CHAUVET DJ Scorpion Bar RG User manual

User Manual

English

Español

Français

Deutsch

Nederlands

LASER LIGHT

AVOID DIRECT EYE EXPOSURE

CLASS 3R/2M LASER PRODUCT

CLASSIFIED PER EN/IEC 60825-1:2007

Complies with FDA performance standards

f

or laser products except for deviations

pursuant to Laser Notice No. 50, dated

June 24, 2007.

Complies with 21 CFR 1040, 10 and 1040, 11

except for deviations pursuant to

Laser Notice No. 50, dated, 2007.

Page 2 of 117 Kinta FX User Manual Rev. 1

TABLE OF CONTENTS

1. Before You Begin ................................................................................................................................ 7

What Is Included ....................................................................................................................................................... 7

Unpacking Instructions ............................................................................................................................................. 7

Claims ................................................................................................................................................................. 7

Manual Conventions ................................................................................................................................................. 7

Symbols .................................................................................................................................................................... 7

Disclaimer ................................................................................................................................................................. 7

Safety Notes ............................................................................................................................................................. 8

Non-Interlocked Housing Warning ...................................................................................................................... 9

Laser Safety Notes ................................................................................................................................................... 9

Laser Safety Label Reproduction ...................................................................................................................... 11

Laser Exposure Warning ................................................................................................................................... 12

Laser Emission Data ......................................................................................................................................... 12

Laser Compliance Statement ............................................................................................................................ 12

2. Introduction ....................................................................................................................................... 14

Overview ................................................................................................................................................................. 14

Dimensions ............................................................................................................................................................. 15

3. Setup ................................................................................................................................................. 16

AC Power ............................................................................................................................................................... 16

Fuse Replacement ............................................................................................................................................ 16

Power Linking .................................................................................................................................................... 17

Power Linking Diagram ............................................................................................................................... 17

Mounting ................................................................................................................................................................. 18

Orientation ......................................................................................................................................................... 18

Rigging .............................................................................................................................................................. 18

Mounting Diagram ....................................................................................................................................... 18

4. Operation ........................................................................................................................................... 19

Control Panel Operation ......................................................................................................................................... 19

Menu Map ............................................................................................................................................................... 19

Auto and Sound Modes Defined ....................................................................................................................... 19

Static Colors Defined ........................................................................................................................................ 20

Configuration (Standalone) .................................................................................................................................... 20

Sound-Active Mode ........................................................................................................................................... 20

Automatic Mode ................................................................................................................................................ 20

Speed Adjustment ............................................................................................................................................. 20

Configuration (DMX) ............................................................................................................................................... 21

DMX Personality and Starting Address ............................................................................................................. 21

Master/Slave ..................................................................................................................................................... 21

Mode ................................................................................................................................................................. 21

DMX Channel Assignments and Values ........................................................................................................... 22

9-CH ............................................................................................................................................................ 22

02CH ........................................................................................................................................................... 24

IRC-6 (Infrared Remote Control 6) Operation ................................................................................................... 25

5. Technical Information ....................................................................................................................... 26

Product Maintenance ............................................................................................................................................. 26

6. Technical Specifications .................................................................................................................. 27

Returns .................................................................................................................................................. 28

1. ANTES DE EMPAR ............................................................................................................................ 29

Page is loading ...

Kinta FX User Manual Rev. 1 Page 7 of 117

1. BEFORE YOU BEGIN

What Is

Included

• Kinta FX

• Power Cord

•

Hanging Bracket with Mounting Hardware

• Warranty card

• User Manual

Unpacking

Instructions

Carefully unpack the product immediately and check the box to make sure all the parts are in

the package and are in good condition.

Claims

If the box or the contents (the product and

included accessories) appear damaged from

shipping or show signs of mishandling, notify the carrier immediately, not Chauvet. Failure to

do so in a timely manner may invalidate your claim with the carrier. In addition, keep the

container and all the packing material for inspection.

For other issues, such as missing components or parts, damage not related to shipping, or

concealed damage, file a claim with Chauvet within 7 days of delivery.

Manual

Conventions

Convention

Meaning

1–512

A range of values

50/60

A set of values of which only one can be chosen

Settings

A menu option not to be modified

Menu > Settings

A sequence of menu options to be followed

<ENTER>

A key to be pressed on the product’s control panel

ON

A value to be entered or selected

Symbols

Symbol

Meaning

Critical installation, configuration, or operation information. Ignoring this

information can cause the product to not work, damage it, or cause harm to

the operator.

Important installation or configuration information. The product may not

function correctly if this information is not used.

Useful information.

Disclaimer

Chauvet believes that the information contained in this manual is accurate in all respects.

However, Chauvet assumes no responsibility and specifically disclaims any and all liability to

any party for any loss, damage or disruption caused by any errors or omissi

ons in this

document, whether such errors or omissions result from negligence, accident or any other

cause. Chauvet reserves the right to revise the content of this document without any obligation

to notify any person or company of such revision, however, Chauvet has no obligation to

make, and does not commit to make, any such revisions. Download the latest version from

www.chauvetlighting.com.

The works of authorship contained in this

manual, including, but not limited to, all design, text

and images are owned by Chauvet.

Electronically published by Chauvet in the United States of America.

CHAUVET, the Chauvet logo and “Kinta FX” are registered trademarks or trademarks of

Chauvet & Sons LLC (d/b/a Chauvet and Chauvet Lighting) in the United States and other

countries. Other company and product names and logos referred to herein may be trademarks

of their respective companies.

Page 8 of 117 Kinta FX User Manual Rev. 1

Safety Notes

The Safety Notes include important laser system safety information. Read and understand all

instructions before powering on the laser for the first time

. Knowing these safety instructions is

crucial to avoiding laser eye injury and breaking the law. Keep this User Manual

in a safe place

for future reference.

STOP AND READ ALL LASER SAFETY DATA

• Lasers can be hazardous and have unique safety considerations. Permanent eye injury and

blindness are possible if lasers are used incorrectly. Pay close attention to each safety

REMARK and WARNING statement in this User Manual. Read all instructions carefully

BEFORE operating this device.

• Always connect the product to a grounded circuit to avoid the risk of electrocution.

• Always disconnect the product from the power source before cleaning.

• Avoid direct eye exposure to the light source while the product is on.

• Make sure the power cord is not crimped or damaged.

• Never disconnect the product from power by pulling or tugging on the cord.

• If mounting the product overhead, always secure to a fastening device using a safety cable.

• Make sure there are no flammable materials close to the product when operating.

• Do not touch the product’s housing when operating because it may be very hot.

• This product is not intended for permanent installation.

• Always make sure that the voltage of the outlet to which you are connecting the product is

within the range stated on the decal or rear panel of the product.

• The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not expose the

product to rain or moisture.

• Always install the product in a location with adequate ventilation, at least 20 in (50 cm) from

adjacent surfaces.

• Be sure that no ventilation slots on the product’s housing are blocked.

• Never connect the product to a dimmer.

• Always use the mounting bracket to carry the product.

• Do not switch the product on/off in short intervals. This will reduce the laser diode life.

• Do not shake this product. Avoid brute force when mounting or operating this product.

• ALWAYS use a safety cable when mounting the product overhead.

• The ambient operating temperature for the laser is 59 °F to 95 °F (15 °C to 35 °C). Do not

operate this product outside this range.

• In the event of a serious operating problem, stop using the product immediately.

• Never try to repair the product. Repairs carried out by unskilled people can lead to damage

or malfunction. Contact the nearest authorized technical assistance center.

CAUTION! Use of controls, adjustments, or procedures other than THOSE specified IN

THIS USER MANUAL may result in hazardous radiation exposure.

Kinta FX User Manual Rev. 1 Page 9 of 117

• Avoid direct eye contact with laser light. Never intentionally expose your eyes or others to

direct laser light.

• This laser product can potentially cause instant eye injury or blindness if laser light directly

strikes the eyes.

• It is illegal and dangerous to shine this laser into audience areas, where the audience or

other personnel could get direct laser beams or bright reflections into their eyes.

• It is a U.S. federal offense to shine any laser at aircraft.

• Use of controls, adjustments, or procedures other than those specified in this User Manual

may result in hazardous radiation exposure.

• To eliminate wear and improve its lifespan, during periods of non-use completely disconnect

from power via breaker or by unplugging it.

• DO NOT attempt any repairs. Repairs and servicing must be carried out by a certified

technician. Unauthorized modifications are forbidden for safety reasons!

Keep this User Manual for future consultation. If transferring ownership of the product

to another user, be sure this document is kept with the laser.

Non-Interlocked

Housing Warning

• This unit contains high power laser devices internally.

• Do not open the laser housing, due to potential exposure to unsafe levels of laser radiation.

• The laser power levels, accessible if the unit is opened, can cause instant blindness, ski

n

bur

ns, and fires.

Laser Safety

Notes

STOP AND READ ALL THE LASER SAFETY NOTES BELOW

Laser light is different from any other light. Laser light can cause eye injury if the product is not

set up and used properly. Laser light is a thousand times more concentrated than any other kind

of light. This concentration can cause instant eye injuries by burning the retina (the light-

sensitive

portion at the back of the eye). The heat from a laser light cannot be felt, but it can still

injure or blind product operators and the audience. Even very small amounts of laser light at

long distances are are potentially hazardous.

DO NOT assume that ex

posure to an individual laser beam is safe, even a tiny beam split off

from a larger beam. This laser product uses dozens of milliwatts of laser power—

Class 3B

levels internally—and splits them into multiple beams—Class 3R/3B/2M

levels. The individual

Class 3R level beams are potentially hazardous to the eyes.

DO NOT

assume that a moving laser light is safe. Laser light is never without risk. Since eye

injuries can occur instantly, it is critical to prevent the possibility of ANY direct eye exposure.

According to laser safety regulations, it is not legal to aim Class 3R/3B/2M

lasers into areas

where people can be exposed, even if the laser is aimed below people’s faces, such as at a

dance floor.

Page 10 of 117 Kinta FX User Manual Rev. 1

• Do not operate the laser without first reading and understanding all the safety and technical

data in this manual.

• ALWAYS set up and install all laser effects so that any laser light is at least 3 meters

(9.8 feet) above the floor on which people are standing. See the Proper Usage section of this

manual.

• After setup, and prior to public use, test the lasers to ensure they are functioning properly.

Do not use the product if any defect is detected.

• DO NOT use laser if it is emitting only one or two beams, rather than dozens/hundreds, as

this indicates damage to the diffraction grating optic, and allows emission of laser levels

higher than Class 3R/2M/3B.

• DO NOT point lasers at people or animals.

• DO NOT look into the laser aperture or laser beams.

• DO NOT point lasers into areas where people could be exposed to them.

• DO NOT point lasers at highly reflective surfaces such as windows, mirrors, and shiny metal.

Even laser reflections can be hazardous.

• Never point a laser at aircraft; this is a U.S. federal offense.

• Never point un-terminated laser beams into the sky.

• Do not expose the output optic (aperture) to harsh cleaning chemicals.

• Do not use the laser if the housing is damaged, open, or if the optics appear damaged in any

way.

• Never open the laser housing. The high laser power levels inside of the protective housing

can start fires or burn skin, and will cause instant eye injury.

• Never leave this product running unattended.

• The operation of a Class 3R/2M/3B laser show is allowed only if the lasers are operated by a

skilled and well-trained professional, who is familiar with the data included in this manual.

• The legal requirements for using laser entertainment products vary from country to country.

The user is responsible for the legal requirements in the location/country of use.

CAUTION! Do not operate this device in ways not specified in this User Manual. Failure to follow the

instructions will void the warranty, may damage the product, or injure the user or the audience.

CAUTION! This product cannot be discarded with household waste. Contact your local waste

management service for electronic disposal regulations in your area.

Kinta FX User Manual Rev. 1 Page 11 of 117

Laser Safety Label

Reproduction

Front

Bottom

Page 12 of 117 Kinta FX User Manual Rev. 1

Laser Exposure

Warning

LASER LIGHT AVOID DIRECT EYE EXPOSURE

Further

guidelines and safety programs for safe use of lasers can be found in the ANSI Z136.1

Standard “For Safe Use of Lasers”, available from the Laser Institute of America:

www.laserinstitute.org. Many local governments, corporations, agencies, military,

and others,

require all lasers to be used under the guidelines of ANSI Z136.1. Laser Display guidance can

be obtained via the International Laser Display Association: www.laserist.org.

