Maytag JMV9169 Installation Instructions Manual

Installation Instructions

Over the Range Microwave Oven

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT -- Save these instructions for

local inspector's use.

• IMPORTANT -- Observe all governing codes

and ordinances.

• Note to Installer- Be sure to leave these

instructions with the Consumer.

• Note to Consumer- Keep these instructions for

future reference.

• Skill level - Installation of this appliance requires

basic mechanical and electrical skills.

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not

covered under the Warranty.

READ CAREFULLY. KEEP THESE INSTRUCTIONS.

Installation Instructions

CONTENTS

General information

Important Safety Instructions ..................... 3

Electrical Requirements .............................. 3

Hood Exhaust ........................................... 4, 5

Damage - Shipment/Installation ................. 6

Parts Included ............................................... 6

Tools You Will Need ..................................... 7

Mounting Space ............................................ 7

Step-by-step installation guide

Placement of Mounting Plate ................ 8-10

Removing the Mounting Plate ................... 8

Finding the Wall Studs .............................. 8

Determining Wall Plate Location ............... 9

Aligning the Wall Plate ............................ 10

Installation Types ................................. 11-21

A Recircutating ........................................... 12-13

Attach Mounting Plate to Wall ................. 12

Preparation of Top Cabinet ..................... 12

Mount the Microwave Oven ..................... 13

B Outside Top Exhaust .............................. 14-17

Attach Mounting Plate to Wall ................. 14

Preparation of Top Cabinet ..................... 15

Adjust Blower .......................................... 15

Check Damper Operation ........................ 16

Mount Microwave Oven ........................... 16

Adjust Exhaust Adaptor ........................... 17

Connecting Ductwork .............................. 17

C Outside Back Exhaust ............................. 18-21

Preparing Rear Wall ................................ 18

Attach Mounting Plate to Wall ........... 18, 19

Preparation of Top Cabinet ..................... 19

Adjust Blower .................................... 19, 20

Mount the Microwave Oven ............... 20, 21

Before You Use Your Microwave .............. 22

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

This product requires a three-prong grounded outlet.

The installer must perform a ground continuity check

on the power outlet box before beginning the

installation to insure that the outlet box is properly

grounded. If not properly grounded, or if the outlet

box does not meet electrical requirements noted

(under ELECTRICAL REQUIREMENTS), a qualified

electrician should be employed to correct any

deficiencies.

CAUTION: For personal

safety, remove house fuse or

open circuit breaker before

beginning installation to

avoid severe or fatal shock

injury.

CAUTION: For personal safety, the mounting

surface must be capable of supporting the

cabinet load, in addition to the added weight of

this 59 pound product, plus additional oven loads

of up to 50 pounds or a total weight of 109

pounds.

CAUTION: For personal safety, this product

cannot be installed in cabinet arrangements such

as an island ora peninsula. It must be mounted to

BOTH a top cabinet AND a wall.

NOTE: For easier installation and personal

safety, it is recommended that two people install

this product.

IMPORTANT-PLEASE READ CAREFULLY. FOR

PERSONAL SAFETY, THIS APPLIANCE MUST BE

PROPERLY GROUNDED TO AVOID SEVERE OR

FATAL SHOCK.

Insure proper

ground exists

before use

The power cord of this

appliance is equipped

with a three-prong

(grounding) plug which

mates with a standard

three-prong (grounding)

wall receptacle to

minimize the possibility

of electric shock hazard

from this appliance.

You should have the wall receptacle and circuit

checked by a qualified electrician to make sure

the receptacle is properly grounded.

Where a standard two-prong wall receptacle is

encountered, it is very important to have it

replaced with a properly grounded three-prong

wall receptacle, installed by a qualified

electrician.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT,

DEFORM OR REMOVE ANY OF THE PRONGS

FROM THE POWER CORD. DO NOT USE WITH

AN EXTENSION CORD.

ELECTRICAL REQUIREMENTS

Product rating is 120 volts AC, 60 Hertz,

-MMV4205, AMV5206, MMV5207, JMV8208 (USA):

14.8 amps and 1.7 kilowatts.

-MMV5207,JMV8208 (CANADA) / AMV6167:

13 amps and 1.5 kilowatts.

-JMV8166/JMV9169:

14.5 amps and 1.6 kilowatts.

This product must be connected to a supply circuit of

the proper voltage and frequency. Wire size must

conform to the requirements of the National Electrical

Code or the prevailing local code for this kilowatt

rating. The power supply cord and plug should be

brought to a separate 20 ampere branch circuit single

grounded outlet. The outlet box should be located in

the cabinet above the microwave oven. The outlet

box and supply circuit should be installed by a

qualified electrician and conform to the National

Electrical Code or the prevailing local code.

3

Installation Instructions

HOOD EXHAUST

NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to

recirculate the air back into the room, proceed to page 11.

OUTSIDE TOP EXHAUST (EXAMPLE ONLY)

The following chart describes an example of one possible ductwork installation.

DUCT PIECES

Roof Cap

12 Ft. Straight Duct (6"

Round)

EQUIVALENT NUMBER

LENGTH x USED

24 Ft. x (1)

12 Ft. x (1)

[]

Rectangular-to-Round 5 Ft.

Transition Adaptor*

Equivalent lengths of duct pieces are based on actual

tests and reflect requirements for good venting

performance with any vent hood.

x (1)

Total Length

EQUIVALENT

= LENGTH

= 24 Ft.

= 12 Ft.

= 5 Ft.

= 41 Ft.

* IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper will have

to be cut to fit, using the tin snips, in order to allow free movement of the damper.

OUTSIDE BACK EXHAUST (EXAMPLE ONLY)

The following chart describes an example of one possible ductwork installation.

DUCT PIECES EQUIVALENT NUMBER EQUIVALENT

LENGTH* x USED = LENGTH

Roof Cap 40 Ft. x (1) = 40 Ft.

- 3 Ft. Straight Duct

(3¼"x10" 3Ft. x (1) = 3Ft.

Rectangular)

(_ 90 ° Elbow 10 Ft. x (2) = 20 Ft.

Equivalent lengths of duct pieces are based on actual

tests and reflect requirements for good venting

performance with any vent hood. Total Length = 63 Ft.

NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be

prepared at the time it is constructed by leaving enough space between the wall studs to accommodate

exhaust.

4

Installation Instructions

NOTE: If you need to install ducts, note that the total

duct length of 3¼" x 10" rectangular or 6" diameter

round duct should not exceed 60 equivalent feet.

Outside ventilation requires a HOOD EXHAUST

DUCT. Read the following carefully.

NOTE: It is important that venting be installed using

the most direct route and with as few elbows as

possible. This ensures clear venting of exhaust and

helps prevent blockages. Also, make sure dampers

swing freely and nothing is blocking the ducts.

Exhaust connection:

The hood exhaust has been designed to mate with a

standard 3¼"x 10" rectangular duct.

If a round duct is required, a rectangular-to-round

transition adaptor must be used. Do not use less

than a 6" diameter duct.

Maximum duct length:

For satisfactory air movement, the total duct length of

3¼" x 10" rectangular or 6" diameter round duct

should not exceed 60 equivalent feet.

Elbows, transitions, wall and roof

caps, etc., present additional resistance to

airflow and are equivalent to a section of straight duct

which is longer than their actual physical size. When

calculating the total duct length, add the equivalent

lengths of all transitions and adaptors plus the length

of all straight duct sections. The chart below shows

you how to calculate total equivalent ductwork length

using the approximate feet of equivalent length of

some typical ducts.

DUCT PIECES EQUIVALENT NUMBER EQUIVALENT

LENGTH x USED = LENGTH

Rectangular-to-Round

Transition Adaptor* 5 Ft. x ( = Ft.

Wall Cap 40 Ft. x ( = Ft.

(_ 90 ° Elbow 10 Ft. x ( = Ft.

(_ 45 ° Elbow 5 Ft. x ( = Ft.

90 ° Elbow 25 Ft. x ( = Ft.

45 ° Elbow 5 Ft. x ( = Ft.

Roof Cap 24 Ft. x ( = Ft.

-1 Straight Duct 6" Round or

3¼" x 10" Rectangular 1 Ft. x ( = Ft.

Total Ductwork = Ft.

* IMPORTANT: If a rectangular-to-

round transition adaptor is used, the

bottom corners of the damper will

have to be cut to fit, using the tin

snips, in order to allow free movement of the damper.

Equivalent lengths of duct pieces are based on actual

tests and reflect requirements for good venting

performance with any vent hood.

5

Installation Instructions

DAMAGE - SHIPMENT/

INSTALLATION

• If the unit is damaged in shipment, return the

unit to the store in which it was bought for repair

or replacement.

• If the unit is damaged by the customer, repair

or replacement is the responsibility of the

customer.

• If the unit is damaged by the installer (if other

than the customer), repair or replacement must

be made by arrangement between customer and

installer.

PARTS INCLUDED

HARDWARE PACKET

PART QUANTITY

Wood Screws 1

(¼" x 2")

Toggle Bolts 3

@_ (and wing nuts)

(3/1_"x 3")

Self-aligning 3

_/ Machine Screws

(¼"-28 x 3¼")

Nylon Grommet 2

(for metal cabinets)

You will find the installation hardware contained in a

packet with the unit. Check to make sure you have all

these parts.

NOTE: Some extra parts are included.

ADDITIONAL PARTS

PART

TOP CABINET TEMPLATE

REAR WALL TEMPLATE

Top Cabinet

Template

Rear Wall

Template

Installation

Instructions

Separately

Packed

Grease

Filters

Exhaust

adaptor

QUANTITY

1

6

Installation Instructions

TOOLS YOU WILL NEED

Ruler or tape measure

..... _j _and straight edge

# ! and #2 Phillips screwdriver Pencil

Tin snips (for cutting

damper, if required)

Gloves

Scissors

(to cut template, if necessary)

Saw (saber, hole or keyhole)

Electric drill with 3/16", _/2"

and 5/8" drill bits

Stud finder or Hammer (optional)

(optional)

Filler blocks or scrap wood

pieces, if needed for top

cabinet spacing (used on

recessed bottom cabinet

installations only)

Safety goggles

Level

Duct and masking tape

MOUNTING SPACE

Bottom edge of

cabinet needs

to be 33" or

more from the

cooking

surface

Backsplash

NOTES:

• The space between the cabinets must be

30" wide and free of obstructions.

• This microwave oven is for installation over

ranges up to 33" wide.

• If you are going to vent your microwave

oven to the outside, see Hood Exhaust

Section for exhaust duct preparation.

• When installing the microwave oven

beneath smooth flat cabinets be careful

to follow the instructions on the top

cabinet template for power cord

clearance.

7

Installation Instructions

1.PLACEMENT OF THE MOUNTING PLATE

A. REMOVING THE MICROWAVE

OVEN FROM THE CARTON/

REMOVING THE MOUNTING

PLATE

1, Remove the installation instructions, Exhaust

adaptor, filters, glass tray and the small hardware

bag. Do not remove the Styrofoam protecting the

front of the oven.

2. Fold back all 4 carton flaps fully against carton

sides. Then carefully roll the oven and carton over

onto the top side. The oven should be resting in

the Styrofoam.

3. Pull the carton up and off the oven.

4. Remove and properly discard plastic bags.

Screws

Mounting Plate _

T

5, Remove the 2 screws from the mounting plate.

This plate will be used as the rear wall template

and for mounting.

NOTE: You will have to reuse two screws in original

loction of outcase after removing mounting plate.

B. FINDING THE WALL STUDS

1. Find the studs, using one of the following

methods:

A. Stud finder-a magnetic device which locates

nails.

OR

B. Use a hammer to tap lightly across the

mounting surface to find a solid sound. This

will indicate a stud location.

2, After locating the stud(s), find the center by

probing the wall with a small nail to find the edges

of the stud. Then place a mark halfway between

the edges. The center of any adjacent studs

should be 16" or 24" from this mark.

3, Draw a line down the center of the studs.

THE MICROWAVE MUST BE CONNECTED TO AT

LEAST ONE WALL STUD.

8

Installation Instructions

C. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET

Plate position - beneath flat bottom cabinet

Draw a vertical line on

the wall at the center of

the 30" wide space.

Tape the Rear Wall

Template onto the wall

matching the centeriine

and touching the

bottom of the cabinet.

_mmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmm|

Plate position - beneath framed recessed

cabinet bottom

33" to Cooktop

Draw a vertical line on the wall at the center of the

30" space.

Tape the Rear Wall Template onto the wall

matching the centeriine and touching the bottom

cabinet frame.

Plate position - beneath recessed bottom

cabinet with front overhang

'k

Your cabinets may have decorative trim that

interferes with the microwave installation. Remove

the decorative trim to install the microwave properly

and to make it level.

THE MICROWAVE MUST BE LEVEL.

Use a level to make sure the cabinet bottom is level.

If the cabinets have a front overhang only, with no

back or side frame, install the mounting plate down

the same distance as the front overhang depth. This

will keep the microwave level.

1. Measure the inside depth of the front overhang.

2. Draw a horizontal line on the back wall an equal

distance below the cabinet bottom as the inside

depth of the front overhang.

3. For this type of installation with front overhang

only, align the mounting tabs with this horizontal

line, not touching the cabinet bottom as described

in Step D.

Installation Instructions

D. ALIGNING THE WALL PLATE

Horizontal Line

I'''- 7

Area E

i

REAR WALk TEMPLATE

_;:_,,_!_:........................

Centedine Draw a Vertical Line

notches on Wallfrom Center

__ _<___ of Top Cabinet

o o o o o o o o o o

HoleC

CAUTION: Wear gloves to avoid cutting

fingers on sharp edges.

Hole B Horizontal Line

Draw a Horizontal line on wall from

bottom of "Rear Wall Template".

1, Draw a Vertical line on the wall at the center of the

30" wide space.

2. Draw a Horizontal line on the walt at the bottom of

"Rear Wall Template".

3. Drill 5/8" holes for toggle bolts on 3 locations

(Hole A, Hole B, Hole C) but if the location of hole

is same as that of stud, drill a 3/16" hole for wood

screw. In other words, toggle bolt can not be used

to the location of stud.

NOTE: DO NOT MOUNT THE PLATE AT THIS

TIME.

NOTE: Holes A, B and C are inside area E. If none of

A, B and C is in a stud, find a stud somewhere in area

E and draw a forth circle to line up with the stud. It is

important to use at least one wood screw mounted

firmly in a stud to support the weight of the

microwave. Set the mounting plate aside.

10

Installation Instructions

2. INSTALLATION TYPES (Choose A, B or C)

This microwave oven is designed for adaptation to

the following three types of ventilation:

A. Recirculating (Non-Vented Ductless)

B. Outside Top Exhaust (Vertical Duct)

C. Outside Back Exhaust (Horizontal Duct)

NOTE: This microwave is shipped after being

assembled for "Recirculating". And exhaust adaptor

is shipped assembled to the filler-upper. Select the

type of ventilation required for your installation and

proceed to that section.

A. RECIRCULATING

(NON-VENTED DUCTLESS)

B. OUTSIDE TOP EXHAUST

(VERTICAL DUCT)

Adaptor in Place for

Outside Top

_ Exhaust

C. OUTSIDE BACK EXHAUST

(HORIZONTAL DUCT)

11

Installation Instructions

A. RECIRCULATING (Non-Vented Ductless)

INSTALLATION OVERVIEW

A1. Attach Mounting Plate to Wall

A2. Prepare Top Cabinet

A3. Mount the Microwave Oven

+

AI.__.ATTACH THE MOUNTING PLATE

TO THE WALL

Attach the plate to the wall using toggle bolts. At least

one wood screw must be used to attach the plate to

a wall stud.

1, Remove the toggle wings from the bolts.

2, Insert the bolts into the mounting plate through

the holes designated to go into drywall and

reattach the toggle wings to 3A" onto each bolt.

To use toggle bolts:

Spacing for Toggles More

Than Wall Thickness

I Toggle Wings

Mount ng =

Plate

Wall

Bolt End

3. Place the mounting plate against the wall and

insert the toggle wings into the holes in the wall to

mount the plate.

NOTE: Before tightening toggle bolts and wood

screw, make sure to coincide bottom line of the

Mounting plate with Horizontal line of "Rear wall

Template" and then the Mounting plate is properly

centered under the cabinet.

CAUTION: Be careful to avoid pinching fingers

between the back of the mounting plate and the walt.

4. Tighten all bolts. Pull the plate away from the walt

to help tighten the bolts.

A2.__.USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

You need to drill holes for the top support screws and

a hole large enough for the power cord to fit through.

• Read the instructions on the TOP CABINET

TEMPLATE.

• Tape it underneath the top cabinet.

• Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes

in the cabinet bottom.

12

Installation Instructions

MOUNT THE MICROWAVE OVEN

FOR EASIER INSTALLATION AND PERSONAL

SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS MICROWAVE OVEN.

IMPORTANT: Do not grip or use handle during

installation.

NOTE: If your cabinet is metal, use the nylon

grommet around the power cord hole to prevent

cutting of the cord.

NOTE: We recommend using filler blocks if the

cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used, case

damage may occur from over tightening screws.

NOTE: When mounting the microwave oven, thread

power cord through hole in bottom of top cabinet.

Keep it tight throughout Steps 1-3. Do not pinch cord

or lift oven by pulling cord.

1. Lift microwave, tilt it

\ forward, and hook slots

at back bottom edge

onto four lower tabs of

mounting plate.

2, Rota;ce front of oven

up against cabinet

bottom j

3, Insert a self-aligning screw through top center

cabinet hole. Temporarily secure the oven by

turning the screw at least two full turns after the

threads have engaged. (It will be completely

tightened later.) Be sure to keep power cord

tight. Be careful not to pinch the cord,

especially when mounting flush to bottom of

cabinet.

Cabinet Front

Cabinet Bottom Shelf

FillerBlock

T Equivalent to

Depth of

Cabinet Recess

igning Screw

Microwave Oven Top

4. Attach the microwave oven to the top cabinet.

5, Insert 2 self-aligning screws through outer

top cabinet holes. Turn two full turns on

each screw.

6, Tighten center

screw completely.

7, Tighten the outer two screws to the top of the

microwave oven. (While tightening screws, hold

the microwave oven in place against the wall and

the top cabinet.)

L

8, Install grease filters. See the Owner's Manual

packed with the microwave.

13

Installation Instructions

B. OUTSIDE TOP EXHAUST (Vertical Duct)

INSTALLATION OVERVIEW

B1. Attach Mounting Plate to Walt

B2. Prepare Top Cabinet

B3. Adjust Blower

B4. Check Damper Operation

B5. Mount Microwave Oven

B6. Adjust Exhaust Adaptor

B7. Connect Ductwork

Blm ATTACH THE MOUNTING PLATE

TO THE WALL

Attach the plate to the wall using toggle bolts. At least

one wood screw must be used to attach

the plate to a wall stud.

1, Remove the toggle wings from the bolts.

2, Insert the bolts into the mounting plate through the

holes designated to go into drywall and reattach

the toggle wings to 3A" onto each bolt.

To use toggle bolts:

Spacing for Toggles More

Than Wall Thickness

m i Toggle Wings

I

Mounting _ _

Piate _1_

O_

Wall

Bolt End

3, Place the mounting plate against the walt and

insert the toggle wings into the holes in the wall to

mount the plate.

NOTE: Before tightening toggle bolts and wood

screw, make sure to coincide bottom line of the

Mounting plate with Horizontal line of "Rear wall

Template" and then the Mounting plate is properly

centered under the cabinet.

CAUTION: Be careful to avoid pinching fingers

between the back of the mounting plate and the wall.

4, Tighten all bolts. Pull the plate away from the wall

to help tighten the bolts.

14

Installation Instructions

B2. USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

You need to drill holes for the top support screws, a

hole large enough for the power cord to fit through,

and a cutout barge enough for the exhaust adaptor.

• Read the instructions on the TOP CABINET

TEMPLATE.

• Tape it underneath the top cabinet.

• Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes

in the cabinet bottom.

B3. ADAPTING MICROWAVE

BLOWER FOR OUTSIDE TOP

EXHAUST

1. Remove and save

screw that holds

blower plate to

microwave.

2. Lift up the

blower plate.

Biower Piate

Screw

Back of

Microwave

3. Carefully pull out the blower unit. The wires will

extend far enough to allow you to adjust the

blower unit.

CAUTION: Do not touch blade of blower to prevent

cracking and breaking. Hold outer case when the

blower is removed and re-installed.

4, Roll the blower unit 90 ° so that fan blade

openings are facing toward the top of the

microwave.

Roll

15

Installation Instructions

5. Place the blower unit back into the opening.

CAUTION: Do not pull or stretch the blower unit

wiring. Make sure the wires are not pinched.

6, Secure blower unit to microwave with the screw.

B4. INSTALLATION PROCEDURE FOR

EXHAUST ADAPTOR AND

PROPER DAMPER OPERATION

CHECK

1. Remove and save screw

from the panel-outer

ExhaustAdaptor and Damperis shipped

after being assembled to the filler-upper.

2, Slide exhaust adaptor following the instructions

show in diagram.

3, Make sure tape securing damper is removed anc

damper pivots easily before mounting microwave

4, Lift damper and Re-screw at same location as (1 '

• You will need to make adjustments to assure

proper alignment with your house exhaust duct

after the microwave is installed.

B5.__.MOUNT THE MICROWAVE OVEN

FOR EASIER INSTALLATION AND PERSONAL

SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS MICROWAVE OVEN.

IMPORTANT: Do not grip or use handle during

installation.

NOTE: If your cabinet is metal, use the nylon

grommet around the power cord hole to prevent

cutting of the cord.

NOTE: We recommend using filler blocks if the

cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used, case

damage may occur from over tightening screws.

NOTE: When mounting the microwave oven, thread

power cord through hole in bottom of top cabinet.

Keep it tight throughout Steps 1-3. Do not pinch cord

or lift oven by pulling cord.

1. Lift microwave, tilt it

forward, and hook slots

at back bottom edge

onto four lower tabs of

mounting plate.

2, Rotate front of oven up

against cabinet bottom

3. Insert a self-aligning screw through top center

cabinet hole. Temporarily secure the oven by

turning the screw at least two full turns after the

threads have engaged. (It will be completely

tightened later.) Be sure to keep power cord

tight. Be careful not to pinch the cord,

especially when mounting flush to bottom of

cabinet.

16

Installation Instructions

B5.__..MOUNT THE MICROWAVE OVEN

(cont.)

Cabinet Front

Cabinet Bottom Shelf

Filler Block

._ Equivalent to

Depth of Cabinet

Recess

Seif-Aligning Screw

Microwave Oven Top

4, Attach the microwave oven to the top cabinet.

5. Insert 2 self-aligning screws

through outer top cabinet holes.

Turn two full turns on each screw.

6, Tighten center screw

completely.

7, Tighten the outer two screws to the top of the

microwave oven. (While tightening screws, hold

the microwave oven in place against the wall and

the top cabinet.)

//

8, Install grease filters. See the Owner's Manual

packed with the microwave.

B6. ADJUST THE EXHAUST ADAPTOR

Open the top cabinet and adjust the exhaust adaptor

to connect to the house duct.

Back of

Blower-Plate Damper Microwave

For Front-to-Back

Adjustment, Slide the

Exhaust Adaptor as

Needed

B7._,.CONNECTING DUCTWORK

House Duct

1. Extend the house duct down to connect to the

exhaust adaptor.

2, Seal exhaust duct joints using duct tape.

17

Installation Instructions

C, OUTSIDE BACK EXHAUST (Horizontal Duct)

INSTALLATION OVERVIEW

C1. Prepare Rear Wall

C2. Attach Mounting Plate to Wall

C3. Prepare Top Cabinet

C4. Adjust Blower

C5. Mount the Microwave Oven

|

Clm PREPARING THE REAR WALL

FOR OUTSIDE BACK EXHAUST

You need to cut an opening in the rearwall for outside

exhaust.

• Read the instructions on the REAR WALL

TEMPLATE.

• Tape it to the rear wall.

• Cut the opening, following the instructions of the

REAR WALL TEMPLATE.

C2mATTACH THE MOUNTING PLATE

TO THE WALL

Attach the plate to the wall using toggle bolts. At least

one wood screw must be used to attach

the plate to a wall stud.

1, Remove the toggle wings from the bolts.

2, Insert the bolts into the mounting plate through

the holes designated to go into drywall and

reattach the toggle wings to 3A" onto each bolt.

18

Installation Instructions

C2.__..ATTACH THE MOUNTING PLATE

TO THE WALL (cont.)

To use toggle bolts"

Mounting

Plate

Spacing for Toggles More

Than Wall Thickness

I Toggle Wings

Belt End

3. Place the mounting plate against the wall and

insert the toggle wings into the holes in the wall to

mount the plate.

NOTE: Before tightening toggle bolts and wood

screw, make sure to coincide bottom line of the

Mounting plate with Horizontal line of "Rear wall

Template" and then the Mounting plate is properly

centered under the cabinet.

CAUTION: Be careful to avoid pinching fingers

between the back of the mounting plate and the wall.

4, Tighten all bolts. Pull the plate away from the wall

to help tighten the bolts.

C3. USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

You need to drill holes for the top support screws and

a hole large enough for the power cord to fit through.

• Read the instructions on the TOP CABINET

TEMPLATE.

• Tape it underneath the top cabinet.

• Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes in

the cabinet bottom.

C4. ADAPTING MICROWAVE BLOWER

FOR OUTSIDE BACK EXHAUST

1, Remove and save screw that holds btower Plate

to microwave.

Blower motor

screw. 2, Lift up the Blower Plate.

Blower Motor

Back of

Microwave

"_'_r..... Blower Motor

Screw

3, Carefully putt out the blower unit. The wires will

extend far enough to allow you to adjust the

blower unit.

End B

CAUTION: Do not touch blade of blower to prevent

cracking and breaking. Hold outer case when the

blower is removed and re-installed.

4, Remove "Parts "A" with Nipper or Scissors

Knockouts

Parts'A"

5. Rotate blower unit counterclockwise 180°.

Before Rotation

Back of

Microwave

After Rotation

Back of

Microwave

19

Installation Instructions

6. Place the blower unit back into the opening.

End A

End B

CAUTION: Do not pull or stretch the blower unit

wiring. Make sure the wires are not pinched.

NOTE: The blower unit exhaust openings should

match exhaust openings on rear of microwave

oven.

7, Secure the blower unit to the microwave with the

screw.

Blower-Plate

f

_ From the Mounting

Back of

Microwave Plate screw

8, Attach the exhaust adaptor to the rear of the oven

by sliding it into the guides at the top center of the

back of the oven.

Adaptor

Back of

i_ icrowave

_ Guide

Guide From Blower motor screw

(after attached the exhaust adaptor)

Push in securely until it is in the lower locking tabs.

Take care to assure that the damper hinge is installed

so that it is at the top and that the damper swings

freely.

C5. MOUNT THE MICROWAVE OVEN

FOR EASIER INSTALLATION AND PERSONAL

SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS MICROWAVE OVEN.

IMPORTANT: Do not grip or use handle during

installation.

NOTE: If your cabinet is metal, use the nylon

grommet around the power cord hole to prevent

cutting of the cord.

NOTE: We recommend using filler blocks if the

cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used, case

damage may occur from over tightening screws.

NOTE: When mounting the microwave oven, thread

power cord through hole in bottom of top cabinet.

Keep it tight throughout Steps 1-3. Do not pinch cord

or lift oven by pulling cord.

1, Lift microwave, tilt it

forward, and hook slots

at back bottom edge

onto four lower tabs of

mounting plate.

oven

up against cabinet

bottom

3, Insert a self-aligning screw through top center

cabinet hole. Temporarily secure the oven by

turning the screw at least two full turns after the

threads have engaged. (It will be completely

tightened later.) Be sure to keep power cord

tight. Be careful not to pinch the cord,

especially when mounting flush to bottom of

cabinet.

2O

Page is loading ...

Maytag JMV9169 Installation Instructions Manual

This manual is also suitable for

Maytag JMV9169 Installation Instructions Manual

in other languages

Related papers

Other documents