Parkside PEC 200 SE Owner's manual

Type
Owner's manual

Parkside PEC 200 SE is a versatile power scraper suitable for removing coverings, residues, smoothing surfaces, and carving soft woods. Its adjustable stroke rate (three levels) and various attachments (knife, scraper, spatula, chisel) allow for precise and efficient work. Safety features include an ON/OFF switch with stroke rate preselector, a tool arrestor, and the requirement to wear protective gear (hearing protection, dust mask, safety glasses, and gloves) while operating the device.

Parkside PEC 200 SE is a versatile power scraper suitable for removing coverings, residues, smoothing surfaces, and carving soft woods. Its adjustable stroke rate (three levels) and various attachments (knife, scraper, spatula, chisel) allow for precise and efficient work. Safety features include an ON/OFF switch with stroke rate preselector, a tool arrestor, and the requirement to wear protective gear (hearing protection, dust mask, safety glasses, and gloves) while operating the device.

PEC 200 SE
6
POWER SCRAPER
Operation and Safety Notes
POWER SCRAPER
30164_Elektroschaber_Cover_LB6.indd 2 09.04.09 09:16
GB / IE / CY Operation and Safety Notes Page 5
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the
device.
30164_Elektroschaber_Cover_LB6.indd 3 09.04.09 09:16
1
2
4
3
5678
A
E
B
F
C D
G
30164_Elektroschaber_Cover_LB6.indd 4 09.04.09 09:16
5 GB/IE/CY
Table of Content
Introduction
Intended Utilisation .......................................................................................................Page 6
Fittings ............................................................................................................................Page 6
Items supplied ...............................................................................................................Page 6
Technical Data ..............................................................................................................Page 7
General safety advice for electrical power tools
1. Workplace safety .....................................................................................................Page 7
2. Electrical safety ........................................................................................................Page 7
3. Personal safety .........................................................................................................Page 8
4. Careful handling and use of electrical power tools ..............................................Page 8
Safety advice for electric scraper / carver .................................................................Page 9
Original ancillaries / accessories ................................................................................Page 9
Understood everything? ...............................................................................................Page 9
Before taking tool into use
Attachment tools ...........................................................................................................Page 9
Changing attachments .................................................................................................Page 10
Commissioning
Working Notices ..........................................................................................................Page 10
Switching ON / OFF .....................................................................................................Page 10
Selecting the stroke rate ...............................................................................................Page 10
Resharpening the attachment tools .............................................................................Page 10
Maintenance and cleaning ........................................................................Page 11
Disposal ......................................................................................................................Page 11
Information
Service centre ...............................................................................................................Page 11
Warranty .......................................................................................................................Page 11
Declaration of Conformity / Manufacturer .................................................................Page 12
30164_Elektroschaber_Content_LB6.indd 5 09.04.09 09:14
6 GB/IE/CY
Introduction
Power scraper
Q
Introduction
Please make sure you familiarise your-
self fully with the way the device works
before you use it for the first time and
that you understand how to handle electrical pow-
er tools correctly. To help you do this please read
the accompanying operating instructions. Keep
these instructions in a safe place. If you pass the
device on to anyone else, please ensure that you
also pass on all the documentation.
Q
Intended Utilisation
The appliance is suitable for the removal and abra-
sion of coverings such as carpets, felts, cork sheets
and plaster on small areas. It is also intended for
removing residues of adhesives, paints and fillers,
for the smoothing of coarse surfaces as well as for
carvings on soft woods. Any other use of, and
modification to, the appliance is deemed to be
improper usage and may result in serious physical
injury. The manufacturer declines to accept respon-
sibility for damage(s) arising out of usage contrary
to the instructions specified below. The appliance is
not intended for commercial application.
Q
Fittings
1 ON / OFF switch / Stroke rate preselector
2 Tool arrestor
3 Tool receptor
4 Tool attachment
5 Knife / Scraper attachment (offset)
6 Knife / Scraper attachment (straight)
7 Spatula attachment
8 Chisel attachment
Q
Items supplied
1 Power scraper
1 Knife / Scraper attachment (offset)
The following pictograms are used in these operating instructions / on the device:
Read instruction manual! Safety class II
Observe caution and safety notes!
Wear hearing protection, dust
protection mask, protective glasses
and protective gloves.
Caution electric shock!
Danger to life!
Keep children away from electrical
power tools!
Explosive material! Protect electrical power tools from
moisture!
n0Nominal stroke rate Check that the device, mains lead
and plug are in good condition!
V~Volt (AC) Dispose packaging and appliance in
an environmentally-friendly way!
WWatts (Effective power)
30164_Elektroschaber_Content_LB6.indd 6 09.04.09 09:14
7 GB/IE/CY
Introduction / General safety advice for electrical power tools
1 Knife / Scraper attachment (straight)
1 Spatula attachment
1 Chisel attachment
1 Operating manual
Q
Technical Data
Rated voltage: 230 V ~ 50 Hz
Nominal power consumption:
200 W
Nominal stroke rate: Level I: n0 6.500 min-1
Level II: n0 7.500 min-1
Level III: n0 8.500 min-1
Stroke: ca. 2 mm
Protection class: II /
Noise and vibration data:
Values determined in accordance with EN 60745.
The sound pressure level (A-weighted) of the device
is typically 78 dB (A). Uncertainty K = 3 dB. The
sound level while working can exceed 85 dB (A).
Wear ear protection!
Evaluated acceleration, typical:
Hand / arm vibration ah = 8 m / s2
Uncertainty K = 1,5 m / s2
WARNING! The vibration level given in these
instructions has been measured in accordance with
a standardised measurement procedure specified
in EN 60745 and can be used to compare devices.
Different uses of the device give rise to different vibra-
tion levels and in many cases they may exceed the
values given in these instructions. It is easy to underes-
timate the vibration load if the electrical power tool is
used regularly in particular circumstances.
Note: If you wish to make an accurate assessment
of the vibration loads experienced during a particu-
lar period of working, you should also take into
account the intervening periods of time when the
device is switched off or is running but is not actually
in use. This can result in a much lower vibration
load over the whole of the period of working.
General safety advice for
electrical power tools
WARNING! Read all the safety advice
and instructions!
Failure to observe the safety advice and instructions
may result in electric shock, fire and / or serious injury.
KEEP ALL THE SAFETY ADVICE AND INSTRUC-
TIONS IN A SAFE PLACE FOR FUTURE REFER-
ENCE! THE TERM “ELECTRICAL TOOL” USED
IN THE SAFETY ADVICE REFERS TO ELECTRICAL
TOOLS POWERED BY MAINS ELECTRICITY (BY
MEANS OF A MAINS LEAD) AND ELECTRICAL
TOOLS POWERED BY RECHARGEABLE BATTER-
IES (WITHOUT A MAINS LEAD).
1. Workplace safety
a) Keep your working area clean and
well lit. Untidy or poorly lit working areas
can lead to accidents.
b) Do not work with the device
in potentially explosive envi-
ronments in which there are
inflammable liquids, gases or dusts.
Electrical power tools create sparks, which can
ignite dusts or fumes.
c) Keep children and other
people away while you are
operating the electrical tool.
Distractions can cause you to lose control of
the device.
2. Electrical safety
To avoid danger to life from
electric shock:
a)
The mains plug on the device must match
the mains socket. The plug must not
be modified in any way. Do not use
an adapter plug with devices fitted
with a protective earth. Unmodified
plugs and matching sockets reduce the risk of
electric shock.
30164_Elektroschaber_Content_LB6.indd 7 09.04.09 09:14
8 GB/IE/CY
General safety advice for electrical power tools
b) Avoid touching earthed surfaces such
as pipes, radiators, ovens and refrig-
erators with any part of your body.
There is an increased risk of electric shock if
your body is earthed
.
c) Keep the device away from
rain or moisture. Water entering
an electrical device increases the
risk of electric shock.
d) Do not use the mains lead for
any purpose for which it was
not intended, e.g. to carry the
device, to hang up the device or to pull
the mains plug out of the mains socket.
Keep the mains lead away from heat,
oil, sharp edges or moving parts of the
device. Damaged or tangled mains leads
increase the risk of electric shock.
e) When working outdoors with an electri-
cal power tool always use extension ca-
bles that are also approved for use out-
doors. The use of an extension cable suitable for
outdoor use reduces the risk of electric shock.
f) Use a residual current device (RCD)
for protection if operating the electri-
cal power tool in a moist environment
is unavoidable. The use of an RCD reduces
the risk of electric shock.
3. Personal safety
a) Remain alert at all times, watch what
you are doing and always proceed
with caution. Do not use the device if
you are tired or under the influence of
drugs, alcohol or medication. One mo-
ment of carelessness when using the device
can lead to serious injury.
b) Wear personal protective
equipment and always wear
safety glasses. The wearing of
personal protective equipment such as dust
masks, non-slip safety shoes, safety helmets or
ear protectors, appropriate to the type of elec-
trical power tool used and work undertaken,
reduces the risk of injury.
c) Avoid unintentional operation of the
device. Check that the electrical power
tool is switched off before you connect
it to the mains, pick it up or carry it.
Accidents can happen if you carry the device
with your finger on the ON / OFF switch or with
the device switched on.
d) Remove any setting tools or spanners
before you switch the device on. A tool
or spanner left attached to a rotating part of a
device can lead to injury.
e) Avoid placing your body in an unnat-
ural position. Keep proper footing
and balance at all times. By doing this
you will be in a better position to control the
device in unforeseen circumstances.
f) Wear suitable clothing. Do not wear
loose clothing or jewellery. Keep your
hair, clothing and gloves clear of mov-
ing parts. Loose clothing, jewellery or long
hair can become trapped in moving parts.
g) If vacuum dust extraction and collection
devices are fitted do not forget to
check
that they are properly connected
and
correctly used. The use of these devices re-
duces the hazard presented by dust.
4. Careful handling and use of
electrical power tools
a) Do not overload the device. Always
use an electrical power tool that is
intended for the task you are under-
taking. By using the right electrical power
tool for the job you will work more safely and
achieve a better result.
b) Do not use an electrical power tool if
its switch is defective. An electrical power
tool that can no longer be switched on and off
is dangerous and must be repaired.
c) Pull the mains plug out of the socket
before you make any adjustments to
the device, change accessories or when
the device is put away. This precaution is
intended to prevent you from unintentionally
starting the device.
30164_Elektroschaber_Content_LB6.indd 8 09.04.09 09:14
9 GB/IE/CY
General safety advice for electrical power tools / Before taking tool into use
d) When not in use always ensure that
electrical power tools are kept out of
reach of children. Do not let anyone use
the device if he or she is not familiar
with it or has not read the instructions
and advice. Electrical power tools are danger-
ous when they are used by inexperienced people.
e) Look after the device carefully. Check
that moving parts are working prop-
erly and move freely. Check for any
parts that are broken or damaged
enough to detrimentally affect the
functioning of the device. Have dam-
aged parts repaired before you use
the device. Many accidents have their origins
in poorly maintained electrical power tools.
f) Keep cutting tools clean and sharp.
Carefully maintained cutting tools with sharp
cutting edges are less likely to jam and are
easier to control.
g) Use the electrical power tool, accesso-
ries, inserted tools etc. in accordance
with these instructions and advice,
and the stipulations drawn up for this
particular type of device. In doing this,
take into account the working condi-
tions and the task in hand. The use of
electrical power tools for purposes other than
those intended can lead to dangerous situations.
Safety advice for
power scraper
Avoiding the danger of injury, fire and
damage to your health:
J Securely support the workpiece. Use
clamps or a vice to grip the workpiece
firmly. This is much safer than holding it in
your hand.
J Wear protective glasses! Pieces
of material may split off the work-
piece and become projectiles.
This could cause injury.
J Wear a dust mask! A dust mask
must be worn for prolonged work on
wood or when working on materials
that give rise to hazardous dusts.
J Do not soak the materials or the area
to be worked with liquids containing
solvents. Unhealthy / poisonous gases may
develop from the heat generated by scraping.
J Materials containing asbestos may
not be worked. Asbestos is considered to
be a carcinogen.
J Under no circumstances should you
place your hands next to or in front of
the appliance or on the area to be
worked, you could be seriously injured if you
slip or stumble.
J Always have the cable leading away to the
rear of the appliance.
J In the event of danger, immediately remove the
plug from the power socket.
Q
Original ancillaries / accessories
J Use only the ancillaries and accessories
that are detailed in the operating in-
structions. The use of ancillaries and acces-
sories other than those recommended in the
operating instructions could lead to an increased
risk of personal injury for you.
Q
Understood everything?
J When you have made yourself familiar with
these general safety instructions for electrical
hand tool, then you can start with the work. You
will work at your safest when taking note of the
manufacturer‘s declarations and instructions.
Q
Before taking tool into use
Q
Attachment tools
The choice of the correct attachment tool is depend-
ant on the job to be done.
The supplied accessories are suitable for the most
widespread areas of application (see Figs. C, D, E
and F).
30164_Elektroschaber_Content_LB6.indd 9 09.04.09 09:14
10 GB/IE/CY
Before taking tool into use / Commissioning
5 Knife / Scraper attachment (offset)
6 Knife / Scraper attachment (straight), e.g. for
removing carpets, felts, cork sheets as well as
plaster and adhesive residues (see Fig. C, E)
7 Spatula attachment (flat), e.g. for removing
paint residues, silicon and foams (see Fig. D)
8 Chisel attachment (flat), e.g. for carving soft
woods (see Fig. F)
Q
Changing attachments
Wear suitable protective gloves when
inserting and testing attachments tool.
Notice: The curve / working edge of the attachment
tool 4 must always point downwards.
Inserting a tool attachment:
j Push the tool lock 2 forwards to “UNLOCK”.
j Insert the attachment tool 4 as far as it will go
in the tool receptor 3 (see Fig. A).
j Push the tool lock 2 backwards to “LOCK” -
the tool attachment is locked.
Removing a tool attachment:
j Push the tool lock 2 forwards to “UNLOCK”.
j Remove the inserted tool attachment 4 from
the tool receptor 3.
Q
Commissioning
The voltage of the power source must tally with the
details given on the rating plate of the appliance.
Appliances requiring 230 V can also be run on 220 V.
Q
Working Notices
j Always work away from the body.
j Hold the appliance with both hands (see Fig. B).
j Introduce the attachment tool 4 to the material
or the area to be worked with the appliance
switched on. In that the working motion of the
appliance first takes place on contact with the
material, you will achieve a much more accu-
rate positioning of the attachment tool.
Q
Switching ON / OFF
Notice: The working motion of the appliance first
takes place on material contact.
Switching on:
j Push the ON / OFF switch / Stroke rate prese-
lector 1 forwards.
Switching off:
j ON / OFF switch / Stroke rate preselector 1
backwards.
Q
Selecting the stroke rate
Note: The optimal stroke rate is dependant on
the material or the surface to be worked. It is best
determined by simple trial and error. Always start
off with the lowest setting. Should the removal be
too slight, increase the stroke rate level for level.
j Slide the ON / OFF switch / Stroke rate prese-
lector 1 to the front to increase the stroke rate.
Level 1: low stroke rate for precision work
Level 2: moderate stroke rate
Level 3: highest stroke rate for fast removal
j Slide the ON / OFF switch / Stroke rate prese-
lector 1 to the rear to decrease the stroke rate.
Q
Resharpening the
attachment tools
The best work results are only achieved with sharp
attachment tools. You should thus resharpen them
in good time.
WARNING! RISK OF INJURY! Remove
the plug from the power socket before beginning
to sharpen the tools.
j Place the attachment tool 4 to be sharpened
into the Power scraper (see section on “Chang-
ing attachments”).
30164_Elektroschaber_Content_LB6.indd 10 09.04.09 09:14
11 GB/IE/CY
Commissioning / Maintenance and cleaning / Disposal / Information
On a belt sander (e.g. Parkside PEBS 600
see Fig. G):
j Appropriately fasten the belt sander into / onto
a suitable stationary facility.
j Pay attention to the running direction of the belt
on the belt sander when resharpening.
Q
Maintenance and cleaning
WARNING! Before you clean or maintain
the device always pull the mains lead out of the
mains socket.
j Always keep the device clean, dry and free of
oil or grease.
j Regularly clean the tool receptor 3.
j Clean the attachment tools of all remains of
adhesives and other grime.
j Liquids may not be permitted to permeate into
the appliance.
j Use a soft, fluff-free cloth to clean the housing.
j Never use fuel, solvents or aggressive cleansers
that could damage plastic.
Q
Disposal
The packaging is wholly composed of
environmentally-friendly materials that can
be disposed of at a local recycling centre.
Do not dispose of electrical power
tools with the household rubbish!
In accordance with European Directive
2002 / 96 / EC
(covering waste electrical and electronic equipment)
and its transposition into national legislation, worn
out electrical power tools must be collected separately
and taken for environmentally compatible recycling.
Contact your local refuse disposal authority for
more details of how to dispose of your worn out
electrical devices.
Q
Information
Q
Service centre
J WARNING! Have your device re-
paired only by qualified specialist
personnel using original manufacturer
parts only. This will ensure that your device
remains safe to use.
J WARNING! If the plug or mains
lead needs to be replaced, always
have
the replacement carried out by the
manufacturer or its service centre. This
will ensure that your device remains safe to use.
Q
Warranty
This appliance is guaranteed for 3 years
from the date of purchase. It has been care-
fully produced and meti-culously checked
before delivery. Please keep your receipt
as proof of purchase. Contact your service
centre by telephone in case of questions
pertaining to the warranty. Your goods
can
be transmitted free of cost only in this
manner. This warranty applies only to the
initial
purchaser and is non-transferable.
The warranty covers only material or manufactur-
ing faults, not normal wear or damage to fragile
parts such as switches or rechargeable batteries.
The appliance is intended solely for private, not
commercial, use.
If this product has been subjected to improper or in-
appropriate handling, abuse, or interventions not
carried out by one of our authorised sales and
service outlets, the warranty will be considered void.
This warranty does not affect your statutory rights.
30164_Elektroschaber_Content_LB6.indd 11 09.04.09 09:14
12 GB/IE/CY
Information
GB
DES Ltd
Units 14-15
Bilston Industrial Estate
Oxford Street
Bilston (Great Britain)
WV14 7EG
Tel.: 0870 / 787-6177
Fax: 0870 / 787-6168
IE
Kompernaß Service Ireland
Tel.: 1850 930 412 (0,082 €/Min.)
* Standard call rates apply.
Mobile operators may vary.
Q
Declaration of Conformity /
Manufacturer
We, Kompernaß GmbH, Burgstr. 21,
D-44867 Bochum, Germany, declare that this
product complies with the following EU directives:
Machinery Directive
(98 / 37 / EC)
EU Low Voltage Directive
(2006 / 95 / EC)
Electromagnetic Compatibility
(2004 / 108 / EC)
Type / Device description:
Power scraper
Bochum, 30.04.2009
Hans Kompernaß
- Managing Director -
We reserve the right to make technical modifications
in the course of product development.
30164_Elektroschaber_Content_LB6.indd 12 09.04.09 09:14
Last Information Update: 04 / 2009 · Ident.-No.: PEC200SE042009-6
IAN: 30164
KOMPERNASS GMBH
Burgstraße 21
D-44867 Bochum
6
© by ORFGEN Marketing
30164_Elektroschaber_Cover_LB6.indd 1 09.04.09 09:16
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Parkside PEC 200 SE Owner's manual

Type
Owner's manual

Parkside PEC 200 SE is a versatile power scraper suitable for removing coverings, residues, smoothing surfaces, and carving soft woods. Its adjustable stroke rate (three levels) and various attachments (knife, scraper, spatula, chisel) allow for precise and efficient work. Safety features include an ON/OFF switch with stroke rate preselector, a tool arrestor, and the requirement to wear protective gear (hearing protection, dust mask, safety glasses, and gloves) while operating the device.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI