Quick Start Guide
Commercial tumble dryer
PDR910G
Gas-heated
To avoid the risk of accidents or damage to the
machine, it is essential to read these instruc-
tions before it is installed and used for the first
time.
en-GB
M.-Nr. 12 431 150
Contents
2
Warning and Safety instructions ................................................................................... 4
Extended documentation .................................................................................................. 4
Take these safety precautions if you smell gas................................................................. 5
Installation site................................................................................................................... 5
Appropriate use ................................................................................................................. 6
Foreseeable misuse........................................................................................................... 6
Technical safety................................................................................................................. 7
Correct use........................................................................................................................ 10
Accessories ....................................................................................................................... 11
Description of the machine ............................................................................................ 12
Operating the tumble dryer ............................................................................................ 13
Control panel..................................................................................................................... 13
Sensor controls and touch display with sensor controls .................................................. 14
Main menu......................................................................................................................... 14
“Programmes” menu ............................................................................................... 14
“Favourites” menu.................................................................................................... 14
“Supervisor” menu.................................................................................................. 14
Operating examples .......................................................................................................... 14
Selection lists ................................................................................................................ 14
Setting numerical values ............................................................................................... 15
Pull-down menu ............................................................................................................ 16
Exiting the menu ........................................................................................................... 16
Help display .................................................................................................................. 17
Drying ............................................................................................................................... 18
1. Notes on correct laundry care....................................................................................... 18
Washing before drying .................................................................................................. 18
Removing foreign objects ............................................................................................. 18
Care symbols ................................................................................................................ 18
2.Loading the tumble dryer .............................................................................................. 19
3. Selecting a programme ................................................................................................. 19
Switching on the tumble dryer ...................................................................................... 19
4. Selecting programme settings ...................................................................................... 20
Select the drying level................................................................................................... 20
Selecting extra options ................................................................................................. 20
5.Starting a programme ................................................................................................... 22
Payment device (optional)............................................................................................. 22
Calling up current programme parameters .................................................................. 22
Programme running time/Time left estimation.............................................................. 22
End of the programme ...................................................................................................... 23
End of programme ........................................................................................................ 23
Removing the laundry ................................................................................................... 23
Care notes..................................................................................................................... 23
Timer ................................................................................................................................. 24
Prerequisite for setting the timer ................................................................................... 24
Setting the timer............................................................................................................ 24
Problem solving guide .................................................................................................... 25
Fault diagnosis .................................................................................................................. 25
Contents
3
Installation........................................................................................................................ 27
Installation locations.......................................................................................................... 27
Front view...................................................................................................................... 27
Side view....................................................................................................................... 27
Rear view ...................................................................................................................... 27
View from above ........................................................................................................... 28
Installation on a plinth ................................................................................................... 28
Installation ......................................................................................................................... 29
Transporting the tumble dryer....................................................................................... 29
Levelling ........................................................................................................................ 30
Securing the tumble dryer against slipping .................................................................. 30
Electrical connection ......................................................................................................... 31
Supply air and exhaust air management........................................................................... 32
Ventilation...................................................................................................................... 32
Design of the exhaust air management system............................................................ 33
Calculating the total ducting length .............................................................................. 33
Exhaust duct dimensions.............................................................................................. 35
Exhaust air management with plug-in pipes................................................................. 35
Exhaust air management with flexible aluminium hose ................................................ 36
Shared exhaust air ducts .............................................................................................. 36
Gas .................................................................................................................................... 38
Connection and conversion instructions ...................................................................... 38
Tables ............................................................................................................................ 39
Connectivity ..................................................................................................................... 42
Pairing instructions............................................................................................................ 42
Opening the supervisor level......................................................................................... 42
Establishing the network connection via WPS ............................................................. 42
Establishing the network connection via soft AP.......................................................... 42
Establishing the network connection using a LAN cable.............................................. 42
Technical data ................................................................................................................... 43
Technical data.................................................................................................................. 45
Warning and Safety instructions
4
It is essential to read these instructions.
Extended documentation
This document contains essential information. You can access the full operating instruc-
tions and other up-to-date documentation for your appliance on the Mielewebsite:
https://www.miele.co.uk/professional/user-manuals-177.htm
In order to access the documentation, you will need the model number or serial number
for your appliance. This information can be found on the appliance’s data plate.
This tumble dryer complies with all current local and national safety requirements. How-
ever, inappropriate use can lead to personal injury and damage to property.
Read the operating instructions carefully before using the tumble dryer. They contain im-
portant information on safety, installation, use and maintenance. This prevents both per-
sonal injury and damage to the tumble dryer.
In accordance with standard IEC60335-1, Miele expressly and strongly advises that you
read and follow the instructions in the chapter on installing the tumble dryer as well as
the safety instructions and warnings.
Miele cannot be held liable for damage caused by non-compliance with these instruc-
tions.
Keep these operating instructions in a safe place and pass them on to any future owner.
When instructing other people how to use the tumble dryer, they must be made aware of
these safety and warning instructions.
During installation, the technical regulations for gas installations as well as national and
regional building regulations, fire regulations and specifications from the relevant gas
supply companies must be adhered to.
When planning a gas-heated system, contact the relevant gas supply company and a
building regulations inspector.
In the event of a fault or when carrying out cleaning and maintenance, the on-site
manual gas shut-off valve and the shut-off device on the gas meter must be closed.
Warning and Safety instructions
5
Before completing commissioning, maintenance, conversion and repair work, all gas-
conducting components – from the manual shut-off valve to the burner jet – must be
checked for leaks. Particular attention must be paid to the measurement connections on
the gas valve and on the burner. Checks must be performed when the burner is both
switched on and switched off.
Carry out an annual visual inspection of the gas supply and gas products in the prop-
erty. This inspection must comply with applicable national regulations.
Take these safety precautions if you smell gas
- Extinguish all flames immediately.
- Close the on-site gas shut-off device, the gas shut-off device on the gas meter or the
main gas shut-off device immediately.
- Open all windows and doors immediately.
- Do not light any naked flames (e.g. matches or lighters).
- Do not smoke.
- If there is the smell of gas in a room, never enter the room with a naked flame.
- Do not carry out any actions that will create electrical sparks (such as pulling out elec-
trical plugs or pressing electrical switches or bells).
- If you cannot find the cause of the gas smell and all gas valves have been shut off,
please call the gas supply company immediately.
If other persons are being shown how to operate the appliance, they must be given and/
or made aware of these important safety precautions.
Installation site
Gas-heated tumble dryers must not be operated in a room where cleaning machines oper-
ate with solvents containing perchloroethylene or CFCs. During combustion, any vapours
that are emitted will break down into hydrochloric acid, leading to consequential damage
affecting laundry and the appliance. Air exchange must not take place if appliances are set
up in separate rooms.
Rooms with fuel-burning installations must be adequately aerated and ventilated. Any gas-
heated appliance must be considered to be a fuel-burning installation (regardless of its gas
flow rate).
If no low pressure occurs when a full fire is burning in all fuel-burning installations, this
means that the room ventilation is working properly, even if the exhaust gases from the in-
stallations are being extracted mechanically. This ensures that the gas is being combusted
correctly and that the exhaust gases are being evacuated completely.
It must not be possible to seal off aeration and ventilation openings.
Before completing commissioning, maintenance, conversion and repair work, all gas-
conducting components – from the manual shut-off valve to the burner jet – must be
checked for leaks.
Particular attention must be paid to the measuring stubs on the gas valve. Checks must
be performed when the burner is both switched on and switched off.
Warning and Safety instructions
6
Appropriate use
The tumble dryer is intended for installation in a commercial environment.
This tumble dryer is only intended for drying fabrics which have been washed in a water
solution, and marked on the manufacturer's care label as being suitable for tumble drying.
“Dry cleaning kits” for freshening up garments in a tumble dryer are increasingly available
on the market. If using, do so at your own risk, and follow the instructions provided on the
packaging. Any other applications may be dangerous. Miele cannot be held liable for dam-
age resulting from incorrect or improper use or operation.
The tumble dryer is not intended for outdoor use.
The tumble dryer must not be used in a non-stationary location (e.g. on a ship).
Do not install the tumble dryer in a room where there is a risk of frost. At temperatures
around freezing point, the tumble dryer may not be able to operate properly. The permitted
room temperature is between 2°C and 40°C.
If the machine is used in a commercial environment it may only be operated by instruc-
ted/trained personnel. If the machine is used in a publicly accessible area, the supervisor
must ensure that it can be operated safely without risk of danger.
This appliance can only be used by people with reduced physical, sensory or mental
capabilities, or lack of experience or knowledge, if they are supervised whilst using it or
have been shown how to use it in a safe way and understand and recognise the con-
sequences of incorrect operation.
Children under 8 years of age must be kept away from the tumble dryer unless they are
constantly supervised.
Children 8 years and older may only use the tumble dryer unsupervised if they have
been shown how to use it safely and recognise and understand the consequences of in-
correct operation.
Children must not be allowed to clean or maintain the tumble dryer unsupervised.
Please supervise children in the vicinity of the tumble dryer and do not let them play
with it.
This tumble dryer may also be operated in public areas.
Any uses other than those listed above are prohibited. The manufacturer accepts no li-
ability in such cases.
Foreseeable misuse
Do not make any alterations to the tumble dryer, unless authorised to do so by Miele.
Do not lean on the tumble-dryer door. Otherwise, the tumble dryer may tip over, causing
injury to yourself or others.
Do not use a pressure washer or water jet to clean the tumble dryer.
The tumble dryer must be serviced in a timely and professional manner. Otherwise,
there is a potential risk of loss in performance, faults and fire.
Benzine, petrol, paraffin, or any easily flammable liquid must not be stored or used near
the machine. Danger of explosion.
Warning and Safety instructions
7
Do not expose the dryer to air which is contaminated with vapour of chlorine, fluorine or
other solvents. Danger of fire.
To prevent the risk of fire, the following items must not be dried in this tumble dryer:
- Items which have not been washed.
- Items which have not been thoroughly cleaned and are still soiled with grease, oil or
other deposits (such as kitchen linens or cosmetics cloths with cooking oils, grease, lo-
tions, etc). If items have not been thoroughly cleaned, there is a danger that they might
ignite when heated, even after they have been removed from the tumble dryer at the
end of the programme.
- Items (e.g. mops and floor cloths) that have been treated with inflammable cleaning
agents or which contain residues of acetone, alcohol, benzene, petrol, kerosene, stain
remover, turpentine, wax and wax remover or other chemicals.
- Items which have been splashed with hair lacquer, hair spray, nail varnish remover or
similar substances.
Wash heavily soiled items thoroughly by increasing the amount of detergent and selecting
a high washing temperature. If in doubt, wash the items several times.
Danger of squashing or cutting fingers etc. around the drum door hinges and the fluff fil-
ter cover. Use the appropriate handles and release catches only.
Always make sure that the drum is stationary before reaching in to remove laundry. Do
not touch the drum whilst it is still rotating.
In many programmes, the heating phase is followed by a cooling down phase to ensure
that the items are not too hot to handle when you remove them (this also avoids the
danger of the laundry self-igniting). The programme is not finished until the cooling down
phase is complete. Ensure that you always wait until the end of the programme before re-
moving the laundry.
Technical safety
This tumble dryer must only be set up and commissioned by a Miele Service technician
or authorised Miele Service Dealer.
Before installation check the tumble dryer for any obvious damage. A damaged tumble
dryer must not be installed and/or used.
Do not make any alterations to the tumble dryer, unless authorised to do so by Miele.
Do not connect the tumble dryer to the power supply by an extension lead (fire hazard
due to overheating).
Do not operate the tumble dryer in a room where cleaning machines operate with
solvents containing CFCs. During combustion, any vapours that are emitted will break
down into hydrochloric acid, leading to consequential damage affecting laundry and the
machine. Air exchange must not take place between rooms if machines are set up in sep-
arate rooms.
Fire hazard due to controllable socket. This tumble dryer must not be connected to a
controllable socket (e.g. a timer). There is a risk of the laundry self-igniting if the tumble
dryer’s cooling phase is interrupted.
Warning and Safety instructions
8
The electrical safety of this tumble dryer can only be guaranteed when correctly earthed.
It is essential that this standard safety requirement is met. If in any doubt, please have the
on-site wiring system tested by a qualified electrician. Miele cannot be held liable for the
consequences of an inadequate earthing system (e.g. electric shock).
The tumble dryer is only electrically disconnected from the power supply, if
- the plug has been disconnected from the socket.
- it is switched off at the main switch, or the mains electrical fuse is disconnected (on
site).
The plug must be easily accessible so that the tumble dryer can be disconnected from
the power supply at any time. The operator must be able to check from any access point
that the plug is still removed.
If the appliance is hard wired, adequate provision must be made on site to switch off all
poles to disconnect the tumble dryer from the power supply.
If the mains connection cable is faulty it must always be replaced by a Miele authorised
technician to protect the user from danger.
Tumble dryers with damage to the control panel or wire insulation must not be used until
they have been repaired.
Unauthorised repairs could result in unforeseen dangers for the user, for which Miele
cannot accept liability. Repairs should only be undertaken by a Miele authorised techni-
cian, otherwise any subsequent damage will not be covered by the warranty.
Faulty components may only be replaced by genuine Miele spare parts. Miele can only
guarantee the safety standards of the appliance when Miele replacement parts are used.
Only operate the tumble dryer when all removable outer panels are in place so that it is
impossible to touch an electrical component or moving part.
During the drying process, the door glass and the frame around the drum door will get
hot. Please be aware that the laundry may also be hot if it is removed from the tumble
dryer before the end of the drying programme.
To ensure the correct performance of the tumble dryer and to prevent the risk of faults
and fire, it is important to carry out maintenance on a regular basis.
In the event of a fault and for cleaning and maintenance purposes, the tumble dryer
must be disconnected from the power supply. The tumble dryer is only disconnected from
the power supply, if:
- It is switched off at the wall socket or the plug is withdrawn.
- The mains fuse is disconnected.
- The mains fuses have been completely removed.
The tumble dryer must not be used in non-stationary installation sites (e.g. on a ship).
Follow the instructions in “Installation” and “Technical data”.
The tumble dryer may only be operated when the ducting has been installed and the
room is sufficiently ventilated.
The vent ducting must never be installed in any of the following flues or shafts:
Warning and Safety instructions
9
- Chimneys or smokestacks that are in use.
- Shafts that are used to ventilate installation rooms with fireplaces.
- Flues that are used by third parties.
Smoke or exhaust gas that is fed back into the flue or shaft may be toxic.
Regularly check all components in the vent ducting (e.g. wall pipe, external grille, bends,
elbows, etc.) to make sure air can move through them and to ensure that they are working
properly. Clean components when necessary. Fluff deposits in the vent ducting system will
prevent the air from being extracted properly and, as a result, will stop the tumble dryer
from working properly.
If existing vent ducting is due to be used, it must be checked before being connected to
the tumble dryer.
Low pressure must not occur in the vent ducting.
There is a risk of suffocation and poisoning due to exhaust gases being sucked back if
gas-powered flow heaters, gas-powered room heaters, coal-burning stoves with a flue
connection, etc., are installed in the same room, in the same flat or in neighbouring rooms
and the negative pressure is 4Pa or more.
The following measures for suitable room ventilation (examples) can help to prevent negat-
ive pressure in the installation area:
- Install vents that cannot be closed in the exterior walls.
- Use window switches so that the tumble dryer can only be switched on when a window
is open.
Please always seek approval from your building regulations inspector to confirm that the
appliance can be operated without risk and that negative pressure of over 4Pa can be pre-
vented.
If multiple tumble dryers are to be connected to one vent ducting, a non-return flap must
be installed directly on the duct for each tumble dryer.
If this requirement is not observed, the tumble dryers may be damaged and their electrical
safety could be affected.
Follow the instructions in “Installation of the ducting”.
Do not block the gap between the bottom of the tumble dryer and the floor with plinth
facings, deep pile carpet etc.
Ensure that no closeable door, sliding door or an oppositely hinged door is installed that
would hinder the drum door being opened in any way.
This tumble dryer is supplied with a special lamp to cope with particular conditions (e.g.
temperature, moisture, chemical resistance, abrasion resistance and vibration). This special
lamp must only be used for the purpose for which it is intended. It is not suitable for room
lighting. Replacement lamps may only be fitted by a Miele authorised technician or by the
Miele Customer Service Department.
Installing thermal shut-off equipment on site is recommended.
If gas-heated appliances are accessible to anyone, it is also necessary to check whether
a gas flow monitor needs to be used.
Warning and Safety instructions
10
Correct use
Do not lean on the tumble-dryer door. Otherwise, the tumble dryer may tip over, causing
injury to yourself or others.
Always close the drum door after each drying cycle. This will prevent:
- Children climbing into the tumble dryer or hiding things in it.
- Pets or other small animals climbing into the tumble dryer.
Do not use a pressure washer or water jet to clean the tumble dryer.
Keep the room where the tumble dryer is located free from dust and fluff. If the air that is
taken into the machine contains dirt particles, this can cause blockages. A fault may then
occur and there is a risk of fire.
Never operate the tumble dryer without the fluff filter or with a damaged fluff filter. This
could lead to malfunctions. Fluff can clog the air channels, heating elements and vent
ducting, which could result in a fire. In this case, stop the tumble dryer immediately and re-
place the damaged fluff filter.
The fluff filter must be cleaned on a regular basis.
To ensure problem-free operation of the tumble dryer:
- Clean the surface of the fluff filter after each drying cycle.
- In addition, the fluff filter and the air passages must be cleaned when prompted by the
display.
To prevent the risk of fire, the following items must not be dried in this tumble dryer:
- Items which have not been washed.
- Items which have not been thoroughly cleaned and are still soiled with grease, oil or
other deposits (such as kitchen linens or cosmetics cloths with cooking oils, grease, lo-
tions, etc). If items have not been thoroughly cleaned, there is a danger that they might
ignite when heated, even after they have been removed from the tumble dryer at the
end of the programme.
- Items (e.g. mops and floor cloths) that have been treated with inflammable cleaning
agents or which contain residues of acetone, alcohol, benzene, petrol, kerosene, stain
remover, turpentine, wax and wax remover or other chemicals.
- Items which have been splashed with hair lacquer, hair spray, nail varnish remover or
similar substances.
Wash heavily soiled items thoroughly by increasing the amount of detergent and selecting
a high washing temperature. If in doubt, wash the items several times.
Do not install the tumble dryer in a room where there is a risk of frost. At temperatures
around freezing point, the tumble dryer may not be able to operate properly. The permitted
room temperature is between 2°C and 40°C.
Remove all items from the pockets of the laundry to be dried (e.g. lighters, matches,
keys).
Warning and Safety instructions
11
In many programmes, the heating phase is followed by a cooling down phase to ensure
that the items are not too hot to handle when you remove them (this also avoids the
danger of the laundry self-igniting). The programme is not finished until the cooling down
phase is complete. Ensure that you always wait until the end of the programme before re-
moving the laundry.
Fire hazard due to controllable socket. This tumble dryer must not be connected to a
controllable socket (e.g. a timer). There is a risk of the laundry self-igniting if the tumble
dryer’s cooling phase is interrupted.
The programme ends when the cooling phase starts. Many programmes are followed by
the cooling phase to ensure that the items of laundry are kept at a temperature that will not
cause them damage (for instance to prevent the risk of the laundry self-igniting). Always re-
move all items of laundry from the tumble dryer immediately after the cooling phase.
Fabric conditioner and similar products must be used according to the instructions on
the manufacturer's packaging.
Benzine, petrol, paraffin, or any easily flammable liquid must not be stored or used near
the machine. Danger of explosion.
Do not expose the dryer to air which is contaminated with vapour of chlorine, fluorine or
other solvents. Danger of fire.
For tumble dryers with stainless steel surfaces:
The stainless steel surfaces must not come into contact with liquid cleaning and disinfect-
ing agents which contain chlorine or sodium hypochlorite. These agents can have a cor-
rosive effect on stainless steel.
Aggressive vapours containing chlorine can also be corrosive.
Do not store containers of these agents near the tumble dryer.
Accessories
Accessory parts may only be fitted when expressly approved by Miele. If other parts are
used, warranty, performance and product liability claims will be invalidated.
Make sure that you order the correct plinth for this tumble dryer (available from Miele as
an optional accessory).
