5019 307 00122
1. Check that all fastenings are closed and that
pockets are empty.
2. Turn the articles inside out.
3. Place laundry loosely in the drum to make
sure it doesn’t become tangled.
Sort laundry as follows:
A) By care symbols
(on the collar or inside seam):
Suitable for tumble drying
Tumble drying with reduced drying
intensity only
Do not tumble dry
B) By amount and thickness/weight
Whenever the load to be dried exceeds dryer
capacity, separate laundry according to
weight (e.g. towels from thin underwear).
C) By type of fabrics
Cotton/linen
: Towels, cotton jersey, bed
and table linen made of cotton or linen.
Synthetics/Easy Care
: blouses, shirts,
overalls, etc. made of polyester or
polyamide, as well as cotton/synthetic
mixes.
D) By drying level
• Sort into: iron dry, cupboard dry, etc.
Do not tumble dry:
Woollens, silk, nylon
stockings, delicate embroidery, fabrics with
metallic decorations, bulky items such as
sleeping bags, etc.
Important: only use specific indicated dryer-
safe additives
and rinse items that have been
treated with stain remover thoroughly in plenty
of water before drying.
Only use specific
indicated dryer-safe plastic items
and
never
dry
rubber or articles contaminated with
vegetable oil
in the dryer.
Programme and Options:
• To select a programme, turn the programme
selector knob. The Start/Pause indicator
lamp is blinking ““, indicating that the
cycle needs to be started.
• To select an option, press the corresponding
button. The indicator lamp in the button
confirms that a selection has been made.
• Press the button again to cancel the option.
1. Having selected the desired programme and
options, press the Start button.
If the laundry is not removed at the end of
the drying cycle, an automatic anti-crease
cycle will operate for maximum 60 min. The
drum rotates at regular intervals, preventing
the laundry from creasing.
This Anti-Crease cycle can be extended up to
12h when Anti-Crease option has been
selected.
2. On completion of the programme, set the
programme selector knob to position
“0”
.
When changing the programme during the drying
cycle, the dryer stops. The Start/Pause indicator
lamp is blinking ““.
To operate the new programme, press the Start/
Pause ““ button again.
To interrupt the dryer during operation
1. Set the programme selector knob to
Airing ““.
2. Press the Start button.
Wait at least 5 minutes before opening the
door to allow the dryer to cool down.
For your safety the programme stops
automatically if you open the door.
3. To restart, after door opening, close the door
and press theStart/Pause ““ button
again.
Clean the lint filter at the end of every
drying cycle:
1. Open the door.
2. Pull the filter upwards.
3. Remove lint using a soft brush or your
fingertips.
4. Push the filter back into place.
If a fault occurs, before contacting our After-
Sales Service, make the following checks to try
and remedy the problem:
Drying takes too long / laundry is not dry
enough:
• Was the correct programme selected?
• Was the inserted laundry too wet (Washing
machine spin speed less than 800 rpm)?
• Is the lint filter dirty (filter indicator lamp on)?
The dryer does not operate:
(after a power failure and/or interruption to the
mains supply, always press the Start button).
• Is the plug properly inserted into the mains
electricity socket?
• Is there a power failure?
• Has the fuse blown?
• Is the door well closed?
• Has the programme been selected?
• Has the
Start/Pause
““ button been
pressed?
Lint filter indicator lamp light on:
• Is the lint filter clean?
• Is the vent hose blocked?
All programme sequence indicators blinking:
• Service call necessary.
If, after carrying out the above checks the
malfunction persists or appears again, turn
the dryer off and call our After-Sales Service
(refer to guarantee).
Please specify:
• The nature of the fault.
• The dryer type and model.
• The service code (the number after the word
Service on the adhesive rating plate) on the
right-hand side when the door is open.
• Your full address and phone number.
PREPARING THE LAUNDRY SELECTING A PROGRAMME & OPTIONS
STARTING & COMPLETING A PROGRAMME
CHANGING A PROGRAMME
INTERRUPTING A PROGRAMME
DAILY MAINTENANCE & CLEANING
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE