V I V O STAND-V001VA User manual

Brand: V I V O

Model: STAND-V001VA

Category: Flat panel desk mounts

Type: User manual

Single Monitor Desk Mount with

VESA Adapter Bracket

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-v001va

SKU: STAND-V001VA

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a

qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may

cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do

not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly

or inappropriate use.

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

PACKAGE CONTENTS

A (x1)

Pole

B (x1)

Clamp

C (x1)

Swivel Arm

T-A (x1)

3mm Allen

Wrench

T-B (x1)

5mm Allen

Wrench

J (x1)

Pole Cable

Clip

G (x1)

So Pad

H (x1)

Support Plate

I (x2)

Arm Cable

Clip

D (x1)

VESA Plate

E (x1)

Pole Cap

S-A (x3)

M6x16mm Screw

S-F (x8)

Nut

S-G (x8)

Carriage Bolt

M-A (x4)

M4x12mm

Thumbscrews

M-B (x4)

M4x30mm

Screws

M-C (x4)

Spacers

S-B (x4)

M6x40mm Screw

S-C (x4)

M6x60mm Screw

S-D (x4)

M6x80mm Screw

S-E (x1)

M6 Cap Nut

F (x1)

Grommet Plate

T-C (x1)

6mm Allen

Wrench

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

K (x4)

Bracket Arm

L (x4)

“L” Support

Holder

M (x4)

Plastic Cover

T-D (x1)

Wrench

Alternative mounting hardware (if Bracket Arms are not used)

Desk Clamp Installation

Mount Clamp (B) to Pole (A) using M6x16mm Screws (S-A) 3mm Allen Wrench (T-A). Secure assembly

to desktop by tightening knob on Clamp (B).

ASSEMBLY STEPS

STEP 1

STEP 2 (Option A)

TOOLS NEEDED 17.6lbs

(8kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

Phillips

Screwdriver

Loosen knob on Clamp (B).

T-A

S-A

Mount Grommet Plate (F) to Pole (A) using M6x16mm Screws (S-A) and 3mm Allen Wrench (T-A).

Remove adhesive backing from So Pad (G) and adhere to Grommet Plate (F).

If desk does not have an existing grommet hole, drill a 3/8” (10mm) diameter hole at the desired

position through the mounting surface.

Position Pole (A) on the mounting surface and secure

using Knob (B2) and Support Plate (H).

STEP 2 (Option B)

Grommet Installation

Using a phillips screwdriver, remove the screw from Clamp (B) and disassemble. Set Knob (B2) aside.

S-A

T-A

Slide Pole Cable Clip (J) and Swivel Arm (C) onto Pole (A). Tighten Swivel Arm (C) at desired height

using 6mm Allen Wrench (T-C). Insert Pole Cap (E) into top of Pole (A). Attach arm Cable Clips (I) onto

Swivel Arm (C).

Attach “L” Support Holders (L) to Bracket Arms (K)

using appropriate M6 Screws (S-B, S-C, or S-D)

for monitor thickness and a Phillips screwdriver.

Do not tighten fully.

Connect VESA Plate (D) to assembled arms using Carriage Bolts (S-G), Nuts (S-F),

Wrench (T-D) and a Phillips screwdriver. Arms can be assembled in one of four

methods, which are shown below and on next page.

STEP 3

STEP 4

STEP 5

T-C

S-B/C/D

T-D

S-F

S-G

STEP 5 (Continued)

T-D

S-F

S-G

T-D

S-F

S-G

T-D

S-F

S-G

STEP 6

With all “L” Support Holders (L) facing up, place monitor on lower two holders and fully tighten lower

two screws with a Phillips screwdriver. Turn top holders down and tighten top screws, then tighten

nuts for the upper arms. Install Plastic Covers (M) into “L” Support Holders (L).

STEP 7

STEP 8

Slide monitor assembly onto Swivel Arm (C) and secure with M6 Security Screw (S-E).

Route cables through Arm Cable Clips (I) and Pole Cable Clip (J). Use 5mm Allen Wrench (T-B) to

adjust tilt and swivel on VESA plate head.

S-E

T-B

CAUTION:

To avoid risk of monitors sliding o,

DO NOT rotate monitors beyond +5° or -5°.

LAST UPDATED: 01/16/2023

REV1.2

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303

V I V O STAND-V001VA User manual

Brand: V I V O

Model: STAND-V001VA

Category: Flat panel desk mounts

Type: User manual

Download PDF

report

V I V O STAND-V001VA User manual

V I V O STAND-V001VA User manual

Related papers

Other documents