Miele cannot be held liable for damage caused by non-compliance with these Warn-
ing and Safety instructions.
Decommissioning the tumble dryer
Before disposing of a tumble dryer, render the door lock inoperable so that children can-
not lock themselves in the machine by mistake and endanger their lives.
Description of the machine
12
PDR910 (gas-heated)
1
2
3
4
6
5
7
8
9
10
11
aControl panel with touch display
bDoor
cFluff filter flap
d4 height-adjustable screw feet
eElectrical connection
fCommunication module slot
gIntake vents for drying air
hGas connection1/2" acc. to ISO7-1
iExhaust duct Ø100mm
jConnection for communication box
kCommunication box (optional)
For setting up a connection with external systems
Operating the tumble dryer
13
Control panel
aLanguage sensor control
For selecting the current user language
At the end of the programme, the language is automatically reset to the language set at
the supervisor level.
bBack sensor control
Takes you back one level in a menu.
cTouch display
d/sensor control
For starting the selected drying programme and cancelling a programme once it has
started. The programme selected can be started as soon as the sensor control starts
flashing.
eOptical interface
Used for data transfer by the Customer Service Department.
fbutton
For switching the tumble dryer on and off. Depending on the programming at supervisor
level, the tumble dryer switches off automatically to save energy. It is switched off an
adjustable time after the end of the programme/Anti-crease phase, or after being
switched on if no further selection is made.
Operating the tumble dryer
14
Sensor controls and touch display with sensor controls
The sensor controls, and Start/Stop and the sensor controls in the display re-
spond to finger tip contact. Every touch of a sensor control is confirmed with an audible
keypad tone. You can adjust the volume of the keypad tone or switch it off (see “Super-
visor level”).
The control field with sensor controls and the touch display can be scratched by pointed
or sharp objects, e.g. pens.
Only touch the control field with your fingers.
Main menu
After switching on the tumble dryer, the main menu will appear in the display. You can ac-
cess all the important submenus from the main menu.
Touch the sensor control at any time to return to the main menu. Values set previously
are not saved.
11:02
Programmes
Favourites
Supervisor
Help
Main menu
“Programmes” menu
In this menu, you can select the drying programmes.
“Favourites” menu
In this menu, you can select 1favourite programme from a total of 12favourite pro-
grammes. The drying programmes can be set up and saved by the supervisor in the Fa-
vourites menu (see “Favourite programmes” under “Supervisor level”).
“Supervisor” menu
You can alter the tumble dryer’s electronic module to suit changing requirements in the su-
pervisor level (see “Supervisor level”).
Operating examples
Selection lists
Scrolling through the “Programmes” menu (single selection)
11:02
Cottons
Programmes
Cottons PRO Minimum iron Delicates
Cottons Woollens
Operating the tumble dryer
15
To scroll through the menu, place your finger on the touch display and move it left or
right.
The orange scroll bar in the bottom display area shows that there are further options to
choose from.
To select the required drying programme, touch the programme name with your finger.
The display will now change to the standard menu for that programme.
“Extras” menu (multiple selection)
11:02
Gentle tumble
Extras
OK
Anti-crease
To select one or more Extras, touch the required Extras with your finger.
Currently selected Extras are marked orange. To deselect an Extra simply touch the Extra
again.
Setting numerical values
You can set numerical values in some menus. You can set the numerical values by swip-
ing your finger up and down on the display.
10
11
13
14
12 00
59
58
01
02
Clock display
OK
Place your finger on the number that you want to change.
To set the required number, swipe your finger up or down on the display.
Confirm the set numerical value by touching the OKsensor control.
Tip: For some settings, depending on the value range and increments, the value can also
be set using a numerical keypad. Briefly touching the numbers will bring up the numerical
keypad. Once a valid number has been entered, the OKsensor control will be highlighted
green.
12 00
11 59
10 58
13 01
14 02
Clock display
OK
Briefly touch a number between the two lines with your finger.
Operating the tumble dryer
16
The numeric block will appear.
12:00
3
4
21
5 6
7
8
0
9
Clock display
OK
To enter the numerical value, touch the numbers on the right-hand side and then confirm
with OK.
Pull-down menu
The pull-down menu can be used to display information (e.g. about a drying programme).
11:02
Time left h
2:27
Status
Cottons Drying
If an orange bar appears at the top of the screen in the middle of the display, you can open
the pull-down menu. Touch the bar and drag it down with your finger on the display.
To close the pull-down menu again, touch the orange bar and drag it up with your finger on
the display.
Exiting the menu
Touch the sensor control to return to the previous screen.
Entries made before this which have not been confirmed withOK will not be saved.
Operating the tumble dryer
17
Help display
With some menus, Help appears along the bottom line of the display.
If you need more information about the current menu, touch the Helpsensor control.
The additional information is shown in the display.
Touch the sensor control to return to the previous screen.
Drying
18
1. Notes on correct laundry care
Washing before
drying
Heavily soiled laundry must be washed particularly thoroughly. Use
sufficient detergent and select a high wash temperature. If in doubt,
wash the items several times.
The tumble dryer must not be used for drying items of laundry
which have been cleaned using industrial chemicals.
New and coloured items must be washed thoroughly and separately.
Do not dry new and coloured items with light coloured garments.
There is the risk of colours running and discolouring other garments
or even plastic components in the tumble dryer. Dark coloured fluff
can also settle on light coloured garments and vice versa.
Removing foreign
objects
Before drying, ensure that there are no foreign objects in the laundry.
Damage due to foreign objects which were not removed from
the laundry.
Foreign objects in the laundry can melt, burn or explode.
Ensure that any foreign objects (e.g. detergent dispensing aids,
lighters, etc.) have been removed from the laundry.
Check seams and stitching to ensure that the items of laundry are in-
tact. This way you will avoid the danger of fillings coming out and
causing a fire. Sew in or remove underwiring from bras.
Risk of fire due to incorrect use and operation.
The laundry can burn and destroy the tumble dryer and the sur-
roundings.
See the section on “Warnings and safety notes” for further informa-
tion.
Care symbols Drying
Normal/higher temperature
Low temperature*
* Select Low temperature.
Do not tumble dry
Ironing
Very hot
Hot
Warm
Do not iron
Drying
19
2.Loading the tumble dryer
Loading laundry
into the tumble
dryer
Textiles may be damaged.
Before loading, read chapter “1. Notes on correct laundry care”
first.
Open the door.
Load laundry into the tumble dryer.
Risk of damage with laundry getting trapped.
Laundry can be damaged by getting trapped when closing the
door.
When closing the door, make sure that laundry does not get
trapped in the door opening.
Do not overload the drum. Overloading can cause unnecessary wear
and tear to the laundry and cause a disappointing drying result. It
can also cause more creasing.
Closing the door Damage caused by laundry getting trapped.
Laundry can be damaged by getting trapped when closing the
door.
When closing the door, make sure that laundry does not get
trapped in the door opening.
Shut the door gently.
3. Selecting a programme
Switching on the
tumble dryer
Press the button.
The welcome screen will light up.
There are different ways to select a drying programme in the main
menu.
11:02
Programmes
Favourites
Supervisor
Help
Touch the Programmessensor control.
11:02
Cottons
Programmes
Cottons PRO Minimum iron Delicates
Cottons Woollens
Drying
20
With your finger, swipe to the left until you reach the required pro-
gramme.
Touch the sensor control for that programme.
The display will change to the standard menu for that drying pro-
gramme.
Alternatively, you can select a programme from the Favourites list.
The preset programmes under Favourites cannot be changed via
the Supervisor level.
11:02
Programmes
Favourites
Supervisor
Help
Touch the Favouritessensor control.
11:02
Favourites
Cottons
Cottons
Cottons
Delicates
With your finger, swipe to the left until you reach the required pro-
gramme.
Touch the requiredprogramme.
The display will change to the standard menu for that drying pro-
gramme.
4. Selecting programme settings
Select the drying
level With many programmes, you can change the preset drying level. De-
pending on the programme, you can select different drying levels.
Selecting extra
options The drying programmes can be augmented with various Extras.
Some Extras can only be selected for certain drying programmes.
11:02
0:57
8,0
Drying temp.
°C
Extras
Weight
Normal
Drying level
Cottons
66 not selected
kg
Overview
Touch the Extrassensor control.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/