1. Package contents 2. Interface and LED Indicator 5. Configuration Steps
1)On the start page of the setup wizard, click Next.
Username
Address
Telephone No.
Purchase Shop
Purchase Address
Product Model No.
Purchase Time
Serial No.
Dealer Signature
If the product defects within three months after purchase, we will provide you a new
product of the same model.
If the product defects within the three-year warranty period, we will provide the
professional maintenance service.
Proof of purchase and a complete product serial number are required to receive any
services guaranteed as part of the limited warranty.
Any other defects that are not caused by workmanship or product quality, such as
natural disaster, water damage, extreme thermal or environmental conditions. sticker
damaged, warranty card losing will disqualify the product from limited warranty.
Warranty Card
www.wireless-tek.com
WI-R3
1200Mbps Dual-Band Wireless Mesh Router with PoE Passthrough
www.wireless-tek.com
WI- R3
1200 Mbps Du al-Ba nd Wire less Me sh Rout er with P oE Pass throu gh
Quick I ns tall Guid e
SYS PWR 2.4G 5G 2.4G LINK 5G LINK LAN1 LAN2 LAN3 WAN MESH
SYS PWR 2.4G 5G 2.4G L INK 5G LIN K LAN1 LAN2 LAN3 WAN MESH
WAN
PoE OU T
LAN3
PoE OU T
LAN2
PoE OU T
LAN1
PoE IN
POE
OFF ON RESE T
DCIN 1 2-54V
WAN/LAN3/LAN2 PoE OUT
LAN1 with PoE IN PoE OUT Slide Switch
RESET
DC IN 12V-54V
LED Description
PWR On: the device is powered up.
Off: the device is powered off.
SYS On: the device is running normally.
Off: the device is running abnormal.
2.4G On:2.4G Wi-Fi is normally.
Off:2.4G Wi-Fi is abnormal.
5G On:5G Wi-Fi is normally.
Off:5G Wi-Fi is abnormal.
2.4G LINK On:2.4G has link connection.
Off:2.4G has no link connection.
5G LINK On:5G has link connection.
Off:5G has no link connection.
LAN1/LAN2/LAN3 Flicker: LAN1/LAN2/LAN3 interfaces have forwarding data access.
Off: LAN1/LAN2/LAN3 interfaces do not forward data access.
WAN Flicker: WAN interfaces have forwarding data access.
Off: WAN interfaces do not forward data access.
MESH On: Mesh networking is successful.
Off: There is no device in Mesh networking.
3. Network Application
PoE Power
Power and data transfer functions are performed over a single cable, eliminating the need to
deploy power outlets for devices such as cameras.
Wireless mesh networking
Provide whole-home Wi-Fi coverage and eliminate weak signals once for all.
WAN
PoE OUT
LAN3
PoE OUT
LAN2
PoE OUT
LAN1
PoE IN
POE
OFF ON RESET
DCIN 12-54V
LAN+POE O ut LAN+POE O ut
24V OR 48V
PoE Injec to r
DC12V-54 V
OR
Wireless CPE
WAN+PoE Out
Internet
WISP
4. Login Method
Internet
Setup new Master AP
Please connect devices according to the above topology.
Follow the steps for quick Router configuration, using the initial setup wizard:
Step 1 Connect your PC to the device via Ethernet or Wireless.
Note: Default WiFi name: Wi-Tek-XXXX, Password: 88888888
Step 2 To log in to the router, launch a web browser and enter http://192.168.10.1 in the address.
The login page will appear. By default, both the username and password are admin.
2)When the device is connected to the Internet, you can set three options: PPPoE, DHCP
Client, and Static IP, and then click Next.
3)For the WiFi page, you can select the country code and configure SSID, encryption, key.
Also, choose whether to enable guest WiFi. Click NEXT.
4)Click the COMPLETE button to complete the setting.
5)The following page will appear after the configuration is complete. Make sure your device
is connected to the internet.
6. Cloud Management Settings
Step 1 Launch your web browser then enter http://cloud2.wireless-tek.com in the address bar.
Step 2 Register an account password by user name or email.
Step 3 log in to the cloud account with the account password after registration.
After the login is successful, the steps to bind the device to the cloud
account are as follows:
1)Click ADD NETWORK
2) Fill in the group name and location, and click save.
3)And click next.
4)Enter the serial number, click ADD to create and click FINISH, the configuration is complete.
Note: The 17-digit SN code of the Add device is shown on the sticker on the back of the device.
5) In the relevant device options, you can see the bound device information.
6)Click Tunnel, Select binding device type, click EWEB to log in to the device.
Wireless-Tek Technology Limited
Address: Biaofang Technology Building 402, Bao'an street,
Baoan District,Shenzhen City, Guangdong, China
Website:www.wireless-tek.com
Tel:86-0755-32811290
Email:sales@wireless-tek.com
Technical Support:tech@wireless-tek.com
Company Website
Cloud Management
Technical Support
RoHS
Quick Install Guide
/
