade Installation

1. Refer to the Chart below to select the proper

Saw Blade for the material being cut.

BLADE SELECTION AND SUITABLE SPEED

Material TPI Speed

Soft Wood 6 6

Hardwood 6 5

Plastic 12 4 ~ 6

Aluminum 12 3 ~ 6

Steel 24 2 ~ 4

Tile 24 1 ~ 3

Glass 32 1 ~ 3

Leather (Knife Edge) 4 ~ 6

Rubber (Knife Edge) 4 ~ 6

WARNING! Wear ANSI-approved safety goggles

and heavy-duty work gloves when changing blade.

2. Once the proper blade (sold separately)

is selected, lift the Blade Cover (14)

up to access the Blade Release

Lever. See Figure 1, below.

Blade Cover (14)

Blade Release

Lever

Collet

Blade

Roller

Guide

Figure 1

3. Pull Blade Release Lever counterclockwise

to open Blade Collet.

4. With the blade teeth facing FORWARD,

inset blade into blade holding Collet as far

as it will go. WARNING! Make sure blade’s

back edge is set against the roller guide.

5. Release the blade release lever. Pull on blade

until blade Collet snaps blade into place.

Page 9For technical questions, please call 1-888-866-5797.Item 62422

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section

at the beginning of this manual including all text under

subheadings therein before set up or use of this product.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:

Turn the Power Switch of the tool off and unplug the tool from its

electrical outlet before adjusting tool or installing accessories.

Work Piece and Work

Area Set Up

1. Designate a work area that is clean

and well-lit. The work area must not

allow access by children or pets to

prevent distraction and injury.

2. Route the power cord along a safe route

to reach the work area without creating a

tripping hazard or exposing the power cord

to possible damage. The power cord must

reach the work area with enough extra length

to allow free movement while working.

3. Secure loose work pieces using

a vise or clamps (not included) to

prevent movement while working.

4. There must not be objects, such as

utility lines, nearby that will present

a hazard while working.

Selecting Cutting Mode

1. The Jigsaw comes with four cutting modes

(three cutting settings and 1 straight cutting

mode). To change cutting mode, adjust the

Orbital Mode Lever (16). See Figure 2, below.

Figure 2

Orbital Mode Lever (16)

2. The settings are:

a. I = Straight line cutting (for

plastics and mild steel)

b. II = Small orbit (for aluminum

and hard wood)

c. III = Medium orbit (for wood, plywood

and fast cutting of aluminum)

d. IV = Large orbit (for fast cutting

wood and plywood)

Adjusting Jigsaw Speed

1. The Jigsaw’s speed can be adjusted between

500 and 3,000 strokes per minutes.

2. To adjust speed, turn the Speed Switch from

1 (the slowest speed) to 6 (the fastest speed).

See Figure 3, below.

Figure 3

Speed Switch

3. Use higher speeds to cut work pieces faster.

NOTICE: Refer to the Blade Selection

chart on page 7 to verify you are using the

correct speed with the appropriate blade.

Otherwise blade damage can occur.

Page 10 For technical questions, please call 1-888-866-5797. Item 62422

General Operating Instructions

1. Plug the Power Cord into the nearest

120 volt, grounded, electrical outlet.

2. Position the saw blade of the Jigsaw about

1/2” from the beginning cut line on the

work piece. Do not allow the saw blade

to come in contact with the work piece.

3. Squeeze the Trigger (17) to turn on the

Jigsaw. If operating the Jigsaw for an

extended period of time, press the Trigger

Lock to lock the Trigger in its “ON” position.

See Figure 4, below.

Figure 4

Trigger

(17)

Trigger

Lock

4. Allow the Saw Blade to stroke at full speed

before slowly feeding it into the work piece.

5. Make sure to hold the Jigsaw firmly

with both hands to avoid kickback.

Then, finish making the cut.

Dust Chute

1. The Jigsaw is supplied with a Dust Chute

adapter for a vacuum. It is attached

to the Dust Chute Connector located

at the back end of the housing.

2. To fasten the Dust Chute (sold separately)

in place, align the pins on Dust Chute with

slots in Connector. Push Dust Chute in and

turn clockwise to lock. See Figure 5, below.

Dust

Chute

Connector

Figure 5

Page 11For technical questions, please call 1-888-866-5797.Item 62422

Bevel and Metal Cutting

1. Use the included Hex Key to loosen the

Cap Screw (21) on the bottom of the

Base Plate (19). Tilt the base, allowing

for bevel cuts between 0 and 45°.

2. Retighten the Cap Screw once the

desired angle is reached.

3. For metal cutting, be sure to use a coolant

such as cutting oil during use. Failure to

add coolant will lead to greater blade wear.

If desired, grease the underside of the

work piece in place of adding coolant.

4. When finished with the Jigsaw, unlock and

release the Trigger to stop the Jigsaw. Wait

until the Saw Blade stops completely. Then,

remove the Jigsaw from the work piece.

5. To prevent accidents disconnect the

power cord after use. Clean, then store

the tool indoors out of children’s reach.

Page 12 For technical questions, please call 1-888-866-5797. Item 62422

Maintenance and Servicing

Procedures not specifically explained

in this manual must be performed

only by a qualified technician.

TO PREVENT SERIOUS INJURY

FROM ACCIDENTAL OPERATION:

Unlock and release Trigger and

unplug tool from its electrical outlet

before performing any inspection,

maintenance, or cleaning procedures.

