Frigidaire SGER341AS0 User manual

Brand: Frigidaire

Model: SGER341AS0

Category: Tumble dryers

Type: User manual

This manual is also suitable for

For your safety the information in

this manual must be followed to minimize the risk

of fire or explosion or to prevent property damage,

personal injury or loss of life.

- Do not store or use gasoline or other flammable

vapors and liquid in the vicinity of this or any other

appliance.

- WHAT TO DO IF YOU SMELL GAS

· Do not try to light any appliance.

· Do not touch any electrical switch; do not use

any phone in your building.

· Clear the room, building or area of all

occupants.

· Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier's

instructions.

· If you cannot reach your gas supplier, call the

fire department.

Installations must be performed by a qualified or

licensed contractor, plumber, or gasfitter qualified

or licensed by the state, province, or region where

this appliance is being installed.

Contents

SUBJECT PAGE

Pre-Installation Requirements 2

Electrical Requirements 2

Exhaust System Requirements 2-3

Gas Supply Requirements 3

Location of Your Dryer 4

Mobile Home Installation 5

Rough-In Dimensions 5-6

Unpacking 6

Reversing Door Swing 6

Electrical Installation 7

Grounding Requirements 7

Electrical Connections—3-wire 8

Electrical Connections—4-wire 8

Installation 9

Replacement Parts 9

Printed in U.S.A.

P/N 134296400A (0404)

Installation

Instructions

Gas & Electric

Dryer

Before beginning installation, carefully read these instructions. This will simplify the installation and ensure the dryer

is installed correctly and safely. Leave these instructions near the Dryer after installation for future reference.

NOTE: The electrical service to the Dryer must conform with local codes and ordinances and the latest edition of the

National Electrical Code, ANSI/NFPA 70 or in Canada, CSA C22.1 Canadian Electrical Code Part 1.

NOTE: The gas service to the Dryer must conform with local codes and ordinances and the latest edition of the

National Fuel Gas Code ANSI Z223.1 or in Canada, CAN/CGA B149.12.

NOTE: The Dryer is designed under ANSI Z 21.5.1 or ANSI/UL 2158 - CAN/CSA C22.2 (latest editions) for HOME USE only.

This Dryer is not recommended for commercial applications such as restaurants or beauty salons, etc.

POWER SUPPLY CORD - The dryer is equipped with a 120 volt

3-wire power cord.

NOTE: Do not underNOTE: Do not under

NOTE: Do not under

any circumstancesany circumstances

any circumstances

remove groundingremove grounding

remove grounding

prong from plug.prong from plug.

prong from plug.

GASGAS

GAS

Dryer Dryer

Dryer

CIRCUIT - Individual 15 amp. branch circuit fused with a 15

amp. maximum time delay fuse or circuit breaker.

POWER SUPPLY - 3 wire, 120 volt single phase, 60 Hz,

Alternating Current.

OUTLET

RECEPTACLE

(COPPER)

3 WIRE GROUNDED NEUTRAL

120-240 VOLT 60 CYCLE

MAIN FUSE BOX

30 AMP DELAYED ACTION

FUSES

OR CIRCUIT BREAKER

NEUTRAL WIRE

NEMA 10-30R (COPPER)

SUBJECT TO LOCAL REGULATIONS

POWER SUPPLY

GROUNDING PRONGGROUNDING PRONG

GROUNDING PRONG

EXHAUST SYSTEM REQUIREMENTS

Use only 4 inch (10.2 cm) diameter (minimum) rigid or flexible

metal duct and approved vent hood which has a swing-out

damper(s) that open when the dryer is in operation. When the

dryer stops, the dampers automatically close to prevent drafts

and the entrance of insects and rodents. To avoid restricting the

outlet, maintain a minimum of 12 inches (30.5 cm) clearance

between the vent hood and the ground or any other obstruction.

The following are specific requirements for

proper and safe operation of your dryer. Failure to follow

these instructions can create excessive drying times and

fire hazards.

Do not use plastic flexible duct to exhaust the dryer.

