Arthur Jackson CTC MIKE 2.0 Setup And Operation Manual

Brand: Arthur Jackson CTC

Model: MIKE 2.0

Type: Setup And Operation Manual

Arthur Jackson CTC MIKE 2.0

The Arthur Jackson CTC MIKE 2.0 is a versatile training tool that can be used to improve CPR skills. The device is easy to assemble and operate, and it comes with a variety of features that make it ideal for use in both individual and group training sessions.

Features:

Realistic chest compression feedback: The MIKE 2.0 provides real-time feedback on the depth and rate of chest compressions, helping users to improve their technique.
Pressure sensor: The device's pressure sensor measures the force applied to the chest during compressions, providing users with feedback on the amount of pressure they are using.

Arthur Jackson CTC MIKE 2.0

Features:

Realistic chest compression feedback: The MIKE 2.0 provides real-time feedback on the depth and rate of chest compressions, helping users to improve their technique.
Pressure sensor: The device's pressure sensor measures the force applied to the chest during compressions, providing users with feedback on the amount of pressure they are using.

MIKE 2.0 TRAINING STATION

SETUP AND OPERATIONS MANUAL

Assembly of the Mike 2.0 training station

The mike 2.0 training station is easy to assemble and operate. Assembly instructions are as

follows;

1.0) Check contents of shipping container. Each container should contain the following

pieces;

A.) Head and Body units

B.) Pressure Sensor

C.) Face mask and safety valves

D.) Samsung Galaxy A Tablet

E.) One (1) Bench Pad

F.) Training Manual

H.) Carry bag

2.0) Assemble the base unite by connecting the loop and hook (Velcro) strips together. (The

units can be separated for storage in the carry bag.) Base unit has chest image plate mounted

on it. The chest image can be a skeleton or human chest.

3.0) Mount the Samsung tablet on the lower half of the base unit as shown.

4.0) Mount sensor on the chest plate mounted on the base unit as shown.

5.0) Insert the plug from the sensor (It is a simple audio plug in) into the audio jack on the inter-

face unit as shown.

6.0) Place face mask on the head unit with connected interface under the mask as shown.

7.0) Completed unit should look like the picture below.

Charging the devices

The Mike 2.0 training station is now assembled, and ready to use. You should be sure the interface

and tablet are fully charged. The tablet is supplied with a connector on the unit to allow charging by

plugging into any AC receptacle. (Consult the Samsung documents for complete directions.)

The interface unit comes with a mini USB cable to connect the device to a USB device or comput-

er for charging.

1. To charge the battery, connect a micro USB cable to the connector on

the interface. Plug the USB cable into a USB charger or computer port.

2. The LED will blink red every 10 seconds while charging.

Charging times for these devices can vary. Generally, full charging can be completed in two (2) to

three (3) hours.

Turning Devices off and on

Tablet power : Consult the Samsung material supplied with the tablet.

Turning on the interface: There is a single white button on the interface. Press the button and re-

lease once. Red and green leds will flash indicating the device is charged and active.

Turning off the interface: To disconnect, press and hold the top button on the sensor for 5 seconds.

When the LED indicator turns red and stops blinking, release the button. The Led should turn off

and stay off. The device is now off.

Operating the Mike 2.0 Training Station

Once assembled, the Mike 2.0 station is ready for operation. When the purchase of the station was

made, you received a down load of the APP, CPR Mirror, to your Android device, or the CPR Mir-

ror APP was pre- loaded into the Samsung Tablet upon purchase. Once your android device is ac-

tivated (turned on), the following icon will be on your desk top:

Tap the icon, then the following screen will appear;

Followed by this screen;

I f your interface unit is on, the screen will change to the following;

Finally you will get the final screen;

Your APP is up and The icons at the top

operating . The top control:

Graph is air pressure 1.0) frequency of reading

And the bottom is the

Sensor pressure in pounds. 2.0) Units of measure

If you sensor and interface

Are connected the graphs 3.0) type of sensors

Will display weight on the displayed

Sensor and air pressure

Through the face mask.

To record, tap record to start

And stop to stop

The interface will pair with your android device, and is now ready to use.

ATTENTION BE SURE NOT TO OPERATE OTHER BULE TOOTH DEVICES NEAR THE INTER-

FACE WHEN IT IS BEING PAIRED WITH YOUR ANDROID DEVICE. This will cause the interface

to not pair with your android device.

Arthur Jackson CTC MIKE 2.0 Setup And Operation Manual

Brand: Arthur Jackson CTC

Model: MIKE 2.0

Type: Setup And Operation Manual

Arthur Jackson CTC MIKE 2.0

Features:

Realistic chest compression feedback: The MIKE 2.0 provides real-time feedback on the depth and rate of chest compressions, helping users to improve their technique.
Pressure sensor: The device's pressure sensor measures the force applied to the chest during compressions, providing users with feedback on the amount of pressure they are using.

Download PDF

report

Arthur Jackson CTC MIKE 2.0 Setup And Operation Manual

Arthur Jackson CTC MIKE 2.0 Setup And Operation Manual

Other documents