Thermador MED302 User manual

Page is loading ...

Questions?

1-800-735-4328

www.thermador.com

We look forward to hearing from you!

This Thermador Appliance is made by

BSH Home Appliances Corporation

5551 McFadden Ave.

Huntington Beach, CA 92649

3

Safety

WARNING: If the information in this manual is not followed exactly, fire or shock

may result causing property damage or personal injury.

WARNING: Do not repair or replace any part of the appliance unless specifically

recommended in the manuals. Improper installation, service or maintenance can

cause injury or property damage. Refer to this manual for guidance. All other ser-

vicing should be done by a qualified technician.

Appliance Handling Safety

Do not lift appliance by door handle. Remove the door for easier handling and in-

stallation. See instructions in Use and Care Manual.

Unit is heavy and requires at least two people or proper equipment to move.

Hidden surfaces may have sharp edges. Use caution when reaching behind or un-

der appliance.

Safety Codes and Standards

This appliance complies with one or more of the following Standards:

• UL 858, The Standard for the Safety of Household Electric Ranges

• UL 923, The Standard for the Safety of Microwave Cooking Appliances

• UL 507, The Standard for the Safety of Electric Fans

• ANSI Z21.1, The American National Standard for Household Cooking Gas Ap-

pliances

• CAN/CSA-C22.2 No. 113-M1984 Fans and Ventilators

• CAN/CSA-C22.2 No. 61-M89 Household Cooking Ranges

It is the responsibility of the owner and the installer to determine if additional re-

quirements and/or standards apply to specific installations.

Electric Safety

Before you plug in an electrical cord, be sure all controls are in the OFF position.

If required by the National Electrical Code (or Canadian Electrical Code), this ap-

pliance must be installed on a separate branch circuit.

Installer - show the owner the location of the circuit breaker or fuse. Mark it for easy

reference.

Important - Save these instructions for the local electrical inspector's use.

Before installing, turn power OFF at the service panel. Lock service panel to pre-

vent power from being turned ON accidentally.

Refer to data plate for more information. See "Product Data Plate" under "Service"

for data plate location.

Be sure your appliance is properly installed and grounded by a qualified technician.

Installation, electrical connections and grounding must comply with all applicable

codes.

m

Important Safety Instructions

READ AND SAVE THESE INSTRUCTIONS

4

Related Equipment Safety

Remove all tape and packaging before using the appliance. Destroy the packaging

after unpacking the appliance. Never allow children to play with packaging materi-

al.

Never modify or alter the construction of the appliance. For example, do not re-

move leveling legs, panels, wire covers or anti-tip brackets/screws.

Transport

To avoid damage to the oven vent, use the transport method shown in the picture

below.

m

Important Safety Instructions

READ AND SAVE THESE INSTRUCTIONS

5

Installation

Before you Begin

Tools and Parts Needed

• Phillips head screwdriver

• Measuring tape

• Drill with bit (1/8")

Parts Included

• Phillips head screws (6)

27” Appliances

General Information

Power Requirements

The outlet must be properly grounded in accordance with all applicable codes.

Dimensions for 27” Wall-Mounted Units

Single Oven 27”

It is good practice, when oven is in-

stalled at the end of a cabinet run, ad-

jacent to a perpendicular wall or

cabinet door, to allow at least 1/4”

space between the side of the oven

and the wall/door.

For oven support, install 2x4’s extend-

ing front to back flush with the bottom

and the side of the opening. The sup-

porting base must be well secured to

the floor/cabinet and level.

Note: The conduit box must be in-

stalled either above or below the unit. If

the conduit box is installed below the

unit, a 2” diameter hole or space is re-

quired between the back wall and the

right rear of the 2x4 supports.

The cabinet base must be flat and

capable of supporting a weight of at

least 210 lbs (95 kg).

6

Double Oven 27”

It is good practice, when oven is in-

stalled at the end of a cabinet run, ad-

jacent to a perpendicular wall or

cabinet door, to allow at least 1/4”

space between the side of the oven

and the wall/door.

For oven support, install 2x4’s extend-

ing front to back flush with the bottom

and the side of the opening. The sup-

porting base must be well secured to

the floor/cabinet and level.

Note: The conduit box must be located

above the unit to facilitate connecting

and servicing.

The cabinet base must be flat and

capable of supporting a weight of at

least 355 lbs (161 kg).

Combo Oven with Microwave 27”

It is good practice, when oven is in-

stalled at the end of a cabinet run, ad-

jacent to a perpendicular wall or

cabinet door, to allow at least 1/4”

space between the side of the oven

and the wall/door.

For oven support, install 2x4’s extend-

ing front to back flush with the bottom

and the side of the opening. The sup-

porting base must be well secured to

the floor/cabinet and level.

Note: The conduit box must be located

above the unit to facilitate connecting

and servicing.

The cabinet base must be flat and

capable of supporting a weight of at

least 330 lbs (150 kg).

7

Combo Oven with Microwave and

Warming Drawer 27”

It is good practice, when oven is in-

stalled at the end of a cabinet run, ad-

jacent to a perpendicular wall or

cabinet door, to allow at least 1/4”

space between the side of the oven

and the wall/door.

For oven support, install 2x4’s extend-

ing front to back flush with the bottom

and the side of the opening. The sup-

porting base must be well secured to

the floor/cabinet and level.

Note: The conduit box must be located

above the unit to facilitate connecting

and servicing.

The cabinet base must be flat and

capable of supporting a weight of at

least 370 lbs (168 kg).

8

A single oven installed under the

counter allows for the installation of

most Thermador Gas or Electric

non-Cook’n’Vent® Model Cook-

tops. Downdraft units cannot be in-

stalled in this configuration;

Thermador overhead ventilation is

recommended.

Some TMH cooktops require addi-

tional clearances to combustible

walls.

A Thermador cooktop should be in-

stalled on the same center line as

the under-the-counter single oven.

Follow the installation instructions

provided with cooktop for installa-

tion of cooktops. 3 3/4” (95 mm)

minimum is required from the top of

the countertop to the top of the cut-

out opening for under-counter in-

stallation with Thermador cooktops.

If the type of cabinet or countertop

thickness does not provide for this

minimum space, the cabinet base

may have to be lowered, into the toe

space, to provide the necessary

space above the oven. However, a

4” minimum distance between the

floor and the oven bottom must re-

main.

27” Under-the-counter units

9

30” Appliances

Dimensions for 30” Wall-Mounted Units

Single Oven 30”

It is good practice, when oven is in-

stalled at the end of a cabinet run, ad-

jacent to a perpendicular wall or

cabinet door, to allow at least 1/4”

space between the side of the oven

and the wall/door.

For oven support, install 2x4’s extend-

ing front to back flush with the bottom

and the side of the opening. The sup-

porting base must be well secured to

the floor/cabinet and level.

Note: The conduit box must be in-

stalled either above or below the unit. If

the conduit box is installed below the

unit, a 2” diameter hole or space is re-

quired between the back wall and the

right rear of the 2x4 supports.

The cabinet base must be flat and

capable of supporting a weight of at

least 190 lbs (86 kg).

10

Double Oven 30”

It is good practice, when oven is in-

stalled at the end of a cabinet run, ad-

jacent to a perpendicular wall or

cabinet door, to allow at least 1/4”

space between the side of the oven

and the wall/door.

For oven support, install 2x4’s extend-

ing front to back flush with the bottom

and the side of the opening. The sup-

porting base must be well secured to

the floor/cabinet and level.

Note: The conduit box must be located

above the unit to facilitate connecting

and servicing.

The cabinet base must be flat and

capable of supporting a weight of at

least 330 lbs (150 kg).

Combo Oven with Microwave 30”

It is good practice, when oven is in-

stalled at the end of a cabinet run, ad-

jacent to a perpendicular wall or

cabinet door, to allow at least 1/4”

space between the side of the oven

and the wall/door.

For oven support, install 2x4’s extend-

ing front to back flush with the bottom

and the side of the opening. The sup-

porting base must be well secured to

the floor/cabinet and level.

Note: The conduit box must be located

above the unit to facilitate connecting

and servicing.

The cabinet base must be flat and

capable of supporting a weight of at

least 290 lbs (132 kg).

11

Combo Oven with Microwave and

Warming Drawer 30”

It is good practice, when oven is in-

stalled at the end of a cabinet run, ad-

jacent to a perpendicular wall or

cabinet door, to allow at least 1/4”

space between the side of the oven

and the wall/door.

For oven support, install 2x4’s extend-

ing front to back flush with the bottom

and the side of the opening. The sup-

porting base must be well secured to

the floor/cabinet and level.

Note: The conduit box must be located

above the unit to facilitate connecting

and servicing.

The cabinet base must be flat and

capable of supporting a weight of at

least 310 lbs (141 kg).

Combo Oven with Warming

Drawer 30”

It is good practice, when oven is in-

stalled at the end of a cabinet run, ad-

jacent to a perpendicular wall or

cabinet door, to allow at least 1/4”

space between the side of the oven

and the wall/door.

For oven support, install 2x4’s extend-

ing front to back flush with the bottom

and the side of the opening. The sup-

porting base must be well secured to

the floor/cabinet and level.

Note: The conduit box must be located

above the unit to facilitate connecting

and servicing.

The cabinet base must be flat and

capable of supporting a weight of at

least 290 lbs (132 kg).

12

30” Under-the-counter-Units

A single oven installed under the

counter allows for the installation

of most Thermador Gas or Electric

non-Cook’n’Vent® Model Cook-

tops. Downdraft units cannot be

installed in this configuration;

Thermador overhead ventilation is

recommended.

Some TMH cooktops require addi-

tional clearances to combustible

walls.

A Thermador cooktop should be

installed on the same center line

as the under-the-counter single

oven. Follow the installation in-

structions provided with cooktop

for installation of cooktops. 3 3/4”

inches (95mm) minimum is re-

quired from the top of the counter-

top to the top of the cutout opening

for under-counter installation with

Thermador cooktops. If the type of

cabinet or countertop thickness

does not provide for this minimum

space, the cabinet base may have

to be lowered, into the toe space,

to provide the necessary space

above the oven. However, a 4”

minimum distance between the

floor and the oven bottom must re-

main.

13

Electrical Installation

All model ovens on the front cover are dual rated, designed to be connected to ei-

ther 208/240V AC, 60 Hz, 4 wire, single-phase power supply.

The electrical supply should be a 4-wire single-phase AC. Install a suitable conduit

box (not furnished).

Important: Local Codes may vary, installation, electrical connections and ground-

ing must comply with all applicable local codes.

If local codes permit grounding through the electrical supply neutral, connect both

the white neutral wire and the bare ground wire from the oven to the white neutral

electrical supply wire.

Electrical Connection

1. Connect the red oven wire to the red electrical supply wire (hot wire).

2. Connect the black oven wire to the black electrical supply wire (hot wire).

3. Connect the white neutral oven wire to the white neutral (not bare ground)

electrical supply wire.

4. Connect the bare ground oven wire to the bare ground electrical supply wire.

The conduit cable, where connected at the oven, swivels. Rotate conduit cable up-

ward (or downward) and direct through hole prepared in cabinet to attach to J-Box.

To facilitate maintain serviceability, the flex conduit must not be shortened and

should be routed to permit temporary removal of the oven.

Model Circuit Required

208V, 60 Hz 240V, 60 Hz

M271, M301 25 AMP 30 AMP

ME301, MEW301

ME271, PO301,

POD301, DE301,

DEC301

30 AMP 30 AMP

ME302, MED302

ME272, MED272,

PO302, POD302,

PODC302, DE302,

MEM271, MEM301,

POM301, MEMC301,

MEMCW301,

MEMW271, MEMW301,

POMW301

40 or 50 Amp circuit. Refer to local electrical codes

for de-rating requirements.

14

Installing the Oven

Note: Before installing the oven be sure to verify the cabinet dimensions and elec-

trical connections.

Removing the Oven Door

For ease of installation, some oven doors may be removed to reduce the weight of

the oven by 30 lbs (14 kg) per door, before installing into the cabinet. See instruc-

tions below.

To remove the oven door:

m

CAUTION: When removing the door:

• Make sure oven is cool and power to the oven has been turned off

before removing the door. Failure to do so could result in electrical

shock or burns.

• The oven door is heavy and fragile. Use both hands to remove the

oven door. The door front is glass. Handle carefully to avoid

breaking.

• Grasp only the sides of the oven door. Do not grasp the handle as

it may swing in your hand and cause damage or injury.

• Failure to grasp the oven door firmly and properly could result in

personal injury or product damage.

• To avoid injury from hinge bracket snapping closed, be sure that

both levers are securely in place before removing the door. Also,

do not force door open or closed - the hinge could be damaged

and injury could result.

1. Be sure to read the above CAUTION

before attempting to remove the door.

2. Open the door completely.

3. Flip levers on hinges toward you.

4. Close door carefully until it stops. It will

be about half way closed.

5. Holding the door firmly on both sides

using both hands, pull the door up and

out of the hinge slots. Hold firmly; the

door is heavy.

6. Place the door in a convenient and sta-

ble location for cleaning.

15

To replace the oven door:

Service

Before Calling Service

See Use and Care Manual for troubleshooting information. Refer to the Warranty

in the Use an Care Manual.

To reach a service representative, see the contact information at the front of the

manual. Please be prepared with the information printed on your product data plate

when calling.

Data Plate

The data plate shows the model and serial number. Refer to the data plate on the

appliance when requesting service. The data plate is located on the underside of

the control panel:

1. Holding the door firmly in both hands,

place hinges in hinge slots.

2. Open door all the way to expose hinges

and slots.

3. Push lever down and away from you

until flush with the bracket.

4. Close and open door slowly to be sure

it is correctly and securely in place.

Door must be straight, not crooked.

Data Plate

Page is loading ...

5551 McFadden Avenue, Huntington Beach, CA 92649 • 800-735-4328 • www.thermador.com

Litho in USA

Thermador MED302 User manual

Thermador MED302 User manual

in other languages

Related papers

Other documents