Excessive lint can build up inside exhaust system and create a

fire hazard and restrict air flow. Restricted air flow will increase

dryer times. If your present system is made up of plastic duct or

metal foil duct, replace it with a rigid or flexible metal duct.

Ensure the present duct is free of any lint prior to installing

dryer duct.

If the dryer is not exhausted outdoors, some fine lint will be

expelled into the laundry area. An accumulation of lint in any

area of the home can create a health and fire hazard. The

dryer exhaust system MUST be exhausted to the outside

of the dwelling!

Do not allow combustible materials (for example: clothing,

draperies/curtains, paper) to come in contact with exhaust

system. The dryer MUST NOT be exhausted into a chimney, a

wall, a ceiling, or any concealed space of a building which can

accumulate lint, resulting in a fire hazard.

Exceeding the length of duct pipe or number of elbows

allowed in the "MAXIMUM LENGTH" charts can cause an

accumulation of lint in the exhaust system. Plugging the system

could create a fire hazard, as well as increase drying times.

Do not screen the exhaust ends of the vent system, nor use

any screws or rivets to assemble the exhaust system. Lint can

become caught in the screen, on the screws or rivets, clogging

the duct work and creating a fire hazard as well as increasing

drying times. Use an approved vent hood to terminate the duct

outdoors, and seal all joints with duct tape. All male duct pipe

fittings MUST be installed downstream with the flow of air.

Explosion hazard. Do not install the dryer

where gasoline or other flammables are kept or stored. If the

dryer is installed in a garage, it must be a minimum of 18 inches

(45.7 cm) above the floor. Failure to do so can result in death,

explosion, fire or burns.

PRE-INSTALLATION REQUIREMENTS

Tools and Materials Required for Installation:

1. Phillips head screwdriver.

2. Channel-lock adjustable pliers.

3. Carpenter's level.

4. Flat or straight blade screwdriver.

5. Duct tape.

6. Rigid or flexible metal 4 inch (10.2 cm) duct.

7. Vent hood.

8. Pipe thread sealer (Gas).

9. Plastic knife.

ELECTRICAL REQUIREMENTS

ELECTRIC Dryer

CIRCUIT - Individual 30 amp. branch circuit fused with 30 amp.

minimum time delay fuses or circuit breakers.

POWER SUPPLY - 3 wire, 240 volt, single phase, 60 Hz,

Alternating Current. (Canada - 240 volt, single phase, 60 Hz,

Alternating Current.)

POWER SUPPLY CORD KIT - The dryer MUST employ a 3-

conductor power supply cord NEMA 10-30 type SRDT rated at

240 volt AC minimum, 30 amp., with 3 open end spade lug

connectors with upturned ends or closed loop connectors and

marked for use with clothes dryers. If being installed in a

manufactured (mobile) home, the dryer MUST employ a 4-

conductor power supply cord NEMA 14-30 type SRDT or ST (as

required) rated at 240 volt AC minimum, 30 amp., with 4 open

end spade lug connectors with upturned ends or closed loop

connectors and marked for use with clothes dryers. See

ELECTRICAL CONNECTIONS FOR A 4-WIRE SYSTEM.

(Canada - 4-wire power supply cord is installed on dryer.)

OUTLET RECEPTACLE - NEMA 10-30R receptacle to be located

so the power supply cord is accessible when the dryer is in the

installed position. (Canada - NEMA 14-30R receptacle.)

EXHAUST DIRECTION

All dryers shipped from the factory are set up for rear exhausting.

However, on electric dryers, exhausting can be to the right or

left side of the cabinet or the bottom of the dryer. On gas dryers,

exhausting can be to the right side of the cabinet or the bottom

of the dryer. Directional exhausting can be accomplished by

installing Exhaust Kit, P/N 131456800, available through your

parts distributor. Follow the instructions supplied with the kit.

EXHAUST DUCT LOCATING DIMENSIONS

GAS SUPPLY REQUIREMENTS

Replace copper connecting pipe that is not

plastic-coated. Stainless steel or plastic-coated brass MUST

be used.

