Kingston Technology KVR13LE9/8 Datasheet

Kingston Technology
Brand
Kingston Technology
Model
KVR13LE9/8
Category
Memory modules
Type
Datasheet

Kingston Technology KVR13LE9/8 is an 8GB DDR3L-1333 CL9 SDRAM memory module. It is a 240-pin DIMM with ECC and low voltage. This memory module is designed for use in computers with DDR3L-1333 compatible motherboards. It has a JEDEC standard latency of 9-9-9 and operates at 1.35V or 1.5V. This memory module is also RoHS compliant and has a limited lifetime warranty.

Kingston Technology KVR13LE9/8 is an 8GB DDR3L-1333 CL9 SDRAM memory module. It is a 240-pin DIMM with ECC and low voltage. This memory module is designed for use in computers with DDR3L-1333 compatible motherboards. It has a JEDEC standard latency of 9-9-9 and operates at 1.35V or 1.5V. This memory module is also RoHS compliant and has a limited lifetime warranty.

KVR13LE9/8
8GB 2Rx8 1G x 72-Bit PC3L-10600
CL9 240-Pin ECC DIMM
DESCRIPTION
This document describes ValueRAM's 1G x 72-bit (8GB)
DDR3L-1333 CL9 SDRAM (Synchronous DRAM), 2Rx8, ECC,
low voltage, memory module, based on eighteen 512M x 8-bit
FBGA components. The SPD is programmed to JEDEC stan-
dard latency DDR3-1333 timing of 9-9-9 at 1.35V or 1.5V. This
240-pin DIMM uses gold contact fingers. The electrical and
mechanical specifications are as follows:
FEATURES
• JEDEC standard 1.35V (1.28V ~ 1.45V) and 1.5V (1.425V ~
1.575V) Power Supply
• VDDQ = 1.35V (1.28V ~ 1.45V) and 1.5V (1.425V ~ 1.575V)
• 667MHz fCK for 1333Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 9, 8, 7, 6
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• Programmable CAS Write Latency(CWL) = 7 (DDR3-1333)
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or
MRS]
• Bi-directional Differential Data Strobe
• Thermal Sensor Grade B
• Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
• On Die Termination using ODT pin
• Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°C
• Asynchronous Reset
• PCB: Height 1.18” (30mm), double sided component
Document No. VALUERAM1308-001.A00 04/12/13 Page 1
Memory Module Specifi cations
Continued >>
SPECIFICATIONS
CL(IDD) 9 cycles
Row Cycle Time (tRCmin) 49.5ns (min.)
Refresh to Active/Refresh 260ns (min.)
Command Time (tRFCmin)
Row Active Time (tRASmin) 36ns (min.)
Maximum Operating Power (1.35V) = 1.980 W*
(1.50V) = 2.200 W*
UL Rating 94 V - 0
Operating Temperature 0
o
C to 85
o
C
Storage Temperature -55
o
C to +100
o
C
*Power will vary depending on the SDRAM.
Document No. VALUERAM1308-001.A00 Page 2
Units: millimeters
30.00
18.80
15.80
11.00
8.00
0.00
133.35
0.00
54.70
TECHNOLOGY
MODULE DIMENSIONS:
  • Page 1 1
  • Page 2 2

Kingston Technology KVR13LE9/8 Datasheet

Kingston Technology
Brand
Kingston Technology
Model
KVR13LE9/8
Category
Memory modules
Type
Datasheet

Kingston Technology KVR13LE9/8 is an 8GB DDR3L-1333 CL9 SDRAM memory module. It is a 240-pin DIMM with ECC and low voltage. This memory module is designed for use in computers with DDR3L-1333 compatible motherboards. It has a JEDEC standard latency of 9-9-9 and operates at 1.35V or 1.5V. This memory module is also RoHS compliant and has a limited lifetime warranty.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers