L26A6A-A1L26A6A-A1
LCD COLOR TELEVISION
OPERATING
INSTRUCTIONS
◆Wide view-angle display, high contrast
◆NICAM
◆AAA function
◆HDMI input
01
0090508356
1
CONTENTS
Warning and caution...........................................................................................2
Buttons and interface position............................................................................5
Front control panel.........................................................................................5
Back interface.................................................................................................5
Preparation for remote controller.......................................................................6
Remote controller panel.....................................................................................7
Base installation instructions...............................................................................8
Sound box installation instructions.....................................................................9
Basic operation................................................................................................10
Power on/off TV............................................................................................10
TV program selection and volume adjustment..............................................10
Recall.............................................................................................................10
Mute function................................................................................................10
OSD language selection................................................................................10
Screen display...................................................................................................11
TV program setting..........................................................................................12
Auto search...................................................................................................12
Manual search...............................................................................................12
Fine tune.......................................................................................................13
Skip...............................................................................................................13
Exchange.......................................................................................................14
Image control....................................................................................................14
Set your favourite picture mode....................................................................14
Noise reduce..................................................................................................14
Picture mode /sound mode selection.............................................................15
Sound control...................................................................................................15
Sound effect control......................................................................................15
System setting function....................................................................................15
OSD background setting...............................................................................15
Signal source setting......................................................................................16
Screen display picture zoom setting..............................................................16
Other setting function.......................................................................................16
Sleep timer setting.........................................................................................16
PIP setting......................................................................................................17
Sound source setting......................................................................................17
Color temperature..........................................................................................18
Digital filter setting........................................................................................18
AAA setting...................................................................................................18
HDMI.............................................................................................................19
External audio and video equipment connection..............................................20
Using your TV as a computer display..............................................................21
Specifications...................................................................................................22
Trouble shooting guide.......................................................................................23
2
WARNING AND CAUTION
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
IF ANY PROBLEM, REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
THERE IS A LIGHTENING ARROW SYMBOL IN THE TRIANGLE:
THIS SYMBOL INDICATES HIGH VOLTAGE IS PRESENT INSIDE.
IT IS DANGEROUS TO MAKE ANY KIND OF CONTACT WITH ANY
INSIDE PART OF THIS PRODUCT.
THERE IS A EXCALMATORY MARK IN THE TRIANGLE: THIS
SYMBOL ALERTS YOU THAT IMPORTANT LITERATURE
CONCERNING. OPERATION AND MAINTENANCE HAS BEEN
INCLUDED WITH THIS PRODUCT.
CAUTION
DO NOT OPENDO NOT OPEN
RISK OF ELECTRIC SHOCK RISK OF ELECTRIC SHOCK
!!
!!
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK AND FIRE,
DO NOT PUT THE TV SET IN THE DRIZZLING FOG PLACE.
DO NOT USE ANY HARD OBJECT WHICH MAY SCRATCH
OR DAMAGE THE LCD SCREEN TO CLEAN OR KNOCK
THE LCD SCREEN.
NOTE:
FORBID CHANGING THE PRODUCT YOURSELF IN ANY
WAY WITH UNAUTHORIZED SITUATION.
BUTTONS AND INTERFACE POSITION
5
CH +
CH -
VO L +
VO L -
TV / A V
ME N U
Front control panel
Power switch
Program up/down button
Volume up/down button
TV/AV switch button
Menu button
Power indicator
Remote sensor
Back interface
1. Power input socket
2. Antenna input
3. Video input 2
4. Video input 1
5. S-VIDEO input
6. HDTV or S-VIDEO audio input
7. Video output
8. HDTV input
9. VGA audio input interface
10. VGA input
11.Power switch
12.HDMI input
PREPARATION FOR REMOTE CONTROLLER
3
2
1
++
Remote controller installation
1. According to the below figure display, place the remote controller with face down,
then open the cover of battery apartment.
2. As the below figure display, mount two AA batteries. (The cathode and anode of
battery must match with the mark).
3.Close the cover of battery apartment.
Cautions for using remote controller
Confirm there is no object between the
remote controller and the remote sensor
of TV set.
The sunshine or other strong light will
interfere the signal sent by the remote
controller. In this situation turn the TV
set to the other direction.
Do not put the remote controller in the
heat or damp place, or the strong strike
will result in operating invalid.
Please use two AA 1.5V batteries.
Do not mix battery types.
Mount the battery as the correct
polarities.
Do not use the rechargeable batteries.
6
1 24
57
910
8
6
3
1
AC
11
HDMI
12
BASE INSTALLATION INSTRUCTIONS
8
1. LCD TV base accessory
LCD TV
TV base
M4*8 screw
Name
Qty.
LCD TV
LCD TV base
M4*8 screw (black)
2. LCD TV base installation procedure
(1) Take out the LCD TV and TV base
from packing box, lie the LCD TV
on the clean blanket with face down
in order to prevent the hard object
from scratching the LCD screen, as
figure (1).
(2)Take nine M4*8 black screws from the
accessory bag, refer to figure (2), use
screw to tighten the base on the back
cover of TV set.
(3)Finish installing the LCD TV base,
figure (3).
Figure(1)
Figure(1)
Figure(3)
REMOTE CONTROLLER PANEL
1
2
3
4
7
8
9
11
12
13
14
15
16
17
18
20
21
23
22
24
10
25
19
5
6
11
Power button
Mute button
TV/AV switch button
Display button
Dynamic AAA HDTV on/off button
PIP function on/off button
PIP main/sub picture switch button
PIP sound selection button
One digit selection button
Program recall button
Child lock button
Picture mode selection button
Sound mode selection button
Program up/down button, direction
selection button
Volume up/down button, direction
selection button
Menu call/selection button
Color system selection button
Sound system selection button
Program scan button
Picture still button
This function is not available
Picture size selection button
Sleep timer button
This function is not available
This function is not available
Nicam button
This function is not available
Buttons and Descriptions
26
7
27
5
8
9
10
1 2 3
4
5
6
7
8 9
0
←
↑
↓
→
=
←
HYF -35 R
1
3
7
2
6
4
PIP
AAA
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
MUTE
TV/AV
SOUND
POWER
MAIN/SUB
DISPLAY
CHILD LOCK
P.STD
RECALL
S.STD
CH+
CH-
VOL-
VOL+
MENU
C.SYS
S.SYS
STILL SCAN
BACKZOOM
SLEEP
SIZE
27
26
I-II
SOUND BOX INSTALLATION INSTRUCTIONS
9
1. Place the LCD TV with installed
base well, take out the sound box
from packing box, take out two
connecting blocks of sound box,
eight screws and two connecting
wires of sound box from accessory
bag, as figure (1).
2. Refer to figure (2) display (LCD
back view figure), fix the two
connecting blocks of sound box
on the back cover of LCD TV by
using four screws.
3. Refer to figure (3) display (LCD
back view figure), fix the
connecting blocks of sound box
and back cover of sound box by
using the remaining four screws.
4. Refer to figure (3), clip the two
connecting wires of sound box as
figure display into the up and
down four connecting wire cards
separately, the sound box is
finished installing.
BASIC OPERATION
10
1. If the TV set is in standby status, pressing power
switch on the remote controller or TV set can
cancel the standby status, then enter the power on
status.
2. Pressing power switch on the remote controller or
the TV set again, the TV set will enter standby
status.
Standby set: first connect the power supply wire,
then turn the power switch on the back of TV set on.
TV PROGRAM SELECTION AND VOLUME
ADJUSTMENT
You can use CH+/- button or direct-digit choosing
button to select the TV channel number.
Press VOL+/- button to adjust the volume.
RECALL
Pressing RECALL button can switch the channel to the
last channel you watched.
MUTE FUNCTION
1. Press MUTE button to shut off the TV sound, the
screen displays mute mark.
2. Press MUTE button again or VOL+ button to turn
on the TV sound.
OSD LANGUAGE SELECTION
Select the LANGUAGE item in the menu
1. Press MENU button to select OSD setting menu.
2. Press CH+/- button to select LANGUAGE item.
3. Press VOL+/- button to select the language you need.
OSD
MOVE SELECT MENU EXIT
MUTE
TV/AV
SOUND
POWER
MAIN/SUB
PIP
AAA
DISPLAY
POWER ON/OFF TV
LANGUAGE ENGLISH
H-POSITION
V-POSITION
DURATION
TRANSPARENCY
Connecting block
of sound box
Sound box
Figure (1)
Two screws
Two screws
Figure (2)
Two screws
Two screws
Connecting wires
of sound box
Figure (3)
SCREEN DISPLAY
11
For your convenient operation and in order to know the TV set, we offer the below
menus.
Picture setting menu
Sound setting menu
Menu setting menu
Function setting menu
Source setting menu
PICTURE MODE NATURAL
CONTRAST
BRIGHTNESS
SATURATION
TINT
SHARPNESS
NOISE REDUCE
SIZE MODE
STRONG
FULL
PICTURE
MOVE SELECT MENU EXIT
PICTURE SOURCE TV
PIP MODE OFF
SUB PICTURE VGA
COLOR SYSTEM AUTO
SOUND SYSTEM
AUTO SEARCH
MANUAL SEARCH
I
SOURCE
MOVE SELECT MENU EXIT
MOVE SELECT MENU EXIT
SOUND
SOUND SOURCE MAIN
SOUND MODE NEWS
BALANCE
EQUALIZER
LANGUAGE ENGLISH
H-POSITION
V-POSITION
DURATION
TRANSPARENCY
OSD
MOVE SELECT MENU EXIT
CLOCK 00:12
TIME ON --:--
TIME OFF --:--
SLEEP TIMER OFF
COLOR TEMP USER
D FILTER
AAA ON
MOVE SELECT MENU EXIT
FUNCTION
Operation instructions
the real display may be different from the above menus, if you need adjust, please do as
follows:
1.Press MENU button to open the menu, use CH+/- button to select every menu
separately, use VOL+/- button to enter.
2.Press CH+/- button to select the item needs adjust.
3.Press VOL+/- button to adjust the selected item, or enter the next menu.
4.Press MENU button to return the last menu or exit the screen menu display.
Note: “press MENU button to select the menu ”operation in the user’s manual, please
refer to this operation instructions.
PICTURE SOURCE TV
PIP MODE OFF
SUB PICTURE VGA
COLOR SYSTEM AUTO
SOUND SYSTEM
AUTO SEARCH
MANUAL SEARCH
I
SOURCE
MOVE SELECT MENU EXIT
AUTO SEARCH
12
Using AUTO SEARCH can search all receiving
programs. We recommend using auto search to
search the program when you use this TV set for
the first time, before auto search, please confirm
the sound system is I.
1.Press MENU button to select source menu.
2.Press CH+/- button to select AUTO SEARCH.
3.Press VOL+/- button to start searching, press MENU
button to finish auto search.
Note: The order of the auto search is due to the
frequency of the program, generally speaking,
it is used only at the first time you search the
program, and once the order of the program has
been confirmed, you don’t have to use this
function, otherwise the order of the program
will be changed.
MANUAL SEARCH
Manual search can search and order the program freely.
1. Press MENU button to select the source menu.
2. Press CH+/- button to select MANUAL SEARCH,
press VOL+/- button to enter the next menu.
3. Press CH+/- button to select MANUAL SEARCH.
4. Press VOL+/- button to start searching, pressing
VOL+ button is used to search the higher frequency
channel, pressing VOL- button is used to search the
lower frequency channel, when you have searched
a program, the searching will stop automatically.
You can press VOL+/- button to go on searching or
press MENU button to exit.
Note: During searching, it may appear black screen
because of change of signal, it is normal, it will
recover after finishing searching.
CURRENT CHANNEL 10
SKIP OFF
TARGET CHANNEL 10
EXCHANGE
AFC OFF
FINE TUNE
SEARCH NEXT 471.2MHZ
SOURCE
MOVE SELECT MENU EXIT
TV PROGRAM SETTING
TV PROGRAM SETTING
13
CURRENT CHANNEL 10
SKIP OFF
TARGET CHANNEL 10
EXCHANGE
AFC OFF
FINE TUNE
SEARCH NEXT 471.2MHZ
SOURCE
MOVE SELECT MENU EXIT
CURRENT CHANNEL 10
SKIP OFF
TARGET CHANNEL 10
EXCHANGE
AFC OFF
FINE TUNE
SEARCH NEXT 471.2MHZ
SOURCE
MOVE SELECT MENU EXIT
CURRENT CHANNEL 10
SKIP OFF
TARGET CHANNEL 10
EXCHANGE
AFC OFF
FINE TUNE
SEARCH NEXT 471.2MHZ
SOURCE
MOVE SELECT MENU EXIT
When you can’t get a satisfactory picture effect,
you can fine tune to obtain.
1. Press MENU button to select source menu.
2. Press CH+/- button to select MANUAL
SEARCH, press VOL+/- button to enter the next
menu.
3. Press CH+/- button to select FINE TUNE.
4. Press VOL+/- button to start fine tune until you
obtain the best picture and sound, then loose
the button, press MENU button to exit.
SKIP
1. Select the program number you need skip.
2. Press MENU button to select source menu.
3. Press CH+/- button to select the MANUAL
SEARCH, press VOL+/- button to enter the
next menu.
4. Press CH+/- button to select SKIP, press
VOL+/- button to select ON.
5. Press MENU button to shut off the menu.
When you use CH+/- button to select channel,
this channel number will be skipped. But you
can still use one direct-digit choosing button to
select the skipped channel number.
Note: How to recover the skipped channel number
1. Press direct-digit choosing button to select the
channel number that needs recover.
2. Press MENU button to enter source menu.
3. Press CH+/- button to select SKIP, press VOL+/-
button to select OFF.
FINE TUNE
14
CURRENT CHANNEL 15
SKIP OFF
TARGET CHANNEL 28
EXCHANGE
AFC OFF
FINE TUNE
SEARCH NEXT 471.2MHZ
SOURCE
MOVE SELECT MENU EXIT
1. Press MENU button to select source menu.
2. Press CH+/- button to select MANUAL
SEARCH, press VOL+/- button to enter the next
menu.
3. Press CH+/- button to select TARGET CHANNEL,
press VOL+/- button to select the channel you need
exchange.
4. Press CH+/- button to select EXCHANGE, press
VOL+/- button to exchange, as figure, exchange
the current channel number 15 to channel number
28.
5. Press MENU button to save and exit.
Note: Please shut off the connected but not used signal
source in order not to affect normal watching.
SET YOUR FAVOURITE PICTURE MODE
PICTURE MODE NATURAL
CONTRAST
BRIGHTNESS
SATURATION
TINT
SHARPNESS
NOISE REDUCE
SIZE MODE
STRONG
FULL
PICTURE
MOVE SELECT MENU EXIT
PICTURE MODE NATURAL
CONTRAST
BRIGHTNESS
SATURATION
TINT
SHARPNESS
NOISE REDUCE
SIZE MODE
STRONG
FULL
PICTURE
MOVE SELECT MENU EXIT
1. Press MENU button to select picture menu.
2. Press CH+/- button to select the item that needs
adjust.
3. Press VOL+/- button to adjust the selected item,
the detailed adjustment is as following table.
The table of picture item adjustment effect
*
Items
VOL- VOL+
Contrast
Brightness
Saturation
Tint
Sharpness
Weak
Strong
Dark
Bright
Light
Thick
Green
Red
Soft Sharp
Note: TINT is only valid in N system.
NOISE REDUCE
Noise reduce can decrease the noise of picture
1. Press MENU button to select the picture menu.
2. Press CH+/- button to select the NOISE REDUCE.
3. Press VOL+/- button to select OFF, WEAK or
STRONG as your require.
EXCHANGE
TV PROGRAM SETTING
IMAGE CONTROL
SET YOUR FAVOURITE PICTURE MODE
MOVE SELECT MENU EXIT
SOUND
SOUND SOURCE MAIN
SOUND MODE NEWS
BALANCE
EQUALIZER
PICTURE MODE/SOUND MODE SELECTION
15
0
移动 选择 菜 单 退 出
0
TRANSPARENCY
63
50
75 100 300 1K 3K 5K 10K 15K
声 音
LANGUAGE ENGLISH
H-POSITION
V-POSITION
DURATION
TRANSPARENCY
OSD
MOVE SELECT MENU EXIT
MOVE
SELECT MENU EXIT
MOVE
SELECT MENU EXIT
Press P.STD button on the remote controller
continually, the following four picture modes
can be selected in turn.
NATURAL: common mode.
SOFT: the image effect is soft.
USER: set the image effect you like.
BRIGHT: suitable for sport image.
NATURAL
BRIGHT PERSONAL SOFT
Press S.STD button on the remote controller
continually, the following four sound modes
can be selected in turn.
You can also enter picture and sound menu to adjust.
NORMAL
MUSIC PERSONAL
NEWS
You can select your favourite sound modes, and adjust
the BALANCE and EQUALIZER of sound.
1. Press MENU button to select sound menu.
2. Press CH+/- button to select the sound item you
need set.
3. Press VOL+/- button to adjust the selected item.
BALANCE: Press VOL+/- button to enter adjustment,
use VOL+/- button to adjust the balance of left and
right sound.
EQUALIZER: Press VOL+/- button to enter EQUALIZER
set menu, use VOL+/- button to select every different
frequency, use CH+/- button to adjust.
The higher of the transparency set value is,
the higher of the OSD transparency is, whereas,
the transparency is lower.
1. Press MENU button to select OSD setting menu.
2. Press CH+/- button to select the OSD background
item.
3. Press VOL+/- button to set the transparency value.
Note: Sound source only can be adjusted in PIP mode.
SYSTEM SETTING FUNCTION
CHILD LOCK
P.STD
CHILD LOCK
P.STD
RECALL
S.STD
RECALL
S.STD
IMAGE CONTROL
SOUND CONTROL
OSD BACKGROUND SETTING
SOUND EFFECT CONTROL
SYSTEM SETTING FUNCTION
16
PICTURE SOURCE TV
PIP MODE OFF
SUB PICTURE VGA
COLOR SYSTEM AUTO
SOUND SYSTEM
AUTO SEARCH
MANUAL SEARCH
I
SOURCE
MOVE SELECT MENU EXIT
PICTURE MODE NATURAL
CONTRAST
BRIGHTNESS
SATURATION
TINT
SHARPNESS
NOISE REDUCE
SIZE MODE
STRONG
FULL
PICTURE
MOVE SELECT MENU EXIT
CLOCK 00:12
TIME ON --:--
TIME OFF --:--
SLEEP TIMER OFF
COLOR TEMP USER
D FILTER
AAA ON
MOVE SELECT MENU EXIT
FUNCTION
There is different signal source mode in this TV set,
you can select according to your require: TV,
VIDEO1, VIDEO2, S-VIDEO, HDTV, VGA, HDMI.
1. Press MENU button to select source menu.
2. Press CH+/- button to MAIN.
3. Press VOL+/- button to select the signal source
mode you need.
4. You can press TV/AV button on the remote
controller to select directly.
SCREEN DISPLAY PICTURE ZOOM SETTING
There is different screen display picture zoom,
you can select according to your require: FULL,
ZOOM1, ZOOM2, NORMAL.
1.Press MENU button to select picture menu.
2.Press CH+/- button to select SIZE MODE.
3.Press VOL+/- button to select the zoom you need.
4.You can press ZOOM button on the remote
controller to switch.
OTHER SETTING FUNCTION
After you set the sleep timer, the TV set will count
from the setting time, when the count time is coming,
the TV set will turn off automatically.
Press SLEEP button to enter off time set, you can
select the certain time: OFF, 15Min, 30Min, 60Min...
240Min, after setting, the TV set will start count.
Note: if you want to see the off time you set, press
SLEEP button. If you want to cancel the sleep time
set, follow the above procedures, set the time OFF.
SIGNAL SOURCE SETTING
SLEEP TIMER SETTING
PIP SETTING
17
This TV set support PIP function, it can display
picture of two sources at the same time.
1.Press MENU button to select source menu.
2.Select PIP mode, use VOL+/- button to select
P1S1, P1S2, P2S1, P2S2, P3S1, P3S2, P4S1or
P4S2 mode, open PIP function.
3.Select MAIN PICTURE SOURCE, use VOL+/-
button to change the input source of main picture,
such as TV, VIDEO1, VIDEO2 and so on.
4.Select sub picture source, use VOL+/- button to
change the input source of sub picture, such as
VGA, HDTV, HDMI and so on.
Note:
1. After switching the main picture source, it will
shut off the PIP function, if need, you can open
this function again.
2. The following two suit
can use PIP function,
the same suit source
can not use PIP
function, source1
and source2 can switch.
3.You can press PIP button on the remote controller
to turn on or turn off the PIP function.
4.You can press MAIN/SUB button on the remote
controller to switch the main picture and sub picture.
PICTURE SOURCE TV
PIP MODE OFF
SUB PICTURE VGA
COLOR SYSTEM AUTO
SOUND SYSTEM
AUTO SEARCH
MANUAL SEARCH
I
SOURCE
MOVE SELECT MENU EXIT
SOURCE1
SOURCE2
TV, VIDEO1, VIDEO2, S-VIDEO
VGA, HDTV, HDMI
SOUND SOURCE SETTING
After the PIP function is opened, this item is activated,
you can select the main picture sound or sub picture
sound of current broadcasting sound.
1.Press MENU button to select sound menu.
2.Press CH+/- button to select SOUND SOURCE.
3.Press VOL+/- button to change the current sound to
main picture sound or sub picture sound.
