Poulan Pro 952711951 User manual

Brand: Poulan Pro

Model: 952711951

Category: Power tools

Type: User manual

This manual is also suitable for

ENGLISH ESPAÑOL

FRANÇAIS

WARNING:

Read and follow all Safety Rules and Operating Instructions before

using this product. Failure to do so can result in serious injury .

ADVERTENCIA:

Lea el manual de instrucciones y siga todas las advertencias e

instrucciones de seguridad. El no hacerlo puede resultar en le-

siones graves.

AVERTISSEMENT:

Lire le manuel d’instructions et bien respecter tous les avertisse-

ments et toutes les instructions de sécurité. Tout défaut de le

faire pourrait entraîner des blessures graves.

PP333

For Occa sional Use Only

115249326 Rev. 2 3/1/10 BRW

Poulan PRO

7349 Statesville Road

Charlotte, NC 28269

Poulan PRO

850 Matheson Blvd. W est

Mississauga, Ontario L5V 0B4

Please do not return product to retailer.

Por favor, no devuelva el producto al lugar de compra.

Veuillez ne pas retourner le produit au détaillant.

1--800--554--6723

www.poulanpro.com

Registre su producto en línea en:

Enregistrez votre produit en ligne à l’adresse :

Instruction Manual

Manual de Instrucciones

Manuel d’Instructions

TABLE OF CONTENTS

Identification of Safety Symbols 2

Safety Rules 4

Assembly 6

Operation 10

Maintenance 17

Service & Adjustments 18

Storage 19

Troubleshooting Table 20

Limited Warranty Statement 21

Emissions Statement 21

IDENTIFICATION OF SAFETY SYMBOLS

W ARNING: Always use a metal shield and dust cup in the order

shown when using blades. Always use a handlebar and shoulder strap.

Ensure handlebar remains installed at all times.

WARNING: This unit can be dangerous! Careless or improper

use can cause serious injury .

WARNING: The blade continues to spin after

the trigger is released or engine is turned off. The

coasting blade can throw objects or seriously cut if

accidentally touched. Stop the blade by contacting the

right hand side of the coasting blade with material

already cut.

DANGER: Blade can thrust violently

away from material it does not cut. Blade

thrust can cause amputation of arms or legs.

Keep people and animals 50 feet (15 meters)

away.

Blade/trimmer line can throw objects vio-

lently. You can be blinded or injured. Al-

ways wear hearing protection and safety

glasses marked Z87. Always wear head

protection, heavy, long pants, long

sleeves, boots and gloves.

Secure hair above shoulder length. Do

not wear jewelry, loose clothing, or

clothing with loosely hanging straps,

ties, tassels, etc. They can be caught in

moving parts.

WARNING: Read the operator’ s manual before use. Failure to

follow instructions could result in serious injury to the operator and/or

bystanders. Save operator’ s manual.

IDENTIFICATION OF SAFETY SYMBOLS

Assist handle to be positioned only below the arrow.

When servicing unit, use only identical replacement

parts.

Never allow children to operate this unit.

Always stop unit and disconnect spark plug before clean-

ing or servicing.

Store unit indoors in a high, dry place out of the reach of

children. Store unit and fu el in area where fue l vapo rs can-

not reach sparks or open flames from water heaters, electric

mo t o r s or swit ch e s, furn aces, etc.

Use unleaded gasoline and two--stroke oil mixed at a ratio of 40:1

(2.5%).

W ARNING: Fire hazard. Never mix, pour, or store gasoline or

use the unit near a flame or sparks (including smoking, open flames, or

work that can cause sparks).

Hazard zone for thrown objects.

S Blade/trimmer line throws objects violently .

S You and others can be blinded/injured.

S Keep children, bystanders, and animals 50 feet

(15 meters) away.

OPTIONAL ATT ACHMENTS

Cutting attachment / guard,

Powerhead model Attachments T ype part. no.

Trimmer head WE fixed line 545053902 / 530071919

Grass blade/grass cutter 4-point blade, 530055892 / 530071383

8″ (20 cm)

diameter

Brushcutter attachment PP4000C 952711610

Attachments Type Part. no.

Edger attachment PP1000E 952711607

Cultivator attachment PP2000T 952711608

Blower attachment PP3000B 952711609

Pruner attachment PP5000P 952711612

Pruner attachment PP5500P 952711672

These attachments used in combination with the specified powerhead have been evaluated

to applicable ISO-- and EN safety requirement standards by the Swedish Machinery Testing

Institute.

These attachments used in combination with the specified powerhead have been evaluated

to ANSI B175.3--2003, “Grass Trimmers and Brushcutters -- Safety Requirements”. These

combinations have been evaluated by Underwriter’s Laboratories Inc. (UL) and are conse-

quently UL listed:

PP333

SAFETY RULES

WARNING: When using gardening

appliances, basic safety precautions must al-

ways be followed to reduce the risk of fire and

serious injury.

DANGER: This power tool can be dan-

gerous! This unit can cause serious injury in-

cluding amputation or blindness to the operator

and others. The warnings and safety instruc-

tions in this manual must be followed to provide

reasonable safety and efficiency in using the

unit. The operator is responsible for following the

warnings and instructions in this manual and on

the unit. Read the entire instruction manual be-

fore assembling and using the unit! Restrict the

use of this unit to persons who read, under-

stand, and follow the warnings and instructions

in this manual and on the unit. Never allow chil-

dren to operate this unit.

SAFETY INFORMATION

ON THE UNIT

INSTRUCTION

MANUAL

WARNING: Do not use trimmer head

as a fastening device for the blade.

If situations occur which are not covered in this

manual, use care and good judgment. If you

need assistance, contact contact an authorized

service dealer or call 1--800--554--6723.

OPERATOR SAFETY

S Dress properly. Always wear safety

glasses or similar eye protection when op-

erating, or performing maintenance on your

unit (safety glasses are available). Eye

protection should be marked Z87.

S Always wear face or dust mask if operation

is dusty .

S Always wear heavy, long pants, long sleeves,

boots, and gloves. Wearing safety leg guards

is recommended.

S Always wear foot protection. Do not go

barefoot or wear sandals.

S Secure hair above shoulder length. Secure

or remove loose clothing and jewelry or cloth-

ing with loosely hanging ties, straps, tassels,

etc. They can be caught in moving parts.

S Being fully covered also helps protect you

from debris and pieces of toxic plants

thrown by spinning line/blade.

S Stay Alert. Do not operate unit when you are

tired, ill, upset or under influence of alcohol,

drugs, or medication. Watch what you are

doing; use comm on sense.

S W ear hearing protection.

S Never start or run the engine inside a

closed room or building. Breathing exhaust

fumes can kill.

S Keep handles free of oil and fuel.