1. Installation MUST conform with local codes, or in the absence

of local codes, with the National Fuel Gas Code, ANSI Z223.1

(latest edition) or in Canada, the current CAN/CGA B149.

2. The gas supply line should be of 1/2 inch (1.27 cm) pipe.

3. If codes allow, flexible metal tubing may be used to connect

your dryer to the gas supply line. The tubing MUST be

constructed of stainless steel or plastic-coated brass.

4. The gas supply line MUST have an individual shutoff valve.

5. A 1/8 inch (0.32 cm) N.P.T. plugged tapping, accessible for

test gauge connection, MUST be installed immediately

upstream of the gas supply connection to the dryer.

6. The dryer MUST be disconnected from the gas supply piping

system during any pressure testing of the gas supply piping

system at test pressures in excess of 1/2 psig (3.45 kPa).

7. The dryer MUST be isolated from the gas supply piping

system during any pressure testing of the gas supply piping

system at test pressures equal to or less than 1/2 psig (3.45

kPa).

INSTALL MALE FITTINGS IN CORRECT DIRECTION

In installations where the exhaust system is not described in the

charts, the following method must be used to determine if the

exhaust system is acceptable:

1. Connect an inclined or digital manometer between the

dryer and the point the exhaust connects to the dryer.

2. Set the dryer timer and temperature to air fluff (cool

down) and start the dryer.

3. Read the measurement on the manometer.

4. The system back pressure MUST NOT be higher than

0.75 inches of water column. If the system back

pressure is less than 0.75 inches of water column, the

system is acceptable. If the manometer reading is

higher than 0.75 inches of water column, the system is

too restrictive and the installation is unacceptable.

Although vertical orientation of the exhaust system is

acceptable, certain extenuating circumstances could affect the

performance of the dryer:

• Only the rigid metal duct work should be used.

• Venting vertical through a roof may expose the exhaust

system to down drafts causing an increase in vent

restriction.

• Running the exhaust system through an uninsulated area

may cause condensation and faster accumulation of lint.

• Compression or crimping of the exhaust system will cause

an increase in vent restriction.

The exhaust system should be inspected and cleaned a

minimum of every 18 months with normal usage. The more

the dryer is used, the more often you should check the

exhaust system and vent hood for proper operation.

CORRECTCORRECT

CORRECT

INCORRECTINCORRECT

INCORRECT

0 60 ft. (18.28 m) 48 ft.(14.63 m)

1 52 ft. (15.84 m) 40 ft.(12.19 m)

2 44 ft. (13.41 m) 32 ft. (9.75 m)

3 32 ft. (9.75 m) 24 ft. (7.31 m)

4 28 ft. (8.53 m) 16 ft. (4.87 m)

0 30 ft. (9.14 m) 18 ft. (5.49 m)

1 22 ft. (6.71 m) 14 ft. (4.27 m)

2 14 ft. (4.27 m) 10 ft. (3.05 m)

3 NOT RECOMMENDED

VENT HOOD TYPE

(Preferred)

MAXIMUM LENGTH

of 4” (10.2 cm) Dia. Flexible Metal Duct

Number

90°

Turns

4”

(10.2 cm)

Louvered

VENT HOOD TYPE

(Preferred)

Number

90°

Turns

MAXIMUM LENGTH

of 4” (10.2 cm) Dia. Rigid Metal Duct

4”

(10.2 cm)

Louvered

SAME AS OTHER SIDESAME AS OTHER SIDE

SAME AS OTHER SIDE

(9.5 cm)(9.5 cm)

(9.5 cm)

4 3/8"4 3/8"

4 3/8"

(11 cm)(11 cm)

(11 cm)

5 7/8"5 7/8"

5 7/8"

(15 cm)(15 cm)

(15 cm)

13 1/2"13 1/2"

13 1/2"

(34 cm)(34 cm)

(34 cm)

3 3/4"3 3/4"

3 3/4"

(9.5 cm)(9.5 cm)

(9.5 cm)

3 3/4"3 3/4"

3 3/4"

(9.5 cm)(9.5 cm)

(9.5 cm)

(6.35 cm)

2½"

(6.35 cm)

2½"

LOCATION OF YOUR DRYER

DO NOT INSTALL YOUR DRYER:

1. In an area exposed to dripping water or outside weather

conditions.

