Hitachi CM 5SB Technical Data And Service Manual

Cutting or scribing concrete

Cutting or scribing tile

Cutting or scribing stone

Cutting or scribing roof tile

[ NEW FEATURES ]

Class-top dust collecting performance

High stability with wider base

(for the Models CM 9SR/CM 9UBY)

Pocket guide

(for the Models CM 9SR/CM 9UBY)

*Other than the above features, the Models CM 5SB,

CM 9SR and CM 9UBY have the features (selling

points) common to the base Models G 13SB3,

G 23SR and G 23UBY respectively.

The new cutters Models CM 5SB, CM 9SR and CM 9UBY are developed based on the disc grinders Models

G 13SB3, G 23SR and G 23UBY respectively, and the main bodies are common to those of the base models.

Therefore, main features of these new cutters are common to the base models. In addition, each of the Models

CM 5SB, CM 9SR and CM 9UBY is equipped with a dust collection cover (for diamond wheel) as a standard

accessory.

PRODUCT NAME

Hitachi Cutter

Models 125 mm (5”) CM 5SB

230 mm (9”) CM 9SR

230 mm (9”) CM 9UBY

MARKETING OBJECTIVE

APPLICATIONS

SELLING POINTS

International Sales Division

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR

IMPROVEMENT.

LIST Nos.

CM 5SB: E716

CM 9SR: E715

CM 9UBY: E714

Dec. 2007

CM 5SB

CM 9UBY

REMARK:

For more information about HANDLING INSTRUCTIONS, visit our website at:

http://www.hitachi-koki.com/manual_view_export/

Throughout this TECHNICAL DATA AND SERVICE MANUAL, a symbol(s) is(are) used in the place of

company name(s) and model name(s) of our competitor(s). The symbol(s) utilized here is(are) as follows:

Competitors

Symbols Utilized

Company Name Model Name

CHILTI

DC125-S

DC 230-S/EX

CONTENTS

Page

SELLING POINT DESCRIPTIONS ----------------------------------------------------------------------------------------- 1

SPECIFICATIONS -------------------------------------------------------------------------------------------------------------- 2

1. Specifications

--------------------------------------------------------------------------------------------------------------------------------- 2

COMPARISONS WITH SIMILAR PRODUCTS-------------------------------------------------------------------------- 3

1. Specifications comparisons

---------------------------------------------------------------------------------------------------------- 3

PRECAUTIONS IN SALES PROMOTION-------------------------------------------------------------------------------- 4

1. Safety instructions

------------------------------------------------------------------------------------------------------------------------- 4

REPAIR GUIDE------------------------------------------------------------------------------------------------------------------ 5

1. Precautions in disassembly and reassembly-------------------------------------------------------------- 5

STANDARD REPAIR TIME (UNIT) SCHEDULES---------------------------------------------------------------------- 7

Assembly diagram for CM 5SB

Assembly diagram for CM 9SR

Assembly diagram for CM 9UBY

Base Roller

Other than the following, the Models CM 5SB, CM 9SR and CM 9UBY have the features (selling points)

common to the base Models G 13SB3, G 23SR and G 23UBY respectively. Refer to each TECHNICAL

DATA AND SERVICE MANUAL of the base models for details of the selling points.

Class-top dust collecting performance

Each of the Models CM 5SB, CM 9SR and CM 9UBY is equipped with a high-performance dust collection

cover as a standard accessory. Following is a comparison data on dust collection rate when the cutting

depth is 10 mm. The dust collection rate of the Models CM 9SR and CM 9UBY is 4% higher than that of C,

and the Model CM 5SB is 10% higher than that of C.

High stability with wider base (For the Models CM 9SR/CM 9UBY)

Each base of the Models CM 9SR and CM 9UBY is

1.3 times wider than that of C for more stable cutting

operation.

Maker

HITACHI

Model CM 9SR/CM 9UBY

Width of base

80 mm

(3-5/32”)

60 mm

(2-23/64”)

Pocket guide (For the Models CM 9SR/CM 9UBY)

Each of the Models CM 9SR and CM 9UBY is

equipped with a pocket guide at the tip of the base.