S Always use the handlebar and a properly

adjusted shoulder strap with a blade (see

ASSEMBLY).

UNIT/MAINTENANCE SAFETY

WARNING: Stop unit and disconnect

the spark plug before performing mainte-

nance (except carburetor adjustments).

S Look for and replace damaged or loose

parts before each use. Look for and repair

fuel leaks before use. Keep unit in good

working condition.

S Throw away blades that are bent, warped,

cracked, broken, or damaged in any other

way. Replace trimmer head parts that are

cracked, chipped, broken, or damaged in

any other way before using the unit.

S Maintain unit according to recommended

procedures. Keep blade sharp. Keep cut-

ting line at the proper length.

S Use o nly Pou lan PRO brand replacement

line. Never use wire, rope, string, etc.

S Install required shield properly before using

the unit. Use the metal shield for all metal

blade use. Use the plastic shield for all line

trimmer use.

S Use only specified blade or trimmer head;

make sure it is properly installed and se-

curely fastened.

S Never start engine with clutch shroud re-

moved. The clutch can fly off and cause se-

rious injury.

S Be sure blade or trimmer head stops turning

when engine idles.

S Make carburetor adjustments with the lower

end supported to prevent blade or trimmer line

from contacting any object. Hold unit by hand;

do not use the shoulder strap for support.

S Keep others away when making carburetor

adjustments.

S Use only recommended Po ula n P RO ac-

cessories and replacement parts.

S Have all maintenance and service not ex-

plained in this manual performed by your au-

thorized service dealer .

FUEL SAF ETY

S Mix and pour fuel outdoors.

S Keep away from sparks or flames.

S Use a container approved for fuel.

S Do not smoke or allow smoking near fuel or

the unit or while using the unit.

S Avoid spilling fuel or oil. Wipe up all fuel

spills before starting engine.

S Move at least 10 feet (3 meters) away from

fueling site before starting engine.

S Stop engine and allow it to cool before re-

moving fuel cap.

S Empty the fuel tank before storing or trans-

porting the unit. Use up fuel left in the car-

buretor by starting the engine and letting it

run until it stops.

S Store unit and fuel in area where fuel vapors

cannot reach sparks or open flames from

water heaters, electric motors or switches,

furnaces, etc.

S Always store gasoline in a container ap-

proved for flammable liquids.

CUTTING SAFETY

WARNING: Inspect the area to be

cut before each use. Remove objects (rocks,

broken glass, nails, wire, string, etc.) which

can be thrown or become entangled in the

blade or trimmer head.

S Keep others including children , anim als, by-

standers, and helpers at least 50 feet (15 me-

ters) away. Bystanders should be encour-

aged to wear safety glasses. Stop engine

immediately if you are approached.

S Always keep engine on the right--hand side

of your body.

S Hold the unit firmly with both hands.

S Keep firm footing and balance. Do not over-

reach.

S Keep blade or trimmer head below waist

level. Do not raise e ngine above your waist.

S Keep all parts of your body away from blade,

trimmer head, and muffler when engine is run-

ning. A hot muffler can cause serious burns.

S Cut from your left to your right. Cutting on

right side of the shield will throw debris

away from the operator.

S Use only in daylight or good artificial light.

S Use only for jobs explained in this manual.

TRANSPORTING AND STORAGE

S Stop the unit before carrying.

S Keep muffler away from your body.

S Allow the engine to cool and secure the unit

before storing or transporting it in a vehicle.

S Empty the fuel tank before storing or trans-

porting the unit. Use up fuel left in the carbu-

retor by starting the engine and letting it run

until it stops.

S Store unit so the blade or line limiter blade

cannot accidentally cause injury. The unit

can be hung by the shaft.

S Store unit out of reach of children.

WARNING: The engine exhaust

from this product contains chemicals known

to the State of California to cause cancer, birth

defects or other reproductive harm.

SAFETY NOTICE: Exposure to vibrations

through prolonged use of gasoline powered

hand tools could cause blood vessel or nerve

damage in the fingers, hands, and joints of

people prone to circulation disorders or ab-

normal swellings. Prolonged use in cold

weather has been linked to blood vessel dam-

age in otherwise healthy people. If symptoms

occur such as numbness, pain, loss of

strength, change in skin color or texture, or

loss of feeling in the fingers, hands, or joints,

discontinue the use of this tool and seek med-

ical attention. An anti--vibration system does

not guarantee the avoidance of these prob-

lems. Users who operate power tools on a

continual and regular basis must monitor-

closely their physical condition and the condi-

tion of this tool.

SPECIAL NOTICE: This unit is equipped

with a temperature limiting muffler and spark

arresting screen which meets the require-

ments of California Codes 4442 and 4443. All

U.S. forest land and the states of California,

Idaho, Maine, Minnesota, New Jersey, Ore-

gon, and Washington require by law that

many internal combustion engines be

equipped with a spark arresting screen. If you

operate in a locale where such regulations ex-

ist, you are legally responsible for maintaining

the operating condition of these parts. Failure

to do so is a violation of the law. For normal

homeowner use, the muffler and spark arrest-

ing screen will not require any service. After

50 hours of use, we recommend that your

muffler be serviced or replaced by your autho-

rized service dealer .

ASSEMBLY

CARTON CONTENTS

Check carton contents against the following list:

S Powerhead

S Attachment (with trimmer head installed)

S Cupped washer

S Large nut for installing blades

S Hex wrench

S Handlebar

S Bracket cover

S Bracket cover screws (2)

S Metal blade shield

S Blade shield screws (4)

S 4--point weed blade

S Plastic shield

S Wing nut (screwed onto plastic shield)

S Shoulder strap with warning

S Container of oil

WARNING: Always stop unit and dis-

connect spark plug before performing any as-

sembly procedures.

WARNING: If received assembled,

repeat all steps to ensure your unit is properly

assembled and all fasteners are secure.

Examine parts for damage. Do not use dam-

aged parts.

NOTE: If you need assistance or find parts

missing or damaged, call 1-800-554-6723.

It is normal for the fuel filter to rattle in the

empty fuel tank.

Finding fuel or oil residue on muffler is normal

due to carburetor adjustments and testing

done by the manufacturer.

TOOLS REQUIRED

S Hex wrench (provided)

S Adjustable wrench

S Phillips screwdriver

INSTALLING BRUSHCUTTER

ATTACHMENT

CAUTION:

When installing brushcutter at-

tachment, place the unit on a flat surface for

stability.

1. Loosen the coupler by turning the knob

counterclockwise.

Shipping

protector

Coupler

Knob

LOOSEN

TIGHTEN

2. Remove shipping protector from coupler.

3. Remove the shaft cap from the brushcutter

attachment (if present).

4. Position locking/release button of attach-

ment into guide recess of coupler.

5. Push the attachment into the coupler until

the locking/release button snaps into the

primary hole.

6. Before using the unit, tighten the knob se-

curely by turning clockwise.

Coupler

Primary Hole

Upper

Shaft

Locking/

Release

Button

Attachment

Guide Recess

WARNING: Make sure the locking/

release button is locked in the primary hole

and the knob is securely tightened before op-

erating the unit. All attachments are designed

to be used in the primary hole unless other-

wise stated in the applicable attachment in-

struction manual. Using the wrong hole could

lead to serious injury or damage to the unit.

Locking/Release

Button in Primary Hole

For assembly of optional attachments (see

list on page 11), refer to the ASSEMBLY sec-

tion of the applicable attachment instruction

manual.

ATTACHING T HE HAN DL EBA R

DANGER: To avoid serious injury, the

barrier portion of the handlebar must be installed

as shown to provide a barrier between operator

and the spinning blade.

1. Locate the decal on the handlebar. This

decal includes an arrow. Position the

handlebar with the mounting bracket at

the end of the arrow.

2. Position the bracket cover over the han-

dlebar. Again make sure the handlebar is

at the end of the arrow.

3. Insert screws and hand tighten only. Be

sure the handlebar is installed correctly;

then, tighten each screw securely with the

hex wrench.

Screw

Mounting

Bracket

Handlebar

Bracket Cover

Shoulder

Strap Clamp

ASSEMBLY OF SHOULDER STRAP

WARNING: Proper shoulder strap

and handlebar adjustments must be made

with the engine completely stopped before

using unit.

1. Insert your right arm and head through

the shoulder strap and allow it to rest on

your left shoulder. Make sure the danger

sign is on your back and the hook is to the

right side of your waist.

NOTE: A one-half twist is built in the shoul-

der strap to allow the strap to rest flat on the

shoulder.

2. Adjust the strap, allowing the hook to be

about 6 inches (15 cm) below the waist.

3. Fasten the strap hook to the clamp located

between the throttle trigger and the handle-

bar mounting bracket and lift the tool to the

operating position.

4. Try on shoulder strap and adjust for fit

and balance before starting the engine or

beginning a cutting operation.

NOTE: It may be necessary to relocate the

shoulder strap clamp on the shaft for proper

balancing of unit.

TO RELOCATE SHOULDER STRAP

CLAMP:

1. Loosen and remove both clamp screws.

2. Place the upper shoulder strap clamp

over the shaft.

3. Position the lower shoulder strap clamp

under the shaft and align the upper and

lower clamp screw holes.

Upper Shoulder

Strap Clamp

Screws

Lower Shoulder

Strap Clamp

4. Insert two screws into the screw holes.

5. Secure shoulder strap clamp by tighten-

ing screws with a hex wrench.

SHOULDER STRAP

ADJUSTMENT

FOR BALANCE

6 inches

(15 cm)

below

waist

30 inches

(76 cm)

minimum

4 -- 12 inches

(10 -- 30 cm)

above

ground

30 inches

(76 cm)

minimum

CONFIGURING YOUR UNIT

You can configure your unit using a cutting head

for grass and light weeds, or a weed blade for

cutting grass, weeds, and brush up to 1/2 inch

(1 cm) in diameter . To assemble your unit, go to

the section for the desired configuration and fol-

low the instructions.

ASSEMBLY INFORMATION --

TRIMMER HEAD

TRIMMER

HEAD

NOTE:Remove the blade and metal shield be-

fore attaching the plastic shield and trimmer

head. To rem ove blade, align hole in the dust

cup with the hole in the side of the gearbox by

rotating the blade. Insert a small screwdriver

into aligned holes. This wil l keep the shaft f ro m

turning while loosening the blade nut. Remove

blade nut by turning clockwise. Remove the

screwdriver . Remove both washers and blade.

To remove metal shield, loosen and remove the

four mounting screws. See A TT ACHING THE

MET AL SHIELD and INST ALLA TION OF THE

MET AL BLADE for illustrations. Be sure to store

all parts and instructions for future use.

ATTACHING THE PLASTIC S HIELD

ANDTRIMMERHEAD

WARNING: The shield must be prop-

erly installed. The shield provides partial

protection to the operator and others from the

risk of thrown objects, and is equipped with a

line limiter blade which cuts excess line to the

proper length. The line limiter blade (on un-

derside of shield) is sharp and can cut you.

1. Remove wing nut from shield.

2. Insert bracket into slot on shield.

3. Pivot shield until bolt passes through hole

in bracket.

Bracket

Slot

Shield

4. Reinstall wing nut and tighten securely.

WingNut

NOTE: If your unit has a plastic cover over

the threads on the threaded shaft, remove the

covering to expose the threads. Before instal-

ling the trimmer head, make sure the dust cup

and retaining washer are positioned on the

gearbox as shown below.

Retaining

Washer

Dust Cup

Gearbox

Aligned Holes

NOTE: Make sure all parts are properly

installed as shown in the illustration before

installing the trimmer head.

5. Align hole in the dust cup with the hole in the

side of the gearbox by rotating the dust cup.

6. Insert a small screwdriver into aligned

holes. This will keep the shaft from turn-

ing while tightening trimmer head.

7. While holding the screwdriver in position,

thread trimmer head onto the shaft in the

direction shown on the decal (counter-

clockwise looking from bottom of unit).

Tighten until secure.

NOTE: The retaining washer must be posi-

tioned with the raised section facing toward the

gearbox.

ASSEMBLY INFORMATION -- WEED

BLADE

WEED

BLADE

NOTE: Remove the trimmer head and plastic

shield before attaching the metal shield and

installing the weed blade. To remove the trim-

mer head, align hole in the dust cup with the hole

in the side of the gearbox by rotating the dust

cup. Insert a small screwdriver into aligned

holes. This will keep the shaft from turning while

loosening the trimmer head. Remove the trim-

mer head by turning clockwise. Remove the

screwdriver. To remove the plastic shie ld, loos-

en and remove wing nut. Pivot shield to release

bracket from slot. See INST AL LATION OF THE

CUTTI NG HEAD an d ATTACHING THE

PLASTIC SHIELD for illustrations. Be sure to

store all parts and instructions for future use.

Never use the trimmer head with the metal

blade installed.

ATTACHING THE METAL SHIELD

WARNING: The metal shield must

be properly installed on the tool anytime the

tool is used with a blade. The forward tip of the

metal shield helps to reduce the occurrence

of blade thrust which can cause serious injury

such as amputation to the operator or by-

standers. Failure to install the shield in the

position shown can result in serious injury to

the operator. The length of the shield must be

aligned with the length of the shaft.

Shaft

Metal

Shield

Blade

1. Place the metal shield under the gearbox,

and align the screw holes.

