SoundMax SM-CMD3007 Owner's manual

Category
Car video systems
Type
Owner's manual

SoundMax SM-CMD3007 Multimedia DVD/CD/MP3 Receiver is a versatile device with a built-in 3" TFT display, offering a wide range of entertainment options for your car. With DVD, CD, and MP3 playback capabilities, you can enjoy your favorite audio and video content on the go. The unit also features USB and SD/MMC card slots, allowing you to connect external storage devices and access your music, videos, and images. Tune in to your preferred radio stations with the built-in FM/AM tuner and save your favorites for easy access.

SoundMax SM-CMD3007 Multimedia DVD/CD/MP3 Receiver is a versatile device with a built-in 3" TFT display, offering a wide range of entertainment options for your car. With DVD, CD, and MP3 playback capabilities, you can enjoy your favorite audio and video content on the go. The unit also features USB and SD/MMC card slots, allowing you to connect external storage devices and access your music, videos, and images. Tune in to your preferred radio stations with the built-in FM/AM tuner and save your favorites for easy access.

SM-CMD3007
MULTIMEDIA DVD/CD/MP3 RECEIVER with built-in 3” TFT display
Instruction manual
 DVD/CD/MP3-
 3” TFT-

2
Dear customer!
Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully
before connecting, operating and/or adjusting the product and keep the manual for reference in the future.
Table of contents
Table of contents............................................................................................... 2
Important safeguards......................................................................................... 3
Accessories....................................................................................................... 4
Installation/connection ....................................................................................... 5
Unit controls ....................................................................................................10
General operations............................................................................................14
Radio operations...............................................................................................17
Disc/USB/SD/MMC operations.............................................................................21
DVD Setup menu..............................................................................................26
Handling and cleaning discs................................................................................29
Troubleshooting guide .......................................................................................30
Specification ....................................................................................................31
3
Important safeguards
Read carefully through the manual to familiarize yourselves with this unit.
Keep this manual handy as a reference for operating procedures and precautions. Do not allow persons
who have not read through this manual to use this unit.
“CLASS 1 LASER PRODUCT”
This product contains a laser diode of higher class than 1. Laser beams from the optical pickup are
dangerous to the eyes. To ensure continued safety, do not remove any covers or attempt to gain
access to the inside of the product. Refer all servicing to qualified personnel.
Do not allow this unit to come into contact with liquids. Electrical shock could result. Also, damage to
this unit, smoke, and overheating could result from contact with liquids or dust. Protect this unit from
moisture.
Make sure that foreign objects do not get inside the unit; they may cause malfunctions, or create safety
hazards such as electrical shock or laser beam exposure.
The beginning of operation is the moment of the unit installation. Before use the device in winter it is
recommended to heat up the passenger compartment during 20 seconds or to the operation
temperature.
Using the unit with the temperature that goes beyond the operation temperature greatly decreases the
operation resource of the screen and other components of the unit and can result in an outage.
Disconnect the vehicle’s negative battery terminal while mounting and connecting the unit.
The unit is designed for negative terminal of the battery, which is connected to the vehicle metal.
Please ensure it before installation.
When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a
higher amperage rating may cause serious damage to the unit.
Do not allow the speaker wires to be shorted together when the unit is switched on. Otherwise it may
overload or burn out the power amplifier.
Make sure you disconnect the power supply and aerial if you will not be using the system for a long
period or during a thunderstorm.
4
Make sure you disconnect the power supply if the system appears to be working incorrectly, is making
