Graco 24N808 Specification

Brand: Graco

Model: 24N808

Category: Garden tools

Type: Specification

This manual is also suitable for

313034H

Operation

LTS 15, LTS 17, ProLTS 17 and ProLTS 19

Airless Sprayers

- For portable spray applications of architectural paints and coatings. For professional use only-

Models 257060, 257065, 24N906, 24N808

3000 psi (21 MPa, 207 bar) Maximum Working Pressure

See page 2 for model and series information including

dispense rate, recommended hose length, guns, and

maximum working pressure.

IMPORTANT SAFETY INSTRUCTIONS.

Read all warnings and instructions in this

manual. Save these instructions.

LTS 15 & LTS 17 Models ONLY: Use water-based or min-

eral spirit-type materials only. Do not use materials having

flash points lower than 70° F (21° C). This includes, but is

not limited to, acetone, xylene, toluene, or naptha. For more

information about your material, request MSDS from distrib-

utor or retailer.

Related Manual:

313036 - Repair

ti11304a

Model: 257060

AGNUM LTS 15

MAGNUM LTS 17

Model: 257065

AGNUM PROLTS 17

Model: 24N906

AGNUM PROLTS 19

Model: 24N808

ti11305a

ti9369b

ti9368b

Specifications

2 313034H

Specifications

This equipment is not intended for use with flammable or combustible materials used in places such as cabinet shops

or other “factory”, or fixed locations. If you intend to use this equipment in this type of application, you must comply

with NFPA 33 and OSHA requirements for the use of flammable and combustible materials.

Model Name Series

Dispense

Rate gpm

(lpm)

Hose Length and

Diameter

Gun

Model

Maximum Working

Pressure

PSI MPa bar

AGNUM

LTS 15

0.27 gpm

(1.02 lpm)

1/4 in. x 25 ft

(6.4 mm x 7.5 m)

SG2 3000 21 207

AGNUM

LTS 17

0.31 gpm

(1.17 lpm)

1/4 in. x 25 ft

(6.4 mm x 7.5 m)

SG2 3000 21 207

AGNUM

ProLTS 17

0.34 gpm

(1.29 lpm)

1/4 in. X 50 ft

(6.4 mm x 15 m)

SG3 3000 21 207

AGNUM

ProLTS 19

0.38 gpm

(1.44 lpm)

1/4 in. X 50 ft

(6.4 mm x 15 m)

SG3 3000 21 207

Warnings

313034H 3

Warnings

The following warnings are for the setup, use, grounding, maintenance and repair of this equipment. The exclamation

point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risks. Refer back to

these warnings. Additional, product-specific warnings may be found throughout the body of this manual where appli-

cable.

WARNINGWARNINGWARNING

WARNING

GROUNDING

This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of

electric shock by providing an escape wire for the electric current. This product is equipped with a cord

having a grounding wire with an appropriate grounding plug. The plug must be plugged into an outlet that

is properly installed and grounded in accordance with all local codes and ordinances.

• Improper installation of the grounding plug is able to result in a risk of electric shock.

• When repair or replacement of the cord or plug is required, do not connect the grounding wire to either

flat blade terminal.

• The wire with insulation having an outer surface that is green with or without yellow stripes is the

grounding wire.

• Check with a qualified electrician or serviceman when the grounding instructions are not completely

understood, or when in doubt as to whether the product is properly grounded.

• Do not modify the plug provided; if it does not fit the outlet, have the proper outlet installed by a quali-

fied electrician.

• This product is for use on a nominal 120V circuit and has a grounding plug similar to the plug illustrated

in the figure below.

• Only connect the product to an outlet having the same configuration as the plug.

• Do not use an adapter with this product.

Extension Cords:

• Use only a 3-wire extension cord that has a 3-blade grounding plug and a 3-slot receptacle that

accepts the plug on the product.

• Make sure your extension cord is not damaged. If an extension cord is necessary, use 12 AWG (2.5

) minimum to carry the current that the product draws. An undersized cord results in a drop in line

voltage and loss of power and overheating.

ti9164a

Warnings

4 313034H

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent

fire and explosion:

• Do not spray flammable or combustible materials near an open flame or sources of ignition such as cig-

arettes, motors, and electrical equipment. For LTS 15 and LTS 17 models: only use water-based or

mineral spirit-type materials with a flash point greater than 70

° F (21° C).

• Paint or solvent flowing through the equipment is able to result in static electricity. Static electricity cre-

ates a risk of fire or explosion in the presence of paint or solvent fumes. All parts of the spray system,

including the pump, hose assembly, spray gun, and objects in and around the spray area shall be prop-

erly grounded to protect against static discharge and sparks. Use Graco conductive or grounded

high-pressure airless paint sprayer hoses.

• Verify that all containers and collection systems are grounded to prevent static discharge.

• Connect to a grounded outlet and use grounded extensions cords. Do not use a 3-to-2 adapter.

• Do not use a paint or a solvent containing halogenated hydrocarbons.

• Keep spray area well-ventilated. Keep a good supply of fresh air moving through the area. Keep pump

assembly in a well ventilated area. Do not spray pump assembly.

• Do not smoke in the spray area.

• Do not operate light switches, engines, or similar spark producing products in the spray area.

• Keep area clean and free of paint or solvent containers, rags, and other flammable materials.

• Know the contents of the paints and solvents being sprayed. Read all Material Safety Data Sheets

(MSDS) and container labels provided with the paints and solvents. Follow the paint and solvents man-

ufacturer’s safety instructions.

• Fire extinguisher equipment shall be present and working.

• Sprayer generates sparks. When flammable liquid is used in or near the sprayer or for flushing or

cleaning, keep sprayer at least 20 feet (6 m) away from explosive vapors.

SKIN INJECTION HAZARD

High-pressure spray is able to inject toxins into the body and cause serious bodily injury. In the event that

injection occurs, get immediate surgical treatment.

• Do not aim the gun at, or spray any person or animal.

• Keep hands and other body parts away from the discharge. For example, do not try to stop leaks with

any part of the body.

• Always use the nozzle tip guard. Do not spray without nozzle tip guard in place.

• Use Graco nozzle tips.

• Use caution when cleaning and changing nozzle tips. In the case where the nozzle tip clogs while

spraying, follow the Pressure Relief Procedure for turning off the unit and relieving the pressure

before removing the nozzle tip to clean.

• Do not leave the unit energized or under pressure while unattended. When the unit is not in use, turn

off the unit and follow the Pressure Relief Procedure for turning off the unit.

• Check hoses and parts for signs of damage. Replace any damaged hoses or parts.

• This system is capable of producing 3000 psi. Use Graco replacement parts or accessories that are

rated a minimum of 3000 psi.

• Always engage the trigger lock when not spraying. Verify the trigger lock is functioning properly.

• Verify that all connections are secure before operating the unit.

• Know how to stop the unit and bleed pressure quickly. Be thoroughly familiar with the controls.

WARNINGWARNINGWARNING

WARNING

Warnings

313034H 5

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system com-

ponent. See Technical Data in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all

equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about

your material, request MSDS from distributor or retailer.

• Do not leave the work area while equipment is energized or under pressure.

• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufac-

turer’s replacement parts only.

• Do not alter or modify equipment. Alterations or modifications may void agency approvals and create

safety hazards.

• Make sure all equipment is rated and approved for the environment in which you are using it.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

ELECTRIC SHOCK HAZARD

This equipment must be grounded. Improper grounding, setup, or usage of the system can cause electric

shock.

• Turn off and disconnect power cord before servicing equipment.

• Connect only to grounded electrical outlets.

• Use only 3-wire extension cords.

• Ensure ground prongs are intact on power and extension cords.

• Do not expose to rain. Store indoors

PRESSURIZED ALUMINUM PARTS HAZARD

Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious chemical

reaction and equipment rupture. Failure to follow this warning can result in death, serious injury, or prop-

erty damage.

• Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids

containing such solvents.

• Many other fluids may contain chemicals that can react with aluminum. Contact your material supplier

for compatibility.

BURN HAZARD

Equipment surfaces and fluid that’s heated can become very hot during operation. To avoid severe burns:

• Do not touch hot fluid or equipment.

MOVING PARTS HAZARD

Moving parts can pinch or amputate fingers and other body parts.

