Grundfos PT100 Instructions Manual

Grundfos
Brand
Grundfos
Model
PT100
Type
Instructions Manual

This manual is also suitable for

grundfos INSTRUCTIONS
Pt100
Pt1000
2 3
3
PT1000
MS4”
1 2
Pt1000
MS4”
Pt100/1000
MS6”
Pt100/1000
MMS6”/8”
Pt100/1000
MMS10”
Pt100/1000
MMS12”
4 5
654
Pt1000
MS4”
Pt100/1000
MS6”
Pt100/1000
MMS6”/8”
Pt100/1000
MMS10”
Pt100/1000
MMS12”
6 7
1 3
4 2
18Nm
1 3
4 2
18Nm
1 3
4 2
18Nm
987
Pt1000
MS4”
Pt100/1000
MS6”
Pt100/1000
MMS6”/8”
Pt100/1000
MMS10”
Pt100/1000
MMS12”
8 9
1 3
4 2
50Nm
1 3
4 2
50Nm
3
Pt100/ 1000
MS6”
1 2
Pt1000
MS4”
Pt100/1000
MS6”
Pt100/1000
MMS6”/8”
Pt100/1000
MMS10”
Pt100/1000
MMS12”
10 11
7654
Pt1000
MS4”
Pt100/1000
MS6”
Pt100/1000
MMS6”/8”
Pt100/1000
MMS10”
Pt100/1000
MMS12”
12 13
2
Pt100/1000
MMS 6”/8”
1
Pt1000
MS4”
Pt100/1000
MS6”
Pt100/1000
MMS6”/8”
Pt100/1000
MMS10”
Pt100/1000
MMS12”
14 15
43
70 - 80 mm
65
Pt1000
MS4”
Pt100/1000
MS6”
Pt100/1000
MMS6”/8”
Pt100/1000
MMS10”
Pt100/1000
MMS12”
16 17
1 3
4 2
6” - 50Nm
8” - 150Nm
45°
!
9
If there is a risk of sediment build-up, suc h as sand,
around the motor, a f low sleeve sho uld be used i n
order to ensure pro per cooling o f the motor.
* At an ambient pre ssure of mini mum 1 bar (1 MPa)
5. Electrical conn ection
5.1 General
The electrical connection sh ould be carried out by an
authorised electrici an in accorda nce with loca l
regulations.
The supply volta ge, rated m aximum cur rent and
cos appear from the l oose data pl ate that must be
fitted close to the installation site.
The required volta ge quality for Grund fos MS and
MMS submersible mot ors, measured at the motor
terminals, is – 10 %/+ 6 % of t he nominal vo ltage
during continuous op eration (incl uding variatio n in
the su
pply voltage and los ses in cables ).
Furthermore, it must be chec ked that there is vol tage
symmetry in the ele ctricity sup ply lines, i .e. same
difference of vo ltage betw een the individua l phases.
See also 9. Checkin g of motor an d cable, poi nt 2.
If MS motors with a b uilt-in temper ature transmitter
(Tempcon) are not insta lled t ogether with a n MP 2 04
or similar Grundfos motor protect ion, they mus t be
connected to a 0.47 µF capacitor ap proved for
phase-phase operati on (IEC 384-1 4) to meet t he
ECEMC directive (2 004/108/EC). The capacito r
must be connected t o the two pha ses to which the
temperature transmi tter is conn ected. See fi g. 4.
Fig. 4 Connection of capac itor
The
motors are wound for direct-o n-line starting or
star-delta startin g and the st arting c urrent is betw een
4 and 6 times the ra ted current of the motor.
The run-up time of the motor is only about
0.1se cond. Direct- on-line starti ng is there fore
normally approved b y the electri city supply
authorities.
5.1.1 Frequency conv erter operati on
Three-phase MS motors can be connect ed to a
frequency converter.
If a temperature tr ansmitter is required, a Pt100
sensor for fitting t o the submer sible motor ca n be
ordered from Grundf os.
Note
In cases where t he stated liqui d
velocity cannot be a chieved, a fl ow
sleeve must be inst alled.
Motor
Installation
Flow
past the
motor
Vertical Horizontal
MS 402
MS 4000
MS 6000
0.15 m/s
40 °C
(~ 105 °F)
40 °C
(~ 105 °F)
MS 4000I*
MS 6000I*
0.15 m/s
60 °C
(~ 140 °F)
Flow sleeve
recommended
60 °C
(~ 140 °F)
Flow sleeve
recommended
MS6T30 0.15 m/s
30 °C
(~ 86 °F)
30 °C
(~ 86 °F)
MS6T60 1.0 m/ s
60 °C
(~ 140 °F)
60 °C
(~ 140 °F)
MMS
0.15 m/s
25 °C
(~ 77 °F)
25 °C
(~ 77 °F)
0.50 m/s
30 °C
(~ 86 °F)
30 °C
(~ 86 °F)
Note
For 37 kW MMS 6000, 110 kW MMS 800 0
and 170 kW MMS 1000 0, the maximu m
liquid temperature is 5 °C low er than
the values stated i n the above t able.
For 190 kW MMS 1000 0, the
temperature is 10 ° C lower.
Warning
Before starting work on the motor,
make sure that the electricity s upply
has been switched off and that it canno t
be accidentally switched on.
Warning
The motor must be earthed.
The motor must be connected to an
external mains swit ch with a mi nimum
contact gap of 3 mm in all poles .
TM00 7100 0696
Caution
If an MS motor wi th temperat ure
transmitter is connect ed to a frequency
converter, a fuse inco rporated in t he
transmitter will melt and th e transmitter
will be inactive. Th e transmitter cannot
be reactivated. This means that t he
motor will operate l ike a motor w ithout
a temperature trans mitter.
1
2
3
4
1 = L1: brown
2 = L2: black
3 = L3: grey
4 = PE: yellow/gree n
0.47 F
8
4.1.2 Grundfos MS6 and MS 6000 submersible
motors
• If the motor is delivered fr om stock, the liquid
level must be check ed before th e motor is
installed. See fig. 2.
• In the case of s ervice, th e liquid lev el must be
checked. See fig. 2.
Filling procedure:
The filling hole for mo tor liquid is p laced at the top of
the motor.
1. Posi tion the subm ersible m otor as shown i n fig . 2.
The filling scr ew must be at the highes t point of
the motor.
2. Remo ve the screw f rom the filli ng hole.
3. Inje ct liquid int o the motor wi th the fillin g syringe,
fig. 2, until the l iquid runs b ack out of the filling
hole.
4. Repl ace the screw in the fillin g hole and ti ghten
securely before cha nging the pos i
tion of the
motor.
Torque: 3.0 Nm.
The submersible mot or is now rea dy for installa tion.
Fig. 2 Motor position du ring filling – MS6 and
MS 6000
4.1.3 Grundfos MMS 6000, MM S 8000, MMS 10000
and MMS 12000 subme rsible motors
Filling procedure:
Place the motor at a 45 ° angle with the top o f the
motor upwards. See fig. 3.
5. Unsc rew the plug ( A) and place a funnel in t he
hole.
6. Pour tap water into the motor until the motor liquid
inside the motor sta rts runni ng out a t the p lug (A ).
Caution: Do not use motor liqui d as it conta ins
oil.
7. Remo ve the funnel and refit the plug (A).
The submer
sible motor is now ready for ins tallation.
Fig. 3 Motor position du ring filling – MMS
4.2 Positional r equirements
The motor can be in stalled either vertically or
horizontally.
A complete list of motor types s uitable for hor izontal
installation is sho wn in section 4.2.1.
4.2.1 Motors suitable for horizontal installation
4.3 Liquid temper atures/coolin g
The maximum liquid temperature a nd the minimu m
liquid velocity pas t the motor ap pear from the
following table.
It is recommended to insta ll the motor a bove the wel l
screen in order to achieve prope r motor cooli ng.
TM03 8129 0507
Caution
Before fitting the m otor to a pump after
a long period of storage, lub ricate the
shaft seal by adding a few drop s of
water and turning th e shaft.
45°
TM03 2065 3605
Motor type
Power output
50 Hz
Power output
60 Hz
[kW] [kW]
MS All sizes All sizes
MMS 6000 3.7 to 30 3 .7 to 30
MMS 8000 22 to 92 22 to 92
MMS 10000 75 to 170 75 to 170
MMS 12000 147 to 220 –
Caution
During operation, th e motor mus t
always be completely subm erged in the
liquid. Please cons ult the pump
manufacturer's NPSH data.
Warning
If the motor is us ed in hot li quids
(40 to 60 °C), it m ust be ensured that
persons cannot com e into con tact with
the motor and the i nstallation, e .g. by
installing a guard.
45°
A
1 3
4 2
6” - 50Nm
8” - 150Nm
45°
!
9
If there is a risk of sediment b uild-up, suc h as sand,
around the motor, a fl ow sleeve sho uld be used i n
order to ensure pro per cooling of the motor.
* At an ambient pres sure of mini mum 1 bar (1 MPa)
5. Electrical conn ection
5.1 General
The electrical connection sho uld be carried out by an
authorised electrici an in accorda nce with loca l
regulations.
The supply voltag e, rated m aximum cur rent and
cos appear from the l oose data pla te that must be
fitted close to the installation site.
The required volta ge quality for Grundf os MS and
MMS submersible moto rs, measured at the motor
terminals, is – 10 %/+ 6 % of th e nominal vo ltage
during continuous op eration (incl uding variatio n in
the su
pply voltage and loss es in cables ).
Furthermore, it must be chec ked that there is vol tage
symmetry in the ele ctricity sup ply lines, i. e. same
difference of vo ltage betw een the i ndividual phases.
See also 9. Checkin g of motor and cable, poi nt 2.
If MS motors with a bu ilt-in tempera ture transmitter
(Tempcon) are not insta lled to gether with a n MP 2 04
or similar Grundfos motor protect ion, they mus t be
connected to a 0.47 µF capacitor a pproved for
phase-phase operati on (IEC 384-1 4) to meet th e
ECEMC directive (2 004/108/EC). The capacito r
must be connected t o the two pha ses to which the
temperature transmi tter is conne cted. See fi g. 4.
Fig. 4 Connection of capacit or
The
motors are wound for direct-o n-line starting or
star-delta starting and the sta rting c urrent is betw een
4 and 6 times the ra ted current o f the motor.
The run-up time of the motor is only about
0.1se cond. Direct- on-line startin g is there fore
normally approved b y the electri city supply
authorities.
5.1.1 Frequency conv erter operati on
Three-phase MS m otors can be connecte d to a
frequency converter.
If a temperature tr ansmitter is required, a Pt100
sensor for fitting t o the submers ible motor ca n be
ordered from Grundf os.
Note
In cases where t he stated liquid
velocity cannot be a chieved, a fl ow
sleeve must be inst alled.
Motor
Installation
Flow
past the
motor
Vertical Horizontal
MS 402
MS 4000
MS 6000
0.15 m/s
40 °C
(~ 105 °F)
40 °C
(~ 105 °F)
MS 4000I*
MS 6000I*
0.15 m/s
60 °C
(~ 140 °F)
Flow sleeve
recommended
60 °C
(~ 140 °F)
Flow sleeve
recommended
MS6T30 0.15 m/s
30 °C
(~ 86 °F)
30 °C
(~ 86 °F)
MS6T60 1.0 m/s
60 °C
(~ 140 °F)
60 °C
(~ 140 °F)
MMS
0.15 m/s
25 °C
(~ 77 °F)
25 °C
(~ 77 °F)
0.50 m/s
30 °C
(~ 86 °F)
30 °C
(~ 86 °F)
Note
For 37 kW MMS 6000, 110 kW MMS 8000
and 170 kW MMS 10000 , the maximu m
liquid temperature is 5 °C low er than
the values stated in the above ta ble.
For 190 kW MMS 1000 0, the
temperature is 10 ° C lower.
Warning
Before starting work on the m otor,
make sure that the electricity s upply
has been switched off and that it canno t
be accidentally switched on.
Warning
The motor must be earthed.
The motor must be connected to an
external mains swit ch with a min imum
contact gap of 3 mm in all poles.
TM00 7100 0696
Caution
If an MS motor wi th temperat ure
transmitter is connect ed to a frequency
converter, a fuse inco rporated in t he
transmitter will melt and th e transmitter
will be inactive. Th e transmitter cannot
be reactivated. This means that t he
motor will operate l ike a motor w ithout
a temperature trans mitter.
1
2
3
4
1 = L1: brown
2 = L2: black
3 = L3: grey
4 = PE: yellow/gree n
0.47 F
8
4.1.2 Grundfos MS6 a nd MS 6000 submersible
motors
• If the motor is delivered fr om stock, the liquid
level must be check ed before the motor is
installed. See fig. 2.
• In the case of s ervice, the liquid lev el must be
checked. See fig. 2.
Filling procedure:
The filling hole for mo tor liquid is p laced at the top of
the motor.
1. Posit ion the subme rsible m otor as s hown i n fig . 2.
The filling scre w must be at the highes t point of
the motor.
2. Remov e the screw f rom the filli ng hole.
3. Injec t liquid into the motor wi th the fillin g syringe,
fig. 2, until the l iquid runs ba ck out of the filling
hole.
4. Repla ce the screw in the fillin g hole and ti ghten
securely before cha nging the
posi
tion of the
motor.
Torque: 3.0 Nm.
The submersible mot or is now read y for installa tion.
Fig. 2 Motor position duri ng filling – M S6 and
MS 6000
4.1.3 Grundfos MMS 6000, MM S 8000, MMS 10000
and MMS 12000 subme rsible motors
Filling procedure:
Place the motor at a 45 ° angle w ith the top o f the
motor upwards. See fig. 3.
5. Unscr ew the plug ( A) and place a funnel in t he
hole.
6. Pour tap water into the mo tor until the mo tor liquid
inside the motor sta rts runni ng out a t the p lug (A ).
Caution: Do not use motor liqui d as it contai ns
oil.
7. Remov e the funnel and refit the plug (A).
The subm
er
sible motor is now ready for insta llation.
Fig. 3 Motor position duri ng filling – M MS
4.2 Positional r equirements
The motor can be in stalled either vertically or
horizontally.
A complete list of motor types su itable for hor izontal
installation is show n in section 4.2.1.
4.2.1 Motors suitable for horizontal installation
4.3 Liquid temper atures/coolin g
The maximum liquid temperature a nd the minimu m
liquid velocity past the motor ap pear from the
following table.
It is recommended to instal l the motor a bove the wel l
screen in order to achieve proper motor coolin g.
TM03 8129 0507
Caution
Before fitting the m otor to a pump after
a long period of s torage, lub ricate the
shaft seal by adding a few drop s of
water and turning th e shaft.
45°
TM03 2065 3605
Motor type
Power output
50 Hz
Power output
60 Hz
[kW] [kW]
MS All sizes Al l sizes
MMS 6000 3.7 to 30 3.7 to 3 0
MMS 8000 22 to 92 22 to 92
MMS 10000 75 to 170 75 to 170
MMS 12000 147 to 220 –
Caution
During operation, th e motor mus t
always be completely subm erged in the
liquid. Please consu lt the pump
manufacturer's NPSH data.
Warning
If the motor is us ed in hot li quids
(40 to 60 °C), it m ust be ensured that
persons cannot com e into con tact with
the motor and the in stallation, e .g. by
installing a guard.
45°
A
1 3
4 2
6” - 50Nm
8” - 150Nm
45°
!
9
If there is a risk of sediment b uild-up, suc h as sand,
around the motor, a fl ow sleeve sho uld be used i n
order to ensure pro per cooling of the motor.
* At an ambient pres sure of mini mum 1 bar (1 MPa)
5. Electrical conn ection
5.1 General
The electrical connection sho uld be carried out by an
authorised electrici an in accorda nce with loca l
regulations.
The supply voltag e, rated m aximum cur rent and
cos appear from the l oose data pla te that must be
fitted close to the installation site.
The required volta ge quality for Grundf os MS and
MMS submersible moto rs, measured at the motor
terminals, is – 10 %/+ 6 % of th e nominal vo ltage
during continuous op eration (incl uding variatio n in
the su
pply voltage and loss es in cables ).
Furthermore, it must be chec ked that there is vol tage
symmetry in the ele ctricity sup ply lines, i. e. same
difference of vo ltage betw een the i ndividual phases.
See also 9. Checkin g of motor and cable, poi nt 2.
If MS motors with a bu ilt-in tempera ture transmitter
(Tempcon) are not insta lled to gether with a n MP 2 04
or similar Grundfos motor protect ion, they mus t be
connected to a 0.47 µF capacitor a pproved for
phase-phase operati on (IEC 384-1 4) to meet th e
ECEMC directive (2 004/108/EC). The capacito r
must be connected t o the two pha ses to which the
temperature transmi tter is conne cted. See fi g. 4.
Fig. 4 Connection of capacit or
The
motors are wound for direct-o n-line starting or
star-delta starting and the sta rting c urrent is betw een
4 and 6 times the ra ted current o f the motor.
The run-up time of the motor is only about
0.1se cond. Direct- on-line startin g is there fore
normally approved b y the electri city supply
authorities.
5.1.1 Frequency conv erter operati on
Three-phase MS m otors can be connecte d to a
frequency converter.
If a temperature tr ansmitter is required, a Pt100
sensor for fitting t o the submers ible motor ca n be
ordered from Grundf os.
Note
In cases where t he stated liquid
velocity cannot be a chieved, a fl ow
sleeve must be inst alled.
Motor
Installation
Flow
past the
motor
Vertical Horizontal
MS 402
MS 4000
MS 6000
0.15 m/s
40 °C
(~ 105 °F)
40 °C
(~ 105 °F)
MS 4000I*
MS 6000I*
0.15 m/s
60 °C
(~ 140 °F)
Flow sleeve
recommended
60 °C
(~ 140 °F)
Flow sleeve
recommended
MS6T30 0.15 m/s
30 °C
(~ 86 °F)
30 °C
(~ 86 °F)
MS6T60 1.0 m/s
60 °C
(~ 140 °F)
60 °C
(~ 140 °F)
MMS
0.15 m/s
25 °C
(~ 77 °F)
25 °C
(~ 77 °F)
0.50 m/s
30 °C
(~ 86 °F)
30 °C
(~ 86 °F)
Note
For 37 kW MMS 6000, 110 kW MMS 8000
and 170 kW MMS 10000 , the maximu m
liquid temperature is 5 °C low er than
the values stated in the above ta ble.
For 190 kW MMS 1000 0, the
temperature is 10 ° C lower.
Warning
Before starting work on the m otor,
make sure that the electricity s upply
has been switched off and that it canno t
be accidentally switched on.
Warning
The motor must be earthed.
The motor must be connected to an
external mains swit ch with a min imum
contact gap of 3 mm in all poles.
TM00 7100 0696
Caution
If an MS motor wi th temperat ure
transmitter is connect ed to a frequency
converter, a fuse inco rporated in t he
transmitter will melt and th e transmitter
will be inactive. Th e transmitter cannot
be reactivated. This means that t he
motor will operate l ike a motor w ithout
a temperature trans mitter.