an unusual sound, has a strange smell, has smoke emitting from it or liquids have got inside it. Let a
qualified technician check the system.
Always keep the volume low enough so that you can hear sounds from outside the vehicle.
Should this product fail to operate properly, contact your dealer or nearest service center.
Accessories
1. Receiver 1 pc
2. Remote controller 1 pc
3. Protective case for front panel 1 pc
4. ISO cable set (A+B) 1 pc
5. Mounting parts:
Mounting sleeve 1 pc
Flat washer 1 pc
Spring washer 1 pc
Nut 1 pc
Outer trim ring 1 pc
Release keys 2 pcs
Metal strap 1 pc
Screw 4 pcs
Rear mounting bolt 1 pc
Rubber cushion 1 pc
6. Consumer information 1 pc
7. Warranty card 1 pc
8. Instruction manual 1 pc
5
Installation/connection
Choose the mounting location where the unit will not interfere with the normal driving function of the
driver.
Before finally installing the unit, connect the wiring and make sure that the unit works properly.
Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the
vehicle.
Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.
If installation angle exceeds 30° from horizontal, the unit may not perform properly.
Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or
from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.
Din Front/Rear-Mount
This unit can be properly installed either from 'Front' (conventional DIN Front-mount) or 'Rear' (DIN Rear-
mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the
following illustrated installation methods.
DIN FRONT-MOUNT (Method A)
1. Car dashboard
2. Sleeve
3. Screw
4. Nut
5. Spring washer
6. Screw
7. Metal strap
8. Flat washer
6
1. Install the sleeve into the dashboard; ensure it is installed with the correct side and there are no
obstacles (wires, dashboard elements, etc) for the unit installation.
2. After installing the sleeve into the dashboard, bend tabs fitting to the size of
the dashboard to fix the sleeve in place.
3. Use the metal strap to fix the rear side of the unit. Determine a place for fixing
and install the strap as shown in the picture. You can bend the strap to the
needed angle with your hands.
4. Make the necessary wire connections. Ensure the connections are correct.
5. Install the unit into the sleeve until the side locks are fixed.
Dismantling the unit
– Trim frame
– Frame uninstall direction
– Release key insertion
1. Switch off the unit and detach the front panel.
2. Insert your fingers into the groove in the front side of the trim frame (apply
some effort to detach the frame). Pull the frame to detach it.
3. Insert the supplied release keys into the both sides of the unit body to click,
as shown in the picture. To extract the unit from the dashboard, pull the
release keys or the unit body to pull it out. Before detaching the unit, ensure
it is not fixed with the metal strap.
Trim frame installation
To install the trim frame, press it to the unit body and push it to fix it in place. This should be done before
installing the front panel; otherwise you are not able to install the trim frame. When the trim frame being
installed, the side with the groove should face down and fixed first.
7
2. DIN REAR-MOUNT (Method B)
For this method, use the screw holes in the lateral sides of the unit. Fix the unit with the help of the factory
radio mounting brackets.
1. Select a position in which the screw holes of the brackets (3) are aligned
with the screw holes in the unit body, and screw in two screws (2) in each side.
2. Screw.
3. Factory radio mounting brackets.
4. Vehicle dashboard.
5. Lock (remove this part).
Note: The outer trim frame and mounting sleeve are not used for method of installation.
Installing the front panel
Insert the left locker on the receiver into the left groove of the panel, and then insert the right locker into
the right groove. Lift the panel and press on the upper part of the panel until a click. Ensure the panel is
fixed properly, otherwise error symbols may be displayed or some buttons will not function.
To detach the front panel, press OPEN button. When the panel is in horizontal position, detach the left part
of the panel from the locker, and then detach the right part.
Anti-theft system
The front panel of this unit can be stored in the included protective case when not in used and carried away
when you leave the vehicle to deter theft.
Switch off the power of the unit. Detach the front panel, then put it to the protective case and take it with
you.
Cautions: The control panel can easily be damaged by shocks. After removing it, place it in a protective
case and be careful not to drop it or subject it to strong shocks.
The rear connector that connects the main unit and the control panel is an extremely important part. Be
careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc.