Note:
1.You can also press SOUND button on the remote
controller to switch the main picture sound or sub
picture sound.
2.After switching the sound to sub picture sound, you
can switch the source in sub picture.
OTHER SETTING FUNCTION
MOVE SELECT MENU EXIT
SOUND
SOUND SOURCE MAIN
SOUND MODE NEWS
BALANCE
EQUALIZER
18
CLOCK 00:12
TIME ON --:--
TIME OFF --:--
SLEEP TIMER OFF
COLOR TEMP USER
D FILTER
AAA ON
MOVE SELECT MENU EXIT
FUNCTION
CLOCK 00:12
TIME ON --:--
TIME OFF --:--
SLEEP TIMER OFF
COLOR TEMP USER
D FILTER
AAA ON
MOVE SELECT MENU EXIT
FUNCTION
CLOCK 00:12
TIME ON --:--
TIME OFF --:--
SLEEP TIMER OFF
COLOR TEMP USER
D FILTER
AAA ON
MOVE SELECT MENU EXIT
FUNCTION
1.Press MENU button to select function menu.
2.Press CH+/- button to select COLOR TEMP.
3.Press VOL+/- button to select DEFAULT→ 6500K→
→7300K→8500K→9300K→USER
Note: PERSONAL is the color temperature of picture
you set through D FILTER.
DIGITAL FILTER SETTING
Use D FILTER can adjust the color temperature
exactly.
1.Press MENU button to select function menu.
2.Press CH+/- button to select D FILTER.
3.Press VOL+/- button to select the COLOR TEMP,
use CH+/- button to adjust.
AAA SETTING
AAA function can improve the quality of picture and
make the picture best.
1.Press MENU button to select function menu.
2.Press CH+/- button to select AAA.
3.Press VOL+/- button to select DEMO, SPLIT or
OFF.
4.Press AAA button on the remote controller to start
and select AAA mode.
DEMO: Use one moved sub picture in the picture to
start AAA function.
SPLIT: Separate the picture from left and right, start
AAA function in left picture.
Note: It can not use the DEMO, SPLIT function with
no signal and in PIP mode.
COLOR TEMPERATURE
OTHER SETTING FUNCTION
19
- HDMI . The HDMI logo and High-Definition Multimedia Interface is a trademark
or registered trademark of HDMI Licensing.
-This TV can receive the High-Definition Multimedia Interface (HDMI).
-This TV supports HDCP (High-bandwidth Digital Contents Protection) Protocol for
720x480p, 1280x720p, and 1920x1080i resolution.
-When you connect this TV with a source device (DVD player, Set Top Box or PC)
supporting Auto HDMI function, the output resolution of the source device will be
automatically set to 1280x720p.
-If the source device does not support Auto HDMI, you need to set the output
resolution appropriately.
To get the best picture quality, adjust the DVD Player or Set Top Box’s output resolution
to 1280x720p, and the PC graphics card’s output resolution to 1024x768, 60Hz.
-If the source device has an HDMI output, no other audio connection is necessary
because HDMI-to-HDMI connecting includes both video and audio.
How To Connect
1. Connect the source device to HDMI port of this TV with an HDMI cable (not
supplied with this product).
2. No separated audio connection is necessary.
How To Use
-If the source device supports Auto HDMI function, the output resolution of the source
device will be automatically set to 1280x720p.
-If the source device does not support Auto HDMI, you need to set the output resolution
appropriately.
To get the best picture quality, adjust the output resolution of the source device to
1280x720p.
-Select HDMI input source by using TV/AV button.
How To Set
The method to set is similar to TV mode.
OTHER SETTING FUNCTION
TM
20
EXTERNAL AUDIO AND VIDEO EQUIPMENT CONNECTION
You can connect outside signal source VCR VCD
DVD PC equipment to the TV set.
Antenna Input
1.Connect the VCR radio frequency input to
the back radio frequency input of the LCD.
2. Connect the antenna to VCR antenna input.
3. Press TV/AV button to select TV mode.
4. Press PLAY button in VCR to start watching.
AV input
1.Connect audio video output port in VCD to
AUDIO IN and VIDEO IN port in TV set.
2. Press TV/AV button to select composite
VIDEO mode.
3. Press PLAY button in VCD to start watching.
S-VIDEO input
If you use S terminal as signal input source,
the image quality will be better than video(AV).
1.Connect S terminal output in DVD to S terminal
input in TV set.
2.Connect S terminal left/right audio output in DVD to
the relevant port in TV set.
3.Press TV/AV button repeatedly until the display
mode is S-VIDEO.
4.Press PLAY button in DVD to broadcast. At this time
the image programs in DVD will broadcast in TV set.
DTV input
1. Component terminal (Y/PbCb/PrCr) connect to the
component output of picture output device (such as
DVD, HDTV TUNER and so on ), the sound is input
from AUDIO IN:
2.Press TV/AV button to select HDTV mode.
3.Press PLAY button on the external device to start
watching.
HDMI input
1.Connect HDMI signal source output to the HDMI
input in this TV set.
2.Press TV/AV button to select HDMI mode.
3.Press PLAY button on the external device to start
watching.
AN T .
VCR
AU D IO I N
LL
RR
S- V ID E O
IN
VID EO IN
VCD
AU D IO I N
L
R
S- V ID E O
IN
VIDEO IN
DVD
DVD
LL
RR
AU D IO I N
Y Cb / P b C r/ P r
HDMI
DVD
USING YOUR TV AS A COMPUTER DISPLAY
21
VG A - A U D I O I N
VGA
VGA input
1. Connect the VGA output port in the computer to the VGA port in the TV set.
2. Connect the audio cable in computer to VGA AUDIO IN port in TV set.
3. Press TV/AV button to select VGA mode.
4. Turning on the computer, the screen image of the computer will display on the
TV set.
At this time, the TV set can use as a computer display.
Note:
1. If the temperature of the TV set is rather low, it is normal that there is
a little glitter when you turn it on .
2. There is a little red, green and blue spot, but it has no influence on
normal display.
3. In the standard range, It is normal if there is one bright dot or dark dot on the screen.
VGA
SVGA
XGA
640*480
800*600
1024*768
31.5KHz
37.9KHz
48.4KHz
60Hz
60Hz
60Hz
Mode
Resolution
Horizontal
Frequency
Vertical
Frequency
RESOLUTION:
Note: The above parameter is VESA standard.
SPECIFICATIONS
22
L26A6A-A1
70.0×20.6×61.9(included base）
The part specifications of this TV set provided here is only to give you reference.
Maybe there is a little difference from practice because of improving.
Model
Screen
Type
Viewable angle
Color system
Sound system
Video input
TV/VIDEO
PAL, NTSC (VIDEO)
DTV Y/Pb/Pr
Power
Power consumption
Dimension (W×H×D)(cm)
Environment conditions
Accessory
Composite: 480i/p, 576i, 720p,1080i,1080p
AC 150-240V 50/60Hz
CVBS, S-VHS, YPb/Pr, YCb/Cr, RGB,HDMI
DK, I, BG
Working temperature:
Working humidity:
Storage temperature:
Storage humidity:
+5℃～35℃
20%-80%
-10℃～45℃
5%-90%
User’s manual (×1)
Remote controller (×1)
Warranty card (×1)
Power cord (×1)
Sound box connecting wire (×2)
Sound box connecting block (×2)
Screw (×17)
The design and specifications are subject to change without notice.
A-si TFT active maxrix
176°(H)/176° (V)
Max.150W
TROUBLE SHOOTING GUIDE
23
Note:1.If the problem can not be fixed after you check above items. DO NOT attempt
to remove the back cover by yourself.
2.If the snapping sound from the cabinet of the TV set can be heard occasionally
because of temperature changing of environment, it is normal, you can use it
reassuringly.
BREAKDOWN PHENOMENON
PICTURE
SOUND
CHECKING
The direction and connection of the
antenna
Direction, station and connection
of the antenna
Interference from electric
appliance. Automobile、Motor,
Vehicle Fluorescence lamp etc.
Volume, Sound mute
The power plug isn't plugged in AC
outlet. The main power isn't turned
on. The setting up of contrast, brig-
htness and volume.
Adjust color control
Adjust channel again
The following problems are not always caused by hardware failure, please use the
follow trouble shooting guide before you call for service:
?
Picture with Snow
No Color
No Picture
Normal
Disturb
Double or Triple Image
Noise
Normal
Noise
No Sound
No Sound
Normal Volume
Normal or Weak Volume
??
Scramble
3.Do not let the TV set stay in the still image for a long time, because the screen
will appear the residual image. If appear, within 12 hours the TV set will
recover to be normal automatically after you switch the TV set to dynamic
image .
/