Shield

Gearbox

2. Insert and thread the 4 mounting screws

through the holes of the gearbox and the

metal shield. Tighten evenly and secure-

ly with the hex wrench provided.

INSTALLATION OF THE METAL

BLADE

WARNING: Wear protective gloves

when handling or performing maintenance on

the blade to avoid injury. The blade is sharp and

can cut you even when it is not moving.

WARNING: Do not use any blades, or

fastening hardware other than the washers and

nuts shown in the following illustrations. These

parts must be provided by Poulan/WEED

EA TER and installed as shown below . Failure to

use proper parts can cause the blade to fly off

and seriously hurt you or others.

NOTE: The dust cup and retaining washer are

located on the gearbox shaft and not in the parts

bag. All other fasteners mentioned in the follow-

ing assembly steps are in the parts bag.

1. Remove the retaining washer from the

threaded shaft of the gearbox. Leave the

dust cup on the shaft.

2. Install the blade and the retaining washer

over the threaded shaft.

3. M ake sure the raised part of the retaining

washer is facing the gearbox and the

raised area fits into the hole in the center

of the blade.

4. Slide the blade and retaining washer onto

the shaft of the gearbox.

5. Place the cupped washer onto the shaft.

Make sure the cupped side of the washer

is toward the blade.

6. Install the blade nut by threading onto the

shaft counterclockwise (looking from bot-

tom of unit).

Shield

Blade

Retaining

Washer

Aligned Holes

Cupped

Washer

Nut

Threaded Shaft

Gearbox

Dust Cup

NOTE: Make sure all parts are in place as il-

lustrated, and the blade is sandwiched between

the dust cup and the retaining washer. There

should be no space between the blade and the

dust cup or the retaining washer .

7. Align hole in dust cup with hole in side of

gearbox by rotating the blade.

8. Insert a small screwdriver into aligned

holes. This will keep the shaft from turn-

ing while tightening the blade nut.

9. TIghten blade nut firmly with a wrench while

holding screwdriver in position.

10. Remove the screwdriver .

11. Turn blade by hand. If the blade binds

against the shield, or appears to be uneven,

the blade is not centered, and you must re-

install.

NOTE: To remove blade, insert

screwdriver into aligned holes. Unthread

the nut and remove parts. Be sure to store

parts and instructions for future use.

OPERATION

KNOW YOUR UNIT

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR UNIT.

Compare the illustrations with your unit to familiarize yourself with the location of the various controls

and adjustments. Save this manual for future reference.

Line Limiter

Blade

Handlebar

ON/STOP Switch

Shield

Trimmer Head

Shaft

Coupler

Blade

Muffler

Start Lever

Starter Handle

Primer Bulb

Throttle Trigger

ON/STOP SWITCH

The ON/STOP switch is located on the trigger

handle and is used to stop the engine. To stop

the engine, push and release the engine

ON/STOP switch.

PRIMER BULB

The PRIMER BULB removes air from the car-

buretor and fuel lines and fills them with fuel.

This allows you to start the engine with fewer

pulls on the starter rope. Activate the primer

bulb by pressing it and allowing it to return to

its original form.

START LEVER

The ST ART LEVER helps to supply fuel to the

engine to aid in starting. Activate the starting

system by moving the sta r t le ver to the S TART

position. DO NOT squeeze the throttle trigger

until the engine has started and runs. After the

engine starts, allow the engine to warm--up

10--15 seconds, then fully squeeze the throttle

trigger to deactivate the starting system.

COUPLER

The COUPLER enables optional attach-

ments to be installed on the unit.

BEFORE STARTING ENGINE

WARNING: Be sure to read the fuel

information in the safety rules before you be-

gin. If you do not understand the safety rules,

do not attempt to fuel your unit. Call

1-800-554-6723.

FUELING ENGINE

WARNING: Remove fuel cap slowly

when refueling.

HELPFUL TIP

To obtain the correct oil mix

ratio, pour 3.2 ounces of

2-- cycle synthetic oil into

one gallon of fresh gas.

This engine is certified to operate on unleaded

gasoline. Before operation, gasoline must be

mixed with a good quality synthetic 2-cycle air-

cooled engine oil designed to be mixed at a ratio

of 40:1. Poulan/WEED EA TER brand synthetic

oil is recommended. Mix gasoline and oil at a ra-

tio of 40:1. A 40:1 ratio is obtained by mixing 3.2

fluid ounces (95 ml) of oil with 1 gallon (4 liters)

of unleaded gasoline. DO NOT USE automotive

oil or marine oil. These oils will cause engine

damage. When mixing fuel, follow instructions

printed on container . Once oil is added to gaso-

line, shake container momentarily to assure that

the fuel is thoroughly mixed. Always read and

follow the safety rules relating to fuel before fuel-

ing your unit.

CAUTION: Never use straight gasoline in

your unit. This will cause permanent engine

damage and void the limited warranty.

FUEL REQUIREMENTS

This engine requires the use of minimum 87

octane [R+M]/2 clean gasoline.

IMPORTAN T

Use of alcohol blended fuels (called gasohol or

using ethanol or methanol) can cause major en-

gine performance and durability problems.

WARNING: Alternative fuels (not gas-

oline) such as E--15 (15% alcohol), E--20 (20%

alcohol), E--85 (85% alcohol) are NOT classified

as gasoline and are NOT approved for use in

2--stroke gasoline engines. Use of alternative

fuels will cause problems such as: improper

clutch engagements, overheating, vapor lock,

power loss, lubrication deficiency, deterioration

of fuel lines, gaskets and internal carburetor

components, etc. Alternative fuels cause high

moisture absorption into the fuel/oil mixture

lead ing to oil and fuel separation.

HOW TO STOP YOUR UNIT

S Release the throttle trigger.

S Push and release the engine ON/STOP

swit ch. T h e swit ch wi l l aut o mat i ca l l y ret u rn to

the ON position. W ait 5 seconds before at-

tempting to restart unit to allow switch to reset.

ON/STOP Switch

HOW TO START YOUR UNIT

WARNING: Avoid any contact with the

muffler . A hot muffler can cause serious burns.

Starting Position

HELPFUL TIP

If your engine still does not

start after following these

instructions, please call

1--800--554--6723.

STARTING A COLD ENGINE (or a

warm engine after running out of

fuel)

NOTE:

DO NOT squeeze the throttle trigger

until the engine has started and runs.

Muffler

Start

Lever

Starter Handle

Primer Bulb

Throttle

Trigger

1. Set unit on a flat surface.

2. Slowly press the primer bulb 6 times.

3. Move the start lever to the ST AR T position.

4. Pull starter rope handle sharply until en-

gine starts and runs.

