Aruba JH394A Reference guide

HPE FlexFabric 5940 Switch Series

SPB Command Reference

Software version: Release 671x and later

Document version: 6W100-20230822

The information contained herein is subject to change without notice. The only warranties for Hewlett Packard

Enterprise products and services are set forth in the express warranty statements accompanying such

products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett

Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.

Confidential computer software. Valid license from Hewlett Packard Enterprise required for possession, use, or

copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software

Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor’s

standard commercial license.

Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard

Enterprise has no control over and is not responsible for information outside the Hewlett Packard Enterprise

website.

Acknowledgments

Intel®, Itanium®, Pentium®, Intel Inside®, and the Intel Inside logo are trademarks of Intel Corporation in the

United States and other countries.

Microsoft® and Windows® are either registered trademarks or trademarks of Microsoft Corporation in the

United States and/or other countries.

Adobe® and Acrobat® are trademarks of Adobe Systems Incorporated.

Java and Oracle are registered trademarks of Oracle and/or its affiliates.

UNIX® is a registered trademark of The Open Group.

i

Contents

SPBM commands ·························································································· 1

ap-mode ····················································································································································· 1

area-authentication send-only ···················································································································· 1

area-authentication-mode ·························································································································· 2

bandwidth-reference ·································································································································· 3

bridge-priority ············································································································································· 4

b-vlan ························································································································································· 4

circuit-cost ·················································································································································· 5

control-address ·········································································································································· 6

display l2vpn minm connection ·················································································································· 7

display l2vpn minm forwarding ··················································································································· 8

display l2vpn vsi ········································································································································· 9

display spbm agreement-protocol ············································································································ 11

display spbm bridge ································································································································· 13

display spbm b-vlan ································································································································· 14

display spbm bvlan-info ···························································································································· 15

display spbm bvlan-info statistics ············································································································· 16

display spbm common statistics ··············································································································· 17

display spbm ect ······································································································································ 18

display spbm ect-migration ······················································································································ 20

display spbm fast-channel statistics ········································································································· 21

display spbm graceful-restart event-log ··································································································· 22

display spbm graceful-restart status ········································································································ 23

display spbm interface ····························································································································· 25

display spbm lsdb ····································································································································· 26

display spbm multicast-fdb ······················································································································· 30

display spbm multicast-fib ························································································································ 31

display spbm multicast-fib statistics ········································································································· 33

display spbm multicast-pw ······················································································································· 35

display spbm non-stop-routing event-log ································································································· 35

display spbm non-stop-routing status ······································································································ 36

display spbm peer ···································································································································· 37

display spbm summary ···························································································································· 42

display spbm unicast-fdb ·························································································································· 43

display spbm unicast-fib ··························································································································· 44

display spbm unicast-fib statistics ············································································································ 46

display spbm unicast-pw ·························································································································· 47

display spbm unicast-tree ························································································································ 48

ect ···························································································································································· 49

flash-flood ················································································································································· 50

graceful-restart ········································································································································· 51

graceful-restart suppress-sa ···················································································································· 51

graceful-restart t2 ····································································································································· 52

is-name ···················································································································································· 52

l2vpn enable ············································································································································· 53

log-peer-change ······································································································································· 54

multicast replicate-mode ·························································································································· 54

multicast-bvlan enable ····························································································································· 55

non-stop-routing ······································································································································· 56

reset spbm bvlan-info statistics ················································································································ 56

reset spbm database ································································································································ 57

reset spbm graceful-restart event-log ······································································································ 57

reset spbm multicast-fib statistics ············································································································ 58

reset spbm non-stop-routing event-log ···································································································· 58

reset spbm unicast-fib statistics ··············································································································· 59

set-overload ············································································································································· 59

snmp context-name ·································································································································· 60

ii

snmp-agent trap enable spbm ················································································································· 61

spb i-sid ···················································································································································· 62

spbm ························································································································································ 63

spbm authentication send-only ················································································································ 63

spbm authentication-mode ······················································································································· 64

spbm cost ················································································································································· 65

spbm enable ············································································································································· 66

spbm timer hello ······································································································································· 67

spbm timer holding-multiplier ··················································································································· 67

spbm timer lsp ·········································································································································· 68

spsource ··················································································································································· 69

timer lsp-generation ································································································································· 69

timer lsp-max-age ···································································································································· 70

timer lsp-refresh ······································································································································· 71

timer spf ··················································································································································· 72

vsi ····························································································································································· 73