2. In an area where it will come in contact with curtains, drapes,

or anything that will obstruct the flow of combustion and

ventilation air.

3. On carpet. Floor MUST be solid with a maximum slope of 1

inch (2.54 cm).

INSTALLATION IN RECESS OR CLOSET

1. A dryer installed in a bedroom, bathroom, recess or closet,

MUST be exhausted outdoors.

2. No other fuel burning appliance shall be installed in the

same closet as the Gas dryer.

3. Your dryer needs the space around it for proper ventilation.

DO NOT INSTALL YOUR DRYER IN A CLOSET WITH A

SOLID DOOR.

NOTE:NOTE:

NOTE: Under counter and stack models - 0 inches (0 cm)

for sides, rear, and top.

CLOSET DOORCLOSET DOOR

CLOSET DOOR

1" (2.54 cm)1" (2.54 cm)

1" (2.54 cm)

0" (0 cm)0" (0 cm)

0" (0 cm)

0" (0 cm)0" (0 cm)

0" (0 cm)

1" (2.54 cm)1" (2.54 cm)

1" (2.54 cm)

4. A minimum of 120 square inches (774.2 square cm) of

opening, equally divided at the top and bottom of the door,

is required. Air openings are required to be unobstructed

when a door is installed. A louvered door with equivalent

air openings for the full length of the door is acceptable.

MINIMUM INSTALLATION CLEARANCES (Inches)

FRONT SIDES REAR TOP

Alcove or

Under counter 0 (0 cm) 0 (0 cm) 0 (0 cm) 15 (38.1 cm)

Closet 1 (2.54 cm) 0 (0 cm) 0 (0 cm) 15 (38.1 cm)

Closet door ventilation required: 2 louvered openings each 60

square inches (387 square centimeters) — 3 inches (7.6 cm)

from bottom and top of door.

THIS DRYER MUST BE EXHAUSTED OUTDOORS.

5. The following illustrations show minimum clearance

dimensions for proper operation in a recess or closet

installation.

0" (0 cm)0" (0 cm)

0" (0 cm)

0" (0 cm)0" (0 cm)

0" (0 cm)

UNDER COUNTER INSTUNDER COUNTER INST

UNDER COUNTER INST

ALLAALLA

ALLA

TIONTION

TION

If an under counter* installation is desired, the dryer MUST have a top sheet kitIf an under counter* installation is desired, the dryer MUST have a top sheet kit

If an under counter* installation is desired, the dryer MUST have a top sheet kit

installed, P/N 131629100. Kit is available frinstalled, P/N 131629100. Kit is available fr

installed, P/N 131629100. Kit is available fr

om an authorized parom an authorized par

om an authorized par

ts distributorts distributor

ts distributor

*Custom-sized countertop is required.*Custom-sized countertop is required.

*Custom-sized countertop is required.

60 SQ. IN.60 SQ. IN.

60 SQ. IN.

(387.1 SQ. CM)(387.1 SQ. CM)

(387.1 SQ. CM)

60 SQ. IN.60 SQ. IN.

60 SQ. IN.

(387.1 SQ. CM)(387.1 SQ. CM)

(387.1 SQ. CM)

15" (38.1 cm)15" (38.1 cm)

15" (38.1 cm)

0" (0 cm)0" (0 cm)

0" (0 cm)

ROUGH-IN DIMENSIONSROUGH-IN DIMENSIONS

ROUGH-IN DIMENSIONS

UNDER COUNTER & STACK MODELS

(2.54 cm)(2.54 cm)

(2.54 cm)

REAR VIEWREAR VIEW

REAR VIEW

36"36"

36"

(91.5 cm)(91.5 cm)

(91.5 cm)

(6.5 cm)(6.5 cm)

(6.5 cm)

(9.5 cm)(9.5 cm)

(9.5 cm)

ELECTRIC CONNECTIONELECTRIC CONNECTION

ELECTRIC CONNECTION

13 1/2"13 1/2"

13 1/2"

(34.4 cm)(34.4 cm)

(34.4 cm)

(68.3 cm)(68.3 cm)

(68.3 cm)

UNDERUNDER

UNDER

COUNTERCOUNTER

COUNTER

34 5/8"34 5/8"

34 5/8"

(87.9 cm)(87.9 cm)

(87.9 cm)

3/8" (0.96 cm) DIA.3/8" (0.96 cm) DIA.

3/8" (0.96 cm) DIA.

GAS PIPEGAS PIPE

GAS PIPE

(68.6 cm)(68.6 cm)

(68.6 cm)

3/4"3/4"

3/4"

(1.9 cm)(1.9 cm)

(1.9 cm)

SIDE VIEWSIDE VIEW

SIDE VIEW

4 3/8"4 3/8"

4 3/8"

(11.1 cm)(11.1 cm)

(11.1 cm)

47 1/2"47 1/2"

47 1/2"

(120.7 cm)(120.7 cm)

(120.7 cm)

OPTIONALOPTIONAL

OPTIONAL

VENT KNOCKOUTVENT KNOCKOUT

VENT KNOCKOUT

3 3/4"3 3/4"

3 3/4"

(9.5 cm)(9.5 cm)

(9.5 cm)

MOBILE HOME INSTALLATION

1. Dryer MUST be exhausted outside (outdoors, not beneath

the mobile home) using metal ducting that will not support

combustion. Metal ducting must be 4 inches (10.16 cm) in

diameter with no obstructions. Rigid metal duct is preferred.

2. If dryer is exhausted through the floor and area beneath

the mobile home is enclosed, the exhaust system MUST

terminate outside the enclosure with the termination

securely fastened to the mobile home structure.

3. When installing a gas dryer into a mobile home, a provision

must be made for outside make up air. This provision is to

be not less than twice the area of the dryer exhaust outlet.

4. This dryer MUST be fastened to the floor. Mobile Home

Installation Kit No. 169840 is available from your dealer.

5. Refer to pages 2 and 3 for other important venting

requirements.

6. Installation MUST conform to current Manufactured Home

Construction & Safety Standard (which is a Federal

Regulation Title 24 CFR-Part 32-80) or when such standard

is not applicable, with American National Standard for

Mobile Homes. In Canada, the CSA Z240 is applicable.

The dryer is designed under ANSI Z 21.5.1 for

HOME USE only.

REVERSING DOOR SWING

Your dryer is designed so the door swing may be reversed at

any time without additional parts. Conversion is accomplished

by transferring hinges to the opposite side of the cabinet.

To change the direction of the door opening:

1. Open the dryer door. Remove the four hinge hole plugs from

the left side of the door opening. Place nearby for future

installation. NOTE: You may need a plastic knife to help pull

out the plugs. Be careful not to scratch the paint.

2. Remove the four screws that secure the door hinges to the

dryer front panel (see below). NOTE: Remove one screw

from each of the two hinges first. Hold the door firmly before

removing the last two screws.

3. Rotate the door 180° and reinstall the door hinges to the

dryer front panel with the four screws.

4. Install the four hinge hole plugs in the open screw holes on

the right side of the door opening.

UNPACKING

1. Using the four shipping carton corner posts (two on each

side), carefully lay the dryer on its left side and remove foam

shipping base.

To prevent damage, do not use the control panel

as a means to pick up or move the dryer.

NOTE: On under counter model clothes dryers, the top panel

may be removed for installation.