The movable pocket guide is retracted in the base as

cutting proceeds. The pocket guide prevents dust from

scattering to the outside at the start of cutting for more

efficient dust collection.

SELLING POINT DESCRIPTIONS

Pocket guide

Diamond wheel

Dust

100

CM 9SR/UBY CM 5SB C

Dust collection rate (%)

10 %

4 %

1. Specifications

Model

CM 5SB CM 9SR CM 9UBY

Max. cutting depth

30 mm (1-3/16”) 60 mm (2-23/64”) 60 mm (2-23/64”)

External

dia.

125 mm (5”) 230 mm (9”)

Thickness

2.0 mm (5/64”) 2.5 mm (3/32”)

Diamond

wheel

size

Internal dia.

22.2 mm (7/8”) 22.2 mm (7/8”)

Power source

AC single phase 50 or 60 Hz

Voltage and power

input

No-load speed

110 V,120 V: 10,000/min

230 V: 11,000/min

6,600/min 6,600/min

Type of motor

AC single phase commutator motor

Enclosure

Housing (black),

handle, tail cover (green)

Gear cover, packing gland --------------------------- Aluminum alloy diecasting

Type of switch

Slide switch Trigger switch

Net

2.9 kg (6.4 lbs.) 7.7 kg (17.0 lbs.) 8.1 kg (17.9 lbs.)

Weight

Gross

4.6 kg (10.2 lbs.) 12.8 kg (28.3 lbs.) 13.7 kg (30.2 lbs.)

Type of packing

Plastic case

Standard accessories

Side handle ---------- 1

Wrench --------------- 1

Adapter --------------- 1

Case ------------------- 1

Pipe handle --------------- 1

Wrench --------------------- 1

Adapter --------------------- 1

Case ------------------------ 1

Optional accessories

Diamond wheel

· Segment type

(Code No. 994325, 307007)

· Wave-shape type

(Code No. 994326)

Diamond wheel

Segment type (Code No. 994275, 994278)

Wave-shape type (Code No. 994276)

: Net weight excludes cord and diamond wheel.

SPECIFICATIONS

Voltage

(V)

Current

(A)

Power

input

(W)

110 8.0 830

120 8.0 910

230 6.0 1,300

Voltage

(V)

Current

(A)

Power

input

(W)

110 19.0 2,000

230 9.2 2,000

Voltage

(V)

Current

(A)

Power

input

(W)

110 21.8 2,400

230 12.0 2,600

------------ Polyamide resin with glassfiber

1. Specifications comparisons

(Superior specifications:

)

Maker HITACHI

Model name CM 5SB

Cutter dia. 125 mm (5”) 125 mm (5”)

Power input* 1,300 W 1,400 W (Electronic)

Max. power output* 1,900 W 2,100 W

No-load speed* 11,000/min 11,000/min

No-load sound pressure level 86 dB (A) 86 dB (A)

Max. cutting depth 30 mm (1-3/16”) 28 mm (1-7/64”)

Dust collection cover Standard accessory Optional accessory

Width of base 33.5 mm (1-5/16”) 41 mm (1-39/64”)

Weight 2.9 kg (6.4 lbs.) 2.6 kg (5.7 lbs.)

*: Depends on market.

Maker HITACHI

Model name CM 9SR CM 9UBY

Cutter dia. 230 mm (9”) 230 mm (9”) 230 mm (9”)

Power input* 2,000 W 2,600 W 2,500 W

Max. power output* 3,300 W 4,600 W 4,200 W

No-load speed* 6,600/min 6,500/min

No-load sound pressure level 89 dB (A) 95 dB(A)

Max. cutting depth 60 mm (2-23/64”) 60 mm (2-23/64”)

Dust collection cover Standard accessory Standard accessory

Pocket guide Provided Not provided

Width of base 80 mm (3-5/32”) 60 mm (2-23/64”)

Weight 7.7 kg (17.0 lbs.) 8.1 kg (17.9 lbs.) 7.0 kg (15.5 lbs.)

*: Depends on market.

COMPARISONS WITH SIMILAR PRODUCTS

1. Safety instructions

In the interest of promoting the safest and most efficient use of the Models CM 5SB, CM 9SR and CM9UBY

Cutters by all of our customers, it is very important that at the time of sale, the salesperson carefully

ensures that the buyer seriously recognizes the importance of the contents of the Handling Instructions,

and fully understands the meaning of the precautions listed on the Name Plate.

A. Handling instructions

Although every effort is made in each step of design, manufacture and inspection to provide protection

against safety hazards, the dangers inherent in the use of any electric power tool cannot be completely

eliminated. Accordingly, general precautions and suggestions for the use of electric power tools, and

specific precautions and suggestions for the use of the Cutters are listed in the Handling Instructions to

enhance the safe and efficient use of the tool by the customer.

Salespersons must be thoroughly familiar with the contents of the Handling Instructions to be able to offer

appropriate guidance to the customer during sales promotion.

B. Caution on name plate

Each tool is provided with a Name Plate which contains the following basic safety precautions in the use of

the tool.

(1) For Europe

(2) For the U.S.A. and Canada (Model CM 5SB)

C. Precautions on usage

Never press the pushing button while the diamond wheel is rotating.

If the pushing button is pressed while the diamond wheel is rotating, the spindle will stop immediately.

In such a case, there is a danger that the wheel nut may be loosened so that the diamond wheel flies off

unexpectedly to cause possible serious injury.

PRECAUTIONS IN SALES PROMOTION

WARNING

To reduce the risk of injury, user must read and understand instruction manual.

Always use guards and wear eye protection.

Use only accessories rated at least 12000/min.

AVERTISSEMENT

Afin de reduire le risque de blessures, I'utilisateur doit lire et bien comprendre le mode

d'emploi.

Utilisez toujours un outil muni d'un protecteur et portez des lunettes on une visiere.

N'utilisez que des accessoires prevus pour au moins 12000/min.

Before attempting disassembly or reassembly, ensure without fail that the switch is turned off and the plug

is disconnected from the power source outlet.

1. Precautions in disassembly and reassembly

The [Bold] numbers in the description below correspond to the item numbers in the Parts Lists and the

exploded assembly diagrams for the Models CM 5SB, CM 9SR and CM 9UBY.

The main bodies of the Models CM 5SB, CM 9SR and CM 9UBY are common to those of the base Models

G 13SB3, G 23SR and G 23UBY respectively. Therefore, only the disassembly and reassembly procedures

of the newly designed dust collection cover unit are described below.

A. Dust Collection Aadapter Ass’y [65] (Model CM 5SB)

(1) Loosen the Knob Bolt M5 [66] and remove Cover

(A) [38].

(2) Loosen the Wheel Nut 5/8”-11UNC [37] using the

attached Wrench [502]. Remove the diamond

wheel and the Wheel Washer [30] together from

the Spindle [29].

(3) Loosen the two Machine Screws (W/Sp. Washer)

M5 x 16 (Black) [32] and remove the Dust

Collection Adapter Ass’y [65] (Dust Collector

Cover (A) [34]) from the Packing Gland [26].

(4) Loosen the Wing Nut M6 [41] and remove the

Sleeve [40], Bolt (Square) M6 x 20 [35] and Slide

Guide (A) [36] from Dust Collector Cover (A) [34].

REPAIR GUIDE

Disassembl

Diamond wheel

B. Dust Cover Ass’y [88] (Model CM 9SR) [92] (Model CM 9UBY]

The [Bold] numbers and the circled numbers in the descriptions below correspond to the item numbers in

the Parts List and the exploded assembly diagram of the Model CM 9SR. (The dust cover ass'y is common

to that of the Model CM 9UBY.)

(1) Loosen the Wing Nut M6 [48] and lower the

Base [68] in “G” direction.

(2) Loosen the two Knob Nuts [37] and remove

Cover (B) [35].

(3) Loosen the two Wheel Nuts M14 x 2 [59]

using the attached Wrench [502] and remove

the diamond wheel and Wheel Washer (A)

[58] together from the Spindle [13].

(4) Open the Lever [52] and loosen the Bolt

M8 x 22 [53] to remove the Dust Cover Ass’y

[88] (Wheel Guard Ass’y [56]) from the

Packing Gland [15].

(5) Loosen the two Wing Nuts M6 [48] and

remove the two Bolts (Square) M6 x 57 [41]

and the Sleeve [47] from the Wheel Guard

Ass’y [56].

(6) Remove the Hose Band [33] from the Dust

Duct [34] to remove the Adapter [38].

(7) Loosen the U-Nut (B) M8 [93]. Remove Bolt

(A) [57] from the Holder [61] to remove the

Wheel Guard Ass’y [56], Cover (A) [60] and

Dust Duct [34].

(8) Remove the eight Retaining Rings (E-Type)

for D7 Shaft [64] to remove the two Roller

Shafts [66] from the Base [68]. At this time,

remove the four Rollers [65], Holder [61] and

Pocket Guide

[63] together.

Reassembly can be accomplished by following the disassembly procedure in reverse.

Refer to each TECHNICAL DATA AND SERVICE MANUAL of the base Models G 13SB3 (List No. E271),

G 23SR (List No. E273) and G 23UBY (List No. E282) for precautions in disassembly and reassembly,

lubrication points and types and amounts of lubricant, tightening torque, and wiring diagram.

Reassembl

Diamond wheel

MODEL

Variable

Fixed

10 20 30 40 50 60

Work Flow

CM 5SB

General assembly

Carbon

Brush x 2

Spring x 2

Pushing

Button Switch

Cord Armor

Tail Cover

Cord

Dust Collection

Adapter Ass’y

Gear Cover

Ass’y

Pinion

Seal Ring (A)

Washer (C)

Ball Bearing

(629T12DD)

Rubber Ring

Bearing Cover

Armature

Ass’y

Dust Seal

Ball Bearing

(608VV)

Pushing Button

Lock Pin

Gear

Bearing

Cover (B)

Ball Bearing

(6201DD)

Felt Packing

Packing Gland

Spindle

Housing

Stator

Slide Bar

STANDARD REPAIR TIME (UNIT) SCHEDULES

MODEL

Variable

Fixed

10 20 30 40 50 60

Work Flow

CM 9SR

General assembly

Dust Cover

Ass’y

Handle (B)

Cord Armor

Gear Cover

Ass’y

Seal Plate

Handle (A)

Switch

Cord

Pinion

Seal Washer

Felt Packing

Ball Bearing

(6301VV)

Rubber Ring (B)

Bearing

Cover (A)

Armature

Dust Seal

Ball Bearing

(6000VV)

Bearing

Bushing

Gear

Housing Ass’y

Stator Ass’y

Bearing

Cover (B)

Ball Bearing

(6302VV)

Felt Packing

(B)

Packing Gland

Spindle

MODEL

Variable

Fixed

10 20 30 40 50 60

Work Flow

CM 9UBY

General assembly

Dust Cover

Ass’y

Handle (B)

Cord Armor

Gear Cover

Ass’y

Seal Plate

Handle (A)

Switch

Cord

Handle Damper

Seal Washer

Felt Packing

Ball Bearing

(6301VV)

Rubber Ring (B)

Bearing

Cover (A)

Armature

Dust Seal

Ball Bearing

(6000VV)

Bearing

Bushing

Gear (A) Ass’y

Retaining Ring

Coupling Cover

Housing Ass’y

Stator

Bearing

Cover (B)

Ball Bearing

(6302VV)

Felt Packing

(B)

Packing Gland

Spindle

LIST NO. E716

PART

CM 5SB

DESCRIPTION REMARKS

1 320-523 TAPPING SCREW D5X25 (BLACK) 4

3 321-737 GEAR COVER ASS'Y 1 INCLUD. 4, 20

4 301-943 LOCK PIN 1

5 949-558 NUT M8 (10 PCS.) 1

7 308-543 SEAL RING (A) 1

8 980-866 WASHER (C) 1

9 629-T12 BALL BEARING 629T12DDC3PS2-L 1

10 321-733 RUBBER RING 1

11 321-734 BEARING COVER 1

* 12 360-734C ARMATURE 110V 1

* 12 360-734U ARMATURE ASS'Y 120V 1 INCLUD. 9, 16, 17

* 12 360-734E ARMATURE 230V-240V 1

13 321-732 FAN GUIDE 1

14 982-021 HEX. HD. TAPPING SCREW D4X70 2

* 15 340-645C STATOR 110V 1

* 15 340-645D STATOR 120V 1

* 15 340-645E STATOR 230V 1

16 315-877 DUST SEAL 1

17 608-VVM BALL BEARING 608VVC2PS2L 1

18A 329-054 GEAR AND PINION SET 1

19 303-255

SEAL LOCK SCREW (W/SP. WASHER) M4X10 2

20 301-944 PUSHING BUTTON 1

22 991-207 SEAL LOCK SCREW (W/SP. WASHER) M4X8 3

23 936-680 BEARING COVER (B) 1

24 620-1DD BALL BEARING 6201DDCMPS2L 1

25 308-546 FELT PACKING 1

26 308-545 PACKING GLAND 1

27 307-046

SEAL LOCK SCREW (W/SP. WASHER) M5X16 4

28 944-109 FEATHER KEY 3X3X8 1

* 29 994-301 SPINDLE (A) 1

* 29 994-302 SPINDLE (B) 1 FOR USA, CAN

* 30 937-817Z WHEEL WASHER 1

* 30 319-373 WHEEL WASHER 1 FOR USA, CAN

31 328-743 COVER (B) 1

32 308-386

MACHINE SCREW (W/SP. WASHER) M5X16 (BLACK) 2

33 301-949 SET PLATE 1

34 328-741 DUST COLLECTOR COVER (A) 1

35 942-808 BOLT (SQUARE) M6X20 1

36 328-809 SLIDE GUIDE (A) 1

* 37 994-324 WHEEL NUT M14 1

* 37 937-923P WHEEL NUT 5/8"-11 UNC 1 FOR USA, CAN

38 328-742 COVER (A) 1

39 324-865 DUST CAP 1

40 328-841 SLEEVE 1

41 314-622 WING NUT M6 1

42 949-785 ROLL PIN D6X16 (10 PCS.) 1

43 328-922 HITACHI PLATE 1

FOR DUST COLLECTION ADAPTER ASS'Y

44 314-428 SLIDE KNOB 1

45 325-050 HOUSING 1

46 999-088 CARBON BRUSH (1 PAIR) 2

- 2 - 12 - 07

*ALTERNATIVE PARTS

ITEM

NO.

USED

CODE NO.

PART

CM 5SB

DESCRIPTION REMARKS

47 317-810 BRUSH HOLDER 2

48 957-754 RUBBER RING 1

49 308-536 SPRING 2

50 325-051 SLIDE BAR 1

* 51 328-808 PUSHING BUTTON SWITCH 1

* 51 319-319 PUSHING BUTTON SWITCH 1 FOR GBR (110V), USA, CAN

* 52 317-491 NOISE SUPPRESSOR 1 FOR GBR (110V)

53 325-054 SWITCH HOLDER 1

54 953-327 CORD ARMOR D8.8 1

55 325-052 TAIL COVER 1

56 328-842 HITACHI PLATE 1

57 301-815 TAPPING SCREW (W/FLANGE) D4X45 2

* 58 319-320 FASTON TERMINAL 2 FOR GBR (110V)

* 59 314-854 EARTH TERMINAL 1 FOR GBR (110V)

60 980-063 TERMINAL 2 FOR CORD

61 984-750 TAPPING SCREW (W/FLANGE) D4X16 2

62 937-631 CORD CLIP 1

63 NAME PLATE 1

* 64 500-234Z CORD 1 (CORD ARMOR D8.8)

* 64 500-237Z CORD 1

(CORD ARMOR D8.8) FOR GBR (110V)

* 64 500-435Z CORD 1 (CORD ARMOR D8.8) FOR GBR (230V)

* 64 500-240Z CORD 1 (CORD ARMOR D8.8) FOR USA, CAN

65 328-740 DUST COLLECTION ADAPTER ASS'Y 1 INCLUD. 31-36, 38-43, 66

66 329-497 KNOB BOLT M5 1

12 - 07 - 3 -

*ALTERNATIVE PARTS

NO.

USED

CODE NO.

ITEM

NO.

STANDARD ACCESSORIE

CM 5SB

DESCRIPTION REMARKS

501 320-994 ADAPTER 1

502 937-913Z WRENCH 1

503 994-322 SIDE HANDLE 1

504 328-845 CASE (B) 1

OPTIONAL ACCESSORIE

DESCRIPTION REMARKS

601 310-338 SUPER WASHER 1

* 602 DIAMOND WHEEL 125MMXD36-D22.2 HOLE 1 EXCEPT FOR USA, CAN, GBR

- 4 - Printed in Japan 12 - 07

(071212N)

*ALTERNATIVE PARTS

NO.

USED

NO.

USED

CODE NO.

ITEM

NO.

ITEM

NO.

PART

CM 9SR

DESCRIPTION REMARKS

1 985-597 BOLT M14 2

2 322-141 PIPE HANDLE 1

3 306-888 PUSHING BUTTON 1

4 320-219 SPRING 1

5 320-218 O-RING 1

6 306-890 LOCK PIN 1

7 939-542

RETAINING RING FOR D12 SHAFT (10 PCS.) 1

8 320-224 GEAR 1

9 949-236 MACHINE SCREW M5X10 (10 PCS.) 2

10 320-229 BEARING COVER (B) 1

11 630-2VV BALL BEARING 6302VVCMPS2L 1

12 990-852 FELT PACKING (B) 1

13 320-234 SPINDLE 1

14 320-228 SEAL PLATE 1

15 320-227 PACKING GLAND 1

16 994-192

HEX. SOCKET HD. BOLT (W/FLANGE) M5X16 4

17 320-223 GEAR AND PINION ASS'Y 1 INCLUD. 8, 29

18 994-208 RUBBER RING (B) 1

19 320-220 BEARING COVER (A) 1

* 20 360-762C ARMATURE 110V 1

* 20 360-762E ARMATURE 220V-240V 1

21 320-215 FAN GUIDE 1

22 961-501 HEX. HD. TAPPING SCREW D5X60 2

* 23 340-664C STATOR ASS'Y 110V 1

* 23A 340-664H STATOR 220V-230V 1

24 958-032 BRUSH TERMINAL 2

25 984-509

SEAL LOCK HEX. SOCKET HD. BOLT M5X14 2

26 323-209

TAPPING SCREW (W/FLANGE) D5X35 (BLACK) 4

27 320-217 GEAR COVER ASS'Y 1 INCLUD. 3-6

28 320-226 SPECIAL NUT M10 1

29 320-225 PINION 1

30 320-221 SEAL WASHER 1

31 320-222 FELT PACKING 1

32 630-1VV BALL BEARING 6301VVCMPS2L 1

33 328-754 HOSE BAND 1

34 328-748 DUST DUCT 1

35 328-752 COVER (B) 1

36 HITACHI LABEL (B) 1

37 997-467 KNOB NUT 2

38 328-758 ADAPTER 1

39 328-761 RING 1

40 305-720 TAPPING SCREW (W/FLANGE) D4X12 2

41 324-877 BOLT (SQUARE) M6X57 2

42 328-759 ADAPTER (A) 1

43 328-760 ADAPTER (B) 1

44 324-865 DUST CAP 1

46 885-414 HOLDER SLEEVE (B) 1

47 328-841 SLEEVE 1

48 314-622 WING NUT M6 2

49 311-492 LABEL 1

- 2 - 12 - 07

*ALTERNATIVE PARTS

ITEM

NO.

USED

CODE NO.

PART

CM 9SR

DESCRIPTION REMARKS

50 673-489 RETAINING RING (E-TYPE) FOR D5 SHAFT 1

51 321-546 SET PIN 1

52 321-545 LEVER 1

53 306-887 BOLT M8X22 1

54 949-457 SPRING WASHER M8 (10 PCS.) 1

55 321-544 SET PIECE 1

56 328-745 WHEEL GUARD ASS'Y 1 INCLUD. 49-55

57 328-843 BOLT (A) 1

58 937-907Z WHEEL WASHER (A) 1

59 937-909Z WHEEL NUT M14X2 1

60 328-749 COVER (A) 1

61 328-750 HOLDER 1

62 314-429 SPRING 1

63 328-751 POCKET GUIDE 1

64 974-577

RETAINING RING (E-TYPE) FOR D7 SHAFT 8

65 328-755 ROLLER 4

66 328-756 ROLLER SHAFT 2

67 328-757 BOLT (SQUARE) M5 2

68 328-747 BASE 1

69 320-216 DUST SEAL 1

70 600-0VV BALL BEARING 6000VVCMPS2L 1

71 321-536 BEARING BUSHING 1

72 325-640 HOUSING ASS'Y 1 INCLUD. 71, 79, 80

73 NAME PLATE 1

74 325-642 HANDLE (A) 1

75 305-812

TAPPING SCREW (W/FLANGE) D4X16 (BLACK) 4

76 HITACHI LABEL 1

77 940-540 BRUSH CAP 2

* 78 999-044 CARBON BRUSH (1 PAIR) 1

* 78 999-074

CARBON BRUSH (AUTO STOP TYPE) (1 PAIR) 1

* 78 999-044 CARBON BRUSH (1 PAIR) 2 FOR GBR

79 980-487 BRUSH HOLDER 2

80 938-477 HEX. SOCKET SET SCREW M5X8 1

* 81 320-239

SWITCH (2P PILLAR TYPE) W/SAFETY LOCK 1

* 81 320-238

SWITCH (2P PILLAR TYPE) W/SAFETY LOCK 1 FOR FRA, HOL, BEL, GBR, NOR, DEN

82 960-266 CORD CLIP 1

83 984-750 TAPPING SCREW (W/FLANGE) D4X16 2

84 325-641 HANDLE (B) 1

85 981-373 TUBE (D) 2 FOR CORD

86 940-778 CORD ARMOR D10.7 1

* 87 500-247Z CORD 1 (CORD ARMOR D10.7)

* 87 321-539 CORD 1

(CORD ARMOR D10.7) FOR GBR (110V)

* 87 500-450Z CORD 1 (CORD ARMOR D10.7) FOR GBR (230V)

88 328-744 DUST COVER ASS'Y 1 INCLUD. 33-44, 46-48, 56, 57, 60-68, 93

93 944-950 U-NUT (B) M8 1

12 - 07 - 3 -

*ALTERNATIVE PARTS

NO.

USED

CODE NO.

ITEM

NO.

STANDARD ACCESSORIE

CM 9SR

DESCRIPTION REMARKS

501 320-994 ADAPTER 1

502 937-913Z WRENCH 1

503 328-844 CASE (A) 1

OPTIONAL ACCESSORIE

DESCRIPTION REMARKS

601 310-337 SUPER WASHER 1

* 602 DIAMOND WHEEL 230MMXD40-D22.2 HOLE 1 EXCEPT FOR GBR

- 4 - Printed in Japan 12 - 07

(071212N)

*ALTERNATIVE PARTS

NO.

USED

NO.

USED

CODE NO.

ITEM

NO.

ITEM

NO.

Page is loading ...

Hitachi CM 5SB, CM 9SR, CM 9UBY, CM5SB Technical Data And Service Manual

Related papers

Other documents