VEGETABLE CUTTING MACHINE
OPERATION MANUAL
LR-MFC60/LR-MFC-65
LR-MFC-60P/LR-MFC-65P
LR-MFC60/LR-MFC60P
LR-MFC65/LR-MFC65P
1. GENERAL PROFILE
1.1. DESCRIPTION
THE MULTI-PURPOSE VEGETABLE CUTTER MACHINE CAN SLICE, SHRED, GRATE, CHIP AND
DICE VARIOUS FOODSTUFFS ( FOR THE PREPARATION OF RAW AND COOKED VEGETABLES,
FRUITS AND CHEESES ).
WITH ITS RANGE OF HIGH OUTPUT CUTTERS, THE MACHINE IS IDEAL FOR RESTAURANTS,
LARGE OPENING KITCHENS, INSTITUTION AND SMALL COMPANIES.
1.2. GENERAL PRECAUTIONS
·THE VEGETABLES CUTTING MACHINE MUST BE MANAGED BY SKILLED PERSONNEL,
FAMILIAR WITH THE INSTRUCTIONS FOR USE AND SAFETY CONTAINED IN THIS
MANUAL.
·IN THE CASE OF ROTATION OF THE PERSONNEL , VOCATIONAL TRAINING IS NECESSARY.
·EVEN IF THE MACHINE COMES WITH SEVERAL SAFETY SYSTEMS, AVOID SETTING THE
HANDS NEAR THE CUTTING DISCS AND MOVING PARTS.
·BEFORE ANY CLEANING AND MAINTENANCE OPERATIONS, CHECK TO MAKE SURE THE
MACHINE IS DISCONNECTED FROM THE MAINS.
·PERIODICALY CHECK CABLES AND ELECTRIC ELEMENTS CONDITIONS.
·DO NOT USE THE MACHINE TO CUT FROZEN FOODS. REMOVE ALL HARD PARTS FROM
FOODS BEFORE CUTTING TO AVOID DAMAGING THE CUTTING BLADES.
·NEVER REPLACE PARTS OF THE MACHINE BY YOURSELF, BUT APPLY TO THE ASSISTANCE
SERVICE.
2. TECHNICAL FEATURES
2.1. SPECIFICATION SHEET
MODEL DIMENSIONS
CM.
WEIGHT
KG.
POWER
WATTS
ELECTRICAL
CONNECTION
RPM
DISC
LR-MFC-60P 50X27X47 23 550W or 750W
FOR YOUR
CHOICE
230V/1/50Hz
115V/1/60Hz
380V/3/50Hz
300 RPM
LR-MFC60 50X25X46 24.5
LR-MFC-65P 50X27X48 24
LR-MFC-65 50X25X47 26
2.2. SUPPLY CONDITIONS AND DISPOSAL OF PACKINGS
THE CUTTING MACHINE IS PACKED IN A STURDY CARDBOARD BOX WITH INTERNAL
SHAPED EDGES WHICH GUARANTEE THE PERFECT INTEGRITY OF THE MACHINE DURING
TRANSPORT.
THE EQUIPMENT INCLUDE:
·INSTRUCTIONS FOR USE AND MAINTENANCE
·EJECTING DISC
ALL THE PACKING COMPONENTS (CARTON, FOAM, STRAPS, AND SO ON) CAN EASILY BE
DISPOSED OF AS HOUSEHOLD RUBBISH
3. INSTALLATION
3.1. SETTING THE MACHINE
THE MACHINE CONNECTION AND THE SETTING AT WORK MUST BE MADE BY SKILLED
PERSONNEL.
WARNING: BOTH THE SYSTEM AND LOCATION WHERE THE EQUIPMENT HAS TO BE SET
MUST COMPLY WITH THE REGULATIONS FOR THE ACCIDENT PREVENTION AND
ELECTRICAL REGULATIONS IN FORCE.
THE MANUFACTURER DECLINES ANY AND ALL RESPONSIBILITY FOR DIRECT OR
INDIRECT DAMAGES WHICH MAY ENSUE FOR NON-COMPLIANCE WITH THE ABOVE
MENTIONED REGULATIONS.
SET THE EQUIPMENT ON A WIDE, LEVELLED, DRY AND FIXED FACE, FAR FROM HEAT
SOURCES AND WATER SPRAYS.
3.2. ELECTRIC CONNECTIONS
THE EQUIPMENT IS SUPPLIED WITH AN ELECTRIC CABLE TO BE CONNECTED TO A
MAGNETO-THERMIC MAIN SWITCH WHICH STOPS THE MACHINE WHEN THE OPERATOR
COMES IN FORTUITOUS CONTACT WITH THE ROTATING ELEMENTS.
IT IS IMPERATIVE THAT THE EQUIPMENT IS WELL GROUNDED ACCORDING TO THE
REGULATIONS IN FORCE.
THE MANUFACTURER DECLINES ANY AND ALL RESPONSIBILITY FOR DIRECT AND
INDIRECT DAMAGES WHICH MAY ENSUE FOR NON-COMPLIANCE WITH THE
REGULATIONS IN FORCE.
THE CUTTING MACHINE IS MANUFACTURED INTO SINGLE-PHASE V.220/1/50 HZ OR
V.115/1/60HZ. WHENEVER THE VOLTAGE DIFFERS FROM THE ABOVE MENTIONED,
PLEASE APPLY TO THE MANUFACTURER, OR THE AUTHORIZED DISTRIBUTOR.
3.3. SAFETY MEASURES AND TRAINING THE FINAL USER
THE SKILLED PERSONNEL IN CHARGE OF THE INSTALLATION AND ELECTRIC
CONNECTIONS OF THE EQUIPMENT IS RESPONSIBLE OF THE TRAINING OF THE FINAL
USER, WHICH MUST ALSO BE INFORMED ON THE SAFETY MEASURES TO COMPLY WITH.
THIS INSTRUCTION MANUAL COMES WITH EACH EQUIPMENT.
4. USE OF THE EQUIPMENT
4.1. CONTROLS
THE CONTROLS AND PILOT LIGHT ARE LOCATED IN THE FACE OF MIDDLE ALUMILIUM
BASE.
1. GREEN BUTTON FOR STARTING THE MACHINE
2. RED BUTTON FOR STOPPING THE MACHINE
4.2. SETTING THE DISCS ON THE MACHINE
LIFT UP THE LOCKING HANDLE AS SHOWN IN FIGURE NO. 1 AND OPEN THE COVER. PUT
AWAY THE PLASTIC EJECTING DISC, THEN CHOOSE A DISC OR A DISCS CHOICE
ACCORDING TO YOUR PURPOSE. CLOSE THE COVER. WORK ON THE START BUTTON TO
AUTOMATICALLY HOOK THE DISCS IN THE CORRECT POSITION.
C
OVER OPENING (1) DISC POSITION (2)
ATTENTION TO DISC BLADES!!
4.3. CHOICE OF THE DISCS
DISC CHOICE FOR VEGETABLE CUTTER MACHINE
PICTURE PART NO. SIZE
Shredding
G002 2mm
G003 3mm
G005 5mm
G007 7mm
G010 10mm
Slicer (aluminium)
SA002 2mm (three blades)
SA004 4mm (two blades)
SA006 6mm (two blades)
SA008 8mm (single blade)
SA010 10mm (single blade)
Slicer (plastic)
SP002 2mm (three blades)
SP004 4mm (three blades)
Julienne
J303 3x3mm
J404 4x4mm
French Fries
FS808 8x8mm
FS100 10x10mm
Dicing
DS888 8x8x8mm
DS1000 10x10x10mm
DS2000 20x20x20mm
4.4. USE OF THE DISCS
THE UNIT IS SUPPLIED WITH THE EJECTOR FITTED TO THE DRIVE SPINDLE. OPEN THE
COVER LOCK AND LIFT THE COVER FULLY IN ORDER TO REMOVE THE EJECTOR.
BEFORE STARTING WORK, ALWAYS CHECK THE CLEANLINESS OF THE CUTTING CHAMBER,
THE DRIVE SPINDLE, THE EJECTOR, THE CUTTING DISCS AND THE GRID.
1) FOR SLICING, SHREDDING AND GRATING
·FIT THE EJECTOR ONTO THE FLAT OF THE DRIVE SPINDLE.
·FIT THE DISC REQUIRED (SLICING, SHREDDING OR GRATING).
-- TURN THE DICS IN A CLOCKWISE DIRECTION TO INSERT THE BAYONET FITTING, THEN
CONTINUE IN THE SAME DIRECTION UNTIL IT REACHES THE PIN.
-- TO REMOVE THE DISC, TURN IT IN THE OPPOSITE DIRECTION AND LIFT IT USING THE
FINGER HOLES AT THE EDGES OF THE DISC.
-- CLOSE THE COVER AND LOCK IT.
2) FOR CUTTING INTO CHIPS OR CUBES
·FIT THE EJECTOR.
·FIT THE GRID INTO ITS HOUSING AND CHECK THAT IT IS SEATED CORRECTLY (SEATING
AREA IS CLEAN). THE UPPER FACE OF THE GRID MUST BE SLIGHTLY BELOW THE TOP OF
THE MACHINE BODY.
·THEN FIT THE CHOSEN DISC AND CLOSE THE LID.
5. CLEANING AND MAINTENANCE OPERATIONS
5.1. GENERALITIES AND PRODUCTS FOR CLEANING
BEFORE CARRYING OUT ANY CLEANING OR MAINTENANCE OPERATIONS, CHECK TO
MAKE SURE THAT THE MAINS SWITCH BE OFF AND THE SUPPLY PLUG DISCONNECTED
FROM THE MAINS.
ACCURATELY CLEAN THE EQUIPMENT AND THE DISCS EVERY DAY FOR A CORRECT
OPERATION AND LIFE OF THE EQUIPMENT.
THE DISCS, THE GRID FOR CUTTING DICES, AND THE PLASTIC EJECTOR, CAN BE REMOVED
FOR WASHING UNDER A WARM WATER JET.
CLEAN THE MACHINE, AND ABOVE ALL WHERE THE DISCS REST, WITH A CLOTH OR A
SPONGE WET WITH WARM WATER, ACCURATELY REMOVE ALL WASTES TO PREVENT THE
DISCS FROM CHANGING THEIR POSITION.
OPEN THE COVER AND LOOSEN THE 1 PIN AS SHOWN IN FIG.3. REMOVE THE COVER AND
WASH UNDER A WATER JET.
(3)
CLEAN THE SURFACES WITH WATER AND SOUP, ALCOHOL, DETERGENTS WITHOUT
ABRASIVES OR SUBSTANCES BASED ON CHLORINE OR SODA (CHLORINE WATER,
MURIATIC ACID).
NEVER USE ABRASIVES, STEEL WOOL, OR SIMILAR PRODUCTS AS THEY MAY BRING
DAMAGES TO THE PAINT, THE COAT, OT THE MACHINE BODY.
FOR CLEANING, USE NON-TOXIC PRODUCTS AND ONES THAT GUARANTEE THE BEST
HYGIENE.
5.2. OPERATIONS IN THE CASE OF FAILURES
WHEN THE WHITE POLIT LIGHT ON THE PANEL IN ON, BUT THE MACHINE DOES NOT START,
CHECK TO MAKE SURE THAT THE HANDLE AND THE COVER ARE CLOSED. IN THIS WAY,
BOTH THE SAFETY MICROSWITCHES. THE SAFETY MICROSWITCHES PREVENT THE
MACHINE START WHENEVER ALL SECURITIES ARE NOT ACTIVATED.
IN THE CASE OF FAILURES, DISCONNECT THE MAIN WALL SWITCH AND EITHER WARN THE
MAINTENANCE SERVICE, OR THE SKILLED PERSONNEL.
NEITHER START NOR TAMPER WITH THE EQUIPMENT PERSONALLY.
5.3. MACHINE IDLE FOR A LONG TIME
SHOULD THE MACHINE BE IDLE FOR A LONG TIME, DISCONNECT THE MAIN WALL SWITCH
AND CLEAN
THE MACHINE AND ITS ACCESSORIES ACCURATELY. USE WHITE VASELINE OIL (OR
SIMILAR PRODUCTS)
TO PROTECT ALL THE MACHINE'S ELEMENTS.
THESE PRODUCTS, MAINLY MADE UP OF OILY AND DETERGENT SUBSTANCES, AND NOW
AVAILABLE IN SPRAY CYLINDERS FOR EASY APPLICANT, BESIDES GIVING A GLOSSY
ASPECT TO THE ALUMINIUM MAGNESTISM ALLOY, PREVENT MOISTURE AND DIRT FROM
GETTING INSIDE THE MACHINE, HENCE, ITS CORROSION.
WE ADVISE COVERING THE MACHINE WITH A NYLON (OR SIMILAR) CLOTH.
ILLUSTRATIONS
58
68
23
22
67
19
65
64
62
63
61
60
59
56
55
54
49
29
28
9
11
8
7
6
5
4
3
2
1
10
12
13
15 16 17 18 19 20 21
25
26
27
30
31
32
35
36
37
38
34
39
40
41 42
43
45
46
47
48
50
51
52
44
33
53
69
33
7
19
57
66
19
28
70
71
24
14
No. Part Name No. Part Name No. Part Name No. Part Name
1 screw 19 screw 37 motor 55 nut
2 handlebar 20 hopper lid spindle 38 ejector 56 bearing
3 gasket 21 gasket 39 core of disc 57 bolt
4 22 power cord 40 output axis 58 strapped wheel
5 23 body 41 on-off switch 59 belt
6 24 screw 42 woodruff key 60 belt wheel
7 25 magnet steel 43 bearing cover 61 nut
8 26 seat of magnet( new) 44 oil seal 62 screw
9 27 pin 45 bearing 63 support of electric box
10 hopper 28 nut 46 pin sleeve 64 electric box
11 seat of magnet 29 47 fixing flat 65
12 magnet steel 30 48 microswitch 66 clamp
13 screw 31 49 screw 67 capacitor
14 disc 32 50 support of motor 68
15 spring 33 51 bolt 69 foot
16 hook 34 52 front cover of motor 70 support of contactor
17 pin 35 53 gasket 71 contactor
18 locking handle 36 54 screw
pusher
LR-MFC60 Spare Parts List
motor
small feeeder hopper
66
78
26
25
77
22
75
74
72
73
68
67
64
63
62
30
9
14
8
7
5
4
321
10
15
16 17 18 19
23 24
27
28
31
32
33
36
37
38
39
35
41
42
43 57
58
60
45
47
48
53
56
59
34
51
79
34
21
5
54
65 76
54
40
71
70
20 21 22
11
29
46
52
55
69
44
61
11
12
13
6
50
49
No. Part Name No. Part Name No. Part Name No. Part Name
1 handlebar arm 21 spring washer 41 nut 61 shalf sleeve
2 Screw 22 screw 42 output axis 62 screw
3 handlebar arm 23 hopper lid spindle 43 On switch 63 nut
4 gasket 24 gasket 44 Off switch 64 bearing
5 gasket 25 power cord 45 pin sleeve 65 bolt
6 gasket bolt 26 body 46 flat washer 66 strapped wheel
7 pusher cap 27 seat of magnet 47 fixing flat 67 belt
8 pusher 28 pin 48 screw 68 belt wheel
9 small feeder hopper 29 screw 49 microswitch-A 69 nut
10 hopper 30 stator 50 microswitch-B 70 contactor
11 seat of magnet 31 rotor 51 flat washer 71 support of contactor
12 magnet steel 32 motor sha 52 screw 72 screw
13 screw 33 spring gasket 53 support of motor 73 support of electric box
14 G003 grater disc 34 bearing 54 screw 74 electric box
15 disc 35 ripple gasket 55 bolt 75 boom base
16 spring 36 motor back cover 56 front cover of motor 76 clamp
17 hook 37 fan 57 square Key 77 capacitor
18 pin 38 spring gasket 58 bearing cover 78 boom plate
19 locking handle 39 ejector 59 oil seal 79 foot
20 flat washer 40 core of disc 60 bearing cover
LR-MFC-65 Spare Parts List
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Hendi 231852 User manual
-
Hendi 231852 User manual
-
VBENLEM 110V Continuous Feed Vegetable Cutter 2 Feeding Holes, Commercial Food Processor 550W 1600 RPM Stainless Steel Construction, Detachable 6-blades Included, 3mm/4mm/7mm Shred, 2mm/4mm Slice User guide
-
Omcan HLC300 User manual
-
Electrolux TR22S2D (601701) Operating instructions
-
Robot Coupe CL 60 E Operating Instructions Manual
-
Avantco CFP5D User manual
-
Sirman GP CE User manual
-
-
Robot Coupe CL 52 Owner's manual