2. Return the dryer to an upright position.

PACKING

FOAM

SHIPPING

REMOVE 4 SCREWS

(ONE FROM EACH

HINGE FIRST)

ROUGH-IN DIMENSIONSROUGH-IN DIMENSIONS

ROUGH-IN DIMENSIONS

TOP CONSOLE MODELS

(68.6 cm)(68.6 cm)

(68.6 cm)

SIDE VIEWSIDE VIEW

SIDE VIEW

OPTIONALOPTIONAL

OPTIONAL

VENT KNOCKOUTVENT KNOCKOUT

VENT KNOCKOUT

4 3/8"4 3/8"

4 3/8"

(11.1 cm)(11.1 cm)

(11.1 cm)

47 1/2"47 1/2"

47 1/2"

(120.7 cm)(120.7 cm)

(120.7 cm)

REAR VIEWREAR VIEW

REAR VIEW

(68.3 cm)(68.3 cm)

(68.3 cm)

(2.54 cm)(2.54 cm)

(2.54 cm)

(110.7 cm)(110.7 cm)

(110.7 cm)

(6.5 cm)(6.5 cm)

(6.5 cm)

(9.5 cm)(9.5 cm)

(9.5 cm)

3/8" (0.96 cm) DIA.3/8" (0.96 cm) DIA.

3/8" (0.96 cm) DIA.

GAS PIPEGAS PIPE

GAS PIPE

ELECTRIC CONNECTIONELECTRIC CONNECTION

ELECTRIC CONNECTION

13 1/2"13 1/2"

13 1/2"

(34.4 cm)(34.4 cm)

(34.4 cm)

3 3/4"3 3/4"

3 3/4"

(9.5 cm)(9.5 cm)

(9.5 cm)

36"36"

36"

(91.5 cm)(91.5 cm)

(91.5 cm)

ELECTRICAL INSTALLATION

ALL ELECTRIC Dryers

The following are specific requirements for

proper and safe electrical installation of your dryer. Failure

to follow these instructions can create electrical shock

and/or a fire hazard.

This appliance MUST be properly grounded. Electrical shock

can result if the dryer is not properly grounded. Follow the

instructions in this manual for proper grounding.

Do not use an extension cord with this dryer. Some extension

cords are not designed to withstand the amounts of electrical

current this dryer utilizes and can melt, creating electrical shock

and/or fire hazard. Locate the dryer within reach of the receptacle

for the length power cord to be purchased, allowing some slack

in the cord. Refer to the pre-installation requirements in this

manual for the proper power cord to be purchased.

A U.L. approved strain relief must be installed onto power

cord. If the strain relief is not attached, the cord can be pulled

out of the dryer and can be cut by any movement of the cord,

resulting in electrical shock.

Do not use an aluminum wired receptacle with a copper

wired power cord and plug (or vice versa). A chemical reaction

occurs between copper and aluminum and can cause electrical

shorts. The proper wiring and receptacle is a copper wired

power cord with a copper wired receptacle.

NOTE: Dryers operating on 208 volt power supply will have

longer drying times than operating on 240 volt power supply.

Canadian ELECTRIC Dryer

DANGER

Improper connection of the equipment

grounding conductor can result in a risk of electrical shock.

Check with a licensed electrician if you are in doubt as to whether

the appliance is properly grounded.

For a grounded, cord-connected dryer:

1. The dryer must be grounded. In the event of a malfunction

or breakdown, grounding will reduce the risk of electrical

shock by a path of least resistance for electrical current.

2. Since your dryer is equipped with a power supply cord having

an equipment-grounding conductor and a grounding plug,

the plug must be plugged into an appropriate outlet that is

properly installed and grounded in accordance with all local

codes and ordinances. If in doubt, call a licensed electrician.

ALL GAS Dryers

This dryer is equipped with a three-prong (grounding) plug for

your protection against shock hazard and should be plugged

directly into a properly grounded three-prong receptacle. Do

not cut or remove the grounding prong from this plug.

GROUNDING REQUIREMENTS

Non-Canadian ELECTRIC Dryer

DANGER

Improper connection of the equipment

grounding conductor can result in a risk of electrical shock.