• Keep clear of moving parts.

• Do not operate equipment with protective guards or covers removed.

• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,

follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.

WARNINGWARNINGWARNING

WARNING

Warnings

6 313034H

TOXIC FLUID OR FUMES HAZARD

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swal-

lowed.

• Read MSDS’s to know the specific hazards of the fluids you are using.

• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

PERSONAL PROTECTIVE EQUIPMENT

Wear appropriate protective equipment when in the work area to help prevent serious injury, including eye

injury, hearing loss, inhalation of toxic fumes, and burns. This protective equipment includes but is not lim-

ited to:

• Protective eyewear, and hearing protection.

• Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.

WARNINGWARNINGWARNING

WARNING

Installation

313034H 7

Installation

Grounding and Electric

Requirements

Sprayer must be grounded. Grounding reduces the risk

of static and electric shock by providing an escape wire

for electrical current due to static build up or in the event

of a short circuit.

• The 120 Vac sprayers

require a 120 Vac, 60

Hz, 15A circuit with a

grounding receptacle.

• Never use an outlet

that is not grounded

or an adapter.

• Do not use the

sprayer if the electrical cord has

a damaged ground prong.

• Only use an extension cord with

an undamaged 3-prong plug.

Recommended extension cords

for use with this sprayer:

• 50 ft (15.0 m) 14 AWG (2.1 mm

)

• 100 ft (30.0 m) 12 AWG (3.3 mm

)

Spray gun

: ground through connection to a properly

grounded fluid hose and pump.

NOTE: Smaller gauge or longer extension cords may

reduce sprayer performance.

Fluid supply container

: follow local code.

Solvent pails used when flushing

: follow local code.

Use only conductive metal pails, placed on a grounded

surface such as concrete. Do not place the pail on a

nonconductive surface, such as paper or cardboard,

which interrupts grounding continuity.

Grounding the metal pail

: connect a ground wire to the

pail by clamping one end to pail and other end to ground

such as a water pipe.

Maintaining grounding continu-

ity when flushing or relieving

pressure: hold metal part of the

spray gun firmly to the side of a

grounded metal pail, then trigger

the gun.

Thermal Overload

Motor has a thermal overload switch to shut itself down

if overheated. If unit overheats, allow approximately 45

minutes for unit to cool. Once cool, switch will close and

unit will restart.

ti5573a

ti5572a

To reduce risk of injury from motor starting unexpect-

edly when it cools, always turn power switch OFF if

motor shuts down.

ti9207a

Component Identification

8 313034H

Component Identification

Airless spray gun

Dispenses fluid.

Power switch

Turns sprayer ON and OFF.

Pressure control knob

Increases (clockwise) and decreases (counter-clockwise) fluid pressure in

pump, hose, and spray gun.

Setting Indicator

To select function, align symbol on pressure control knob with setting

indicator, page 10.

Pump fluid outlet fitting

Threaded connection for paint hose.

InstaClean

™

fluid filter

(ProLTS Sprayers only)

• Filters fluid coming out of pump to reduce tip plugging and improve

finish.

• Self cleans only during pressure relief.

Power-Piston

™

Pump (behind

Easy Access door, not shown)

(ProLTS Sprayers only)

Pumps and pressurizes fluid and delivers it to paint hose.

Easy Access door

(ProLTS Sprayers only)

Easy Access door permits quick access to outlet valve. To remove door, insert

flat blade of screwdriver into slot on the bottom of the door (as shown on page,

7).

Suction tube

Draws fluid from paint pail into pump.

Prime tube (with diffuser)

Drains fluid in system during priming and pressure relief.

Prime/Spray valve

• In PRIME position (pointing down) directs fluid to prime tube.

• In SPRAY position (pointing forward) directs pressurized fluid to paint

hose.

• Automatically relieves system pressure in overpressure situations.

Inlet screen

Prevents debris from entering pump.

Paint hose

Transports high-pressure fluid from pump to spray gun.

Tip guard

Reduces risk of fluid injection injury.

Reversible spray tip

• Atomizes fluid being sprayed, forms spray pattern and controls fluid flow

according to hole size.

• Reverse unclogs plugged tips without disassembly.

