Matrix MD-S711 Owner's manual

MD-S711 MEDICAL LEG EXTENSION / LEG CURL

2

ENGLISH

繁體中文

日本語

󼨫󺈼󻪃

TIẾNG VIỆT





3

15

27

39

51

63

75

3

WARNING

DEATH OR SERIOUS INJURY CAN OCCUR ON THIS

EQUIPMENT. FOLLOW THESE PRECAUTIONS TO AVOID

INJURY!

1. Keep children under the age of 14 away from this

strength training equipment. Teenagers must be

supervised at all times while using this

equipment.

2. This equipment is not intended for use by persons

with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge,

unless they have been given supervision or

instruction concerning use of the equipment by a

person responsible for their safety.

3. All warnings and instructions should be read and

proper instruction obtained prior to use. Use this

equipment for its intended purpose ONLY.

4. Inspect the machine before use. DO NOT use

machine if it appears damaged or inoperable.

5. Do not exceed weight capacity of this equipment.

6. Check to see that the selector pin is completely

inserted into the weight stack.

7. NEVER use the machine with the weight stack

pinned in an elevated position.

8. NEVER use dumbbells or other means to

incrementally increase the weight resistance. Only

use the means provided directly from the

manufacturer.

9. Injuries to health may result from incorrect or

excessive training. Cease exercise if you feel faint

or dizzy. Obtain a medical exam before beginning

an exercise program.

10. Keep body, clothing, hair, and ﬁtness accessories

free and clear of all moving parts.

11. Adjustable stops, where provided, must be used

at all times.

12. When adjusting any adjustable mechanism (stop

position, seat position, pad location, range of

motion limiter, pulley carriage, or any other type),

make certain that the adjustable mechanism is fully

engaged prior to use to prevent unintended motion.

13. Manufacturer recommends that this equipment be

secured to the ﬂoor to stabilize and eliminate

rocking or tipping over. Use a licensed contractor.

14. If equipment is NOT secured to ﬂoor: NEVER allow

resistance straps, ropes or other means to be

attached to this equipment, as this may result in

serious injury. NEVER use this equipment for

support during stretching, as this may result in

serious injury.

15. DO NOT REMOVE THIS LABEL. REPLACE IF

DAMAGED OR ILLEGIBLE.

ENGLISH

IMPORTANT SAFETY INFORMATION

It is the sole responsibility of the purchaser

of MATRIX products to instruct all individuals,

whether they are the end user or supervising

personnel on proper usage of the equipment.

It is recommended that all users of MATRIX

exercise equipment be informed of the

following information prior to its use.

Do not use any equipment in any way other than as

designed or intended by the manufacturer. It is imperative

that MATRIX equipment be used properly to avoid injury.

INSTALLATION

1. STABLE AND LEVEL SURFACE: MATRIX exercise equipment

must be installed on a stable base and properly leveled.

2. SECURING EQUIPMENT: Manufacturer recommends

that all stationary MATRIX strength equipment

be secured to the oor to stabilize equipment

and eliminate rocking or tipping over. This

must be performed by a licensed contractor.

3. Under no circumstances should you slide equipment

across the oor due to risk of tipping. Use proper

materials handling techniques and equipment

recommended by OSHA.

All anchor points must be able to withstand

750 lbs. (3.3 kN) pull-out force.

MAINTENANCE

1. DO NOT use any equipment that is damaged and or

has worn or broken parts. Use only replacement parts

supplied by your country’s local MATRIX dealer.

2. MAINTAIN LABELS AND NAMEPLATES: Do not

remove labels for any reason. They contain

important information. If unreadable or missing,

contact your MATRIX dealer for a replacement.

3. MAINTAIN ALL EQUIPMENT: Preventative maintenance

is the key to smooth operating equipment as well

as keeping your liability to a minimum. Equipment

needs to be inspected at regular intervals.

4. Ensure that any person(s) making adjustments

or performing maintenance or repair of any

kind is qualied to do so. MATRIX dealers will

provide service and maintenance training at

our corporate facility upon request.

ADDITIONAL NOTES

This equipment should only be used in supervised areas

where access and control is specically regulated by the

owner. It is up to the owner to determine who is allowed

access to this training equipment. The owner should consider

a user’s: degree of reliability, age, experience, etc.

This training equipment meets industry standards for

stability when used for its intended purpose in accordance

with the instructions provided by the manufacturer.

This equipment is for indoor use only. This training equipment

is a Class S product (designed for use in a commercial

environment such as a tness facility). This training equipment

is in compliance with EN ISO 20957-1 and EN 957-2.

This equipment has been designed for medical/therapeutic use

when used under the supervision of a doctor or clinician.

NOTE

1. Ambient temperature for operating this equipment is 5°C - 40°C

(with NO air-ow), nominal 25°C.

2. Relative Humidity for operating this equipment is 10% - 90% (non-

condensing), nominal 40% (non-condensing).

3. Ambient temperature for shipping and storage this equipment is

from -20°C to 70°C (with NO air-ow).

4. The barometric pressure for operating/storage/transportation of

this equipment should be between 70kPa~106kPa.

5. Relative Humidity for shipping/storage is 10% - 90% (non-

condensing).

6. Please dispose of the scrap according to local laws and regulations.

- Operating Instructions

- JOHNSON INDUSTRIES (SHANGHAI) CO., LTD.

No.4500, Baoqian Rd, Zhuqiao,

Jiading, Shanghai, China

- Emergo Europe

Prinsessegracht 20, 2514 AP The Hague,

The Netherlands

4

PROPER USAGE

1. Do not exceed weight limits of the exercise device.

2. If applicable, set safety stops to appropriate height.

3. If applicable, adjust seat pads, leg pads, foot pads, range of motion

adjustment, or any other type of adjustment mechanisms to a comfortable

start position. Make certain that the adjusting mechanism is fully

engaged to prevent unintentional movement and to avoid injury.

4. Sit on bench (if applicable) and get into appropriate position for exercise.

5. Exercise using no more weight than you can safely lift and control.

6. In a controlled manner, perform exercise.

7. Return weight to its fully-supported start position.

ENGLISH

INTENDED USE

The intended use of the Matrix MD-S711 Medical Leg Extension / Leg Curl is

to create a predetermined, dened physical activity level for the patient. The

physical activity level is generated by the user pushing against a movable leg

bar. The user can either use the back of the ankle to press the leg bar in the

downward direction to perform a Leg Curl exercise, or the user use the front of

the shin to press the leg bar in the upward direction to perform a Leg Extension

exercise. This physical activity level can be done in the controlled environment

of a doctor’s oce or a clinician’s lab. The stress intensity of the physical activity

level can be adjusted by adjusting the amount of resistance applied to the leg bar,

or by the perceived effort as described by the user to the doctor or clinician.

Metabolic System: The medical leg extension / leg curl can be

used to inuence the metabolic system to increase fat-burning,

thereby reducing the size of adipose tissue deposits.

Physical Performance Tests: The dened stress intensity of the

physical activity level can be used to perform physical performance

tests on the strength of the user’s leg muscles.

Recovery: Under a doctor’s care, the medical leg extension / leg curl

can be used to improve muscle strength after surgery or injury.

The handrails and seat of the medical leg extension / leg curl can

be used for additional safety and stabilization of the patient.

Orthopedic Rehabilitation: Under a doctor’s care, the medical leg

extension / leg curl can be used for orthopedic rehabilitation (e.g.

supporting dened/reduced weight to strengthen the legs of a user).

LEG CURL

1

2

LEG EXTENSION

1

2

5

1

Back Pad Recline

Pull handle inward, increase or decrease the angle of the

back pad to comfortable start position, release handle.

Allows the user to adjust the starting angle of the

back pad. The user grasps the innermost handle

and pulls directly inward; lean into the seat until

designed angle is reached, and releases the handle.

1

2 3 4

ENGLISH

4

Ankle Pad Adjustment

Pull pin, adjust pad to desired start position, release pin.

Allows the user to rotate the pad to a

comfortable start position.

2

Back Pad Start Position

Pull handle upward, adjust the back pad to a

comfortable start position, release handle.

Allows the user to adjust the starting position

of the back pad. The user pulls the outermost

handle upwards, chooses comfortable start

position, and then releases handle.

3

Seat Pivot Change

Pull pin, adjust the seat height to correct

exercise start position, release pin.

Allows the user to adjust the seat pad height permitting

the alignment of knees with the pivot point during

exercise. The lower position is for leg curl exercises

and the upper position is for leg extension exercises.

ADJUSTMENT POINTS

6

8

7 5 6

5

Starting Leg Position

Pull pin, adjust pad to desired start position, release pin.

Allows the user to adjust the work arm

to a comfortable start position.

8

0.9 kg / 2 lb Increment Weight (optional)

Remove individual incremental weight pins and insert

above head plate to achieve desired starting weight.

6

Thigh Pad Rotation

Pull pin, rotate thigh pad out, release pin.

Allows the user to swing the thigh pad out away from

the user for easy entrance and exit of the machine.

7

Thigh Pad Release

Depress lever with thumb, raise or

lower pad, release lever.

Allows the user to raise or lower the thigh

pad into a comfortable start position.

ADJUSTMENT POINTS

ENGLISH

7

WARRANTY

For North America, please visit www.matrixtness.com for warranty

information along with warranty exclusions and limitations.

PRODUCT SPECIFICATIONS

Max User Weight 181.4 kg / 400 lbs.

Max Training Weight 94.6 kg / 208 lbs.

Product Weight 219 kg / 483 lbs.

Weight Stack 91 kg / 200 lbs.

Add-On-Weight (optional) 0.9 kg / 2 lbs.

Overall Dimensions

(L x W x H)*

160 x 126 x 167 cm /

63” x 50” x 66”

* Ensure a minimum clearance width of 0.6 meters (24”) for access to and pas-

sage around MATRIX strength equipment. Please note, 0.91 meters (36”) is the

ADA recommended clearance width for individuals in wheelchairs.

MAINTENANCE CHECKLIST

ACTION FREQUENCY

Clean Upholstery

1

Daily

Inspect Cables

2

Daily

Clean Guide Rods Monthly

Inspect Hardware Monthly

Inspect Frame Bi-Annually

Clean Machine As Needed

Clean Grips

1

As Needed

Lubricate Guide Rods

3

As Needed

1

Upholstery & Grips should be cleaned with a mild soap

and water or a non-ammonia based cleaner.

2

Cables should be inspected for cracks or frays and immediately replaced if present.

If excessive slack exists cable should be tightened without lifting the head plate.

3

Guide rods should be lubricated with Teon based lubricant. Apply the

lubricant to a cotton cloth and then apply up and down the guide rods.

ENGLISH

TORQUE VALUES

M10 Bolt (Nyloc Nut & Flowdrill) 77 Nm / 57 ft -lbs

M8 Bolts 25 Nm / 18 ft-lbs

M8 Plastic 15 Nm / 11 ft-lbs

M6 Bolts 15 Nm / 11 ft-lbs

Pad Bolts 10 Nm / 7 ft-lbs

8

TOOLS REQUIRED FOR ASSEMBLY (not included)

3MM L-Shaped Allen Wrench 10MM L-Shaped Allen Wrench

4MM L-Shaped Allen Wrench Phillips Screwdriver

5MM L-Shaped Allen Wrench 8MM Open-End Wrench

6MM L-Shaped Allen Wrench 17MM Open-End Wrench

8MM L-Shaped Allen Wrench Guide Rod Lubrication

If any items are missing please contact your country’s local MATRIX dealer for assistance.

0 mm 10 20 30 40 50 60 70 80 90 100 110 120 130

UNPACKING

Thank you for purchasing a MATRIX Fitness product. It is inspected

before it is packaged. It is shipped in multiple pieces to facilitate the

compact packaging of the machine. Prior to assembly, conrm all the

components by matching them with the exploded diagrams. Carefully

unpack the unit from this box and dispose of the packing materials in

accordance with your local laws. Exercise device must be assembled

by a trained assembly team or be pre-assembled prior to delivery.

CAUTION

To avoid injury to yourself and prevent damage to the frame

components, be sure to have proper assistance removing the frame

pieces from this box. Please be sure to install the equipment on a

stable base, and properly level the machine. Ensure a minimum

clearance width of 0.6 meters (24”) for access to and passage around

MATRIX strength equipment. Please note, 0.91 meters (36”) is the

ADA recommended clearance width for individuals in wheelchairs.

MD-S711 TRAINING AREA

2.18 M

(86”)

1.26 M

(50”)

FREE AREA

0.6 M (2 FT)

WIDE PATH

ENGLISH

9

F BD

D

C

D

E

F

D

B

A

G B H

1

Step 1 Hardware

Description Qty

A

B

C

D

E

F

G

H

Bolt (M10x20L)

Washer (Φ10.2)

Bolt (M10x125L)

Arc Washer (Φ10.5)

Bolt (M10x150L)

Nylock Nut (M10)

Bolt (M10x105L)

Bolt (M10x80L)

2

7

2

12

2

8

2

A

I

Step 2 Hardware

Description Qty

A

I

Bolt (M10x20L)

Washer (Φ10.5xΦ42)

1

Do not fully tighten frame connectors until

assembly is complete. Vibra-Tite 135 Red Gel

or equivalent must be used on all fasteners

that are not assembled with Nylock Nuts.

ENGLISH

pre-installed

10

A

D

B A

A B

D

E

D

F

J

3 4

Step 3 Hardware

Description Qty

J Set Screw (ST4x20L) 1

Step 4 Hardware

Description Qty

A

B

D

E

F

Bolt (M10x20L)

Washer (Φ10.2)

Arc Washer (Φ10.5)

Bolt (M10x150L)

Nylock Nut (M10)

10

8

6

2

ENGLISH

11

I

A

5 6

K L

N M

B

A

Step 2 Hardware

Description Qty

A

B

K

L

M

N

Bolt (M10x20L)

Washer (Φ10.2)

Bolt (M8x15L)

Washer (Φ8.5xΦ60)

Axle (Φ25.0x88)

POM Washer (41.8xΦ20.5)

1

2

ENGLISH

Step 5 Hardware

Description Qty

A

I

Bolt (M10x20L)

Washer (Φ10.5xΦ42)

1

12

P

A

R

Q

O

P

O

B

7 8

Step 7 Hardware

Description Qty

B

O

P

Washer (Φ10.2)

Bolt (M10x25L)

Plug

4

6

2

Step 8 Hardware

Description Qty

A

P

Q

R

Bolt (M10x20L)

Plug

Bolt (M8x25L)

Washer (Φ8.4)

2

ENGLISH

13

S I

ATR

9 10

Q

R

Step 10 Hardware

Description Qty

Q

R

Bolt (M8x25L)

Washer (Φ8.4)

4

ENGLISH

Step 9 Hardware

Description Qty

A

I

R

S

T

Bolt (M10x20L)

Washer (Φ10.5xΦ42)

Washer (Φ8.4)

Wavy Washer (Φ30.5)

Nylock Nut (M8)

1

ASSEMBLY COMPLETE!

14

OPTIONAL ASSEMBLY (SOLD SEPARATELY)

INCREMENTAL WEIGHTS

D

C

B

A

STEP STOOL

ENGLISH

Hardware

Description Qty

A

B

C

D

Plug (pre-installed)

Bolt (M10x20L)

Spring Washer (Φ10.2)

Arc Washer (Φ10.2)

2

15

警告

本器材使用不當可能導致死亡或嚴重人身

傷害。請遵行以下注意事項，避免受傷！

1. 未滿 14 歲的兒童請勿接近本重量訓練

器材。青少年須在成人全程監督下使用

本器材。

2. 本器材不適用於體能、知覺或精神機能

不佳或欠缺經驗及知識的人士；如欲使

用，必須在他人監督下進行，且須由可

負責其人身安全者指導器材用途及使用

方式。

3. 使用前請詳閱所有警告及說明，並接

受正確的指導。請遵循本器材的用途。

4. 使用前請先檢查器材。切勿使用已損

壞或無法操作的器材。

5. 使用本器材時，不可超過承重限制。

6. 檢查確認選擇桿插鞘完全插入重量片

架內。

7. 若重量片架固定於高處，切勿使用本

機器。

8. 切勿利用啞鈴或其他方式增加重量片阻

力。只能按照製造商提供的方式進行。

9.

訓練方式不正確或訓練過度皆有可能損礙

健康。若感覺昏厥或暈眩，請停止訓練。

開始進行訓練課程之前，請接受體檢。

10. 身體、衣物、頭髮及健身配件皆須與所

有活動零件保持距離。

11. 若有可調節限制器，務必全程使用。

12.

當您調整任何可調節裝置 (限制器位置、

座椅位置、踏墊位置、移動範圍限制

裝置、滑輪滑動架或任何其他類型的

裝置)，請務必先確認可調節裝置完

全鎖上再使用，避免裝置突然移動。

13. 製造商建議將本器材固定於地面，

以提高穩定性並避免晃動或傾覆。

請選擇合格承包商。

14. 若未將本器材固定於地面：一律禁止

將抗力帶、抗力繩或其他類似配件綁

附於本器材，否則可能會導致嚴重人身

傷害。請勿以本器材做為伸展運動的支

撐點，否則可能會導致嚴重人身傷害。

15. 請勿撕除此標籤。若標籤破損或模糊不

清，請更換新標籤。

繁體中文

安全重要資訊

MATRIX 產品買主應負責確保已充分教導使用

者或指導人員器材的正確使用方式。

建議所有 MATRIX 健身器材使用者在使用前瞭解下列資訊。

所有器材的使用方式需以製造商的設計原理或原

始用途為主，不可擅自更改。請務必遵行正確的

MATRIX 器材使用方式，以避免造成傷害。

安裝

1. 穩固的平面：MATRIX 健身器材必須安

裝於穩固且平坦的表面上。

2. 固定器材：製造商建議將所有固定式 MATRIX 重

量設備固定於地面，以提高穩定性並避免晃動

或傾覆。必須由合格承包商進行安裝。

3. 為防止設備翻覆，任何情況下都不要在地面上滑動設備。

請使用 OSHA 建議的適當材料處理方法及材料處理設備。

所有固定點的鎖固扭力須達 3.3 kN (750 磅)。

保養

1. 任何器材一旦損壞或零件磨損/破損，一律不得繼續使

用。請使用當地 MATRIX 經銷商所販售的替換零件。

2. 保養標籤和貼標：不可因任何原因撕除標籤。

標籤內含重要資訊。如標籤模糊不清或不見，

請聯絡 MATRIX 經銷商並要求重新張貼。

3. 保養所有器材：預防性保養是保持器材功能正常

及善盡安全責任的關鍵。請定期檢查器材。

4. 確認負責調整或保養/維修器材的人員均為合格人員。MATRIX

可應經銷要求，提供公司器材的維修及保養訓練。

其他注意事項

本器材必須在其所有人可實施具體管控的受監督區域內使用。器材

所有人有權決定哪些人可使用本訓練器材。器材所有人應考量使用

者的：可負責程度、年齡、經驗等等。

如遵行製造商提供之說明並按照其設計用途使用，

本訓練器材符合業界規範的穩定性標準。

本器材僅供室內使用。本訓練器材屬 S 類產

品 (專用於健身房等的商務環境)。本訓練器材符

合 EN ISO 20957-1 及 EN 957-2 的規定。

本設備在醫生或臨床醫生的指導下可作為醫療/治療用途。

注意

1. 本器材的運作環境溫度是 5°C - 40°C (空氣

不流動的情況下)，標稱 25°C。

2. 本器材的運作相對濕度是 10% - 90% (

無冷凝)，標稱 40% (無冷凝)。

3. 本器材的運送及存放環境溫度是 -20°C 到

70°C (空氣不流動的情況下)。

4. 該設備的運行/儲存/運輸的氣壓應在 70kPa~106kPa 之間。

5. 運輸/儲存的相對濕度應在 10% - 90%（無冷凝）之間。

6. 請根據當地法律法規處理廢棄物。

- 操作說明

- JOHNSON INDUSTRIES (SHANGHAI) CO., LTD.

No.4500, Baoqian Rd, Zhuqiao,

Jiading, Shanghai, China

- Emergo Europe

Prinsessegracht 20, 2514 AP The Hague,

The Netherlands

16

正確的使用方式

1. 不可超出訓練器材的重量限制。

2. 若有安全限制器，請將安全限制器調整至適當的高度。

3. 儘可能將座墊、腿墊、腳墊、活動行程調整裝置或任何其他類型的調整裝置，調整到

令您感到舒適的開始位置。確認調整裝置完全鎖緊，避免突然移動及造成傷害。

4. 若有舉重椅，請坐在舉重椅上並調整至適當的訓練位置。

5. 訓練時的重量不可超過您可控制的安全舉重範圍。

6. 請在適度的控制範圍內進行訓練。

7. 將重量片放回到完全支撐穩固的開始位置。

繁體中文

用途

Matrix MD-S711 醫療用腿部伸展訓練機/腿部彎舉機的用途是為病患建立預定、設定

活動量需求。使用者每日的活動量需求可藉由推動腿墊達成。使用者可使用後腳踝將腿

墊往下壓來進行腿部彎舉動作，或者使用前脛將腿墊往上抬來進行腿部伸展動作。可

在診療室或臨床醫師實驗室中的受控環境中完成此活動量需求。藉由調整腳托的阻力

值或透過使用者向醫生或臨床醫生所描述的自覺強度來調整身體活動量需求的強度。

代謝系統：醫療用腿部伸展機/腿部彎舉機可用於影響代謝系統，以增加脂肪燃燒，進而

減少脂肪組織的堆積。

體能測試：設定身體活動量需求的強度，可以用使用者腿部肌肉強度的體能來進行測試。

復健：在醫師指示下，醫療用腿部伸展機/腿部彎舉機可提升術後或傷後的肌肉強度。

醫療用腿部伸展機/腿部彎舉機的扶手與座椅可為病患提供額外的安全性和穩定性。

骨科復健：在醫師指示下，醫療用腿部伸展機/腿部彎舉機可用

於骨科復健 (如增加/減少重量來加強使用者雙腿)。

腿部彎舉機

1

2

腿部伸展訓練機

1

2

17

1

靠背傾斜度

將把手往內拉，增加或減少靠背的角度，達到舒服的開始位置

後，鬆開把手。

讓使用者調整靠背的開始角度。使用者抓住最裡面的把手然

後往內拉；讓背靠椅墊調整到您要的角度，然後鬆開把手。

1

2 3 4

繁體中文

4

腿墊調整

拉起插銷，將腿墊調整到所要開始位置，鬆開插銷。

讓使用者旋轉腿墊到舒服的開始位置。

2

靠背開始位置

將把手往上拉，將靠墊調整到舒服的開始位置，鬆開把手。

讓使用者調整靠背的開始位置。使用者將最外面的把手往上

拉，選擇舒服的開始位置，鬆開把手。

3

座椅高度調整

拉起插銷，將座椅高度調整到正確的開始位置，鬆開插銷。

讓使用者調整椅墊高度，使運動過程中讓膝蓋和關節點對齊。

往下位置是腿部彎舉訓練用，往上位置則是腿部伸展訓練用。

調整位置

18

8

7 5 6

5

腿部開始位置

拉起插銷，將腳踝墊調整到所要開始位置，鬆開插銷。

讓使用者調整機械轉臂到舒服的開始位置。

8

0.9 公斤 / 2 磅增重槓片 (選購)

取出個別的增重槓片插銷，插入上方槓片，以達到所要開始

重量。

6

轉動大腿墊

拉起插銷，將大腿墊往外轉動，鬆開插銷。

讓使用者將大腿墊往外擺動，以便能輕鬆進出機器。

7

大腿墊

用拇指壓下槓桿，抬高或降低大腿墊，鬆開槓桿。

讓使用者抬高或降低大腿墊到舒服的開始位置。

調整位置

繁體中文

19

保固

如果您在北美，請至 www.matrixtness.com 查詢

保固資訊，以及保固的例外和限制條款。

產品規格

使用者體重承載上限

181.4 公斤 / 400 磅

訓練重量承載上限

94.6 公斤 / 208 磅

產品重量

219 公斤 / 483 磅

重量片

91 公斤 / 200 磅

增重槓片 (選購)

0.9 公斤 / 2 磅

總尺寸

(長 x 寬 x 高)*

160 x 126 x 167 公分 /

63 x 50 x 66 英寸

* MATRIX 重量器材周圍務必保留至少 0.6 公尺 (24 英寸) 的寬度，以利使用及通行。

請注意，美國身心障礙法案 (ADA) 建議的輪椅通行寬度是 0.91 公尺 (36 英寸)。

保養檢查清單

措施頻率

清潔墊子

1

每天一次

檢查鋼索

2

每天一次

清潔導桿每月

檢查五金每月

檢查機架每半年一次

清潔器材隨時視需要

清潔握把

1

隨時視需要

潤滑導桿

3

隨時視需要

1

請以溫和的肥皂和清水或不含氨成份的清潔劑清潔墊子與握把。

2

檢查鋼索是否有破裂或磨損情形，若有應立即更換。若鋼索過鬆，應在不抬起上層槓片的

情況下拉緊鋼索。

3

請以鐵弗龍潤滑劑潤滑導桿。以棉布沾取潤滑劑後，再上下擦拭導桿。

繁體中文

扭力值

M10 螺絲 (Nyloc 螺帽和 Flowdrill) 77 Nm / 57 ft-lbs

M8 螺絲 25 Nm / 18 ft-lbs

M8 塑膠 15 Nm / 11 ft-lbs

M6 螺絲 15 Nm / 11 ft-lbs

靠墊螺絲

10 Nm / 7 ft-lbs

20

組裝所需的工具 (非隨附)

3MM L 形內六角扳手 10MM L 形內六角扳手

4MM L 形內六角扳手

十字螺絲起子

5MM L 形內六角扳手 8MM 開口扳手

6MM L 形內六角扳手 17MM 開口扳手

8MM L 形內六角扳手

導桿潤滑劑

如缺少任何物品，請向您所在國家的當地 MATRIX 經銷商求助。

0 mm 10 20 30 40 50 60 70 80 90 100 110 120 130

開箱

感謝您購買 MATRIX Fitness 產品。我們在包裝前已經檢查過產品。為減少器材

包裝體積，本產品拆分多件運送。進行組裝前，請先比對各零組件與圖表內容是

否相符。小心地將器材從本包裝箱取出後，請依照當地法規妥善棄置包裝材料。

運動裝置必須由經過訓練的組裝團隊進行組裝，或者在送貨前已經預先組裝。

注意

為避免受傷及防範破壞機架組件，請務必請他人協助將機架組件從包裝箱內

取出。請務必將器材安裝在穩固的平面上，並使機器保持水平。MATRIX 重

量器材周圍務必保留至少 0.6 公尺 (24 英寸) 的寬度，以利使用及通行。請注

意，美國身心障礙法案 (ADA) 建議的輪椅通行寬度是 0.91 公尺 (36 英寸)。

MD-S711 訓練區域

2.18 公尺

(86 英寸)

1.26 公尺

(50 英寸)

活動區域

0.6 公尺 (2 英尺)

寬幅

繁體中文

Page is loading ...

Matrix MD-S711 Owner's manual

Matrix MD-S711 Owner's manual

in other languages

Related papers