5. Allow unit to run for 10--15 seconds, then

fully squeeze the throttle trigger to disen-

gage the starting system.

STARTING A WARM ENGINE

Pull starter rope sharply until engine starts

and runs.

NOTE: Normally, the warm starting procedure

can be used within 5 -- 10 minutes after the unit

is turned STOP. If the unit sits for more than 10

minutes without being run, it will be necessary to

start the unit by following the steps under

STARTINGACOLDENGINEorfollowingthe

starting instruction steps shown on the unit.

STARTING A FLOODED ENGINE

Move the start lever to the RUN position and

fully squeeze throttle trigger. Pull the starter

handle repeatedly while squeezing throttle

trigger until engine starts and runs. This could

require pulling the starter handle many times,

depending on how badly the unit is flooded.

If the unit still doesn’t start, refer to TROUBLE-

SHOOTING TABLE or call 1-800-554-6723.

OPERATING THE COUPLER

This model is equipped with a coupler which

enables optional attachments to be installed.

The optional attachments are:

MODEL:

Edger PP1000E.....................

Cultivator PP2000T..................

Blower PP3000B....................

Pruner PP5000P....................

Pruner PP5500P....................

WARNING: Always stop unit and dis-

connect spark plug before removing or instal-

ling attachments.

REMOVING TRIMMER ATTACH-

MENT (OR OTHER OPTIONAL

ATTACHMENTS)

CAUTION:

When removing or installing at-

tachments, place the unit on a flat surface for

stability .

1. Loo sen the coupler by turning the knob

counterclockwise.

Attachment

Coupler

Knob

LOOSEN

TIGHTEN

2. Press and hold the locking/release button.

Locking/Release

Button

Coupler

Upper Shaft

Attachment

3. While securely holding the engine and

upper shaft, pull the attachment straight

out of the coupler .

INSTALLING OPTIONAL ATTACH -

MENTS

1. Remove the shaft cap from the attach-

ment (if present).

2. Position locking/release button of attach-

ment into guide recess of coupler.

3. Push the attachment into the coupler until

the locking/release button snaps into the

primary hole.

4. Before using the unit, tighten the knob se-

curely by turning clockwise.

Coupler

Primary Hole

Upper

Shaft

Locking/

Release

Button

Attachment

Guide Recess

WARNING: Make sure the locking/

release button is locked in the primary hole

and the knob is securely tightened before op-

erating the unit. All atta c hments a re designed

to be used in the primary hole unless otherwise

stated in the applicable attachment instruction

manual. Using the wrong hole could lead to seri-

ous injury or damage to the unit.

Locking/Release

Button in Primary Hole

OPERATING INSTRUCTIONS

It is recommended that the engine not be

operated for longer than 1 minute at full

throttle.

OPERA TING POSITION

Boots

Heavy ,

Long Pants

Eye Protection

ALWAYS WEAR:

Cut from your left to your right.

Hearing

Protection

When operating unit, clip shoulder strap onto

clamp, stand as shown and check for the fol-

lowing:

S Wear hearing protection, eye protection,

head protection and heavy clothing.

S Extend your left arm and hold handlebar

grip with your left hand.

S Hold throttle grip with your right hand with

finger on throttle trigger.

S Keep unit below waist level.

S Keep shoulder strap pad centered on your

left shoulder and danger sign centered on

your back.

S Maintain full weight of tool on your left

shoulder.

S Without bending over, keep the blade or

trimmer head near and parallel to the

ground and not crowded into material being

cut.

OPERAT ING INSTRUCTIONS FOR

USE WITH TRIMMER HEAD

WARNING: Always wear eye protec-

tion. Never lean over the trimmer head. Rocks

or debris can ricochet or be thrown into eyes

and face and cause blindness or other serious

injury .

Before trimming, bring engineto a speed suffi-

cient to cut material to be trimmed.

Do not run the engine at a higher speed than

necessary. The cutting line will cut efficiently

when the engine is run at less than full throttle.

At lower speeds, there is less engine noise and

vibration.

Always release the throttle trigger and allow

the engine to return to idle speed when not

cutting.

To stop engine:

S Release the throttle trigger.

S Push and release the engine ON/STOP

switch.

CUTTING METHODS

WARNING: Use minimum speed

and do not crowd the line when cutting around

hard objects (rock, gravel, fence posts, etc.),

which can damage the trimmer head, become

entangled in the line, or be thrown causing a

serious hazard.

S The tip of the line does the cutting. You will

achieve the best performance and mini-

mum line wear by not crowding the line into

the cutting area. The right and wrong ways

are shown below.

Tip of the line

does the cutting.

Right Wrong

Line crowded into

work area.

S The line will easily remove grass and

weeds from around walls, fences, trees and

flower beds, but it also can cut the tender

bark of trees or shrubs and scar fences.

S For trimming or scalping, use less than full

throttle to increase line life and decrease

head wear, especially:

S During light duty cutting.

S Near objects around which the line can

wrap such as small posts, trees or fence

wire.

S For mowing or sweeping, use full throttle for

a good clean job.

TRIMMING -- Hold the bottom of the trimmer

head about 3 inches (8 cm) above the ground

and at an angle. Allow only the tip of the line to

make contact. Do not force trimmer line into

work area.

Trimming

3 inches (8 cm)

above ground

SCALPING -- The scalping technique removes

unwanted vegetation down to the ground. Hold

the bottom of the trimmer head about 3 inches

(8 cm) above the ground and at an angle. Allow

the tip of the line to strike the ground around

trees, posts, monuments, etc. This technique in-

creases line wear .

Scalping

MOWING -- Your trimmer is ideal for mowing

in places conventional lawn mowers cannot

reach. In the mowing position, keep the line

parallel to the ground. Avoid pressing the

head into the ground as this can scalp the

ground and damage the tool.

Mowing

SWEEPING -- The fanning action of the rotat-

ing line can be used to blow away loose debris

from an area. Keep the line parallel to and

above the area surface and swing the tool

from side to side.

Sweeping

OPERAT ING INSTRUCTIONS FOR

USE WITH WEED BLADE

S Bla d e Thru s t is a reaction that only occurs

when using a bladed unit. This reaction can

cause serious injury such as amputation.

Carefully study this section. It is important that

you understand what causes blade thrust,

how you can reduce the chance of its

occurring, and how you can remain in control

of unit if blade thrust occurs.

S WHAT CAUSES BLADE THRUST -- Blade

Thrust can occur when the spinning blade

contacts an object that it does not cut. This

contact causes the blade to stop for an instant

and then suddenly move or “thrust” away

from the object that was hit. The “thrusting”

reaction can be violent enough to cause the

operator to be propelled in any direction and

lose control of the unit. The uncontrolled unit

can cause serious injury if the blade contacts

the operator or others.

S WHEN BLADE THRUST OCCURS --

Blade Thrust can occur without warning if

the blade snags, stalls, or binds. This is

more likely to occur in areas where it is

difficult to see the material being cut. By

using the unit properly, the occurrence of

blade thrust will be reduced and the

operator will be less likely to lose control.

S Cut only grass, weeds, and woody brush up

to 1/2 inch (1 cm) in diameter with the weed

blade. Do not let the blade contact material

it cannot cut such as stumps, rocks,

fences, metal, etc., or clusters of hard,

woody brush having a diameter greater

than 1/2 inch (1 cm).

S Keep the blade sharp. A dull blade is more

likely to snag and thrust.

S Cut only at full throttle. The blade will

have maximum cutting power and is less

likely to bind or stall.

S “Feed” the blade deliberately and not too

rapidly. The blade can thrust away if it is fed

too rapidly.

S Cut only from your left to your right. Cutting on

right side of the shield will throw debris away

from the operator.

S Use the shoulder strap and keep a firm grip

on the unit with both hands. A properly

adjusted shoulder strap will support the

weight of the unit, freeing your arms and

hands to control and guide the cutting motion.

S Keep feet comfortably spread apart and

braced for a possible sudden, rapid thrust of

unit. Do not overreach. Keep firm footing and

balance.

S Keep blade below waist level; it will be

easier to maintain control of unit.

S Do not raise the engine above your waist as

the blade can come dangerously close to

your body.

S Do not swing unit with such force that you

are in danger of losing your balance.

Bring the engine to cutting speed before enter-

ing the material to be cut.If the blade does not

turn when you squeeze the throttle trigger, make

sure shaft is fully inserted into the engine.

Always release the throttle trigger and allow

engine to return to idle speed when not cut-

ting. The blade should not turn while the en-

gine is running at idle. If the blade turns at idle,

do not use your unit. Refer to the CARBURE-

TOR ADJUSTMENT section or contact your

authorized service dealer .

S Maintain good firm footing while using the

unit. Do this by planting feet firmly in a

comfortable apart position.

S Cut while swinging the upper part of your

body from left to right.

S Asyoumoveforwardtothenextareatocut,

be sure to maintain your balance and footing.

Cut using the 2

o’clock to 4 o’clock

position of the

blade

2 o’clock

4 o’clock

RECOMMENDED CUTTING POSITION

WARNING: The operator or others

must not try to clear away cut material with the

engine running or the blade turning to avoid

serious injury. Stop engine and blade before

removing materials wrapped around blade or

shaft.

ADDITIONAL SAFETY RULES

FOR OPTIONAL ATTACHMENTS

WARNING: For each optional at-

tachment used, read entire instruction manu-

al before use and follow all warnings and in-

structions in manual and on attachment.

WARNING: Ensure handlebar re-

mains installed on upper shaft (engine end of

unit) at all times.

Handlebar

EDGER SAFET Y

WARNING: Inspect the area to be

edged before each use. Remove objects

(rocks, broken glass, nails, wire, etc.) which

can be thrown by the blade or can wrap

around the shaft.

WARNING: Blade rotates momen-

tarily after the trigger is released or engine is

turned off. The blade can seriously cut you or

others. Allow blade to stop before removing it

from the cut.

S Throw away blades that are bent, warped,

cracked, broken or damaged in any other

way. Replace parts that are cracked,

chipped, or damaged before using the unit.

S Do not attempt to remove cut material nor

hold material to be cut when the engine is

running or when cutting blade is moving.

S Always keep the wheel and depth adjusting

skid in contact with the ground.

S Always push the unit slowly over the

ground. Stay alert for uneven sidewalks,

holes in the terrain, large roots, etc.

BLOWER/VACUUM SAF ET Y

WARNING: Inspect area before

starting unit. Remove all debris and hard ob-

jects such as rocks, glass, wire, etc. that can

ricochet, be thrown, or otherwise cause injury

or damage during operation.

S Do not set unit on any surface except a clean,

hard area while engine is running. Debris

such as gravel, sand, dust, grass, etc., could

be picked up by the air intake and thrown out

through discharge opening, damaging unit,

property , or causing serious injury to

bystanders or operator .

S Never place objects inside the blower tubes,

vacuum tubes or blower outlet. Always direct

the blowing debris away from people,

animals, glass, and solid objects such as

trees, automobiles, walls, etc. The force of air

can cau se ro cks, d i r t , or sticks to be th r o wn or

to ricochet which can hurt people or animals,

break glass, or cause other damage.

S Never run unit without the proper

equipment attached. When using your unit

as a blower , always install blower tubes.

S Check air intake opening, blower tubes or

vacuum tubes frequently, always with

engine stopped and spark plug

disconnected. Keep vents and discharge

tubes free of debris which can accumulate

and restrict proper air flow.

S Never place any object in air intake opening

as this could restrict proper air flow and cause

damage to the unit.

S Never use for spreading chemicals, fertilizers,

or other substances which may contain toxic

materials.

S To avoid spreading fire, do not use near leaf or

brush fires, fireplaces, barbecue pits,

ashtrays, etc.

CULTIVATOR SAF E TY

WARNING: Rotating tines can cause

serious injury. Keep away from rotating tines.

Stop the engine and disconnect the spark plug

before unclogging tines or making repairs.

WARNING: Inspect the area to be

cultivated before starting the unit. Remove all

debris and hard and sharp objects such as

rocks, vines, branches, rope, string, etc.

S Avoid heavy contact with solid objects that

might stop the tines. If heavy contact occurs,

stop the engine and inspect the unit for

damage.

S Never operate the cultivator without the tine

co ver in place an d properly secured.

S Keep the tines and guard clear of debris.

S After striking a foreign object, stop the

engine, disconnect the spark plug and

inspect the cultivator for damage. Repair

before restarting.

S Disconnect attachment from the drive engine

before cleaning the tines with a hose and

water to remove any build--up. Oil the tines to

prevent rust.

S Always wear gloves when servicing or

cleaning the tines. The tines become very

sha rp fro m use.

S Do not run unit at high speed unless

cultivating.

HEDGE TRIMMER SAFETY

DANGER: RISK OF CUT; KEEP

HANDS A WA Y FROM BL ADE -- Bla d e mo ve s

momentarily after the trigger is released or the

engine is turned of f. Do not attempt to clear

away cut material when the blade is in motion.

Make sure engine is stopped, the spark plug

wire is disconnected, and the blade has stopped

moving before removing jammed material from

the cutting blade. Do not grab or hold the unit by

the cutting blade.

WARNING: Inspect the area before

starting the unit. Remove all debris and hard

objects such as rocks, glass, wire, etc. that

can ricochet, be thrown, or otherwise cause

injury or damage during operation.

S Do not use a cutting blade that is bent,

warped, cracked, broken or damaged in any

other way. Have worn or damaged parts

replaced by an authorized service dealer.

S Always keep unit in front of your body.

Keep all parts of your body away from the

cutting blade.

S Keep the cutting blade and air vents clear of

debris.

POLE PRUNER SAFETY

WARNING: The reciprocating blade/

rotating chain can cause severe injury. In-

spect the unit before use. Do not operate unit

with a bent, cracked or d ull blade or dull chain.

Keep away from the blade/chain.

WARNING: The reciprocating blade/

rotating chain is sharp. Do not touch. To pre-

vent serious injury , always stop engine and

ensure blade/chain has stopped moving, dis-

connect spark plug, and wear gloves when

changing or handling the blade or chain.

WARNING: A coasting blade/rotat-

ing chain can cause injury while it continues to

move after the engine is stopped. Maintain

proper control of the unit until the blade/chain

has completely stopped moving. Keep

hands, face and feet at a distance from all

moving parts. Do not attempt to touch or stop

the blade or chain when it is moving.

WARNING: Falling objects can

cause severe head injury. Wear head protec-

tion when operating this unit with a pole prun-

er attachment.

WARNING: To prevent serious injury ,

do not use more than one boom extension with

a pole pruner attachment.

WARNING: Keep the pruner away

from power lines or electrical wires.

S Only use for pruning limbs or branches up

to 4 inches (10 cm) in diameter.

S Do not operate the unit faster than the

speed needed to prune. Do not run the unit

at high speed when not pruning.

S Always stop the unit when work is delayed

or when walking from one cutting location to

another.

S If you strike or become entangled with a

foreign object, stop the engine immediately

and check for damage. Have any damage

repaired by an authorized service dealer

before attempting further operations.

Discard blades that are bent, warped,

cracked or broken.

S Stop the unit immediately if you feel excessive

vibration. Vibration is a sign of trouble. Inspect

thoroughly for loose nuts, bolts or damage

before continuing. Contact an authorized

service dealer for repair or replacement of

affected parts as necessary.

SNOW THROWER SAFETY

WARNING: Keep hands and feet

away from the rotor when starting or running

the engine. Never attempt to clear the rotor

with the engine/motor running. Stop engine

and disconnect spark plug before unclogging

snow or debris from discharge chute or when

adjusting vanes.

WARNING: Never lean over dis-

charge chute. Rocks or debris could be

thrown into the eyes and face and cause seri-

ous injury or blindness.

WARNING: Inspect the area where

the unit is to be used. Remove objects that

could be thrown or damage the unit. Some

objects may be hidden by fallen snow -- be

alert for the possibility.

S Direct material discharge away from glass

enclosures, automobiles, etc.

S Do not run engine at high speed while not

removing snow .

S Be attentive when using the snowthrower ,

and stay alert for holes in the terrain and other

hidden hazards.

S Make sure the rotor will spin freely before

attaching the snowthrower to the powerhead.

S If the rotor will not rotate freely due to frozen

ice, thaw the unit before thoroughly before

attempting to operate under power .

S Keep the rotor clear of debris.

S Do not throw snow near other people. The

snow thrower could propel small objects at

high speed causing injury.

S After striking a foreign object, stop the

engine, disconnect spark plug and inspect

the snowthrower for damage and repair if

necessary before restarting unit.

S Never operate the snowthrower near glass

enclosures, automobiles and trucks.

S Never attempt to use the snowthrower on a

roof.

S Never operate the snowthrower near

window wells, dropoffs, etc.

S Never discharge snow onto public roads or

near moving traffic.

S Clear snow from slopes by going up and

down; never across. Use caution when

changing directions. Never clear snow

from steep slopes.

S Let snowthrower run for a few minutes after

clearing snow so moving parts do not

freeze.

S Look behind and use care when backing up.

Exercise caution to avoid slipping or falling,

especially when operating in reverse.

S Know how to stop quickly.

MAINTENANCE

WARNING: Disconnect the spark

plug before performing maintenance except

for carburetor adjustments.

HELPFUL TIP

IMPORT ANT: Have all

repairs other than the rec-

ommended maintenance

described in the instruction

manual performed by an

authorized service dealer.

If any dealer other than an authorized

service dealer performs work on the

product, Poulan PRO may not pay for

repairs under warranty. It is your re-

sponsibility to maintain and perform

general maintenance.

CHECK FOR LOOSE

FA STENERS AND PARTS

S Spark Plug Boot

S Air Filter

S Housing Screws

S Assist Handle Screw

S Debris Shield

CHECK FOR DAMAGED OR

WORN PARTS

Contact an authorized service dealer for re-

placement of damaged or worn parts.

S ON/STOP Switch -- Ensure ON/STOP

switch functions properly by pushing and

releasing the switch. Make sure engine

stops. Wait 5 seconds before attempting to

restart unit to allow switch to reset. Restart

engine and continue.

S Fuel Tank -- Discontinue use of unit if fuel

tank shows signs of damage or leaks.

S Debris Shield -- Discontinue use of unit if

debris shield is damaged.

INSPECT AND CLEAN UNIT ANDDE-

CALS

S After each use, inspect complete unit for

loose or damaged parts. Clean the unit and

decals using a damp cloth with a mild deter-

gent.

S Wipe off unit with a clean dry cloth.

CLEAN A IR F ILTER

A dirty air filter decreases engine perform-

ance and increases fuel consumption and

harmful emissions. Always clean after every

5 hours of operation.

1. Clean the cover and the area around it to

keep dirt from falling into the carburetor

chamber when the cover is removed.

2. Loo sen knob by turning counterclock-

wise. Remove air filter cover and air filter.

NOTE: To avoid creating a fire hazard or

producing harmful evaporative emissions, do

not clean filter in gasoline or other flammable

solvent.

3. Wash the filter in soap and water.

4. Allow filter to dry.

5. Replace parts.

ir Filter

Air Filter Cover

Knob

INSPECT MUFFLER AND SPARK

ARRESTING SCREEN

WARNING: The muffler on this prod-

uct contains chemicals known to the State of

California to cause cancer .

As your unit is used, carbon deposits build up

on the muffler and spark arresting screen and

must be removed to avoid creating a fire haz-

ard or affecting engine performance.

For normal homeowner use, the muffler and

spark arresting screen will not require any

service. After 50 hours of use, we recom-

mend that your muf fler be serviced or re-

placed by an authorized service dealer.

REPLACE SPARK PLUG

Replace the spark plug each year to ensure

the engine starts easier and runs better. Set

spark plug gap at 0.025 inch (0.6 mm). Igni-

tion timing is fixed and nonadjustable.

NOTE: This spark ignition system complies

with the Canadian standard ICES--002.

1. Twist, then pull off spark plug boot.

2. Remove spark plug from cylinder and

discard.

3. Replace with Champion RCJ-6Y spark

plug and tighten securely with a 3/4 inch

(19 mm) socket wrench.

4. Reinstall the spark plug boot.

SERVICE AND ADJUSTMENTS

REPLACING THE LINE

For unit to operate properly , the cutting line

should be replaced when line becomes worn to

less than 3 inches (7.5 cm) in length from the

edge of the line exit tunnels on each side of the

cutting head.

1. Remove and discard worn line before

installing new line.

2. Use only 0.115 inch (3 mm) diameter

Poulan PRO brand cut length line.

3. Insert one end of the line through the

positioning tunnel.

4. Continue to feed line through tunnel until

line is centered (leaving equal amounts

on each side). See illustration below.

Positioning

tunnel

5. Insert ends of line one at a time through

the line exit tunnels.

6. Pull the line and make sure the line is ex-

tended fully through the tunnels.

Line exit

tunnel

Line exit

tunnel

7. Correctly installed line will be the same

length on both ends.

BLADE REPLACEMENT

Refer to the ASSEMBLY section for blade re-

placement instructions and illustrations.

CARBURETOR IDLE SPEED

ADJUSTMENT

WARNING: Keep others away when

making idle speed adjustments. The trimmer

head, blade or any optional attachment will be

spinning during most of this procedure. W ear

your protective equipment and observe all safe-

ty precautions. After making adjustments, the

trimmer head, blade or any optional attachment

must not move/spin at idle speed.

The carburetor has been carefully set at the

factory . Adjustments may be necessary if you

notice any of the following conditions:

S Engine will not idle when the throttle is

released.

S The trimmer head, blade or optional

attachment moves/spins at idle.

Make adjustments with the unit supported so

the cutting attachment is off the ground and

will not make contact with any object. Hold

the unit by hand while running and making ad-

justments. Keep all parts of your body away

from the cutting attachment and muffler.

To adjust idle speed:

Allow engine to idle. Adjust speed until engine

runs without trimmer head, blade or optional

attachment moving or spinning (idle too fast)

or stalling (idle speed too slow).

S Turn idle speed screw clockwise to

increase engine speed if engine stalls or

dies.

S Turn idle speed screw counterclockwise to

decrease engine speed if trimmer head,

blade or optional attachment moves or

spins at idle.

WARNING: Recheck the idle speed

after each adjustment. The trimmer head,

blade or optional attachment must not move

or spin at idle speed to avoid serious injury to

the operator or others.

Air Filter

Cover

Idle Speed Screw

If you require further assistance or are unsure

about performing this procedure, contact an

authorized service dealer or call

1--800--554--6723.

STORAGE

WARNING: Perform the following

steps after each use:

S Allow engine to cool before storing or trans-

porting.

S Store unit and fuel in a well ventilated area

where fuel vapors cannot reach sparks or

open flames from water heaters, electric

motors or switches, furnaces, etc.

S Store unit with all guards in place. Position

unit so that any sharp object cannot acci-

dentally cause injury.

S Store unit and fuel well out of the reach of

children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if

it will not be used for 30 days or more.

If your unit is to be stored for a period of time:

S Clean the entire unit before lengthy

storage.

S Store in a clean dry area.

S Lightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA-

TION section of this manual, see message la-

beled IMPORTANT regarding the use of ga-

sohol in your engine.

Fuel stabilizer is an acceptable alternative in

minimizing the formation of fuel gum deposits

during storage. Add stabilizer to the gasoline

in the fuel tank or fuel storage container . Fol-

low the mix instructions found on stabilizer

container. Run engine at least 5 minutes after

adding stabilizer.

HELPFUL TIP

During storage of your gas/

oil mixture, the oil will sepa-

rate from the gas.

We recommend that you

shake the gas can weekly

to insure proper blending of

the gas and oil.

ENGINE

S Remove spark plug and pour 1 teaspoon of

40:1, 2-cycle engine oil (air cooled) through

the spark plug opening. Slowly pull the

starter rope 8 to 10 times to distribute oil.

S Replace spark plug with new one of recom-

mended type and heat range.

S Clean air filter .

S Check entire unit for loose screws, nuts,

and bolts. Replace any damaged, broken,

or worn parts.

S At the beginning of the next season, use

only fresh fuel having the proper gasoline to

oil ratio.

OTHER

S Do not store gasoline from one season to

another.

S Replace your gasoline can if it starts to rust.

TROUBLE CAUSE REMEDY

Engine will not

start.

1. Engine flooded.

2. Fuel tank empty.

3. Spark plug not firing.

4. Fuel not reaching

carburetor.

5. Carburetor requires

adjustment.

1. See “Starting a Flooded Engine” in

Operation Section.

2. Fill tank with correct fuel mixture.

3. Install new spark plug.

4. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

5. Contact an authorized service dealer .

Engine will

not idle

properly.

1. Carburetor requires

adjustment.

2. Crankshaft seals worn.

3. Compression low.

1. See “Carburetor Idle Speed Adjustment”

in Service and Adjustments Section.

2. Contact an authorized service dealer .

3. Contact an authorized service dealer .

1. Air filter dirty.

2. Spark plug fouled.

3. Carburetor requires

adjustment.

4. Carbon build-up on

muffler outlet screen.

5. Compression low.

Engine will not

accelerate,

lacks power,

or dies under

a load.

1. Clean or replace air filter.

2. Clean or replace plug

and regap.

3. Contact an authorized service dealer .

4. Contact an authorized service dealer .

5. Contact an authorized service dealer .

Engine

smokes

excessively .

1. Fuel mixture incorrect.

2. Air filter dirty .

3. Carburetor requires

adjustment.

1. Empty fuel tank and refill with

correct fuel mixture.

2. Clean or replace air filter.

3. Contact an authorized service dealer .

Engine runs

hot.

1. Fuel mixture incorrect.

2. Spark plug incorrect.

3. Carburetor requires

adjustment.

4. Carbon build-up on

muffler outlet screen.

1. See “Fueling Engine” in Operation

section.

2. Replace with correct spark plug.

3. Contact an authorized service dealer .

4. Contact an authorized service dealer .

WARNING: Always stop unit and disconnect spark plug before performing all of the

recommended remedies below except remedies that require operation of the unit.

TROUBLESHOOTING TAB LE

Page is loading ...

Poulan Pro 952711951 User manual

Brand: Poulan Pro

Model: 952711951

Category: Power tools

Type: User manual

This manual is also suitable for

Download PDF

report

Poulan Pro 952711951 User manual

This manual is also suitable for

Poulan Pro 952711951 User manual

Related papers

Other documents