Gun trigger safety lever (page

10)

Prevents accidental triggering of spray gun.

Gun fluid inlet fitting

Threaded connection for paint hose.

Power Flush attachment

Connects garden hose to suction tube for power flushing water-base

fluids.

Gun fluid filter

Filters fluid entering spray gun to reduce tip clogs.

Hose wrap Rack

Stows paint hose. (LTS 17, ProLTS 17, and ProLTS 19 only)

Pail hanger (LTS 17, ProLTS

17, and ProLTS 19 only)

For transporting pail by its handle.

Component Identification

313034H 9

ti9669a

ti11987a

ti9368b

ti9346a

ti9670a

ti9724a

ti11988a

V (SG2/SG3)

Operation

10 313034H

Operation

Trigger Lock

Always engage the trigger lock when you stop spraying

to prevent the gun from being triggered accidentally by

hand or if dropped or bumped.

Pressure Relief Procedure

Follow this Pressure Relief Procedure whenever you

stop spraying and before cleaning, checking, servicing,

or transporting equipment.

1. Turn power switch OFF and unplug

power cord.

2. Turn Prime/Spray valve to

PRIME to relieve pressure.

3. Hold gun firmly to side of pail.

Trigger the gun to relieve

pressure.

4. Engage trigger lock.

NOTE: Leave Prime/Spray valve in the PRIME

position until you are ready to spray again.

If you suspect the spray tip or hose is clogged or that

pressure has not been fully relieved after following the

steps above, VERY SLOWLY loosen tip guard retaining

nut or hose end coupling to relieve pressure gradually,

then loosen completely. Clear hose or tip obstruction.

Read Unclogging Spray Tip, page 14.

NOTE: To select function, align symbol on pressure control knob with setting indicator on sprayer.

ti8908a

Trigger Locked

Trigger Unlocked

ti8909a

ti2810a

ti9346a

ti11986a

ti8908a

Pressure Control Knob Settings

High Pressure

Spray

Low Pressure

Spray

Prime/

Clean

Rolling

ti5597a

Setup

313034H 11

Setup

1. Unscrew tip and guard assembly

from gun.

2. Uncoil hose and connect one

end to gun. Use two

wrenches to tighten securely

3. Connect other

end of hose to

sprayer.

NOTE: If hose is already connected, make sure connec-

tions are tight.

4. Turn OFF power switch.

5. Turn Pressure Control Knob

all the way left (counter-clockwise)

to minimum pressure.

Prime and Flush Storage Fluid

NOTE: To spray lacquers with the ProLTS 17 and

ProLTS 19, you must purchase lacquer conversion kit

256212, and follow priming procedure for oil-based

materials. The LTS 15 and LTS 17 units are not intended

for lacquers.

Before you use your sprayer for the first time or be-

gin a new spraying project, you need to prime the

sprayer and flush the storage fluid out of the spray-

er.

Oil- or Water-based Materials

• When spraying water-based materials, flush the

system thoroughly with water.

• When spraying oil-based materials, flush the sys-

tem thoroughly with mineral spirits or compatible,

oil-based flushing solvent.

• To spray water-based materials after spraying

oil-based materials, flush the system thoroughly

with water first. The water flowing out of prime tube

should be clear and solvent-free before you begin

spraying the water-based material.

• To spray oil-based materials after spraying

water-based materials, flush the system thoroughly

with mineral spirits or a compatible oil-based flush-

ing solvent first. The solvent flowing out of the prime

tube should not contain any water.

• When flushing with solvents, ground pail and gun.

Read Grounding and Electric Requirements, page

• To avoid fluid splashing back on your skin or into

your eyes, always aim gun at inside wall of pail.

ti11978a

ti11977a

ti9674b

(ProLTS)

ti11456a

(LTS15, LTS 17)

ti2810a

ti9344a

Setup

12 313034H

1. Make sure the power switch is OFF

and the sprayer is unplugged.

2. Separate prime tube (smaller)

from suction tube (larger).

3. Place prime tube in waste pail.

4. Submerge suction tube in

water or flushing solvent.

5. Turn Prime/Spray Valve to

PRIME.

6. Plug sprayer in a grounded out-

let.

7. Turn power switch ON.

8. Align setting indicator with

Prime/Clean setting on Pres-

sure Control knob until pump

starts, page 10.

9. When sprayer starts pumping, flushing solvent and

air bubbles will be purged from system. Allow fluid to

flow out of prime tube, into waste pail, for 30 to 60

seconds.

10. Turn power switch OFF.

11. Transfer suction tube to paint

pail and submerge suction tube

in paint.

12. Turn power switch ON.

13. When you see paint coming

out of prime tube:

a. Point gun into waste pail.

b. Unlock gun trigger lock.

c. Pull and hold gun trigger.

d. Turn Prime/Spray valve to

SPRAY.

NOTE: Some fluids may prime faster if the Power Switch

is momentarily turned off so the pump can slow and

stop. Repeat several times if necessary.

14. Continue to trigger gun into waste pail until you see

only paint coming out of gun.

15. Release trigger. Engage trig-

ger lock.

16. Transfer prime tube to paint pail

and clip prime tube to suction

tube.

• Motor stopping indicates pump

and hose are primed with paint.

NOTE: If motor continues to run the sprayer is not prop-

erly primed. To reprime, turn Prime/Spray valve to

PRIME and repeat step 12.

ti2810a

ti2039a

ti9652a

ti9651a

ti9346a

ti5580a

ti9718a

ti2810a

ti9653a

ti5580a

ti9345a

ti8909a

ti8908a

Setup

313034H 13

Install Tip and Guard on Gun

1. Engage trigger lock.

2. Verify tip and guard parts are assembled in order

shown.

3. Screw tip and guard assembly on gun. Tighten

retaining nut.

4. Make sure spray tip is pointing forward in spray posi-

tion.

Spraying Techniques

Preventing Excessive Tip Wear

• Spray should be atomized (evenly distributed, no

gaps at edges). Start at low pressure setting,

increase pressure a little at a time until you see a

good spray pattern, without tails.

• Spray at lowest pressure that atomizes paint.

• If maximum sprayer pressure is not enough for a

good spray pattern, tip is too worn. See Reversible

Spray Tip Selection Chart, page 16.

NOTE: If tails persist when spraying at the highest pres-

sure, a smaller tip is needed or the material may need to

be thinned.

Adjust Spray Pressure

This sprayer is set up for most airless spraying applica-

tions. Details on tip selection, tip wear, coat thickness,

etc. are provided on page 15.

NOTE: Motor only runs when gun is triggered. Sprayer

is designed to stop pumping when gun trigger is

released.

Align setting indicator with function symbol on Pressure

Control knob, page 10.

• Turning knob to right (clockwise), increases pres-

sure at gun.

• Turning it left (counter-clockwise), decreases pres-

sure.

• General spraying instructions are provided in Get-

ting Started with Basic Spraying Techniques section

of this manual, page 17.

ti8908a

retaining nut

black rubber gasket and

guard

tip

ti8911a

metal seat

Use tip to align seat

Tip must be pushed

all the way into guard

in guard

ti9574a

ti5606a

ti11981a

ti9049a

ti5592a

tails-gaps

at edges

pressure

good

spray pattern

too low

Setup

14 313034H

Unclogging Spray Tip

To avoid fluid splash-back:

• Never pull gun trigger when arrow-shaped handle is

between SPRAY and UNCLOG positions.

• Tip must be pushed all the way into guard.

1. To UNCLOG tip obstruction,

engage trigger lock.

2. Point arrow-shaped handle

backward to UNCLOG posi-

tion.

3. Aim gun at piece of scrap or

cardboard.

4. Unlock trigger lock. Pull trig-

ger to clear clog.

5. When obstruction is

cleared, engage trigger

lock and rotate

arrow-shaped handle back

to SPRAY position.

Point the arrow-shaped

handle on the spray tip forward to SPRAY and

backward to UNCLOG obstructions.

ti8908a

ti9048a

ti8909a

ti9049a

Setup

313034H 15

Tip Selection

Selecting Tip Hole Size

Tips come in a variety of hole sizes for spraying a range

of fluids. Your sprayer includes an 0.015 in (0.38 mm) tip

for use in most spraying applications. Use the following

table to determine the range of recommended tip hole

sizes for each fluid type. If you need a tip other than the

one supplied, see the Reversible Tip Selection Chart

on page 16.

HINTS:

• As you spray, the tip wears and enlarges. Starting

with a tip hole size smaller than the maximum will

allow you to spray within the rated flow capacity of

the sprayer.

• Maximum tip hole sizes supported by the sprayer:

– LTS 15: 0.015 in. (0.38 mm)

– LTS 17: 0.017 in. (0.43 mm)

– ProLTS 17: 0.017 in. (0.43 mm)

– ProLTS 19: 0.019 in. (0.48 mm)

Choosing the Correct Tip

Consider coating and surface to be sprayed. Make sure

you use best tip hole size for that coating and best fan

width for that surface.

Tip Hole Size

Tip hole size controls flow rate - the amount of paint that

comes out of the gun.

HINTS:

• Use larger tip hole sizes with thicker coatings and

smaller tip hole sizes with thinner coatings.

• Maximum tip hole sizes supported by sprayer:

– LTS 15: 0.015 in. (0.38 mm)

– LTS 17: 0.017 in. (0.43 mm)

– ProLTS 17: 0.017 in. (0.43 mm)

– ProLTS 19: 0.019 in. (0.48 mm)

• Tips wear with use and need periodic replacement.

Fan Width

Fan width is the size of the spray pattern, which deter-

mines the area covered with each stroke. Narrower fans

deliver a thicker coat, and wider fans deliver a thinner

coat.

HINTS:

• Select a fan width best suited to the surface being

sprayed.

• Wider fans allow provide better coverage on broad,

open surfaces.

• Narrower fans provide better control on small, con-

fined surfaces.

Coatings

Tip Hole Size Stains Enamels Primers Interior Paints Exterior Paints

0.011 in. (0.28 mm)

✔

0.013 in. (0.33 mm)

✔✔✔ ✔

0.015 in. (0.38 mm)

✔✔ ✔ ✔

0.017 in. (0.43 mm)

✔✔ ✔

0.019 in. (0.48 mm)

✔

Setup

16 313034H

Understanding Tip Number

The last three digits of tip number (i.e.: 221413) contain

information about hole size and fan width on surface

when gun is held 12 in. (30.5 cm) from surface being

sprayed.

Reversible Tip Selection Chart

Example: For an 8 to 10 in. (203 to 254 mm) fan

width and 0.013 (0.33 mm) hole size, order Part No.

221413.

First digit when doubled

= approximate

fan width

413 tip has

8-10 in.

fan width

413 tip has

a 0.013 in

hole size

Last two digits = tip hole size in thousands of an inch

ti5559a

Tip

Part

No.

Fan Width 12 in.

(305 mm) from

surface Hole Size

221311 6 - 8 in.

(152 - 203 mm)

0.011 in.

(0.28 mm)

221411 8 - 10 in.

(203 - 254 mm)

0.011 in.

(0.28 mm)

221313 6 - 8 in.

(152 - 203 mm)

0.013 in.

(0.33 mm)

221413 8 - 10 in.

(203 - 254 mm)

0.013 in.

(0.33 mm)

221415 8 - 10 in.

(203 - 254 mm)

0.015 in.

(0.38 mm)

221515 10 - 12 in.

(254 - 305 mm)

0.015 in.

(0.38 mm)

221417 8 - 10 in.

(203 - 254 mm)

0.017 in.

(0.43 mm)

221517 10 - 12 in.

(254 - 305 mm)

0.017 in.

(0.43 mm)

221619 12 - 14 in.

(305 - 356 mm)

0.019 in.

(0.48 mm)

Getting Started With Basic Techniques

313034H 17

Getting Started With Basic Techniques

Use a piece of scrap cardboard to practice these basic

spraying techniques before you begin spraying the sur-

face.

• Hold gun 12 in. (30 cm) from surface and aim

straight at surface. Tilting gun to direct spray angle

causes an uneven finish.

• Flex wrist to keep gun pointed straight. Fanning gun

to direct spray at angle causes uneven finish.

Triggering Gun

Pull trigger after starting stroke. Release trigger before

end of stroke. Gun must be moving when trigger is

pulled and released.

Aiming Gun

Aim tip of gun at bottom edge of previous stroke, over-

lapping each stroke by half.

12 in.

(30 cm)

even

finish

thick

thin

uneven

finish

ti5585a

even finish thin thick thin

ti2036a

ti2037a

ti2038a

Shutdown and Cleaning

18 313034H

Shutdown and Cleaning

Pail Flushing

• For short term shutdown periods (overnight to two

days) refer to Short Term Storage, page 23.

• For flushing after spraying oil-based coatings, use

compatible oil-based flushing fluid or mineral spirits.

Read Priming and Flushing Storage Fluid, page 11.

• For flushing after spraying water-based coatings,

use water. Read Priming and Flushing Storage

Fluid, page 11 or Power Flush, page 20.

1. Relieve pressure, page 10.

2. Remove tip and guard assembly from gun and place

in flushing fluid.

3. Lift suction tube and prime tube from paint pail. Let

them drain into paint pail for a while.

4. Separate prime tube (smaller) from

suction tube (larger).

5. Place empty waste and

water or solvent pails side

by side.

6. Place prime tube in waste pail.

7. Submerge suction tube in

water or flushing solvent.

8. Turn pressure control knob to

the Prime/Clean setting.

9. Turn power switch ON.

10. Flush until approximately

1/3 of the flushing fluid is emptied from the pail.

11. Turn power switch OFF.

ti2039a

ti9726a

ti9652a

ti9651a

ti9344a

ti5580a

ti2018a

Shutdown and Cleaning

313034H 19

NOTE: Step 12 is for returning paint in hose back to

paint pail. One 50-ft hose holds approximately 1-quart

(1-liter) of paint.

12. To preserve paint in hose:

a. Point gun into paint pail.

b. Unlock gun trigger lock.

c. Pull and hold gun trigger.

d. Turn Prime/Spray valve to

SPRAY.

e. Turn power switch ON.

f. Continue to hold gun trigger until you see paint

diluted with flushing fluid starting to come out of

gun.

13. While continuing to trigger

gun, quickly move gun to

redirect spray into waste

pail. Continue triggering gun

into waste pail until flushing

fluid dispensed from gun is

relatively clear.

14. Stop triggering gun. Engage the

trigger lock.

15. Turn prime/spray valve to

Prime.

16. Turn power switch OFF.

17. Clean InstaClean Fluid Filter

and gun, page 22.

18. Fill unit with Pump Armor

™

storage fluid. Read Long

Term Storage, page 23.

o preserve paint in hose, trigger gun into paint pail

to expel the remaining paint.

ti9345a

ti5580a

ti8909a

ti9745a

ti8908a

ti9346a

ti2018a

Shutdown and Cleaning

20 313034H

Power Flush

Power flushing is a faster method of flushing. It can only

be used after spraying water-based coatings.

1. Relieve pressure, page 10.

2. Remove tip and guard assembly from gun and place

in waste pail.

3. Place empty waste and

paint pails side by side.

4. Lift suction tube and prime

tube from paint pail. Let them drain into paint for a

while.

5. Place suction and prime tube in waste pail.

6. Turn Pressure Control knob to the

Prime/Clean setting.

7. Screw power flush attachment to

garden hose. Close valve.

8. Turn on water. Open valve. Rinse

paint off suction tube, prime tube

and inlet screen.

9. Turn lever to close power flush

attachment.

10. Unscrew inlet screen from suction

tube. Place inlet screen in waste pail.

11. Connect garden hose to suction tube

with Power Flush attachment. Leave

prime tube in waste pail.

12. Turn power switch ON.

13. Open lever on Power Flush

attachment.

14. Circulate water through

sprayer, into waste pail, for 20 seconds.

15. Turn power switch OFF.

ti9726a

ti9344a

ti9413a

ti9727a

ti2040a

ti2042a

ti5580a

OPEN

ti2043a

ti2018a

Page is loading ...

Graco 24N808 Specification

Brand: Graco

Model: 24N808

Category: Garden tools

Type: Specification

This manual is also suitable for

Download PDF

report

Graco 24N808 Specification

This manual is also suitable for

Graco 24N808 Specification

Related papers

Other documents