1
2
3
4
1 = L1: brown
2 = L2: black
3 = L3: grey
4 = PE: yellow/gree n
0.47 F
8
4.1.2 Grundfos MS6 a nd MS 6000 submersible
motors
• If the motor is delivered fr om stock, the liquid
level must be check ed before the motor is
installed. See fig. 2.
• In the case of s ervice, the liquid lev el must be
checked. See fig. 2.
Filling procedure:
The filling hole for mo tor liquid is p laced at the top of
the motor.
1. Posit ion the subme rsible m otor as s hown i n fig . 2.
The filling scre w must be at the highes t point of
the motor.
2. Remov e the screw f rom the filli ng hole.
3. Injec t liquid into the motor wi th the fillin g syringe,
fig. 2, until the l iquid runs ba ck out of the filling
hole.
4. Repla ce the screw in the fillin g hole and ti ghten
securely before cha nging the
posi
tion of the
motor.
Torque: 3.0 Nm.
The submersible mot or is now read y for installa tion.
Fig. 2 Motor position duri ng filling – M S6 and
MS 6000
4.1.3 Grundfos MMS 6000, MM S 8000, MMS 10000
and MMS 12000 subme rsible motors
Filling procedure:
Place the motor at a 45 ° angle w ith the top o f the
motor upwards. See fig. 3.
5. Unscr ew the plug ( A) and place a funnel in t he
hole.
6. Pour tap water into the mo tor until the mo tor liquid
inside the motor sta rts runni ng out a t the p lug (A ).
Caution: Do not use motor liqui d as it contai ns
oil.
7. Remov e the funnel and refit the plug (A).
The subm
er
sible motor is now ready for insta llation.
Fig. 3 Motor position duri ng filling – M MS
4.2 Positional r equirements
The motor can be in stalled either vertically or
horizontally.
A complete list of motor types su itable for hor izontal
installation is show n in section 4.2.1.
4.2.1 Motors suitable for horizontal installation
4.3 Liquid temper atures/coolin g
The maximum liquid temperature a nd the minimu m
liquid velocity past the motor ap pear from the
following table.
It is recommended to instal l the motor a bove the wel l
screen in order to achieve proper motor coolin g.
TM03 8129 0507
Caution
Before fitting the m otor to a pump after
a long period of s torage, lub ricate the
shaft seal by adding a few drop s of
water and turning th e shaft.
45°
TM03 2065 3605
Motor type
Power output
50 Hz
Power output
60 Hz
[kW] [kW]
MS All sizes Al l sizes
MMS 6000 3.7 to 30 3.7 to 3 0
MMS 8000 22 to 92 22 to 92
MMS 10000 75 to 170 75 to 170
MMS 12000 147 to 220 –
Caution
During operation, th e motor mus t
always be completely subm erged in the
liquid. Please consu lt the pump
manufacturer's NPSH data.
Warning
If the motor is us ed in hot li quids
(40 to 60 °C), it m ust be ensured that
persons cannot com e into con tact with
the motor and the in stallation, e .g. by
installing a guard.
45°
A
987
Pt1000
MS4”
Pt100/1000
MS6”
Pt100/1000
MMS6”/8”
Pt100/1000
MMS10”
Pt100/1000
MMS12”
18 19
2
Pt100/1000
MMS10”
1
Pt1000
MS4”
Pt100/1000
MS6”
Pt100/1000
MMS6”/8”
Pt100/1000
MMS10”
Pt100/1000
MMS12”
20 21
3 mm
100mm
3 54
Pt1000
MS4”
Pt100/1000
MS6”
Pt100/1000
MMS6”/8”
Pt100/1000
MMS10”
Pt100/1000
MMS12”
22 23
1 3
4 2
280Nm
45°
!
9
If there is a risk of sediment build-up, su ch as sand,
around the motor, a flow sleeve s hould be used in
order to ensure pr oper cooling of the motor.
* At an ambient pr essure of min imum 1 bar ( 1 MPa)
5. Electrical con nection
5.1 General
The electrical connectio n should be carried out by an
authorised electri cian in accord ance with loc al
regulations.
The supply vol tage, rated maximum cu rrent and
cos appear from th e loose data plate that must be
fitted close to t he installatio n site.
The required vol tage qualit y for Grun dfos MS and
MMS submersible mo tors, measure d at the motor
terminals, is – 1 0 %/+ 6 % of the nominal v oltage
during continuous operation (inc luding variat ion in
the sup
ply voltage and los ses in cables ).
Furthermore, it must be ch ecked that there is voltage
symmetry in the el ectricity su pply lines, i.e. same
difference of v oltage bet ween the individua l phases .
See also 9. Checki ng of motor a nd cable, po int 2.
If MS motors with a built-in tempe rature transmitte r
(Tempcon) are not inst alled t ogethe r with an MP 204
or similar Grundfo s motor protec tion, they mu st be
connected to a 0. 47 µF capacitor app roved for
phase-phase operat ion (IEC 384 -14) to meet the
ECEM C directive ( 2004/108/EC) . The capacit or
must be connected to the two p hases to which the
temperature trans mitter is con nected. See f ig. 4.
Fig. 4 Connection of capacitor
The
motors are wound for direct-o n-line starting or
star-delta startin g and the s tarting curren t is bet ween
4 and 6 times the rated current of the motor.
The run-up tim e of the moto r is only abou t
0.1s econd. Direct -on-line start ing is ther efore
normally approved by the electr icity supply
authorities.
5.1.1 Frequency con verter operat ion
Three-phase MS motors can be connec ted to a
frequency converte r.
If a temperature transmitter i s required, a Pt100
sensor for fitting to the subme rsible motor can be
ordered from Grund fos.
Note
In cases where the stated liq uid
velocity cannot be achieved, a f low
sleeve must be ins talled.
Motor
Installation
Flow
past the
motor
Vertical Horizonta l
MS 402
MS 4000
MS 6000
0.15 m/s
40 °C
(~ 105 °F)
40 °C
(~ 105 °F)
MS 4000I*
MS 6000I*
0.15 m/s
60 °C
(~ 140 °F)
Flow sleeve
recommended
60 °C
(~ 140 °F)
Flow sleeve
recommended
MS6T30 0.15 m/s
30 °C
(~ 86 °F)
30 °C
(~ 86 °F)
MS6T60 1.0 m/s
60 °C
(~ 140 °F)
60 °C
(~ 140 °F)
MMS
0.15 m/s
25 °C
(~ 77 °F)
25 °C
(~ 77 °F)
0.50 m/s
30 °C
(~ 86 °F)
30 °C
(~ 86 °F)
Note
For 37 kW MMS 6000, 110 kW MMS 80 00
and 170 kW MMS 100 00, the maxim um
liquid temperatur e is 5 °C lo wer than
the values stated in the above table.
For 190 kW MMS 100 00, the
temperature is 10 °C lower.
Warning
Before startin g work on the motor,
make sure that the electricity supply
has been switched off and that it cann ot
be accidentally switched on.
Warning
The motor must b e earthed.
The motor must b e connecte d to an
external mains sw itch with a m inimum
contact gap of 3 m m in all pole s.
Caution
If an MS motor w ith tempera ture
transmitter is connec ted to a frequenc y
converter, a fuse inc orporated in the
transmitter will melt and the transmitter
will be inactive. The transmitte r cannot
be reactivated. Th is means that the
motor will operate like a motor without
a temperature tran smitter.
1
2
3
4
1 = L1: brown
2 = L2: black
3 = L3: grey
4 = PE: yellow/gre en
0.47 F
8
4.1.2 Grundfos MS6 and MS 6000 submersible
motors
• If the motor i s delivered from stock, th e liquid
level must be che cked before t he motor is
installed. See fig. 2.
• In the case of service, t he liquid le vel must b e
checked. See fig. 2.
Filling procedure:
The filling hole for m otor liquid is p laced at th e top of
the motor.
1. Pos ition the subm ersible motor as shown in fi g. 2.
The filling sc rew must be at the highe st point of
the motor.
2. Rem ove the screw from the fill ing hole.
3. Inj ect liquid in to the motor w ith the filli ng syringe,
fig. 2, until the liquid runs back out of th e filling
hole.
4. Rep lace the scre w in the filli ng hole and t ighten
securely before ch anging the po si
tion of the
motor.
Torque: 3.0 Nm.
The submersible mo tor is now re ady for instal lation.
Fig. 2 Motor positio n during fill ing – MS6 and
MS 6000
4.1.3 Grundfos MMS 6000, MMS 8000, MMS 10000
and MMS 12000 subm ersible motor s
Filling procedure:
Place the motor at a 45 ° angle with the top of the
motor upwards. See fig. 3.
5. Uns crew the plug (A) and place a funnel in the
hole.
6. Pou r tap water into the motor until the motor liquid
inside the motor st arts runn ing out at the p lug (A ).
Caution: Do not us e motor liqu id as it con tains
oil.
7. Rem ove the funne l and refit th e plug (A).
The submer
sible motor is now ready for in stallation.
Fig. 3 Motor positio n during fill ing – MMS
4.2 Positional requirements
The motor can be i nstalled eithe r vertically or
horizontally.
A complete list of motor types suitable for h orizontal
installation is sh own in sectio n 4.2.1.
4.2.1 Motors suitabl e for horizon tal installation
4.3 Liquid tempe ratures/cooli ng
The maximum liqui d temperature and the minim um
liquid velocity pa st the motor a ppear from th e
following table.
It is recommended to insta ll the motor above the we ll
screen in order to achieve prop er motor cool ing.
TM03 8129 0507
Caution
Before fitting the motor to a pump after
a long period of storage, lu bricate the
shaft seal by addin g a few dro ps of
water and turning t he shaft.
45°
TM03 2065 3605
Motor type
Power output
50 Hz
Power output
60 Hz
[kW] [kW]
MS All sizes All sizes
MMS 6000 3.7 to 30 3.7 to 30
MMS 8000 22 to 92 22 to 92
MMS 10000 75 to 1 70 75 to 170
MMS 12000 147 to 220 –
Caution
During operation, t he motor mu st
always be completely sub merged in the
liquid. Please con sult the pump
manufacturer's NPS H data.
Warning
If the motor is used in hot l iquids
(40 to 60 °C), it must be ensured tha t
persons cannot co me into co ntact with
the motor and the installation, e.g. by
installing a guard .
45°
A
1 3
4 2
280Nm
45°
!
9
If there is a risk o f sediment b uild-up, such as sand,
around the motor, a fl ow sleeve shou ld be used in
order to ensure prop er cooling of the motor.
* At an ambient pres sure of minim um 1 bar (1 MPa)
5. Electrical conne ction
5.1 General
The electrical connection sho uld be carried out by an
authorised electricia n in accordan ce with local
regulations.
The supply voltag e, rated m aximum cur rent and
cos appear from the loose d ata plate th at must be
fitted close to the installation site.
The required voltag e quality for Grundf os MS and
MMS submersible motor s, measured a t the motor
terminals, is – 10 % /+ 6 % of th e nominal vol tage
during continuous ope ration (inclu ding variation in
the su
pply voltage and loss es in cables) .
Furthermore, it must be chec ked that there is volta ge
symmetry in the elec tricity supp ly lines, i.e . same
difference of vol tage betw een the i ndividual phases.
See also 9. Checking of motor and cable, poin t 2.
If MS motors with a bu ilt-in temperat ure transmitter
(Tempcon) are not insta lled to gether with a n MP 2 04
or similar Grundfos m otor protecti on, they must be
connected to a 0.47 µF capacitor appro ved for
phase-phase operatio n (IEC 384-14 ) to meet the
ECEMC directive (20 04/108/EC). The capacito r
must be connected to the two phas es to which t he
temperature transmit ter is conne cted. See fig . 4.
Fig. 4 Connection of capacitor
The
motors are wound for direct-on -line starting or
star-delta starting and the sta rting c urrent is betwe en
4 and 6 times the rat ed current o f the motor.
The run-up time of the motor is only about
0.1sec ond. Direct-o n-line startin g is theref ore
normally approved by the electric ity supply
authorities.
5.1.1 Frequency conve rter operatio n
Three-phase MS m otors can be connected to a
frequency converter.
If a temperature tra nsmitter is required, a P t100
sensor for fitting to the submersi ble motor can be
ordered from Grundfo s.
Note
In cases where th e stated liquid
velocity cannot be ac hieved, a flo w
sleeve must be insta lled.
Motor
Installation
Flow
past the
motor
Vertical Horizontal
MS 402
MS 4000
MS 6000
0.15 m/s
40 °C
(~ 105 °F)
40 °C
(~ 105 °F)
MS 4000I*
MS 6000I*
0.15 m/s
60 °C
(~ 140 °F)
Flow sleeve
recommended
60 °C
(~ 140 °F)
Flow sleeve
recommended
MS6T30 0.15 m/s
30 °C
(~ 86 °F)
30 °C
(~ 86 °F)
MS6T60 1.0 m/s
60 °C
(~ 140 °F)
60 °C
(~ 140 °F)
MMS
0.15 m/s
25 °C
(~ 77 °F)
25 °C
(~ 77 °F)
0.50 m/s
30 °C
(~ 86 °F)
30 °C
(~ 86 °F)
Note
For 37 kW MMS 6000, 110 kW MMS 8000
and 170 kW MMS 10000 , the maximum
liquid temperature is 5 °C lowe r than
the values stated in the above tab le.
For 190 kW MMS 10000 , the
temperature is 10 °C lower.
Warning
Before starting w ork on the m otor,
make sure that the e lectricity su pply
has been switched off and that it cannot
be accidentally sw itched on.
Warning
The motor must be earthed.
The motor must be connected t o an
external mains switc h with a min imum
contact gap of 3 mm in all poles.
Caution
If an MS motor wit h temperatur e
transmitter is connecte d to a frequency
converter, a fuse incor porated in th e
transmitter will melt and the transmitter
will be inactive. The transmitter cannot
be reactivated. This means that th e
motor will operate li ke a motor wi thout
a temperature transm itter.
1
2
3
4
1 = L1: brown
2 = L2: black
3 = L3: grey
4 = PE: yellow/green
0.47 F
8
4.1.2 Grundfos MS6 a nd MS 6000 s ubmersible
motors
• If the motor is d elivered fro m stock, the liquid
level must be checke d before the motor is
installed. See f ig. 2.
• In the case of se rvice, the liquid lev el must be
checked. See fig. 2 .
Filling procedure:
The filling hole for mot or liquid is pl aced at the t op of
the motor.
1. Posit ion the subme rsible mo tor as s hown i n fig . 2.
The filling scre w must be a t the highest point of
the motor.
2. Remov e the screw fr om the fillin g hole.
3. Injec t liquid into the motor wit h the filling syringe,
fig. 2, until the li quid runs ba ck out of the f illing
hole.
4. Repla ce the screw i n the filling hole and tig hten
securely before chan ging the posi
tion of the
motor.
Torque: 3.0 Nm.
The submersible moto r is now read y for installat ion.
Fig. 2 Motor position during filling – MS6 and
MS 6000
4.1.3 Grundfos MMS 6000, MMS 8000, MMS 10000
and MMS 12000 submer sible motors
Filling procedure:
Place the motor at a 45 ° angle w ith the top of the
motor upwards. See f ig. 3.
5. Unscr ew the plug (A ) and place a funnel in th e
hole.
6. Pour tap wa ter into the mo tor until the mo tor liquid
inside the motor star ts runnin g out at the pl ug (A) .
Caution: Do not use motor liquid as it contai ns
oil.
7. Remov e the funnel a nd refit the plug (A).
The submer
sible motor is now r eady for insta llation.
Fig. 3 Motor position during filling – MMS
4.2 Positional re quirements
The motor can be ins talled either vertically or
horizontally.
A complete list of m otor types su itable for hori zontal
installation is show n in section 4.2.1.
4.2.1 Motors suitable for horizontal installation
4.3 Liquid tempera tures/cooling
The maximum liquid temperature an d the minimum
liquid velocity past the motor app ear from the
following table.
It is recommended to instal l the motor a bove the wel l
screen in order to a chieve proper motor coolin g.
TM03 8129 0507
Caution
Before fitting the mo tor to a pump a fter
a long period of st orage, lubr icate the
shaft seal by adding a few drops of
water and turning the shaft.
45°
TM03 2065 3605
Motor type
Power output
50 Hz
Power output
60 Hz
[kW] [kW]
MS All sizes All si zes
MMS 6000 3.7 to 30 3.7 to 30
MMS 8000 22 to 92 22 to 9 2
MMS 10000 75 to 170 75 to 170
MMS 12000 147 to 220 –
Caution
During operation, the motor must
always be completely subme rged in the
liquid. Please consu lt the pump
manufacturer's NPSH data.
Warning
If the motor is use d in hot liq uids
(40 to 60 °C), it mu st be ensured that
persons cannot come into cont act with
the motor and the in stallation, e. g. by
installing a guard.
45°
A
7 86
Pt1000
MS4”
Pt100/1000
MS6”
Pt100/1000
MMS6”/8”
Pt100/1000
MMS10”
Pt100/1000
MMS12”
24 25
MMS12”
Pt100
x
MMS12”
Pt100
x
2
Pt100/1000
MMS12”
1
Pt1000
MS4”
Pt100/1000
MS6”
Pt100/1000
MMS6”/8”
Pt100/1000
MMS10”
Pt100/1000
MMS12”
26 27
MMS12”
Pt100
x
3 mm
x-10mm
43
Pt1000
MS4”
Pt100/1000
MS6”
Pt100/1000
MMS6”/8”
Pt100/1000
MMS10”
Pt100/1000
MMS12”
28 29
6 75
Pt1000
MS4”
Pt100/1000
MS6”
Pt100/1000
MMS6”/8”
Pt100/1000
MMS10”
Pt100/1000
MMS12”
30 31
1 3
4 2
280Nm
45°
!
If there is a risk of sediment build-up, su ch as sand,
around the motor, a f low sleeve sh ould be used in
order to ensure pr oper cooling o f the motor.
* At an ambient pre ssure of min imum 1 bar ( 1 MPa)
5. Electrical con nection
5.1 General
The electrical connection should be carried out by an
authorised electric ian in accord ance with loc al
regulations.
The supply volta ge, rated maximum cu rrent and
cos appear from the loose data p late that must be
fitted close to th e installation site.
The required vol tage quality for Grund fos MS and
MMS submersible mot ors, measured at the motor
terminals, is – 10 %/+ 6 % of t he nominal v oltage
during continuous o peration (inc luding variati on in
the sup
ply voltage and loss es in cables ).
Furthermore, it must be che cked that there is vo ltage
symmetry in the el ectricity su pply lines, i.e. same
difference of v oltage bet ween the individua l phases.
See also 9. Checki ng of motor an d cable, po int 2.
If MS motors with a b uilt-in tempe rature transmitte r
(Tempcon) are not insta lled t ogethe r with an MP 2 04
or similar Grundfos motor protec tion, they mu st be
connected to a 0.4 7 µF capacitor app roved for
phase-phase operat ion (IEC 384- 14) to meet t he
ECEM C directive ( 2004/108/EC). The capacit or
must be connected to the two ph ases to which the
temperature transm itter is con nected. See f ig. 4.
