2. Rev-A-Shelf
  3. 447-BCSC-6C

Rev-A-Shelf 447-BCSC-6C, 447-BCSC-9C Instruction Sheet

  • Hello! I've reviewed the user manual for the Rev-A-Shelf soft-close pullout systems, specifically the 9.5" and 6.5" models with Blum Tandem Slides. This manual provides instructions for installation, including attaching the slides to a cabinet, and mounting the cabinet door. I'm ready to assist with any questions you might have about these products.
  • What size drill bit is needed for pre-drilling holes?
    What size wrench should I use to loosen lock nuts?
    What type of screws are used to attach the door to the pullout unit?
    What type of screws are used to attach the slide assembly to the cabinet floor?
Center Line of Cabinet Opening
(4) Screw and Pilot
Hole Locations
Fold Template along
dotted line to t
cabinet opening
Front edge of paper
to front of cabinet
(or front of face frame)
12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
9.5” SOFT-CLOSE PULLOUT WITH BLUM TANDEM SLIDES WITH BLUMOTION
TOOLS REQUIRED:
30 MIN
ESTIMATED ASSEMBLY TIME:
CARE AND MAINTENANCE:
Clean with a damp cloth and
wipe parts dry.
PARTS LIST
- Frame assembly
- Slide assembly
- (4) #6 x 1/2” at head screw
- (4) #8 x 3/4” deep thread pan
head screw
- Template
- Rub Bushing Kit
3
32
Attaching slide to cabinet
1) Using the screw and pilot hole locations, pre-drill (4) holes using a 3/32” drill bit.
2)Removetemplateandattachtheslideassemblytotheoorofthecabinetusing(4)#8x3/4”deepthread
screws provided.
3)Withtheslidesinthefullyclosedposition,placetheframeontheslidesandpushbackuntilyoufeelthe
slidesengagethelockingdevices(youwillhearaclicksound).Fullycycletheframeafewtimes.
Attaching the cabinet door
1) Usinga3/8”wrench,loosenthe(4)locknutsinsidethefrontwalloftheunit(SeeFig1).
2) PulltheattachedAdjustableDoorMountingBracketstoensurethatyouaremountingtothe“thick”portion
ofthecabinetdoor(frontofpulloutshouldlineupwithfrontoffaceframe).
3) Usethe(4)#6x1/2”atheadscrewsprovidedtoattachthedoortothepulloutunit.
4) Ifthedoorneedstobeadjustedtolayushagainstthefaceframe,loosenthelocknutsandturnthe“T-Nut”
screwssotheT-Nutscrewspushagainstthemetalbracket.Eachcornercanbeadjustedindependently.
(Note:Itisrecommendedthatdoorbumpersbeusedoneachcornertoensurequietoperation)
Install rub bushings using enclosed kit and instructions (Note: Chassis may need to be removed for proper installation)
Fig1
T-NutScrewfor
TiltAdjustment
LockNut
T-448SCFL-0120
3
8
Center Line of Cabinet Opening
Front edge of paper
to front of cabinet
(or front of face frame)
Attaching slide to cabinet
1) Using the screw and pilot hole locations, pre-drill (4) holes using a 3/32” drill bit.
2)Removetemplateandattachtheslideassemblytotheoorofthecabinetusing(4)#8
x3/4”deepthreadscrewsprovided.
3)Withtheslidesinthefullyclosedposition,placetheframeontheslidesandpushback
untilyoufeeltheslidesengagethelockingdevices(youwillhearaclicksound).Fully
cycletheframeafewtimes.
Attaching the cabinet door
1) Usinga3/8”wrench,loosenthe(4)locknutsinsidethefrontwalloftheunit(SeeFig1).
2) PulltheattachedAdjustableDoorMountingBracketstoensurethatyouaremounting
tothe“thick”portionofthecabinetdoor(frontofpulloutshouldlineupwithfrontof
faceframe).
3) Usethe(4)#6x1/2”atheadscrewsprovidedtoattachthedoortothepulloutunit.
4) Ifthedoorneedstobeadjustedtolayushagainstthefaceframe,loosenthelock
nutsandturnthe“T-Nut”screwssotheT-Nutscrewspushagainstthemetalbracket.
Eachcornercanbeadjustedindependently.(Note:Itisrecommendedthatdoor
bumpersbeusedoneachcornertoensurequietoperation)
Install rub bushings using enclosed kit and instructions (Note: Chassis may need to be removed for
proper installation)
12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
6.5” SOFT-CLOSE PULLOUT WITH BLUM TANDEM SLIDES WITH BLUMOTION
TOOLS REQUIRED:
30 MIN
ESTIMATED ASSEMBLY TIME:
CARE AND MAINTENANCE:
Clean with a damp cloth and
wipe parts dry.
PARTS LIST
- Frame assembly
- Slide assembly
- (4) #6 x 1/2” at head screw
- (4) #8 x 3/4” deep thread pan
head screw
- Template
- Rub Bushing Kit
3
32
Fold Template along dotted line to t
cabinet opening.
Fig1
T-NutScrewfor
TiltAdjustment
LockNut
T-448SCFL-0120
3
8
(4) Screw and Pilot
Hole Locations
/