Document conventions and icons ································································ 74

Conventions ····················································································································································· 74

Network topology icons ···································································································································· 75

Support and other resources ······································································· 76

Accessing Hewlett Packard Enterprise Support······························································································· 76

Accessing updates ··········································································································································· 76

Websites ·················································································································································· 77

Customer self repair ································································································································· 77

Remote support ········································································································································ 77

Documentation feedback ························································································································· 77

Index ············································································································ 79

1

SPBM commands

ap-mode

Use ap-mode to configure the agreement protocol (AP) mode.

Use undo ap-mode to restore the default.

Syntax

ap-mode { both | multicast | off }

undo ap-mode

Default

AP is enabled for both unicast and multicast FDB entries.

Views

SPBM view

Predefined user roles

network-admin

Parameters

both: Enables AP for both unicast and multicast FDB entries.

multicast: Enables AP only for multicast FDB entries.

off: Disables AP.

Usage guidelines

AP prevents temporary loops that might occur when the topologies of SPBM neighbors do not

match.

If AP is enabled, ISIS-SPB issues forwarding entries to the FIB tables in the data plane only if AP

declares a topology match after LSDB synchronization is complete.

NOTE:

In this document, "AP" refers to agreement protocol. In other documents, "AP" can also refer to

access points.

Examples

# Enable AP for multicast FDB entries.

<Sysname> system-view

[Sysname] spbm

[Sysname-spbm] ap-mode multicast

area-authentication send-only

Use area-authentication send-only to disable authentication for incoming ISIS-SPB

topology advertisement packets (LSPs, CSNPs, and PSNPs).

Use undo area-authentication send-only to restore the default.

2

Syntax

area-authentication send-only

undo area-authentication send-only

Default

ISIS-SPB authenticates incoming topology advertisement packets if area authentication

(area-authentication-mode) is configured. The device accepts a topology advertisement

packet only if the authentication method and password in the packet match its local authentication

settings.

Views

SPBM view

Predefined user roles

network-admin

Usage guidelines

Before you change area authentication settings for an SPBM network, configure this command to

prevent temporary authentication setting mismatch from causing topology advertisement packets to

be dropped.

For security purposes, restore the default to authenticate incoming topology advertisement packets

after you change area authentication settings across the SPBM network.

This command does not affect outgoing topology advertisement packets. When area authentication

is enabled, outgoing ISIS-SPB topology advertisement packets always contain authentication

information.

Examples

# Disable authentication for incoming ISIS-SPB topology advertisement packets.

<Sysname> system-view

[Sysname] spbm

[Sysname-spbm] area-authentication send-only

Related commands

area-authentication-mode

Use area-authentication-mode to configure area authentication.

Use undo area-authentication-mode to restore the default.

Syntax

area-authentication-mode { md5 | simple } { cipher | plain } string

undo area-authentication-mode

Default

Area authentication is disabled. No area authentication method or password is configured.

Views

SPBM view

Predefined user roles

network-admin

3

Parameters

md5: Specifies MD5 authentication.

simple: Specifies simple authentication.

cipher: Specifies a password in encrypted form.

plain: Specifies a password in plaintext form. For security purposes, the password specified in

plaintext form will be stored in encrypted form.

string: Specifies the password. The plaintext password is a case-sensitive string of 1 to 16

characters. The encrypted password is a case-sensitive string of 33 to 53 characters.

Usage guidelines

ISIS-SPB area authentication guarantees that SPBM nodes learn topology data only from

trustworthy neighbors.

For correct authentication, make sure the authentication method and password are the same across

the SPBM network. ISIS-SPB sends these authentication settings in topology advertisement packets

(LSPs, CSNPs, and PSNPs). The recipients accept a topology advertisement packet only if the

authentication settings in the packet match their local authentication settings.

