AIRSLED Sub-Zero Series User manual

Brand
AIRSLED
Model
Sub-Zero Series
Type
User manual

AIRSLED Sub-Zero Series

AIRSLED Sub-Zero Series adapters are designed to ensure that air beams safely lift a Sub-Zero® refrigerator by the appropriate structural contact points. With the help of the adapters, you may move your Sub-Zero® refrigerator with decreased risk.

Here are some of the capabilities of the AIRSLED Sub-Zero Series adapters:

  • Designed to fit Sub-Zero® refrigerators
  • Safely lifts Sub-Zero® refrigerators by the appropriate structural contact points
  • Minimizes possible tilting during load movement
  • Front supports may be adjusted to correct any variance between the front and rear gap

AIRSLED Sub-Zero Series

AIRSLED Sub-Zero Series adapters are designed to ensure that air beams safely lift a Sub-Zero® refrigerator by the appropriate structural contact points. With the help of the adapters, you may move your Sub-Zero® refrigerator with decreased risk.

Here are some of the capabilities of the AIRSLED Sub-Zero Series adapters:

  • Designed to fit Sub-Zero® refrigerators
  • Safely lifts Sub-Zero® refrigerators by the appropriate structural contact points
  • Minimizes possible tilting during load movement
  • Front supports may be adjusted to correct any variance between the front and rear gap
User Guide
Airsled Sub-Zero
®
Adapters
Page 1 of 2
70 – A Aleph Dr.
Newark, DE 19702
Support Email: [email protected]
Toll Free Number: 1-800-AIRSLED (1-800-247-7553)
USING AIRSLEDS SUB-ZERO
®
ADAPTERS
Airsled’s Sub-Zero
®
adapters are designed to ensure that the air beams safely lift a Sub-Zero
®
refrigerator
by the appropriate, structural contact points. Follow the below procedure when using this accessory:
• Prepare the work environment by ensuing objects on, inside or near the refrigerator are removed
and/or secured.
• Remove any bendable or breakable features at the base such as front grill cover and drip pan.
• Confirm that there are no other breakable components hanging down that could prevent the adapters
from making contact at the desired points of the refrigerator’s base.
• Slide the Airsled air beams under the refrigerator.
• Remove the rear metal pins and wood block and place the metal rails sideways on the air beams and
then rotate so they are both are upright. See figure 1. This is done before sliding on the wood block
supports.
• With the rails upright, slide the wooden blocks into the desired slot. There are two slots. One is for a 3
¼” height and the other is for a 3 ½” height. Select your desired slot. See figure 2.
• Insert the rear pins back into the rails. See figure 3.
• Ideally, the gap between the adapters and the refrigerator’s base will be uniform. This will minimize
possible tilting during load movement. The adapters’ front supports may need to be adjusted to
correct any variance between the front and rear gap. See figure 4.
Figure 1 (top view)
Figure 2
Figure 3
Figure 4 (adjustable front
support)
Page 2 of 2
70 – A Aleph Dr.
Newark, DE 19702
Support Email: [email protected]
Toll Free Number: 1-800-AIRSLED (1-800-247-7553)
• Ensure that the adapters only make contact with the structural cabinet when the air beams are
inflated and not any breakable/bendable components such as rear cover or front door. See figure 5.
WARNING: Nonstructural components such as hinged doors may break if used as a lifting point.
Additionally, Sub-Zero
®
refrigerators tend to be top heavy so use extreme caution when moving.
• Figure 6 illustrates the correct orientation
of the adapters relative to the air beams.
Keeping the adapters and load centered
to the air beams promotes more optimal
Airsled performance.
Figure 5 (side view of adapters under the refrigerator – not to scale)
Figure 6
  • Page 1 1
  • Page 2 2
  • Page 3 3

AIRSLED Sub-Zero Series User manual

Brand
AIRSLED
Model
Sub-Zero Series
Type
User manual

AIRSLED Sub-Zero Series

AIRSLED Sub-Zero Series adapters are designed to ensure that air beams safely lift a Sub-Zero® refrigerator by the appropriate structural contact points. With the help of the adapters, you may move your Sub-Zero® refrigerator with decreased risk.

Here are some of the capabilities of the AIRSLED Sub-Zero Series adapters:

  • Designed to fit Sub-Zero® refrigerators
  • Safely lifts Sub-Zero® refrigerators by the appropriate structural contact points
  • Minimizes possible tilting during load movement
  • Front supports may be adjusted to correct any variance between the front and rear gap
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents