ADC ADCP-75-237 Quick start guide
- Category
- Bridges & repeaters
- Type
- Quick start guide
9/2007
© 2007, ADC Telecommunications, Inc.
ADCP-75-239
1416981 Rev B
ADC In-Building
Wireless Repeater
Quick Start Guide
This Quick Start Guide covers the steps required for physical installation of an ADC In-Building
Wireless Repeater, and the initial power up instructions of the repeater. For additional information
and advanced installation instructions, refer to the ADC In-Building Wireless Repeater User Manual
(catalog number ADCP-75-237). A copy of the manual is on the enclosed CD.
Repeater must be configured before it is functional. See repeater User Manual (catalog number
ADCP-75-237) for configuration instructions.
INSTALLER OR CUSTOMER SUPPLIED ITEMS
◗ Hardware to secure wall mount bracket to wall.
◗ Dedicated AC power source for each unit.
◗ Coax cable and donor antenna with mount.
◗ Coax cable and service antenna with mount.
◗ Appropriate tools (hand and power) to mount repeater and antenna.
◗ Computer to load the GUI software and configure the repeater.
KIT CONTENTS SUPPLIED BY ADC
◗ USB (A to A) cable
◗ Power supply
◗ Power cable
◗ Repeater mounting bracket
◗ Repeater
◗ CD with documentation and GUI software
CHOOSE SUITABLE REPEATER AND ANTENNA LOCATIONS
◗ The best repeater location is a place as close as possible to the donor antenna. Maximum
coax cable length is based on link budget.
◗ Choose a repeater location that is central to your users preferably in an equipment closet or
other out of the way location.
◗ Choose a repeater location within 8 to 10 feet (2.5 to 3 meters) of an AC outlet.
◗ Service and donor antennas should be located at different heights to avoid interference.
1
2
Page 2
© 2007, ADC Telecommunications, Inc.
MOUNT REPEATER TO A WALL
U / L S / D
D / L S / D
ISO CHK
SLEEP
POWER
WALL OR
MOUNTING
BOARD
MOUNTING
BRACKET
MOUNTING
SCREWS
(4 PLACES)
REPEATER
22108-A
Refer to Figure 1.
◗ Using the mounting bracket as a template, mark mounting screw locations using the 1/4-inch
round holes.
◗ Secure mounting bracket to the wall with four #10 pan head screws or masonry anchors.
Figure 1. Repeater Installation
◗ Slide the repeater with bracket into slot in the mounting bracket.
3
Page 3
© 2007, ADC Telecommunications, Inc.
CONNECT THE CABLES
POWER
SOCKET
LOCATION
SERVICE
ANTENNA
CONNECTOR
USB
PORT
LOCATION
DONOR
ANTENNA
CONNECTOR
◗ There are four connection points on the repeater; two antenna connectors (donor and
service), one power connector, and one USB port. Connect cables at the locations shown in
Figure 2.
Figure 2. Connect Cables
4
Page 4
© 2007, ADC Telecommunications, Inc.
INSTALL SOFTWARE
CD contains software that must be installed on the PC. Files named for the different repeaters
are in folders. Open the appropriate folder for the repeater you have.
Install repeater USB drivers (Windows 2000 or XP). Driver file is on the CD.
Double click “setup.exe” file to start installation.
When PCS_Repeater Setup screen appears, click “OK”
Program automatically creates a default directory to install the program in. If you wish to
change installation directory, select “Change Directory” button to manually create a directory.
Click icon on screen to begin installation.
Choose a Program Group where program is to be installed.
When message “Successful installation completed” appears, click “OK” button.
The window will automatically close. You do not need to re-start the computer to begin
using the program.
For additional installation information refer to the User Manual (ADCP-75-237).
5
Page 5
© 2007, ADC Telecommunications, Inc.
CONFIGURE REPEATER COMMUNICATION PARAMETERS
Communication parameters must be set before the computer can communicate with the
repeater. All GUI controls can be used after connecting the repeater system using the following
“Connection” procedure.
Plug the USB cable in to the PC USB port and into the USB port on the repeater.
Open “Setting” -> “Connection”
Port Properties window opens.
◗ - Port: Select serial port number from 1 to 16
◗ - BaudRate: Select Baud rate “9600”bps
◗ - Data Type: DataBit: Select “8”bit, Parity: Select “None”, StopBit: Select “1”
◗ - Echo: Select “Off”, “LF”
◗ - Flow: Select “None”
◗ - H/W: Select both.
All options may use default settings except for “Port”. You must select correct port #. The correct
port is the serial port connecting computer to the equipment.
After finishing the selection, press “OK” to save and return to the main setting window. If you
press “Cancel”, the selections are not saved and you return to the Port Properties window. If the
selected port is incorrect, the program displays “It's not available” on the screen and requests
that you select another port.
You are now ready to configure the repeater to your system requirements. Refer to repeater
User Manual (catalog number ADCP-75-237) for band selection, RF parameters, and alarm
functionality.
6
Page 6
© 2007, ADC Telecommunications, Inc.
CUSTOMER INFORMATION AND ASSISTANCE
13944-N
PHONE:
WRITE:
PRODUCT INFORMATION AND TECHNICAL ASSISTANCE:
Contents herein are current as of the date of publication. ADC reserves the right to change the contents without prior notice.
In no event shall ADC be liable for any damages resulting from loss of data, loss of use, or loss of profits and ADC further
disclaims any and all liability for indirect, incidental, special, consequential or other similar damages. This disclaimer of
liability applies to all products, publications and services during and after the warranty period. This publication may be
verified at any time by contacting ADC’s Technical Assistance Center.
ADC Telecommunications (S’PORE) PTE, LTD;
100 Beach Road, #18-01, Shaw Towers.
Singapore 189702.
ADC Telecommunications, INC
PO Box 1101,
Minneapolis, MN 55440-1101, USA
ADC European Customer Service, INC
Belgicastraat 2,
1930 Zaventem, Belguim
connectivity[email protected]
U.S.A. or CANADA
Sales: 1-800-366-3691
Extension 73000
Technical Assistance: 1-800-366-3891
Connectivity Extension: 73475
Wireless Extension: 73476
EUROPE
Sales Administration: +32-2-712-65 00
Technical Assistance: +32-2-712-65 42
EUROPEAN TOLL FREE NUMBERS
Germany: 0180 2232923
UK: 0800 960236
Spain: 900 983291
France: 0800 914032
Italy: 0800 782374
ASIA/PACIFIC
Sales Administration: +65-6294-9948
Technical Assistance: +65-6393-0739
ELSEWHERE
Sales Admin
istration: +1-952-938-8080
Technical Assistance: +1-952-917-3475
7
-
1
-
2
-
3
-
4
-
5
-
6
ADC ADCP-75-237 Quick start guide
- Category
- Bridges & repeaters
- Type
- Quick start guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ADC SONEPLEX H2RX Installation Instructions Manual
-
-
-
-
-
ADC Telecommunications F8I-DVICSRIU1900 User manual
-
-
-
-