Example

# Set the area authentication method to simple and the password to 123456 in plain text.

<Sysname> system-view

[Sysname] spbm

[Sysname-spbm] area-authentication-mode simple plain 123456

Related commands

area-authentication send-only

bandwidth-reference

Use bandwidth-reference to set the bandwidth reference for automatic link metric calculation.

Use undo bandwidth-reference to restore the default.

Syntax

bandwidth-reference value

undo bandwidth-reference

Default

The bandwidth reference is 40000 Mbps.

Views

SPBM view

Predefined user roles

network-admin

Parameters

value: Specifies a bandwidth reference in the range of 1 to 2147483648 Mbps.

Usage guidelines

ISIS-SPB automatically calculates a link metric value for an interface if both the global and

interface-specific link metric values are not set.

The following is the calculation formula:

4

Link metric value=(Reference bandwidth/Interface rate)x10

The value range for the link metric value is 1 to 16777214.

Examples

# Set the bandwidth reference to 200 Mbps.

<Sysname> system-view

[Sysname] spbm

[Sysname-spbm] bandwidth-reference 200

Related commands

circuit-cost

spbm cost

bridge-priority

Use bridge-priority to set the SPBM bridge priority.

Use undo bridge-priority to restore the default.

Syntax

bridge-priority priority

undo bridge-priority

Default

The SPBM bridge priority is 32768.

Views

SPBM view

Predefined user roles

network-admin

Parameters

priority: Specifies a bridge priority. It must be a multiple of 4096 in the range of 0 to 61440. For

example, the bridge priority can be 0, 4096, or 8192. A lower value represents higher priority.

Usage guidelines

In conjunction with the system ID, the SPBM bridge priority forms the SPBM bridge ID. The SPBM

bridge ID is a tie-breaker used in the ECT algorithms for choosing shortest paths.

Examples

# Set the bridge priority to 4096.

<Sysname> system-view

[Sysname] spbm

[Sysname-spbm] bridge-priority 4096

b-vlan

Use b-vlan to assign a B-VLAN to an SPB VSI.

Use undo b-vlan to restore the default.

Syntax

b-vlan vlan-id

5

undo b-vlan

Default

No SPB VSI is assigned a B-VLAN.

Views

SPB I-SID view

Predefined user roles

network-admin

Parameters

vlan-id: Specifies a B-VLAN ID in the range of 1 to 4094.

Usage guidelines

You can assign only one B-VLAN to an SPBM VSI, but different SPBM VSIs can use the same

B-VLAN.

For an SPBM VSI, you must specify the same I-SID and B-VLAN across all BEBs and BCBs.

Examples

# Assign B-VLAN 100 to I-SID 256.

<Sysname> system-view

[Sysname] vsi vpn1

[Sysname-vsi-vpn1] spb i-sid 256

[Sysname-vsi-vpn1-256] b-vlan 100

circuit-cost

Use circuit-cost to set a global SPBM link metric value.

Use undo circuit-cost to restore the default.

Syntax

circuit-cost cost-value

undo circuit-cost

Default

No global SPBM link metric value is set.

Views

SPBM view

Predefined user roles

network-admin

Parameters

cost-value: Specifies a link metric value in the range of 1 to 16777215.

Usage guidelines

To assign a link metric value to an interface, use one of the following methods:

•

Set an interface-specific value in interface view.

•

Set a global value in SPBM view. This global value applies to all SPBM-enabled interfaces.

•

Set a bandwidth reference for the system to calculate a value automatically for the interface.

6

The system chooses a link metric value for an interface in order of interface-specific value, global

value, and autocalculated value.

Examples

# Set the global SPBM link metric value to 11.

<Sysname> system-view

[Sysname] spbm

[Sysname-spbm] circuit-cost 11

Related commands

bandwidth-reference

spbm cost

control-address

Use control-address to configure the control MAC address for ISIS-SPB.

Use undo control-address to restore the default.

Syntax

control-address { all-cb | all-is | all-l1-is | all-l2-is | all-pb }

undo control-address

Default

The control MAC address for ISIS-SPB is 0180-C200-002E (all-pb).

Views

SPBM view

Predefined user roles

network-admin

Parameters

all-cb: Sets the control MAC address for ISIS-SPB to 0180-C200-002F.

all-is: Sets the control MAC address for ISIS-SPB to 0900-2B00-0005.

all-l1-is: Sets the control MAC address for ISIS-SPB to 0180-C200-0014.

all-l2-is: Sets the control MAC address to 0180-C200-0015.

all-pb: Sets the control MAC address to 0180-C200-002E.

Usage guidelines

ISIS-SPB uses a control MAC address for ISIS-SPB peer-to-peer communication. The control MAC

specifies the destination MAC address for ISIS-SPB protocol frames.

Vendors might use different control MAC addresses. You can change the ISIS-SPB control MAC for

interoperability in a multivendor network.

Examples

# Set the control MAC address for ISIS-SPB to 0900-2B00-0005 (all-is).

<Sysname> system-view

[Sysname] spbm

[Sysname-spbm] control-address all-is

7

display l2vpn minm connection

Use display l2vpn minm connection to display MAC-in-MAC connections.

Syntax

display l2vpn minm connection [ vsi vsi-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vsi vsi-name: Specifies a VSI name, a case-sensitive string of 1 to 31 characters. If you do not

specify a VSI, the command displays MAC-in-MAC connections for all VSIs.

Examples

# Display MAC-in-MAC connections for all VSIs.

<Sysname> display l2vpn minm connection

Total number of MinM connections: 6

Types: MC - multicast, UC - unicast

VSI name: 1

Link ID I-SID BMAC BVLAN Owner Type Interface

64 10001 9999-8888-7777 1234 SPB UC XGE1/0/1

65 10001 9999-8988-7777 1234 SPB UC XGE1/0/1

- 10001 0011-2222-3333 1234 SPB MC XGE1/0/1

VSI name: 2

Link ID I-SID BMAC BVLAN Owner Type Interface

68 10002 9999-8888-7777 1234 SPB UC XGE1/0/1

69 10002 9999-8988-7777 1234 SPB UC XGE1/0/1

- 10002 9999-9088-7777 1234 SPB MC XGE1/0/1

XGE1/0/2

Table 1 Command output

Field

Description

Link ID Link ID of the MAC-in-MAC connection.

I-SID Backbone service instance identifier.

BMAC Backbone MAC address.

BVLAN Backbone VLAN.

Owner Entry source:

• PBB—The connection is set up by PBB.

• SPB—The connection is set up by SPBM.

8

Field

Description

Type Type of the MAC-in-MAC connection:

• MC—The connection is for multicast.

• UC—The connection is for unicast.

Interface Outgoing interface.

display l2vpn minm forwarding

Use display l2vpn minm forwarding to display MAC-in-MAC forwarding entries.

Syntax

display l2vpn minm forwarding [ vsi vsi-name ] [ slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vsi vsi-name: Specifies a VSI name, a case-sensitive string of 1 to 31 characters. If you do not

specify a VSI, the command displays MAC-in-MAC forwarding entries for all VSIs.

slot slot-number: Specifies an IRF member device. The slot-number argument represents

its IRF member ID. If you do not specify a member device, the command displays MAC-in-MAC

forwarding entries on the master device.

Examples

# Display all MAC-in-MAC forwarding entries.

<Sysname> display l2vpn minm forwarding

Total number of MinM connections: 6

Types: MC - multicast, UC - unicast

Status Flag: * - inactive

VSI name: 1

Link ID I-SID BMAC BVLAN Owner Type Interface

64 10001 9999-8888-7777 1234 SPB UC XGE1/0/1

65 10001 9999-8988-7777 1234 SPB UC XGE1/0/1

- 10001 0011-2222-3333 1234 SPB MC XGE1/0/1

VSI name: 2

Link ID I-SID BMAC BVLAN Owner Type Interface

68 10002 9999-8888-7777 1234 SPB UC XGE1/0/1

69 10002 9999-8988-7777 1234 SPB UC XGE1/0/1

- 10002 9999-9088-7777 1234 SPB MC XGE1/0/1

XGE1/0/2

9

Table 2 Command output

Field

Description

Link ID Link ID of the MAC-in-MAC connection.

I-SID Backbone service instance identifier.

BMAC Backbone MAC address.

BVLAN Backbone VLAN.

Owner Entry source:

• PBB—The connection is set up by PBB.

•

SPB

—The connection is set up by SPBM.

Type Type of the MAC-in-MAC connection:

• MC—The connection is for multicast.

• UC—The connection is for unicast.

Interface Outgoing interface.

If the entry does not take effect, an asterisk (*) is displayed next to the outgoing

interface.

display l2vpn vsi

Use display l2vpn vsi to display VSI information.

Syntax

display l2vpn vsi [ name vsi-name ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

name vsi-name: Specifies a VSI name, a case-sensitive string of 1 to 31 characters. If you do not

specify a VSI, the command displays information about all VSIs.

verbose: Displays detailed VSI information. If you do not specify this keyword, the command

displays brief VSI information.

Examples

# Display detailed information about all VSIs.

<Sysname> display l2vpn vsi verbose

VSI Name: 0

VSI Index : 0

VSI State : Up

MTU : 1500

Bandwidth : Unlimited

Broadcast Restrain : Unlimited

Multicast Restrain : Unlimited

Unknown Unicast Restrain: Unlimited

10

MAC Learning : Enabled

MAC Table Limit : -

MAC Learning rate : -

Drop Unknown : -

SPB I-SID : 10000

Flooding : Enabled

Statistics : Disabled

VXLAN ID : -

VSI Name: 1

VSI Index : 1

VSI State : Up

MTU : 1500

Bandwidth : Unlimited

Broadcast Restrain : Unlimited

Multicast Restrain : Unlimited

Unknown Unicast Restrain: Unlimited

MAC Learning : Enabled

MAC Table Limit : -

MAC Learning rate : -

Drop Unknown : -

SPB I-SID : 10001

Flooding : Enabled

Statistics : Disabled

VXLAN ID : -

SPB Connections:

BMAC BVLAN Link ID Type

9999-8888-7777 1234 64 Unicast

9999-8988-7777 1234 65 Unicast

ACs:

AC Link ID State Type

BAGG1 srv1 0 Down Manual

Table 3 Command output

Field

Description

VSI Description VSI description. This field is displayed only if you have configured a

description for the VSI.

VSI State

VSI state:

• Up—The VSI is up.

• Down—The VSI is down.

• Administratively down—The VSI has been manually shut down with

the

shutdown

command.

MTU MTU for the VSI.

Bandwidth This field is not supported in the current software version.

Bandwidth limit in kbps. If no bandwidth limit is set for the VSI, Unlimited is

displayed.

Broadcast Restrain Broadcast restraint bandwidth (in kbps).

Multicast Restrain Multicast restraint bandwidth (in kbps).

11

Field

Description

Unknown Unicast Restrain Unknown unicast restraint bandwidth (in kbps).

MAC Learning State of the MAC learning feature:

• Enabled—The feature is enabled.

• Disabled—The feature is disabled.

MAC Table Limit

This field is not supported in the current software version.

Maximum number of MAC address entries on the VSI.

If the value is set to Unlimited, there is no limit on the number of MAC

address entries.

MAC Learning rate This field is not supported in the current software version.

MAC entry learning rate of the VSI.

Drop Unknown

This field is not supported in the current software version.

Action on frames that have unknown source MAC addresses after the

maximum number of MAC entries is reached:

• Enabled—Drops these packets.

• Disabled—Forwards these packets.

Flooding State of the VSI's flooding feature:

• Enabled—Flooding is enabled on the VSI.

• Disabled—Flooding is disabled on the VSI.

Statistics Packet statistics state:

• Enabled—The packet statistics feature is enabled for the VSI.

•

Disabled

—The packet statistics feature is disabled for the VSI.

VXLAN ID VXLAN ID

. This field is not supported in SPBM and always displays a hyphen

(-).

Type Entry type:

• Multicast—The entry is used for multicast forwarding.

•

Unicast

—The entry is used for unicast forwarding.

ACs Attachment circuits that are bound to the VSI.

AC Represents an attachment circuit. This field consists of a Layer 2 interface

name and an Ethernet service instance name. For example, XGE1/0/1 srv1.

Link ID Link ID automatically assigned to the AC or PW in the VSI.

State AC state:

• Up.

• Down.

Type Type and traffic match mode of the Ethernet service instance. Manual

indicates a static Ethernet service instance in VLAN-based traffic match

mode.

display spbm agreement-protocol

Use display spbm agreement-protocol to display AP information about an ECT algorithm

on an interface.

Syntax

display spbm agreement-protocol status interface interface-type

interface-number ect ect-number [ standby slot slot-number ]

12

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface interface-type interface-number: Specifies an interface by its type and

number.

ect ect-number: Specifies an ECT algorithm index in the range of 1 to 16.

standby: Specifies the standby process. If you do not specify this keyword, the command displays

AP information about an ECT algorithm on a per-interface basis for the master process.

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify a

member device, this command displays AP information about an ECT algorithm on a per-interface

basis on the master device.

Examples

# Display AP information about ECT algorithm 1 on Ten-GigabitEthernet 1/0/1.

<Sysname> display spbm agreement-protocol status interface ten-gigabitethernet 1/0/1 ect

1

Port AP information:

TxDigest : 00000000000000000000000000003f1f5e5270ce

RxDigest : 00000000000000000000000000003f1f5e5270ce

NBRAPMode: Both

TxAN : 1 TxDAN : 0

RxAN : 0 RxDAN : 0

TxValid : No RxValid : No

MisOrder : No TopoAgree: Yes

CalcEnd : Yes AgreeSend: Normal

Port SPT AP information:

SystemID : 0011.2200.0001

Role : ROOT SelectedRole: ROOT

PSTState : 2 ReRoot : No

Agree : Yes Agreed : Yes

Sync : No Synced : Yes

Forward : Yes Forwarding : Yes

Port SPT AP information:

SystemID : 0011.2200.0101

Role : DESI SelectedRole: DESI

PSTState : 2 ReRoot : No

Agree : Yes Agreed : Yes

Sync : No Synced : Yes

Forward : Yes Forwarding : Yes

13

Table 4 Command output

Field

Description

TxDigest Local agreement digest.

RxDigest Agreement digest of the neighbor.

NBRAPMode

AP mode of the neighbor:

• Both—Performs AP check for both unicast and multicast FDB entries.

• Multicast—Performs AP check only for multicast FDB entries.

• Off—AP mode is disabled.

TxAN Local agreement number.

TxDAN Local discarded agreement number.

RxAN Neighbor's agreement number.

RxDAN Neighbor's discarded agreement number.

TxValid Validity of the local digest.

RxValid Validity of the neighbor's digest.

MisOrder Whether or not the message is out of order.

TopoAgree Whether or not the topologies of the two sides match.

CalcEnd Whether or not topology calculation has been finished.

AgreeSend Digest transmit mode:

• Normal—The agreement digest was sent at the normal speed.

• Fast—The agreement digest was fast flooded.

SystemID System ID for the root of the SPT that contains the port.

Role

Current port role:

• ROOT—Root port.

• ALTE—Alternate port.

• DESI—Designated port.

SelectedRole

Newly computed role for the port:

• ROOT—Root port.

• ALTE—Alternate port.

• DESI—Designated port.

PSTState PST state of the port, including discarding, learning, and forwarding.

ReRoot Whether or not a reroot is required for the port.

Agree Whether or not the port sends the Agreement flag.

Agreed Whether or not an Agreement has been received.

Sync Whether or not a port state synchronization is required on the port.

Synced Port state synchronization state.

Forward Whether or not the port is to be placed in forwarding state.

Forwarding Whether or not the port is in forwarding state.

display spbm bridge

Use display spbm bridge to display SPBM bridge information.

14

Syntax

display spbm bridge

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display SPBM bridge information.

<Sysname> display spbm bridge

System ID Priority SPSource ID Host name

5555.1111.1111 32768 128 SPB-1

Table 5 Command output

Field

Description

Priority Bridge priority.

SPSource ID Shortest path source identifier.

Host name Hostname. If a hostname is not configured, this field displays the system ID.

display spbm b-vlan

Use display spbm b-vlan to display ECT algorithm information about B-VLANs.

Syntax

display spbm b-vlan [ vlan-id ] [ standby slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vlan-id: Specifies a B-VLAN ID in the range of 1 to 4094. If you do not specify a B-VLAN ID, the

command displays ECT algorithm information for all B-VLANs.

standby: Specifies the standby process. If you do not specify this keyword, the command displays

ECT algorithm information about B-VLANs for the master process.

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify a

member device, this command displays ECT algorithm information about B-VLANs on the master

device.

Examples

# Display ECT algorithm information about all B-VLANs.

<Sysname> display spbm b-vlan

B-VLAN 1:

Mode: SPBM

15

Local use: Yes Remote use: No

ECT-Index: 1 Algorithm: 00-80-c2-01 Mask: 0x00

I-SID list: 300-302, 305, 309

B-VLAN 2:

Mode: SPBM

Local use: Yes Remote use: No

ECT-Index: 1 Algorithm: 00-80-c2-01 Mask: 0x00

I-SID list: 400-402, 404

Table 6 Command output

Field

Description

Mode System operating mode. This field displays

SPBM

for an SPBM-enabled device.

Local use Availability of the B-VLAN for transmitting traffic at the local end:

• Yes—The B-VLAN can transmit traffic.

• No—The B-VLAN cannot transmit traffic.

Remote use Availability of the B-VLAN for transmitting traffic at the remote end:

• Yes—The B-VLAN can transmit traffic.

• No—The B-VLAN cannot transmit traffic.

ECT-Index ECT algorithm index.

Algorithm ECT algorithm content.

Mask ECT algorithm mask.

I-SID list I-SIDs mapped to the B-VLAN on the local device.

This field displays N/A if no I-SIDs are mapped to the B-VLAN.

display spbm bvlan-info

Use display spbm bvlan-info to display SPBM B-VLAN information.

Syntax

display spbm bvlan-info [ slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

slot slot-number: Specifies an IRF member device. The slot-number argument represents

its IRF member ID. If you do not specify a member device, the command displays B-VLAN

information for all member devices.

Examples

# Display SPBM B-VLAN information.

<Sysname> display spbm bvlan-info

Epoch: 0x1

Config B-VLAN list:

1-7, 20

16

Driver B-VLAN list:

1

Table 7 Command output

Field

Description

Epoch Number of SPBM process reinitiations.

Config B-VLAN list B-VLANs mapped to MSTI 4092 at the CLI.

Driver B-VLAN list B-VLANs issued to the driver.

display spbm bvlan-info statistics

Use display spbm bvlan-info statistics to display SPBM B-VLAN statistics.

Syntax

display spbm bvlan-info statistics [ slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

slot slot-number: Specifies an IRF member device. The slot-number argument represents

its IRF member ID. If you do not specify a member device, the command displays B-VLAN statistics

for all member devices.

Examples

# Display all SPBM B-VLAN statistics.

<Sysname> display spbm bvlan-info statistics

SPBM B-VLAN basic statistics:

RefreshMsg : 1 AgeNumber : 0

DrvAddNumber : 1 DrvDeleteNumber : 0

SPBM B-VLAN error statistics:

BVLANMsgError : 0 BVLANCreatFail : 0

DrvEnableFail : 0 DrvDisableFail : 0

AllocBVLANFail : 0

Table 8 Command output

Field

Description

RefreshMsg Number of B-VLAN refresh messages.

AgeNumber Number of B-VLAN expirations.

DrvAddNumber Number of messages sent to the driver for adding B-VLANs.

DrvDeleteNumber Number of messages sent to the driver for deleting B-VLANs.

BVLANMsgError Number of B-VLAN error messages received by SPBM.

BVLANCreatFail Number of memory allocation failures for B-VLAN creation.

Page is loading ...

Aruba JH394A Reference guide

This manual is also suitable for

Aruba JH394A Reference guide

Related papers

Other documents