TO PREVENT SERIOUS INJURY

FROM TOOL FAILURE: Do not use

damaged equipment. If abnormal noise

or vibration occurs, have the problem

corrected before further use.

Cleaning, Maintenance,

and Lubrication

1. BEFORE EACH USE, inspect the general

condition of the tool. Check for loose

hardware, misalignment or binding of

moving parts, cracked or broken parts,

damaged electrical wiring, and any other

condition that may affect its safe operation.

2. Inspect the Saw Blade. Replace with

a new Saw Blade when needed.

3. AFTER USE, wipe external surfaces

of the tool with clean cloth.

4. WARNING! If the supply cord of this

power tool is damaged, it must be replaced

only by a qualified service technician.

Page 13For technical questions, please call 1-888-866-5797.Item 62422

Troubleshooting

Problem Possible Causes Likely Solutions

Tool will not start. 1. Cord not connected.

2. No power at outlet.

3. Internal damage or wear.

(Carbon brushes or

switch, for example.)

1. Check that cord is plugged in.

2. Check power at outlet. If outlet is unpowered,

turn off tool and check circuit breaker.

If breaker is tripped, make sure circuit is right

capacity for tool and circuit has no other loads.

3. Have technician service tool.

Tool operates

slowly.

Extension cord too long

or wire size too small.

Eliminate use of extension cord.

If an extension cord is needed, use shorter/

heavier gauge cord. See Extension Cords

in Grounding section on page 5.

Performance

decreases

over time.

1. Accessory dull

or damaged.

2. Carbon brushes

worn or damaged.

1. Keep cutting accessories sharp.

Replace as needed.

2. Have qualied technician replace brushes.

Excessive noise

or rattling.

Internal damage or wear.

(Carbon brushes or

bearings, for example.)

Have technician service tool.

Overheating. 1. Forcing tool to

work too fast.

2. Accessory misaligned.

3. Accessory dull

or damaged.

4. Blocked motor

housing vents.

5. Motor being strained by

long or small diameter

extension cord.

1. Allow tool to work at its own rate.

2. Check and correct accessory to

fence and/or table alignment.

3. Keep cutting accessories sharp.

Replace as needed.

4. Wear ANSI-approved safety goggles and

NIOSH-approved dust mask/respirator while

blowing dust out of motor using compressed air.

5. Eliminate use of extension cord. If an extension

cord is needed, use one with the proper

diameter for its length and load. See Extension

Cords in Grounding section on page 5.

Follow all safety precautions whenever diagnosing or servicing the tool.

Disconnect power supply before service.

Page 14 For technical questions, please call 1-888-866-5797. Item 62422

Part Description Qty

1 Cutting Mode Selector 1

2 Wring Spring 1

3 Steel Ball 1

4 Washer Board 1

5 Ring Dowel 1

6 Left Cover 1

7 Left Half Housing 1

8 Cord Guard 1

9 Power Cord 1

10 Cord Clip 1

11 Screw St4×16 2

12 Axle 1

13 Positioning Pin 1

14 Blade Cover 1

15 Guard Rod 1

16 Orbital Mode Level 1

17 Trigger 1

18 Square Nut M4 1

19 Base Plate 1

20 Washer Board 1

21 Cap Screw 1

22 Base Plate Sheath 1

23 Stator 1

24 Bearing 607Z 1

Part Description Qty

25 Rotor 1

26 Carbon Brush 2

27 Copper Brush 2

28 Brush Holder 2

29 Bearing 608Z 1

30 Center Support 1

31 Axle Bearing K060913.5 1

32 Balance Plate 1

33 Axle 1

34 Slip Gutter 2

35 Balance Block 1

36 Gear 1

37 Washer Board 1

38 Washer Board 1

39 Guide Roller 1

40 Slide Rod Combination 1

41 Spring 1

42 Slide Mass 1

43 Speed Control Dial 1

44 Right Half Housing 1

45 Screw St4×20 8

46 Screw St4×38 1

47 Right Cover 1

48 Right Name Plate 1

Parts List and Assembly Diagram

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS

QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Parts List

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

Page 15For technical questions, please call 1-888-866-5797.Item 62422

Assembly Diagram

6 7 8 9

3536

3738

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality

and durability standards, and warrants to the original purchaser that this product is free from

defects in materials and workmanship for the period of 90 days from the date of purchase. This

warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or

accidents, repairs or alterations outside our facilities, criminal activity, improper installation,

normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,

injuries to persons or property, or for incidental, contingent, special or consequential damages

arising from the use of our product. Some states do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation of exclusion may not apply to

you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with

transportation charges prepaid. Proof of purchase date and an explanation of the complaint

must accompany the merchandise. If our inspection verifies the defect, we will either repair or

replace the product at our election or we may elect to refund the purchase price if we cannot

readily and quickly provide you with a replacement. We will return repaired products at our

expense, but if we determine there is no defect, or that the defect resulted from causes not

within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also

have other rights which vary from state to state.

Chicago Electric 5 Amp Heavy Duty Tool_Free Variable Speed Orbital Jig Saw Owner's manual

Brand: Chicago Electric

Model: 5 Amp Heavy Duty Tool_Free Variable Speed Orbital Jig Saw

Category: Power tools

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Chicago Electric 5 Amp Heavy Duty Tool_Free Variable Speed Orbital Jig Saw Owner's manual

This manual is also suitable for

Chicago Electric 5 Amp Heavy Duty Tool_Free Variable Speed Orbital Jig Saw Owner's manual

Related papers

Other documents