Sony HT-DDW2500 Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the Sony HT-DDW2500 Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Sony Corporation © 2009 Printed in Malaysia
4-127-415-11(1)
1: Installing the speakers
HT-DDW2500
Quick Setup Guide
2: Connecting the speakers
(1)
10 mm
A
Speaker cord (supplied)
A
DVD/BD
IN
DIGITAL
OPTICAL
SAT
IN
COAXIAL
ANTENNA
AM
SA-CD
/
CD
L
R
TV SAT
SPEAKERS
LR
SUBWOOFER
IN IN IN
FRONT
AKERS
LR
FRONT
SS-MSP2500
-
SS-MSP2500
3
DVD/BD
IN
DIGITAL
OPTICAL
SAT
IN
COAXIAL
ANTENNA
AM
SA-CD
/
CD
L
R
TV SAT
SPEAKERS
LR
SUBWOOFER
IN IN IN
FRONT
SPEA
SUBWOOFER
SS-WP3000
SS-WP3000
This Quick Setup Guide describes how to connect a DVD player or Blu-ray disc
player, satellite tuner or set-top box, TV, speakers and subwoofers so that you can
enjoy surround sound. Refer to the operating instructions supplied with the receiver
for details.
The illustrations in the guide designate speakers as
through
.
Front speaker (left)
Front speaker (right)
Subwoofer
Subwoofer
1: Installing the speakers
The illustration at left shows an example of two speakers and two subwoofers
confi guration. Refer to the operating instructions supplied with the receiver.
About speaker placement
The front speakers, subwoofers are magnetically shielded to allow it to be installed
near a TV set.
2: Connecting the speakers
The illustrations below show how to connect the speakers. Before you connect the
speakers, check the speaker label on the rear panel of the speakers for the speaker type.
For details, refer to step 2 of “Getting started” of the operating instructions supplied with
this receiver.
About speaker cords
Black striped wire is minus (–) in polarity and should be connected to the minus (–)
speaker terminal.
About speaker jacks
• Connect the
jack to the
jack of the receiver and connect the
jack to the
jack
of the receiver.
Refer to the illustration below for details of connecting speaker cords.
A
GB+DDW2500_2UC.indd 1GB+DDW2500_2UC.indd 1 1/6/2009 1:38:26 PM1/6/2009 1:38:26 PM
DVD/BD
IN
DIGITAL
OPTICAL
SAT
IN
COAXIAL
ANTENNA
AM
SA-CD
/
CD
L
R
TV SAT
IN IN IN
DVD/BD
IN
DIGITAL
OPTICAL
SAT
IN
COAXIAL
ANTENNA
AM
SA-CD
/
CD
L
R
TV SAT
SPEAKERS
LR
SUBWOOFER
IN IN IN
FRONT
C
D
E
L
R
VIDEO
B
E
Video components
3: Connecting other components
TV
B
Optical digital cord (not supplied)
C
Coaxial digital cord (supplied)
D
Audio cord (not supplied)
E
Video cord (not supplied)
Satellite tuner or Set-top box
5: Setting up other components
You should set up each component so that the sound is output from the speakers
correctly when you playback a connected component. Refer to the operating
instructions supplied with each component.
Note
If no digital signal is input through the COAXIAL or OPTICAL jack on the
receiver, “NO INPUT” appears on the display. This is not a malfunction.
After the setting
The receiver is now ready to use. Press the input button on the remote to select the
component you want to play back. Refer to the operating instructions supplied with
the receiver for details.
6: Setting up the system
You can make various settings to suit your preference. For details, refer to
“6: Adjusting the speaker levels and balance” in the operating instructions supplied
with the receiver.
Notes
Be sure to connect the video output
of the DVD player/Blu-ray disc player
and Satellite tuner/Set-top box to the
TV, so that the image is displayed
on the TV. Refer to the operating
instructions of each connected
component for details.
To fully enjoy surround sound while
watching TV programmes, connect
the audio output of your TV jacks as
shown and turn off the TV’s volume
or activate the TV’s muting function.
To enjoy surround sound from the
DVD player or Blu-ray disc player,
be sure to connect the coaxial digital
cord.
DVD player or Blu-ray disc player
3: Connecting other components
This is an example of how to connect this receiver and your components. Refer to
step 3 of “Getting started” of the operating instructions supplied with this receiver
for details on other connections and other components.
4: Connect all power cords last
Connect the AC power cord to a wall outlet.
Refer to “Connecting the AC power cord” in the operating instructions supplied
with the receiver.
GB+DDW2500_2UC.indd 2GB+DDW2500_2UC.indd 2 1/6/2009 1:38:29 PM1/6/2009 1:38:29 PM
/