Chief FMSCA Installation guide

Brand: Chief

Model: FMSCA

Category: Projector accessories

Type: Installation guide

This manual is also suitable for

FMSCM

INSTALLATION INSTRUCTIONS

FMSCM

FMSCA

Fusion Modular Ceiling Heads

Spanish Product Description

German Product Description

Portuguese Product Description

Italian Product Description

Dutch Product Description

French Product Description

FMSCM / FMSCA

FMSCM / FMSCA Installation Instructions

DISCLAIMER

Milestone AV Technologies and its affiliated corporations and

subsidiaries (collectively “Milestone”), intend to make this

manual accurate and complete. However, Milestone makes no

claim that the information contained herein covers all details,

conditions or variations, nor does it provide for every possible

contingency in connection with the installation or use of this

product. The information contained in this document is subject

to change without notice or obligation of any kind. Milestone

makes no representation of warranty, expressed or implied,

regarding the information contained herein. Milestone assumes

no responsibility for accuracy, completeness or sufficiency of

the information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies.

DEFINITIONS

MOUNTING SYSTEM: A MOUNTING SYSTEM is the

primary Chief product to which an accessory and/or component

is attached.

ACCESSORY: AN ACCESSORY is the secondary Chief

product which is attached to a primary Chief product, and may

have a component attached or setting on it.

COMPONENT: A COMPONENT is an audiovisual item

designed to be attached or resting on an accessory or mounting

system such as a video camera, CPU, screen, display,

projector, etc.

WARNING: A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the

corresponding instructions.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,

damage to equipment, or voiding of factory warranty! It is the

installer’s responsibility to make sure all mounting systems /

accessories are properly assembled and installed using the

instructions provided.

WARNING: Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the

installer’s responsibility to make sure the combined weight of

all components attached to mounting system does not

exceed the weight capacity listed in the Fusion Modular

Systems installation instructions.

IMPORTANT ! : These installation instructions must be

used in conjunction with the Fusion Modular Systems

installation instructions.

--SAVE THESE INSTRUCTIONS--

Installation Instructions FMSCM / FMSCA

DIMENSIONS

7.69

195.3

8.21

208.6

0.59

15.1

3.25

82.6

3.25

82.6

1.53

38.9

C/L OF

COLUMN 4.25

108.0

4.50

114.3

7.00

177.8

2.72

69.1

2.00

50.8

TOTAL HEIGHT

ADJUST

3.84

97.6

6.96

176.7

1.53

38.9

HEIGHT ADJUST

SCREW

5.38

136.5

1.00

25.4

5.00

127.0

1.53

38.9

2.50

63.5

2.50

63.5

1.34

34.1

2.84

72.3

0.55

14.1

EXTRUSION SOLD

SEPARATELY

DIMENSIONS: INCHES

[MILLIMETERS]

FMSCM

7.85

199.5

7.69

195.3

3.25

82.6

3.25

82.6

0.59

15.1

4.50

114.3

7.00

177.8

2.72

69.1

1.53

38.9

C/L OF

COLUMN

4.25

108.0

3.84

97.6

2.00

50.8

TOTAL HEIGHT

ADJUST

6.96

176.7

1.53

38.9

FLOATING HEIGHT ADJUST

ADJUSTMENT SCREW

5.38

136.5

1.00

25.4 2.84

72.3

1.34

34.1

5.00

127.0 2.50

63.5

2.50

63.5

0.55

14.1

EXTRUSION SOLD

SEPARATELY

FMSCA

DIMENSIONS: INCHES

[MILLIMETERS]

FMSCM / FMSCA Installation Instructions

LEGEND

Tighten Fastener

Apretar elemento de fijación

Befestigungsteil festziehen

Apertar fixador

Serrare il fissaggio

Bevestiging vastdraaien

Serrez les fixations

Loosen Fastener

Aflojar elemento de fijación

Befestigungsteil lösen

Desapertar fixador

Allentare il fissaggio

Bevestiging losdraaien

Desserrez les fixations

Phillips Screwdriver

Destornillador Phillips

Kreuzschlitzschraubendreher

Chave de fendas Phillips

Cacciavite a stella

Kruiskopschroevendraaier

Tournevis à pointe cruciforme

Open-Ended Wrench

Llave de boca

Gabelschlüssel

Chave de bocas

Chiave a punte aperte

Steeksleutel

Clé à fourche

By Hand

A mano

Von Hand

Com a mão

A mano

Met de hand

À la main

Hex-Head Wrench

Llave de cabeza hexagonal

Sechskantschlüssel

Chave de cabeça sextavada

Chiave esagonale

Zeskantsleutel

Clé à tête hexagonale

Pencil Mark

Marcar con lápiz

Stiftmarkierung

Marcar com lápis

Segno a matita

Potloodmerkteken

Marquage au crayon

Drill Hole

Perforar

Bohrloch

Fazer furo

Praticare un foro

Gat boren

Percez un trou

Adjust

Ajustar

Einstellen

Ajustar

Regolare

Afstellen

Ajuster

Remove

Quitar

Entfernen

Remover

Rimuovere

Verwijderen

Retirez

Optional

Opcional

Optional

Opcional

Opzionale

Optie

En option

Security Wrench

Llave de seguridad

Sicherheitsschlüssel

Chave de segurança

Chiave di sicurezza

Veiligheidssleutel

Clé de sécurité

Installation Instructions FMSCM / FMSCA

TOOLS REQUIRED FOR INSTALLATION

PARTS

1/2" (12.7mm)

5/32" - included

3/32" - included

3/16" - included

1/2" (12.7mm)

A (2)

5/16-18 x 2"

B (2)

[Friction washer] C (2)

5/16" D (4)

5/16-18 x 1/2"

E (2)

5/16-18 x 3/4" F (1)

5/32" G (1)

3/32" H (1)

3/16"

J (1)

10-24 x 1/4"

Menu Board Ceiling Head Hardware Kit

K (1)

[Ceiling head -

height-adjust] L (1)

[Ceiling head -

floating]

M (1)

(FMSCM only)

[Bottom coupling]

(FMSCA only)

N (1)

[Hook plate] P (1)

[Back cover]

FMSCM / FMSCA Installation Instructions

INSTALLATION

NOTE: The following procedure assumes that Chief UL Listed

CPA or CMA ceiling plates (not included) and

extension columns (not included) have been properly

installed following instructions provided with ceiling

plates and extension columns.

•The ceiling plates and columns should be installed

approximately spaced at center of outside

screens, and spacings should not exceed those

outlined in the Fusion Modular Systems

installation instructions.

IMPORTANT ! : The weight of the system should be

evenly distributed across ceiling plates.

IMPORTANT ! : Also be sure to reference ceiling system

attachment guidelines in the Fusion Modular Systems

installation instructions.

NOTE: Proceed to Attaching Ceiling Head to NPT Column

section or Attaching Ceiling Head to CPA Column

section, as appropriate.

Attaching Ceiling Head to 1-1/2" NPT Column

1. Slide ceiling head (K or L) up from below onto installed

column (not included). (See Figure 1)

2. Thread bottom coupling (M) onto installed column until tight,

with a minimum of four threads engaged. (See Figure 1)

3. Install and tighten one 10-24 x 1/4" set screw (J) into bottom

coupling (M). (See Figure 1)

Figure 1

4. Tighten two 5/16" x 3/4" set screws (E) against column.

(See Figure 2)

Figure 2

Attaching Ceiling Head to CPA Column

1. Slide ceiling head (K or L) up from below onto installed

column (not included). (See Figure 3)

2. Line up holes in sides of ceiling head (K or L) with holes in

column.

Figure 3

3. Install two 5/16" x 2" self-tapping screws (A) through two 5/16"

lock washers (C), two friction washers (B), sides of ceiling

head (K or L), and into installed column. (See Figure 3)

(J)

(K or L)

(M)

(K or L)

(E) x 2

(K or L)

(A) x 2

(B) x 2

Installation Instructions FMSCM / FMSCA

4. Install and tighten two 5/16" set screws (E) against column.

(See Figure 4)

Figure 4

Attaching Mounting Rail to Ceiling Head

IMPORTANT ! : Use the FMSCM height-adjust ceiling head

(K) on the outside of the mounting rails, or FMSCA floating

ceiling head (L) at the center of the mounting rails.

NOTE: Attach one end cap to one end of mounting rail

following instructions included with the FMSECAP.

1. Slide the hook plate (N) into mounting rail. (See Figure 5)

Figure 5

2. Lift the mounting rail with the hook plate up to the ceiling

head (K or L). (See Figure 6)

3. Attach hook plate (N) with mounting rail to ceiling head (K

or L) using four 5/16 x 1/2" button head cap screws (D).

(See Figure 6)

Figure 6

Adjust and Level Mounting Rail via Ceiling Head

1. Adjust the height of the ceiling head, as necessary, to level

the mounting rail across the columns. (See Figure 7)

•Tighten the ceiling head height-adjust screw on the

FMSCM to raise the mounting rail.

•Loosen the ceiling head height-adjust screw on the

FMSCM to lower the mounting rail.

2. Tighten the adjustment screw at the bottom of the FMSCA

ceiling head to hold the FMSCA (center) ceiling head at the

same level as the FMSCM (outer) ceiling heads.

Figure 7

3. Add back cover (P) to ceiling head (K or L). (See Figure 7)

4. Attach remaining end cap to end of mounting rail following

instructions included with the FMSECAP.

(E) x 2

(K or L)

(N)

Front of

mounting

rail

(N)

(D) x 4

(Column

not shown)

Height-adjust

screw

FMSCM

FMSCA

ceiling head

(side view)

Adjustment

screw

(P)

Installation Instructions

USA/International A 6436 City West Parkway, Eden Prairie, MN 55344

P800.582.6480 / 952.225.6000

F877.894.6918 / 952.894.6918

Europe A Franklinstraat 14, 6003 DK Weert, Netherlands

P+31 (0) 495 580 852

F+31 (0) 495 580 845

Asia Pacific A Office No. 918 on 9/F, Shatin Galleria

18-24 Shan Mei Street

Fotan, Shatin, Hong Kong

P852 2145 4099

F852 2145 4477

Chief, a products division of

Milestone AV Technologies

8800-002849 Rev00

2016 Milestone AV Technologies

www.milestone.com

06/16

Chief FMSCA Installation guide

Brand: Chief

Model: FMSCA

Category: Projector accessories

Type: Installation guide

This manual is also suitable for

FMSCM

Download PDF

report

in other languages

français: Chief FMSCA Guide d'installation

Chief FMSCA Installation guide

This manual is also suitable for

Chief FMSCA Installation guide

in other languages

Related papers