Check with a licensed electrician if you are in doubt as to whether

the appliance is properly grounded.

For a grounded, cord-connected dryer:

1. The dryer MUST be grounded. In the event of a malfunction

or breakdown, grounding will reduce the risk of electrical

shock by a path of least resistance for electrical current.

2. If your dryer is equipped with a power supply cord having an

equipment-grounding conductor and a grounding plug, the

plug MUST be plugged into an appropriate, copper wired

receptacle that is properly installed and grounded in

accordance with all local codes and ordinances. If in doubt,

call a licensed electrician.

For a permanently connected dryer:

1. The dryer MUST be connected to a grounded metal,

permanent wiring system; or an equipment grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the appliance.

1. Remove the screw securing the

terminal block access cover to the

rear panel and remove cover.

2. Install a U.L. approved strain relief

connector in the entry hole on the

back panel.

3. Insert a NEMA 14-30 Type ST or SRDT, U.L. approved

power cord through the strain relief.

4. Attach the green power cord ground wire to the cabinet

with the green ground screw

5. Attach the white (neutral) wire from the power cord to the silver-

colored center terminal on the terminal block. Tighten the

screw securely.

6. Attach the red and black wires from the power cord to the

outer brass-colored terminals on the terminal block. Tighten

both screws securely.

7. Tighten the screws securing the cord restraint firmly against

the power cord.

8. Reinstall the terminal block access cover.

STRAIN

RELIEF

MOUNTING

BRACKET

NUT

TIGHTEN

NUT

TO THESE

THREADS

POWER

CORD

RED

WHITE

BLACK

TERMINAL BLOCK

SILVER TERMINAL

GREEN

GROUND

SCREW

GREEN POWER CORD

GROUND WIRE

GREEN

NEUTRAL

GROUND

WIRE

4. Thread a U.L. approved 30 amp power cord, NEMA 14-30

type ST or SRDT through the strain relief.

5. Attach the green power cord ground wire to the cabinet

with the green ground screw.

6. Attach the white (neutral) power cord conductor from the

power cord and the green ground wire from the dryer

harness to the silver-colored center terminal on the terminal

block. Tighten the screw securely.

7. Attach the red and black power cord conductors to the

outer brass-colored terminals on the terminal block.

Do not make a sharp bend or crimp wiring/

conductor at the connections.

8. Tighten the screws securing the cord restraint firmly against

the power cord.

9. Tighten the strain relief nut securely so the strain relief

does not turn.

10. Reinstall the terminal block access cover.

TYPICAL 4

CONDUCTOR CORD

RED 240V

BLACK 240V

WHITE NEUTRAL

GREEN GROUND

30 AMP NEMA 14-30 TYPE SRDT OR ST30 AMP NEMA 14-30 TYPE SRDT OR ST

30 AMP NEMA 14-30 TYPE SRDT OR ST

TYPICAL 4

CONDUCTOR

RECEPTACLE

POWER CORD

TIGHTEN NUT

TO THESE

THREADS

STRAIN

RELIEF

MOUNTING

BRACKET

GREEN

GROUND

SCREW

NUT

SILVER TERMINAL

GREEN

NEUTRAL

GROUND

WIRE

ELECTRICAL CONNECTIONS

FOR 3-WIRE SYSTEM

Non-Canadian ELECTRIC Dryer

1. Remove the screws securing the terminal block access cover

and the strain relief mounting bracket located on the back

of the dryer upper corner.

2. Install a U.L. approved strain relief into the power cord entry

hole of the mounting bracket. Finger tighten the nut only at

this time.

3. Thread a U.L. approved 30 amp. power cord, NEMA 10-30

Type SRDT, through the strain relief.

4. Attach the power cord neutral (center wire) conductor to

the silver colored center terminal on the terminal block.

Tighten the screw securely.

5. Attach the remaining two power cord outer conductors to

the outer brass colored terminals on the terminal block.

Tighten both screws securely.

Do not make a sharp bend or crimp wiring/

conductor at connections.

6. Reattach the strain relief mounting bracket to the back of

the dryer with two screws. Tighten screws securely.

7. Tighten the screws securing the cord restraint firmly against

the power cord.

8. Tighten the strain relief nut securely so that the strain relief

does not turn.

9. Reinstall the terminal block cover.

ELECTRICAL CONNECTIONS

FOR 4-WIRE SYSTEM

Non-Canadian ELECTRIC Dryer

1. Remove the screws securing the terminal block access cover

and the strain relief mounting bracket located on the back

of the dryer upper corner.

2. Install a U.L. approved strain relief in the entry hole of the

mounting bracket. Finger tighten the nut only at this time.

3. Remove the green neutral ground wire from the green

ground screw located above the terminal block.

INSTALLATION

1. GAS CONNECTION (Gas dryers only)

a. Remove the shipping cap from gas pipe at the rear of

the dryer.

NOTE: DO NOT connect the dryer to L.P. gas service without

converting the gas valve. An L.P. conversion kit must

be installed by a qualified gas technician.

b. Connect a 1/2 inch (1.27 cm) I.D. semi-rigid or approved

pipe from gas supply line to the 3/8 inch (0.96 cm) pipe

located on the back of the dryer. Use a 1/2 inch to 3/8

inch (1.27 cm to 0.96 cm) reducer for a connection.

Apply an approved thread sealer that is resistant to the

corrosive action of liquefied gases on all pipe connections.

c. Open the shutoff valve in the gas supply line.

d. Test all connections by brushing on a soapy water solution.

NEVER TEST FOR GAS LEAKS WITH AN OPEN FLAME.

2. Connect the exhaust duct to outside exhaust system. Use

duct tape to seal all joints.

3. With the dryer in its final position, adjust one or more of the

legs until the dryer is resting solid on all four legs. Place a

level on top of the dryer. THE DRYER MUST BE LEVEL

AND RESTING SOLID ON ALL FOUR LEGS.

4. Plug the power cord into a grounded outlet. NOTE: Check

to ensure the power is off at circuit breaker/fuse box before

plugging the power cord into the outlet.

5. Turn on the power at the circuit breaker/fuse box.

Before operating the dryer, make sure the dryer

area is clear and free from combustible materials, gasoline,

and other flammable vapors. Also see that nothing (such as

boxes, clothing, etc.) obstructs the flow of combustion and

ventilation air.

6. Run the dryer through a cycle check for proper operation.

NOTE: On gas dryers, before the burner will light, it is

necessary for the gas line to be bled of air. If the burner

does not light within 45 seconds the first time the dryer is

turned on, the safety switch will shut the burner off. If this

happens, turn the timer to "OFF" and wait 5 minutes before

making another attempt to light.

7. If your dryer does not operate, please review the "Avoid

Service Checklist" located in your Owner's Guide before

calling for service.

8. Place these instructions in a location near the dryer for future

reference.

NOTE: A wiring diagram is located inside the dryer console or

under the top panel.

REPLACEMENT PARTS

If replacement parts are needed for your dryer, contact the

source where you purchased your dryer.

Label all wires prior to disconnection when

servicing controls. Wiring errors can cause improper and

dangerous operation. Verify proper operation after servicing.

Destroy the carton and plastic bags after the

dryer is unpacked. Children might use them for play. Cartons

covered with rugs, bedspreads, or plastic sheets can become

airtight chambers causing suffocation. Place all materials in a

garbage container or make materials inaccessible to children.

The instructions in this manual and all other

literature included with this dryer are not meant to cover every

possible condition and situation that may occur. Good safe

practice and caution MUST be applied when installing, operating

and maintaining any appliance.

Frigidaire SGER341AS0 User manual

Brand: Frigidaire

Model: SGER341AS0

Category: Tumble dryers

Type: User manual

This manual is also suitable for

Download PDF

report

Frigidaire SGER341AS0 User manual

This manual is also suitable for

Frigidaire SGER341AS0 User manual

Related papers

Other documents