Fig. 4 Connection of ca pacitor
The
motors are wound for direct-on -line starting or
star-delta startin g and the st arting current is betw een
4 and 6 times the r ated current of the motor.
The run-up time of the motor is only abou t
0.1s econd. Direct -on-line starti ng is there fore
normally approved by the electr icity supply
authorities.
5.1.1 Frequency con verter operat ion
Three-phase MS motors can be connec ted to a
frequency converte r.
If a temperature t ransmitter is required, a Pt100
sensor for fitting to the submer sible motor c an be
ordered from Grund fos.
Note
In cases where the stated liqu id
velocity cannot be achieved, a f low
sleeve must be ins talled.
Motor
Installation
Flow
past the
motor
Vertical Horizontal
MS 402
MS 4000
MS 6000
0.15 m/s
40 °C
(~ 105 °F)
40 °C
(~ 105 °F)
MS 4000I*
MS 6000I*
0.15 m/s
60 °C
(~ 140 °F)
Flow sleeve
recommended
60 °C
(~ 140 °F)
Flow sleeve
recommended
MS6T30 0.15 m/s
30 °C
(~ 86 °F)
30 °C
(~ 86 °F)
MS6T60 1. 0 m/s
60 °C
(~ 140 °F)
60 °C
(~ 140 °F)
MMS
0.15 m/s
25 °C
(~ 77 °F)
25 °C
(~ 77 °F)
0.50 m/s
30 °C
(~ 86 °F)
30 °C
(~ 86 °F)
Note
For 37 kW MMS 6000, 110 kW MMS 800 0
and 170 kW MMS 1000 0, the maxim um
liquid temperatur e is 5 °C lo wer than
the values stated in the above t able.
For 190 kW MMS 100 00, the
temperature is 10 °C lower.
Warning
Before starting work on the motor,
make sure that the electricity supply
has been switched off and that it cann ot
be accidentally switched on.
Warning
The motor must b e earthed.
The motor must be connected to an
external mains swi tch with a mi nimum
contact gap of 3 m m in all poles .
Caution
If an MS motor w ith temperat ure
transmitter is connec ted to a frequency
converter, a fuse inc orporated in t he
transmitter will melt and the transmitter
will be inactive. T he transmitte r cannot
be reactivated. Thi s means that the
motor will operate like a motor without
a temperature trans mitter.
1
2
3
4
1 = L1: brown
2 = L2: black
3 = L3: grey
4 = PE: yellow/gre en
0.47 F
8
4.1.2 Grundfos MS6 and MS 6000 submersible
motors
• If the motor is delivered f rom stock, th e liquid
level must be chec ked before th e motor is
installed. See fig. 2.
• In the case of service, t he liquid le vel must be
checked. See fig. 2.
Filling procedure:
The filling hole for m otor liquid is p laced at the top of
the motor.
1. Posi tion the subm ersible m otor as shown i n fi g. 2.
The filling scr ew must be at the highe st point of
the motor.
2. Remo ve the screw from the fill ing hole.
3. Inje ct liquid int o the motor w ith the filli ng syringe,
fig. 2, until the liquid runs b ack out of the filling
hole.
4. Repl ace the screw in the filli ng hole and t ighten
securely before ch anging the pos i
tion of the
motor.
Torque: 3.0 Nm.
The submersible mo tor is now rea dy for install ation.
Fig. 2 Motor position during fillin g – MS6 and
MS 6000
4.1.3 Grundfos MMS 6000, MMS 8000, MMS 10000
and MMS 12000 subm ersible motors
Filling procedure:
Place the motor at a 45 ° angle with the top of the
motor upwards. See fig. 3.
5. Unsc rew the plug (A) and place a funnel in the
hole.
6. Pour tap water into the motor until the motor liquid
inside the motor sta rts runn ing out a t the p lug (A ).
Caution: Do not us e motor liqu id as it conta ins
oil.
7. Remo ve the funnel and refit th e plug (A).
The submer
sible motor is now ready for ins tallation.
Fig. 3 Motor position during fillin g – MMS
4.2 Positional requirements
The motor can be i nstalled either vertically o r
horizontally.
A complete list of motor types s uitable for ho rizontal
installation is sho wn in section 4.2.1.
4.2.1 Motors suitabl e for horizonta l installation
4.3 Liquid tempe ratures/cooli ng
The maximum liqui d temperature and the minim um
liquid velocity pas t the motor a ppear from th e
following table.
It is recommended to insta ll the motor above the we ll
screen in order to achieve prop er motor cooli ng.
TM03 8129 0507
Caution
Before fitting the motor to a pump after
a long period of storage, lub ricate the
shaft seal by addin g a few dro ps of
water and turning t he shaft.
45°
TM03 2065 3605
Motor type
Power output
50 Hz
Power output
60 Hz
[kW] [kW]
MS All sizes All sizes
MMS 6000 3.7 to 30 3.7 to 30
MMS 8000 22 to 92 22 t o 92
MMS 10000 75 to 170 75 to 170
MMS 12000 147 to 220 –
Caution
During operation, t he motor mu st
always be completely sub merged in the
liquid. Please con sult the pump
manufacturer's NPS H data.
Warning
If the motor is u sed in hot l iquids
(40 to 60 °C), it must b e ensured that
persons cannot co me into con tact with
the motor and the i nstallation, e.g. by
installing a guard.
45°
A
1 3
4 2
280Nm
45°
!
If there is a risk o f sediment b uild-up, such as sand,
around the motor, a fl ow sleeve shou ld be used in
order to ensure prop er cooling of the motor.
* At an ambient pres sure of minim um 1 bar (1 MPa)
5. Electrical conne ction
5.1 General
The electrical connection sho uld be carried out by an
authorised electricia n in accordan ce with local
regulations.
The supply voltag e, rated m aximum cur rent and
cos appear from the loose d ata plate th at must be
fitted close to the installation site.
The required voltag e quality for Grundf os MS and
MMS submersible motor s, measured a t the motor
terminals, is – 10 % /+ 6 % of th e nominal vol tage
during continuous ope ration (inclu ding variation in
the sup
ply voltage and losses in cables).
Furthermore, it must be chec ked that there is volta ge
symmetry in the elec tricity supp ly lines, i.e . same
difference of vol tage betw een the i ndividual phases.
See also 9. Checking of motor and cable, poin t 2.
If MS motors with a bu ilt-in temperat ure transmitter
(Tempcon) are not insta lled to gether with a n MP 2 04
or similar Grundfos m otor protecti on, they must be
connected to a 0.47 µF capacitor appro ved for
phase-phase operatio n (IEC 384-14 ) to meet the
ECEMC directive (20 04/108/EC). The capacito r
must be connected to the two phas es to which t he
temperature transmit ter is conne cted. See fig . 4.
Fig. 4 Connection of capacitor
The
motors are wound for direct-on- line starting or
star-delta starting and the sta rting c urrent is betwe en
4 and 6 times the rat ed current o f the motor.
The run-up time of the motor is only about
0.1sec ond. Direct-o n-line startin g is theref ore
normally approved by the electric ity supply
authorities.
5.1.1 Frequency conve rter operatio n
Three-phase MS m otors can be connected to a
frequency converter.
If a temperature tra nsmitter is required, a P t100
sensor for fitting to the submersi ble motor can be
ordered from Grundfo s.
Note
In cases where th e stated liquid
velocity cannot be ac hieved, a flo w
sleeve must be insta lled.
Motor
Installation
Flow
past the
motor
Vertical Horizontal
MS 402
MS 4000
MS 6000
0.15 m/s
40 °C
(~ 105 °F)
40 °C
(~ 105 °F)
MS 4000I*
MS 6000I*
0.15 m/s
60 °C
(~ 140 °F)
Flow sleeve
recommended
60 °C
(~ 140 °F)
Flow sleeve
recommended
MS6T30 0.15 m/s
30 °C
(~ 86 °F)
30 °C
(~ 86 °F)
MS6T60 1.0 m/s
60 °C
(~ 140 °F)
60 °C
(~ 140 °F)
MMS
0.15 m/s
25 °C
(~ 77 °F)
25 °C
(~ 77 °F)
0.50 m/s
30 °C
(~ 86 °F)
30 °C
(~ 86 °F)
Note
For 37 kW MMS 6000, 110 kW MMS 8000
and 170 kW MMS 10000 , the maximum
liquid temperature is 5 °C lowe r than
the values stated in the above tab le.
For 190 kW MMS 10000 , the
temperature is 10 °C lower.
Warning
Before starting w ork on the m otor,
make sure that the e lectricity su pply
has been switched off and that it cannot
be accidentally s witched on.
Warning
The motor must be earthed.
The motor must be connected t o an
external mains switc h with a min imum
contact gap of 3 mm in all poles.
Caution
If an MS motor wit h temperatu re
transmitter is connecte d to a frequency
converter, a fuse incor porated in th e
transmitter will melt and the transmitter
will be inactive. The transmitter cannot
be reactivated. This means that th e
motor will operate li ke a motor wi thout
a temperature transm itter.
1
2
3
4
1 = L1: brown
2 = L2: black
3 = L3: grey
4 = PE: yellow/green
0.47 F
8
4.1.2 Grundfos MS6 a nd MS 6000 s ubmersible
motors
• If the motor is d elivered fro m stock, the liquid
level must be checke d before the motor is
installed. See f ig. 2.
• In the case of se rvice, the liquid lev el must be
checked. See fig. 2 .
Filling procedure:
The filling hole for mot or liquid is pl aced at the t op of
the motor.
1. Posit ion the subme rsible mo tor as s hown i n fig . 2.
The filling scre w must be a t the highest point of
the motor.
2. Remov e the screw fr om the fillin g hole.
3. Injec t liquid into the motor wit h the filling syringe,
fig. 2, until the li quid runs ba ck out of the f illing
hole.
4. Repla ce the screw i n the filling hole and tig hten
securely before chan ging the posi
tion of the
motor.
Torque: 3.0 Nm.
The submersible moto r is now read y for installat ion.
Fig. 2 Motor position during filling – MS6 and
MS 6000
4.1.3 Grundfos MMS 6000, MMS 8000, MMS 10000
and MMS 12000 submer sible motors
Filling procedure:
Place the motor at a 45 ° angle w ith the top of the
motor upwards. See f ig. 3.
5. Unscr ew the plug (A ) and place a funnel in th e
hole.
6. Pour tap wa ter into the mo tor until the mo tor liquid
inside the motor star ts runnin g out at the pl ug (A) .
Caution: Do not use motor liquid as it contai ns
oil.
7. Remov e the funnel a nd refit the plug (A).
The submer
sible motor is now r eady for insta llation.
Fig. 3 Motor position during filling – MMS
4.2 Positional re quirements
The motor can be ins talled either vertically or
horizontally.
A complete list of m otor types su itable for hori zontal
installation is show n in section 4.2.1.
4.2.1 Motors suitable for horizontal installation
4.3 Liquid tempera tures/cooling
The maximum liquid temperature an d the minimum
liquid velocity past the motor app ear from the
following table.
It is recommended to instal l the motor a bove the wel l
screen in order to a chieve proper motor coolin g.
TM03 8129 0507
Caution
Before fitting the mo tor to a pump a fter
a long period of st orage, lubr icate the
shaft seal by adding a few drops of
water and turning the shaft.
45°
TM03 2065 3605
Motor type
Power output
50 Hz
Power output
60 Hz
[kW] [kW]
MS All sizes All s izes
MMS 6000 3.7 to 30 3.7 to 30
MMS 8000 22 to 92 22 to 9 2
MMS 10000 75 to 170 75 to 170
MMS 12000 147 to 220 –
Caution
During operation, the motor must
always be completely subme rged in the
liquid. Please consu lt the pump
manufacturer's NPSH data.
Warning
If the motor is use d in hot liq uids
(40 to 60 °C), it mu st be ensured that
persons cannot come into cont act with
the motor and the in stallation, e. g. by
installing a guard.
45°
A
98
Pt1000
MS4”
Pt100/1000
MS6”
Pt100/1000
MMS6”/8”
Pt100/1000
MMS10”
Pt100/1000
MMS12”
GRUNDFOS Holding A/S
Poul Due Jensens Vej 7
DK-8850 Bjerringbro
Tel: +45 87 50 14 00
www.grundfos.com
The name Grundfos, the Grundfos logo, and be think innovate
are registered trademarks owned by Grundfos Holding A/S
or Grundfos A/S, Denmark. All rights reserved worldwide.
98445663 0216
ECM: 1176159
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

Grundfos PT100 Instructions Manual

Grundfos
Brand
Grundfos
Model
PT100
Type
Instructions Manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents