Rockwell RK2510K2.1 User manual

12 V CORDLESS DRILL/DRIVER PAGE 4 ENG

12 V OLTIOS TALADRO INALAMBRICO PAGE 11 ESP

PERCEUSE/TOURNEVIS À 12 V PAGE 19 FRE

RK2510/RK2510K

RK2510K2/RK2510K2.1

Page is loading ...

12 V CORDLESS DRILL/DRIVER ENG

4

COMPONENT LIST

KEYLESS CHUCK

TORQUE ADJUSTMENT RING

TWO-SPEED GEAR CONTROL

FORWARD/REVERSE ROTATION CONTROL

SOFT GRIP HANDLE

BATTERY PACK RELEASE BUTTON

BATTERY PACK *

ON/OFF SWITCH

LED LIGHT

* Not all the accessories illustrated or described are included in standard delivery.

ACCESSORIES

We recommend that you purchase your accessories

from the same store that sold you the tool. Use good

quality accessories marked with a well-known brand

name. Choose the type according to the work you intend

to undertake. Refer to the accessory packaging for

further details. Store personnel can assist you and offer

advice.

GENERAL POWER TOOL SAFETY

WARNINGS

WARNING: Read all safety warnings and

instructions. Failure to follow the warnings

and instructions may result in electric shock, ﬁre and/

or serious injury.

Save all warnings and instructions for future

reference.

The term power tool in the warnings refers to your

electric (corded) power tool or battery-operated

(cordless) power tool.

1. WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

1

2

3

4

5

6

7

8

9

RK2510K2

RK2510K2.1

RK2510 RK2510K

Double ended bit 1 1 1 1

Battery pack

(RW9300)

2 2 / 1

Charger (RW9400) 1 1 / 1

PUCK

TM

Magnetic bit

holder

/ 1 / /

PH1, PH2(X2),

PH3

/ 4 / /

SQ1,

SQ2(X2), SQ3

/ 4 / /

6-8, 8-10 / 2 / /

T15, T20, T25 / 3 / /

4,5 / 2 / /

12 V CORDLESS DRILL/DRIVER ENG

5

2. ELECTRICAL SAFETY

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do not use

any adapter plugs with grounded power tool.

Unmodiﬁed plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with grounded surfaces

such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use

marked “W-A” or “W”. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a Ground Fault Circuit

Interupter (GFCI) protected supply. Use of a

GFCI reduces the risk of electric shock.

3.

PERSONAL SAFETY

a) Stay alert, watch what you are doing and

use common sense when operating a power

tool. Do not use a power tool while you are

tired or under the inﬂuence of drugs, alcohol

or medication. A moment of inattention while

operating power tools may result in serious personal

injury.

b) Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your ﬁnger on the switch or energizing power tools

that have the switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control of

the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewelery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewelery

or long hair can be caught in moving parts.

g)

If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

4. POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the rate

for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and off. Any power tool that cannot

be controlled with the switch is dangerous and must

be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions

to operate the power tool.Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits

etc., in accordance with these instructions

and in the manner intended for the particular

12 V CORDLESS DRILL/DRIVER ENG

6

type of power tool, taking into account

the working conditions and the work to be

performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

h) Use clamps or another practical way to secure and

support the workpiece to a stable platform.

i) Holding the work by hand or against your body

leaves it unstable and may lead to loss of control.

5. BATTERY TOOL USE AND CARE

a) Recharge only with the charger speciﬁed by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of ﬁre

when used with another battery pack.

b) Use power tools only with speciﬁcally

designated battery packs. Use of any other

battery packs may create a risk of injury and ﬁre.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from

one terminal to another. Shorting the battery

terminals together may cause burns or a ﬁre.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, ﬂush with water.

If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may

cause irritation or burns.

6. SERVICE

a) Have your power tool serviced by a

qualiﬁed repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

WARNING: Some dust created by power

sanding, sawing, grinding, drilling and

other construction activities contains chemicals

known to the state of California to cause cancer,

birth defects or other reproductive harm. Some

examples of these chemicals are:

• Leadfromlead-basedpaints.

• Crystallinesilicafrombricksandcementand

other masonry products and.

• Arsenicandchromiumfromchemically-

treated lumber.

Y

our risk from these exposures varies, depending on

how often you do this type of work. To reduce your

exposure to these chemical: work in a well ventilated

area, and work with approved safety equipment,

such as those dust masks that are specially designed

to ﬁlter out microscopic

particles.

ADDITIONAL SAFETY RULES FOR

YOUR CORDLESS DRILL

1. Battery leakage may occur under extreme usage

or temperature conditions. If the ﬂuid comes into

contact with the eyes, ﬂush with water for several

minutes and contact a doctor immediately.

2. Never burn batteries, they can explode in a ﬁre.

3. Do not charge a leaking battery.

4. Use of an attachment and charger not recommended

or sold by the drill manufacturer may result in a risk

of ﬁre, electric shock, or injury to persons.

5. Before drilling into a wall or blind area, make

certain there is no danger of drilling into electric,

gas or water supply lines. Use and metal or voltage

detector if there is doubt.

6. Before you lay down the drill, make sure that all

moving parts have come to a stop.

7. Avoid frequent stalling when drilling, as this could

damage the batteries.

8. Only connect the charging device to an AC supply.

9.

Charge battery only with the appropriate charging device.

10. The charging device and the drill must be protected

from moisture!

11. Do not use the charging device outdoors.

12. Always charge the battery pack between

temperatures 36ºF to 95ºF (2

o

C to 35

o

C). Ideal

charging temperature is 65ºF to 84ºF (18

o

C to 29

o

C).

13. Do not short out the contacts of battery or charger.

14. Respect the polarity “+/-“when charging.

15. Save these instructions. Refer to them frequently

and use them to instruct others who may use this

tool. If someone borrows this tool, make sure they

have these instructions.

16. Use auxiliary handles supplied with the tool.

Loss of control can cause personal injury.

17. Wear ear protection with cordless drill.

Exposure to noise can cause hearing loss.

18. Hold power tool by insulated gripping

surfaces, when performing an operation

where the fastener may contact hidden

wiring. Fasteners contacting a “live” wire may

12 V CORDLESS DRILL/DRIVER ENG

7

make exposed metal parts of the power tool live and

could give the operator an electric shock.

WARNING! If a small amount of electrolyte

should leak from the battery pack under

extremes of temperature or after heavy use, then

wash off immediately from your skin and hands

using clean water. For eye contact, rinse thoroughly with

clean water and seek medical treatment

immediately.

SYMBOLS

To reduce the risk of injury, user must read

instruction manual.

Warning

Wear ear protection

Wear eye protection

Wear dust mask

Indoor use only

Do not expose to rain or water

Do not burn

Direct current

12 V CORDLESS DRILL/DRIVER ENG

8

TECHNICAL DATA

Charger voltage 120 V~60 Hz

Voltage 12 V

No-load speed 0-350/0-1300/min

Number of clutch positions 15+1

Max torque 210 in.lbs

Check capacity 3/8˝

Max. drilling capacity Steel 3/8˝

Wood 13/16˝

Machine weight 2.2 lbs

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the instruction

book carefully.

CHARGING

A) BATTERY CHARGING

The battery charger supplied is matched to the Li-ion

battery installed in the machine. Do not use another

battery charger.

The Li-ion battery is protected against deep

discharging. When the battery is empty, the machine is

switched off by means of a protective circuit: The chuck

no longer rotates.

In a warm environment or after heavy use, the battery pack

may become too hot to permit charging. Allow time for the

battery to cool down before recharging.

When the battery is charged for the ﬁrst time and

after prolonged storage, the battery will only accept

approximately 60% charge. However, after several charge

and discharge cycles the battery will accept a 100% charge.

B) TO REMOVE OR INSTALL BATTERY PACK (SEE A)

Depress the battery pack release button to release and

slide the battery pack out from your tool. After recharge,

slide it back into your tool. A simple push and slight

pressure will be sufﬁcient.

OPERATION

1. ON / OFF SWITCH (SEE B)

Depress the On/Off switch to start and release it to stop

your drill. The on/off switch is ﬁtted with a brake function

which stops your chuck immediately when you quickly

release the switch.

It is also a variable speed switch that delivers higher

speed and torque with increased trigger pressure. Speed

is controlled by the amount of switch trigger depression.

WARNING: Do not operate for long periods

at low speed because excess heat will be

produced internally.

2. SWITCH LOCK

The switch trigger can be locked in the OFF position. This

helps to reduce the possibility of accidental starting when

not in use. To lock the switch trigger, place the rotation

control in the center position.

3. REVERSIBLE (SEE B)

For drilling and screw driving use forward rotation

marked “

” (lever is moved to the left). Only use

reverse rotation marked “

” (lever is moved to the

right) to remove screws or release a jammed drill bit.

WARNING: Never change the direction of

rotation when the chuck is rotating, wait

until it has stopped!

4. TWO-SPEED GEAR CONTROL (SEE C)

The drill has a two-speed gear control designed for

drilling or driving at LO (mark is 1) or HI (mark is 2)

speeds. A slide switch is located on top of the drill to

select either LO or HI speed. When using the drill in the

LO speed range, the speed will decrease and the drill will

have greater power and torque. When using the drill in

the HI speed range, the speed will increase and the drill

will have less power and torque.

Gear I

Low speed range: For screwdriving or working with large

drilling diameter.

Gear II

High speed range: For working with small drilling diameter.

WARNING: To prevent gear damage,

always allow the chuck to come to a

complete stop before changing the direction of

rotation or the two-speed gear control.

5. CHUCK ADJUSTMENT (SEE D)

To open the chuck jaws rotate the front section of the

chuck. Insert the drill bit between the chuck jaws and

rotate the front section in the opposite direction. Ensure

the drill bit is in the center of the chuck jaws. Finally,

ﬁrmly rotate the front chuck section in the opposite

directions. Your drill bit is now clamped in the chuck.

6. TORQUE ADJUSTMENT (SEE E)

(Screw driving force of your drill driver)

The torque is adjusted by rotating the torque adjustment

ring. The torque is greater when the torque adjustment

ring is set on a higher setting. The torque is less when

the torque adjustment ring is set on a lower setting.

Make the setting as follows:

1 - 4 for driving small screws

5 - 9 for driving screws into soft material

10-15 for driving screws into soft and hard material

for heavy drilling

12 V CORDLESS DRILL/DRIVER ENG

9

7. AUTOMATIC SPINDLE LOCK (SEE F)

The automatic spindle lock allows you to use it as a

regular screwdriver. You can give an extra twist to ﬁrmly

tighten a screw, loosen a very tight screw or continue

working when the battery energy has expired. For

manual screwdriver purposes, the chuck is automatically

locked when the tool is off.

8. USING THE LED LIGHT

The sight light allows you to keep a clear view under less

illuminated circumstances. To turn on the light simply

press the on/off switch. When you release the on/off

switch, the light will be off.

LED is also a battery capacity indicator. It will ﬂash when

power gets low.

9. DRILLING

When drilling into a hard smooth surface, use a center

punch to mark the desired hole location. This will prevent

the drill bit from slipping off center as the hole is started.

Hold the tool ﬁrmly and place the tip of the bit at the

point to be drilled. Depress the switch trigger to start the

tool. Move the drill bit into the workpiece, applying only

enough pressure to keep the bit cutting. Do not force or

apply side pressure to elongate a hole.

Tungsten carbide drill bits should always

be used for concrete and masonry. When

drilling in metal, only use HSS drill bits in good

condition. Always use a magnetic bit holder (not

included) when using short screwdriver bits.

When screw-driving, apply a small quantity of

liquid soap or similar to the screw threads to

ease insertion.

10. DISPOSAL OF AN EXHAUSTED BATTERY PACK

To preserve natural resources, please recycle

or dispose of the battery pack properly. This

battery pack contains Lithium batteries.

Consult your local waste authority for information

regarding available recycling and/or disposal options.

Discharge your battery pack by operating your drill, then

remove the battery pack from the drill housing and cover

the battery pack connections with heavy-duty adhesive

tape to prevent short circuit and energy discharge. Do

not attempt to open or remove any of the components.

PROBLEM SOLUTION

1. WHY DOES THE DRILL NOT TURN ON WHEN YOU

PRESS THE SWITCH?

The forward/reverse rotation control, which is on top of

the trigger, is positioned in the lock function. Unlock the

forward/reverse rotation control by putting it into the

required rotation position. Push the trigger and the drill

will start to rotate.

2. THE DRILL STOPS BEFORE THE SCREW IS

COMPLETELY TIGHTENED. WHY?

Verify the torque position of the torque adjusting ring,

you can ﬁnd the torque-adjusting ring between the

chuck and the drill body. Position 1 is the lowest torque

(screw driving force) and position 15 is the highest

torque (screw driving force). Position 16 is for drill

operation. Regulate the torque adjusting ring to a higher

position to reach the best result.

3. REASONS FOR DIFFERENT BATTERY PACK

WORKING TIMES

Charging time problems, as above, and having not

used a battery pack for a prolonged time will reduce

the battery pack working time. This can be corrected

after several charge and discharge operations by

charging and working with your drill. Heavy working

conditions such as large screws into hard wood will use

up the battery pack energy faster than lighter working

conditions. Do not re-charge your battery pack below

32°F (0°C) and above 113°F (45°C) as this will affect

performance.

MAINTENANCE

Your tool requires no additional lubrication or

maintenance.

There are no user serviceable parts in your power tool.

Never use water or chemical cleaners to clean your

power tool. Wipe clean with a dry cloth. Always store your

power tool in a dry place. Keep the motor ventilation slots

clean. Keep all working controls free of dust. Occasionally

you may see sparks through the ventilation slots. This is

normal and will not damage your power tool.

12 V CORDLESS DRILL/DRIVER ENG

10

2-YEAR WARRANTY STATEMENT

If your Rockwell tool becomes defective due to faulty

materials or workmanship within a period of 2 years

from the date of purchase, we guarantee to:

• Replaceorrepairalldefectiveparts,freeofcharge,

or.

• Repairproductsfreeofcharge,or.

• Replacetheunitwithaneworre-conditionedunit,

free of charge.

Your warranty is subject to the following conditions:

• Batterypacksareguaranteedfora12monthperiod

only.

• Thetoolhasnotbeenmisused,abused,neglected,

altered, modiﬁed or repaired by anyone other than

an authorized service center.

• OnlygenuineRockwellaccessoriesandpartshave

been used on or with the product

• Thetoolhasbeensubjectedtofairwearandtear.

• Thetoolhasnotbeenusedforrentalpurposes.

• Thetoolhasnotsustaineddamagethroughforeign

objects, substances or accidents.

Your warranty does not cover:

• Componentsthataresubjecttonaturalwearand

tear caused by use in accordance with operating

instructions.

• Unauthorized/impropermaintenance/handlingor

overload are excluded from this warranty as are

accessories such as bulbs, blades and bits, etc.

For guarantee claims, please contact the Rockwell

Helpline and you will need to submit a proof of purchase

in the form of a valid receipt that displays date and place

of purchase.

We may require the tool be sent postage prepaid to

an authorized service center, along with all original

equipment.

Rockwell Helpline 866-514-ROCK(7625)

This guarantee statement does not replace but is in

addition to your statutory rights.

This warranty does not apply to accessories supplied

with the tool.

This warranty applies only to the original purchaser and

may not be transferred.

All repairs and replacement tools will be covered by the

limited warranty for the balance of the warranty period

from the date of the original purchase.

Limited 30-Day exchange policy

During the ﬁrst 30 days after date of purchase, you may

exchange a tool which does not work properly due to

defects in materials or workmanship by returning the

power tool to the retailer where it was purchased. To

receive a replacement power tool, you must present

a dated proof of purchase and return all original

equipment packaged with the original product. The

replacement power tool will be covered by the limited

warranty for the balance of the two year period from the

date of the original purchase.

Page is loading ...

Rockwell RK2510K2.1 User manual

This manual is also suitable for

Rockwell RK2510K2.1 User manual

in other languages

Related papers

Other documents