Laser Emission

Data

As measured under

IEC measurement

conditions for

classification.

Laser Classification

Class 3B/2M

Green Laser Medium

DPSS Nd:YVO4, 532 nm/30 mW

Red Laser Medium

LD GaAIAs, 650 nm/100 mW

Beam Diameter

<5 mm at aperture

Pulse Data

All pulses < 4 Hz (>0.25 sec)

Divergence (each beam)

<2 mrad

Divergence (total light)

<160 degrees

Laser Power of Each Beam from Aperture*

<5 mW

Laser

Compliance

Statement

This laser product complies with EN/IEC 60825-1 Ed 2, 2007-03, and U.S. FDA/CDRH

FLPPS via the terms of Laser Notice No. 50 dated June 24, 2007. This laser device is

classified 2M/3B. (Class 2M/3B is the international equivalent of U.S. Class IIIa.

) No

maintenance is required to keep this product in compliance with laser

performance

standards.

CLASSIFIED PER IEC 60825-1:2007 Complies with 21 CFR 1040, 10 and 1040, 11 except

for deviations pursuant to Laser Notice No. 50, dated, 2007.

Kinta FX User Manual Rev. 1 Page 13 of 117

Proper Usage

This product is for overhead mounting only. For safety purposes, Chauvet recommends

mounting lighting effect products on steady elevated platforms or sturdy overhead supports

using suitable hanging clamps. In all cases, use safety cables. Obtain appropriate mounting

hardware from your lighting vendor.

International laser safet

y regulations require that laser products must be operated in the fashion

illustrated below, with a minimum of 3 meters (9.8 ft) of vertical separation between the floor and

the lowest laser light. Additionally, 3 meters of horizontal separation is require

d between laser

light and audience or other public spaces.

CAUTION! Use of controls, adjustments, or procedures other than THOSE specified IN

THIS USER MANUAL may result in hazardous radiation exposure.

Page 14 of 117 Kinta FX User Manual Rev. 1

2. INTRODUCTION

Overview

Strobe SMD LEDs

x 16

Sound

Sensitivity

Knob

Power In

Laser Aperture

DMX In/Out

Microphone

Power Out

Fuse Holder

Safety

Loop

Sound

DMX

Slave

Auto

Menu Up Down Enter

Display and Menu Buttons

IR Sensor

Kinta Effect

Lens

13 mm

Mounting

Bracket Hole

Bracket

Adjustment

Knob

Mounting

Bracket

Kinta FX User Manual Rev. 1 Page 15 of 117

Dimensions

Laser Interlock

and Key

If purchased outside of North America, this product will have an interlock and key to prevent the

laser from operating unless the interlock and the key are both

inserted and the key is turned to

the

ON

position.

For the laser to function, you MUST DO BOTH:

• insert the interlock

• insert the key and turn it to the ON position

If both are not performed, the laser WILL NOT turn on!

*For Illustrative Purposes Only

Always turn the key to the OFF position and remove it when leaving this product

unattended to prevent accidents or injuries to third parties.

7.4 in

(187 mm)

10.3 in

(262 mm)

7.4 in

(187 mm)

ON

Insert the

Interlock

Insert AND Turn

the Key to the

ON Position

Page 16 of 117 Kinta FX User Manual Rev. 1

3. SETUP

AC Power

The Kinta FX has an internal auto-r

anging power supply and it can work with an input voltage

range of 100 to 240 VAC, 50/60 Hz.

To determine the product’s power requirements (

circuit breaker, power outlet, and wiring), use

the current value listed on the label affixed to the product’s back panel, or refer to

6. Technical

Specifications in this manual. The listed current rating indicates the product

’s average current

draw under normal conditions.

• Always connect the product to a protected circuit (circuit breaker or fuse). Make sure

the product

has an appropriate electrical ground to avoid the risk of electrocution or

fire.

• To eliminate wear and improve its lifespan, during periods of non-

use completely

disconnect from power via breaker or by unplugging it.

Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the

rheostat or dimmer channel serves only as a 0 to 100% switch.

Fuse

Replacement

Disconnect the product from power.1.

Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.2.

Pry the fuse holder out of the housing.3.

Remove the blown fuse from the holder.4.

Replace with a fuse of the exact same type and rating.5.

Insert the fuse holder back in place and reconnect power.6.

Disconnect the product from power before replacing the fuse.

The product does not ship with a spare fuse; however, the safety cap has room for a spare.

Always replace a blown fuse with a fuse of the same type and rating.

Installed fuse

(held by plastic clip)

Spare fuse holder

(inside safety cap)

Safety cap

Kinta FX User Manual Rev. 1 Page 17 of 117

Power Linking

Power linking is when products are daisy chained together through the power in and power out

plugs, allowing many products to be powered from one wall outlet.

Up to 16 Kinta FX products can be power linked at 120 V, or

up to

31 Kinta FX products can be power linked at 230 V.

The diagram below illustrates the power linking process.

Power Linking

Diagram

Do not power link more than 16 Kinta FX on 120 V.

Do not power link more than 31 Kinta FX on 230 V.

The power linking diagram above shows the North American version of the product only!

Power linking connectors and requirements differ from country to country,

and region to

region.

If using this product anywhere other than North America, consult with the local

Chauvet

distributor.

1

st

Product

2

nd

Product

3

rd

Product

Additional Products

Page 18 of 117 Kinta FX User Manual Rev. 1

Mounting

Before mounting the product, read and follow the safety recommendations indicated in the

Safety Notes.

Use at least one mounting point per product. Make sure the mounting clamp

(such as CLP-15 from Chauvet

) is capable of supporting the weight of the product. For our

Chauvet line of mounting clamps, go to www.chauvetlighting.com/cables-clamps-main.html.

Orientation

The Kinta FX must be mounted in a position that includes planning for safe laser usage. I

n

addition, make sure adequate ventilation is provided around the product.

Rigging

• Before deciding on a location for the product, always make sure there is easy access to the

product for maintenance and programming.

• Make sure that the structure or surface onto which you are mounting the product can support

the product’s weight (see Technical Specifications).

• When mounting the product overhead, always use a safety cable (such as CH-05 from

Chauvet). Mount the product securely to a rigging point, such as an elevated platform or

a

t

russ.

• When rigging the product onto a truss, you should use a mounting clamp of appropriate

weight capacity. The bracket has a 13-mm hole, which is appropriate for this purpose.

• The bracket adjustment knobs allow for directional adjustment when aiming the product t

o

t

he desired angle. Only loosen or tighten the bracket knobs manually. Using tools coul

d

damage the knobs.

Mounting Diagram

Mounting Bracket

Mounting Clamp

Safety Cable

Bracket Adjustment

Knob x2

Kinta FX User Manual Rev. 1 Page 19 of 117

4. OPERATION

This product is not designed for continual use. Make sure there are regular breaks during operation to maximize the life

of your laser. Always disconnect the Kinta FX from power when not in use.

Control Panel

Operation

To access the control panel functions, use the four buttons located underneath the display.

When the product is on, the LED monitor on the rear panel will show the current operating mode

(Standalone or DMX). The product will retain the last saved settings when powered off.

Button

Function

<MENU>

Selects an operation mode or backs out of the current menu option

<UP>

Scrolls up the list of options or selects a higher value

<DOWN>

Scrolls down the list of options or selects a lower value

<ENTER>

Activates a menu option or a selected value

Menu Map

Mode

Programming Steps

Description

DMX

2-CH

d001–d511

Sets DMX personality and address

9-CH

d001–d504

Static Color

C--

C001–C015

Selects Static Color

Auto

P--

P001-007

Selects Auto Program Effect

Speed

S--

S.00–S.99

Speed for Sound Mode and Auto Programs

Sound

SND

SNd1-7

Selects Sound Active Mode Program Effects

Manual Color U--

R001–R255

F.00–F.99

Sets Manual Color choice and Strobe speed (slow to

fast)

G001–G255

B001–B255

W001–W255

IR Function SET

ON

On/Off IR functions

OFF

Auto and Sound Modes Defined

Program

Effect

*1

All effects

*2

Beam and Strobe

*3

Beam and Laser

*4

Laser and Strobe

*5

Beam Only

*6

Strobes Only

*7

Laser Only

Page 20 of 117 Kinta FX User Manual Rev. 1

Static Colors Defined

Program

Effect

C001

Red

C002

Green

C003

Blue

C004

White

C005

Red / Green

C006

Red / Blue

C007

Red / White

C008

Green / Blue

C009

Green / White

C010

Blue / White

C011

Red / Green / Blue

C012

Red / Green / White

C013

Red / Blue / White

C014

Green / Blue / White

C015

Red / Green / Blue / White

Configuration

(Standalone)

Set the product in one of the Standalone modes to control without a DMX controller.

Connect the product to a suitable power outlet.

Never connect a product that is operating in any Standalone mode (Static, Automatic, or

Sound) to a DMX string connected to a DMX controller. Products in Standalone mode may

transmit DMX signals that could interfere with the DMX signals from the controller.

Sound-Active

Mode

To enable the Sound-Active mode, do the following:

Press <MENU> repeatedly until Snd shows on the display. 1.

Press <ENTER> and Snd1–Snd7 will show on the display.2.

Use <UP> or <DOWN> to select the desired Sound-Active program.3.

Press <ENTER>.4.

Turn the music on and a

djust the sound sensitivity knob until the product starts responding to

5.

the beat of the music.

The product will only respond to low frequencies of music (bass and drums).

The product will blackout when in Sound-Active mode after 3 seconds of silence or

noise

below the sensitivity setting.

Automatic Mode

To enable the Automatic mode, follow the instructions below:

Press <MENU> repeatedly until P-- shows on the display.1.

Press <ENTER> and P001–P007 will show on the display.2.

Use <UP> or <DOWN> to select the desired Auto program.3.

Press <ENTER>.4.

Speed

Adjustment

To change the speed of Auto or Sound-Active mode, follow the instructions below:

Press <MENU> repeatedly until S-- shows on the display.1.

Press <ENTER> and S.00–S.99 will show on the display.2.

Use <UP> or <DOWN> to adjust the program speed.3.

Press <ENTER>.4.

Kinta FX User Manual Rev. 1 Page 21 of 117

Configuration

(DMX)

Set the product in DMX mode to control with a DMX controller. The product uses 3-pin DMX

cable.

Connect the product to a suitable power outlet.1.

Connect a DMX cable from the DMX output of the DMX controller to the DMX input socket2.

on the product.

DMX Personality

and Starting

Address

When selecting a DMX starting address, always consider the number of DMX channels used by

the fixture. If you choose a starting address that is too

high, you could restrict the access to

some of the product’s channels.

The Kinta FX uses up to 9 DMX channels in the 9-channel mode, 9-CH, which

means the

highest recommended DMX address for that personality is 504.

The Kinta FX uses 2 DMX channels in the 2-channel mode, 2-CH,

which means the highest

recommended DMX address for that personality is 511.

If you are not familiar with the DMX protocol, download the DMX Primer from

http://www.chauvetlighting.com.

To select the DMX personality and starting address, do the following:

Press <MENU> repeatedly until 2-CH or 9-CH will show in the display1.

Press <ENTER> and d001–d512 shows on the display.2.

Use <UP> or <DOWN> to select the DMX address.3.

Press <ENTER> and d001–d511 (for 2-CH) or d001–d504 (for 9-CH) will show on the4.

display.

The display will continue to blink until the fixture receives a DMX signal.

Master/Slave

Mode

The Master/Slave mode allows a single Kinta FX product (the master) to control the actions of

one or more Kinta FX

products (the slaves) without the need of a DMX controller. The master will

be set to operate in either Automatic or Sound-

Active mode, while the slaves will be set to

operate in Slave mode. Once set and connected, the slave units wil

l operate in unison with the

master.

Configure the products as indicated below.

For every slave:

Set the product's DMX address to d001.1.

• Configure all the slave units before connecting the master to the DMX daisy chain.

• The display on the slaves will continue to blink until the slaves are receiving a DMX

signal from the master.

For the master:

Connect the DMX output of the master to the DMX input of the first slave unit.1.

Set the master unit to operate in either Automatic or Sound-Active mode2.

• Make sure the master is the first unit in the DMX chain.

• Never connect a DMX controller to a DMX chain configured for Master/Slave operation

because the controller may interfere with the signals from the master.

• Do not connect more than 31 slaves to the master.

Page 22 of 117 Kinta FX User Manual Rev. 1

DMX Channel Assignments and Values

9-CH

Channel

Function

Value

Setting

1 Auto Program

000

ó

009

Blackout

010

ó

044

Beams/Laser/Strobe

045

ó

079

Beams/Strobe

080

ó

114

Beams/Laser

115

ó

149

Laser/Strobe

150

ó

184

Beams Only

185

ó

219

Strobe Only

220

ó

255

Laser Only

2 Program Speed

000

ó

250

Auto Program Speed (Slow to fast)

251

ó

255

Sound-Active Sensitivity

3

Effective when CH1 is

000 ó 009:

Manual Color Option

000

ó

005

No function

006

ó

020

Red

021

ó

035

Green

036

ó

050

Blue

051

ó

065

White

066

ó

080

Red / Green

081

ó

095

Red / Blue

096

ó

110

Red / White

111

ó

125

Green / Blue

126

ó

140

Green / White

141

ó

155

Blue / White

156

ó

170

Red / Green / Blue

171

ó

185

Red / Green / White

186

ó

200

Green / Blue / White

201

ó

215

Red / Green / Blue / White

216

ó

230

Automatic 4-color chase

231

ó

255

Automatic 7-color chase

4 Strobe

000

ó

005

No Strobe

006

ó

255

Strobe (slow to fast)

5 Motor

000

No Function

001

ó

127

Indexing

128

ó

255

Speed

Kinta FX User Manual Rev. 1 Page 23 of 117

9-CH

Channel

Function

Value

Setting

6 Pattern Options

000

ó

009

Blackout

010

ó

019

Pattern 1 (slow to fast)

020

ó

029

Pattern 2 (slow to fast)

030

ó

039

Pattern 3 (slow to fast)

040

ó

049

Pattern 4 (slow to fast)

050

ó

059

Pattern 5 (slow to fast)

060

ó

069

Pattern 6 (slow to fast)

070

ó

079

Pattern 7 (slow to fast)

080

ó

089

Pattern 8 (slow to fast)

090

ó

099

Pattern 9 (slow to fast)

100

ó

109

Pattern 10 (slow to fast)

110

ó

119

Pattern 11 (slow to fast)

120

ó

129

Pattern 12 (slow to fast)

130

ó

139

Pattern 13 (slow to fast)

140

ó

149

Pattern 14 (slow to fast)

150

ó

159

Pattern 15 (slow to fast)

160

ó

169

Pattern 16 (slow to fast)

170

ó

179

Pattern 17 (slow to fast)

180

ó

255

Pattern 18 (slow to fast) Solid-ON

7 Laser Colors

000

ó

009

Blackout

010

ó

049

Red

050

ó

089

Green

090

ó

129

Red & Green

130

ó

169

Red on / Green strobe

170

ó

209

Green on / Red strobe

210

ó

255

Red & Green alternating strobe

8 Laser Strobe

000

ó

009

No Function

010

ó

254

Strobe (slow to fast: 0-30 Hz)

255

Sound Strobe

9 Laser Rotation

000

ó

004

Stop

005

ó

127

Rotate Clockwise, fast to slow

128

ó

133

Stop

134

ó

255

Rotate Counter Clockwise, slow to fast

Page 24 of 117 Kinta FX User Manual Rev. 1

02CH

Channel

Function

Value

Setting

1 Auto Program

000

ó

009

Blackout

010

ó

044

Beams/Laser/Strobe

045

ó

079

Beams/Strobe

080

ó

114

Beams/Laser

115

ó

149

Laser/Strobe

150

ó

184

Beams Only

185

ó

219

Strobe Only

220

ó

255

Laser Only

2 Program Speed

000

ó

250

Auto Program Speed (Slow to fast)

251

ó

255

Sound-Active Sensitivity

Page is loading ...

CHAUVET DJ Scorpion Bar RG User manual

This manual is also suitable for

CHAUVET DJ Scorpion Bar RG User manual

in other languages

Related papers

Other documents