Prolux PROCOM_6000 User manual

6000 / 7000

Upright Vacuum

Instruction Manual

2

Contents

Safety Instructions ----------------------------------------------------------------2-5

Included Parts --------------------------------------------------------------------6-7

Assembly Instructions ------------------------------------------------------------8-10

Operating Instructions ------------------------------------------------------------10-13

Using the Tools -------------------------------------------------------------------13-15

Maintenance ----------------------------------------------------------------------16-20

Warranty Information ------------------------------------------------------------17

Congratulations on the purchase of your Prolux 6000 or 7000 Vacuum!

This manual covers the Prolux model 6000 and 7000. The Prolux 6000 & 7000

models are high end vacuums that are attractive, powerful and designed to last for

many years to come.

• High End Upright Vacuums - MSRP of $599 & $799

• 5 Year Warranty on 7000 model and 3 Year Warranty on 6000 model

• Sealed HEPA filtration– Model 6000 (washable) Model 7000 (TRUE HEPA)

• On board tools- Model 7000 on board tools are stored on the vacuum

• Bag Full Indicator and Thermal Protected Motor on model 7000

• Noise Insulated for quiet easy vacuuming of all types of floor surfaces

• An Amazon 107 cubic feet per minute of Air Flow

• Powerful 12 Amp Deep Cleaning Motor.

Customer’s Record

This model number and serial number of your vacuum cleaner is located on the

underside of the unit. Please record these numbers in the spaces provided below

3

and keep this booklet as a permanent record of your purchase.

Model Number: _______________________________________________________

Serial Number: _______________________________________________________

Date Purchased: ______________________________________________________

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions before using this appliance

When using your vacuum cleaner, basic precautions should always be followed,

including the following:

WARNING-To reduce the risk of fire, electric shock, or injury:

1. Before connecting the power cord of your new vacuum cleaner to an

electrical outlet, check the voltage rating. Your power source should

correspond with the voltage rating plate on the underside of the vacuum

cleaner. Use only household ac outlets. Never use dc power sources. If

you are unsure of the voltage supply in your area, consult a qualified

electrician. Connecting the vacuum cleaner to a higher voltage than

indicated in these instructions may result in damage to the vacuum cleaner

and/or personal injury.

2. Do not leave the vacuum cleaner plugged in unattended. Unplug from the

outlet when not in use or before servicing.

3. Always unplug before changing the lamp. Replace the bulbs with the same

type rating.

4. DO NOT USE OUTDOORS OR ON WET SURFACES.

5. Do not allow the vacuum cleaner to be used as a toy. Pay close attention

when using by or near children.

6. Use only as described in this manual. Use only manufacturer’s

recommended attachments.

7. Do not use the vacuum cleaner if the cord or plug is damaged.

8. If the vacuum cleaner is not working as it should, has been dropped,

damaged, left outdoors or immersed in water, return it to an authorized

4

vacuum cleaner dealer for repair.

9. Do not pull or carry by the cord, use the cord as a handle, run appliance

over cord, close a door on the cord, or pull the cord around sharp edges or

corners. Keep the cord away from heater surfaces.

10. Do not unplug by pulling on the cord. To unplug, grasp the plug, not the

cord, and pull out of the outlet.

11. Do not handle the plug or the vacuum cleaner with wet hands.

12. Do not put objects into the openings. Do not use with any openings

blocked. Keep free of dust, lint, hair, and anything that may reduce air flow.

13. Do not allow loose clothing, hair, fingers or other parts of the body to come

into contact with any openings or moving parts of the vacuum cleaner.

14. Do not vacuum anything that is burning or smoking, such as cigarettes,

matches, or hot ashes.

15. Do not use without the dust bag and/or filters in place.

16. Always turn off all controls before unplugging the vacuum cleaner or

before connecting or disconnecting either the hose or the agitating brush.

17. Use extra care when cleaning on stairs.

18. Do not use the vacuum cleaner to pick up flammable or combustible

liquids, such as gasoline, or use in areas where they may be present. This

could impair the electrical safety of the vacuum cleaner. This applies to

freshly shampooed carpets, too. Wait until they are dry.

19. Floor attachments and accessories must not be used at head level to

avoid the risk of injury to eyes and ears.

20. Do not touch the agitating brush when in use.

21. Prolux vacuum cleaner dust bags are disposable and are intended to be

used only once. Do not attempt to reuse them.

22. DO NOT USE ON PEOPLE OR ANIMALS.

23. This appliance is for use on a nominal 120-volt circuit and has a grounding

attachment plug that looks like the plug illustrated in sketch A in Figure 20.

Make sure that the appliance is connected to an outlet having the same

configuration as the plug. No adapter should be used with this appliance.

5

WARNING

Household Models 6000 & 7000

NOTE: As a safety feature and to reduce risk of damage, injury or electric shock, this

vacuum cleaner is equipped with a polarized alternating current line plug (one blade

wider than the other). This plug will fit in a polarized outlet only one way. If the plug

does not fit fully in the outlet, reverse the plug. If the plug still fails to fit, contact a

qualified electrician to replace the outlet. Do not attempt to alter the plug thus

defeating the safety purpose of the polarized plug.

SAVE THESE INSTRUCTIONS.

Models 6000 & 7000 are intended for household and light office use only.

6

FEATURE COMPARISON CHART

Feature/Mod

el

Input

(amps)

Power

Control

Full Bag

Indicator

Head

Light

Cord

Length

6000

12.0

1-Speed

No

Yes

25 feet

7

FEATURE COMPARISON CHART

Feature/Model

Input

(amps)

Power

Control

Full Bag

Indicator

Head

Light

(LED)

Cord

Length

7000

12.0

1-Speed

Yes

30 feet

8

How To Use Friction Fit Cleaning Tools: Model 6000

9

The tools are connected by friction fit. Meaning to attach simply shove

together and twist firmly. To remove simply untwist.

10

EASY ASSEMBLY INSTRUCTION

Step One: Attaching the Handle

1. Remove handle screw.

2. Insert handle into top of dust cover with handle switch facing forward (Model

7000 only)

3. Align small hole on handle with screw hole in dust cover. Insert screw and

tighten securely (All models).

4. Turn upper cord storage hook to upright position and wind cord between upper

and lower hooks for storage.

5. To quick-release cord, simply rotate upper hook downward and cord will drop

for immediate use.

How To Release Power Cord:

1. The upper cord storage hook has a quick-release action. To release the cord,

rotate the hook downward and the cord will drop off the handle for immediate

use.

2. Return the hook to upright position before attempting to rewind the cord.

11

Replacing the Dust Bag:

*Remember: Always have a dust bag installed when operating your vacuum cleaner.

Replace with a genuine dust bag when full.

1. Push down on knob at top of dust cover to open compartment.

2. Pull cardboard bag collar off holder. Remove and discard used dust bag.

3. Slide clean replacement bag collar onto holder. The bag lever must be

positioned behind bag collar. Never pull up the lever, rather, push it down with

dust bag.

4. Close dust cover by reinserting tab on end into groove on housing and snap

shut.

Checking the Secondary Filter:

*Important: The secondary filter protects the motor from dust and dirt.

1. Check for accumulated dust and dirt when replacing dust bag. Filter may

be cleaned as needed.

2. I

f

r

e

p

l

a

c

e

m

e

n

t

12

is needed, release the right tab on underside of bag supporter. Lift and

rotate bag supporter to remove.

3. Remove secondary filter

from bottom of dust

compartment.

4. Replace secondary filter

with new filter.

5. Reinstal

l bag

support

er.

Checking the Post Filter:

The auxiliary post filter captures fine dust particles and purifies air exiting your

vacuum cleaner.

Change or clean the post filter with every third dust bag replacement, or as

needed.

1. Depress handle release pedal to drop vacuum cleaner to low position.

2. Push knob at side of post filter to remove post filter cover.

3. Remove soiled filter and replace with new one. (Do not wash.)

13

Special Features Make Your Vacuum a Peak Performer!

ON/OFF Switch:

Model 6000 Vacuum Cleaners have a simple toggle switch on the dust compartment.

Push down --- to start. Push down O to stop.

Model 7000 is equipped with a convenient handle slide switch to turn power ON and

OFF.

Automatic Self-Adjusting Carpet Nozzle:

Your vacuum can float evenly over varying carpet pile lengths. The carpet nozzle

raises itself instantly and automatically.

Full Bag Indicator Light: Model 7000

A warning light located on the front of the switch cover

below the easy carry handle will activate when the dust bag is full, or if the vacuum

cleaner is clogged. Replace bag if full. To check for

clogs, unplug vacuum cleaner and inspect agitator area

(see “Removing the bottom plate” on page 14) hose

and attachment inlet.

Special note: when cleaning with attachments, disregard the full bag indicator light.

Normal airflow restrictions occur with attachment cleaning and may trigger a false

signal.

When turning on the vacuum cleaner while the full bag indicator light is on and the

vacuum cleaner will not start, check to see if the dust bag is installed correctly.

Handle Adjustments:

The handle of this vacuum cleaner can be set to any of three positions: upright,

middle, or low. To release the handle, step on the pedal at the left rear corner of the

vacuum cleaner.

1. Upright position: handle locks in this position for vacuum cleaner storage. The

handle should always be in the upright position when cleaning tools are used.

2. Middle position: this position is for normal cleaning. While in the middle

position, the front of the nozzle can be raised by lowering the handle in order

to cross room thresholds.

3. Low position: this position is used for cleaning under most furniture.

14

On-board Cleaning Tools: Model 7000

Model 7000 is equipped with state-of-the-

art on-board cleaning tools including:

• 2 piece telescoping wand

• Extension wand

• Crevice tool

• Dusting brush

• Upholstery tool

To use:

1. Remove 2 piece telescoping wand from wand retainer.

2. Connect 2 piece telescoping wand to cleaning tools. Unlock wand collar to

extend wand to desired length.

3. Attach selected cleaning tool to wand. (Tools may also be attached directly to

flexible hose cuff, omitting extension wand.)

4. Cleaning tools are stored conveniently on back of the vacuum cleaner body.

Snap tools back into their appropriate places.

Available Optional Cleaning Tools:

A deluxe attachment set is available for models without on-board tools. It

contains:

1. Hose assembly

2. Curved wand

3. 3 piece telescoping wand

4. Dusting brush

5. Crevice tool

15

6. Upholstery brush

Connecting the Optional Hose Assembly:

Simply lift the lid of the cleaning attachment opening located at the back of your

vacuum cleaner and insert the hose end until it fits snugly.

Connecting the Tools:

Connect any of the cleaning tools to the extension wand or curved wand and twist for

secure fit. Twist and pull apart to remove.

Suction Control: Model 6000 & 7000

To reduce

suction when

16

cleaning draperies, small rugs, etc., move the suction control slide on the back of the

vacuum cleaner by increasing the opening until desired suction power is achieved.

Close for normal vacuum operation.

Note: Model 7000 full-bag indicator light will not operate while suction control is in

open position.

Replacing Headlight Bulb:

Step One: Removing the bottom plate

*Caution: First unplug the vacuum cleaner from the electrical outlet.

1. Use handle release pedal to place vacuum in Low position. Turn vacuum over

to expose underside.

2. Slide the two latches inward to release bottom plate.

Step Two: Changing the Headlight Bulb

Model 6000

1. Use any standard bayonet base appliance bulb rated 120-130 V, 15 W.

2. Remove the two frame screws.

3. Carefully lift out the entire headlight assembly.

4. Remove bulb by pushing in lightly and turning counterclockwise.

17

5. Replace with new bulb, turn clockwise.

6. Reinsert the headlight assembly back into the nozzle housing being careful

not to pinch or re-arrange any wires and insert the two frame screws.

7. Reinsert bottom plate making certain that the hinges are in place on the front

of the housing before sliding the two latches outward to fasten.

Resetting the Thermal Switch:

Model 7000

The Thermal Switch protects the motor from overheating. If the motor stops due to

prolonged use, follow steps 1-5.

1. Unplug the power cord.

2. Set power switch on handle to OFF position.

3. Wait about 10 min. to let the motor cool down.

4. Push the reset button lightly to the stop position.

5. Restart your vacuum cleaner.

Replacing the Drive Belt:

18

1. Unplug the power cord.

2. Turn the unit over and remove the bottom plate as previously described

under “Replacing Headlight Bulb Step One” on previous page.

3. Lift the rear belt cover up and back.

4. Remove the vented support fitting, noting position.

5. Remove agitator unit and worn out belt.

6. Loop new belt around motor drive shaft and agitator pulley.

7. Reinsert agitator unit into housing, making sure the two ends are

positioned in the support guide.

8. Turn agitator unit by hand to install new belt onto guide, making sure

belt is not twisted and rotating parts move smoothly.

9. Reinsert the vented support fitting and lower rear belt cover.

10. Reinsert bottom plate making certain that the hinges are in place on the

front of the housing before sliding the two latches outward to fasten.

19

Changing the Agitator Brushes:

Replace agitator brushes when they are worn or when the bristles do not touch a

card held across the base plate. Replace all four brushes at the same time to

maintain maximum cleaning performance.

Remove agitator, start as described on previous page, Section 1 to 4.

1. Turn on end cap and remove.

2. Remove the agitator shaft.

3. Remove and replace the brushes on the shaft.

4. Reinstall the pulley and agitator holder making sure they are inserted

completely and firmly.

5. Reinstall remaining parts.

6. Reinstall agitator assembly as described previously in Step 6-10 on previous

page.

20

For Best Performance:

1. Keep machine and all accessories clean and in proper operating condition.

2. Change dust bags and filters as recommended to maintain optimum cleaning

efficiency.

3. Always use genuine dust bags and filters. Use of other products may result in

unsatisfactory cleaning or filtration performance. Filtration products are

designed for maximum performance.

4. Have your vacuum cleaner checked regularly by your Authorized Vacuum

Cleaner Dealer.

5. Use only vacuum cleaner authorized dealers for repairs parts or service.

6. Carefully store machine in a dry area.

7. For optimum cleaning performance and safety, follow your Owner’s Manual.

Keep this manual in a safe place for future reference.

Page is loading ...

Prolux PROCOM_6000 User manual

This manual is also suitable for

Prolux PROCOM_6000 User manual

Related papers

Other documents