Note: If the control panel is dirty, wipe off the dirt with soft, dry cloth only. And use a cotton swab soaked
in isopropyl alcohol to clean the socket on the back of the control panel.
8
Electrical Connection
Connector A Connector B
1. - 1. Rear right speaker (+)
2. - 2. Rear right speaker (-)
3. - 3. Front right speaker (+)
4. Memory +12V 4. Front right speaker (-)
5. Auto antenna output 5. Front left speaker (+)
6. - 6. Front left speaker (-)
7. +12V (to ignition key) 7. Rear left speaker (+)
8. Ground 8. Rear left speaker (-)
9
ISO Connection table
FunctionLocation
Connector A Connector B
1 - Rear right (+) - Purple
2 - Rear right (-) - Purple/Black
3 - Front right (+) - Grey
4 Battery +12V/Yellow Front right (-) - Grey/Black
5 Auto Antenna - Blue Front left (+) - White
6 - Front left (-) - White/Black
7 Ignition/Red Rear left (+) - Green
8 Ground/Black Rear left (-) - Green/Black
Note: Power antenna wire is intended for power supply of the antenna and for remote control of an
additional amplifier.
Parking wire connection
If Parking cable is connected to hand brake switch, the video display of the TFT monitor will be controlled by
driving status, system setup and input video sources. When the car is moving ahead, if the video disc is
played, the screen shows “Attention! You cannot use this function while driving”, and blank screen. The
above warning screen will prevent the driver from watching images.
10
Unit controls
Front panel
1. IR sensor
2. 1/PLAY/PAUSE button
3. POWER/MUTE button
4. MODE button
5. VOLUME+ button
6. MENU button
7. BND button
8. 6/DIR+ button
9. NEXT button
10. TFT display
11. OPEN button
12. USB port
13. PREVIOUS button
14. 2/INT button
15. 3/RPT button
16. OK button
17. VOLUME- button
18. AS/PS button
19. 4/RDM button
20. 5/DIR- button
21. A/V in jack
11
Inner panel
1. Memory card slot
2. Eject button
3. Panel status indicator
4. RESET button (hole)
5. Disc loading slot
Pressing RESET hole will erase the clock setting and stored stations.
Panel status indicator lights up when you flip down the panel and flashes when you remove the panel.
12
Remote controller (RC)
1. MODE button
2. PWR button
3. BND/RDM button
4. ENTER button/Cursor buttons
5. STEREO/MONO button
6. PTY/PROG button
7. P.SCN/RPT button
8. SEEK-/PREVIOUS button
9. AF/TA button
10. STOP/PBC button
11. OSD button
12. Number buttons
13. PLAY/PAUSE button
14. MUTE button
15. MENU button
16. SUB-T button
17. SETUP button
18. ANGLE button
19. INT button
20. A-B/ZOOM button
21. VOL+ button
22. SEEK+/NEXT button
23. SEL button
24. AUDIO/GOTO button
25. VOL- button
13
Changing the battery
1. Press the catch and at the same time pull out the battery tray (pic. 1).
2. Insert the 1 lithium battery, type CR2025 (3V) battery with the stamped
(+) mark facing upward. Insert the battery tray into the remote controller
(pic.2).
Warning:
Store the battery where children cannot reach. If a child accidentally swallows the battery, consult a
doctor immediately.
Do not recharge, short, disassemble or heat the battery or dispose it in a fire.
Do not expose or bring into contact the battery with other metallic materials. Doing this may cause the
battery to give off heat, crack or start a fire.
When throwing away or saving the battery, wrap it in tape and insulate; otherwise, the battery may
give off heat, crack or start a fire.
Please direct the Remote controller to the IR sensor of the front panel.
Pic. 1 Pic. 2
14
General operations
Reset the unit
Operating the unit for the first time or after replacing the car battery, you must reset the unit. Press RESET
button (hole) with a pointed object (such as a ballpoint pen) to set the unit to initial state.
Note: When some errors occur, you can also press RESET button to resume to normal, and it will erase the
clock setting and some memorized functions.
Turning the unit on/off
Press any button on the panel or the RC (except OPEN button) to turn on the unit. Press and hold
POWER/MUT button on the panel or press POWER button on the RC to turn off the unit.
Mode selection
Repeatedly press MODE button on the RC or on the panel to select a mode: Tuner => DVD => USB =>
Card => AV IN.
Note: The DVD, Card and USB modes are only available when corresponding storages are inserted into the
unit.
Mute function
Press MUTE button on the RC or POWER/MUT button on the panel to turn off the sound. “MUTE” appears on
the TFT. Press the button again or adjust volume to resume the sound output.
Volume control
Press VOL+/VOL- buttons on the RC or VOLUME+/VOLUME- buttons on the panel to decrease or increase
sound volume level.
Setting the sound characteristics
Press and hold OK button on front panel or press SEL button on the RC to select the audio setting menu:
BASS =>TREBLE => BALANCE => FADER => EQ. Press UP/DOWN cursor buttons on the RC or VOLUME+/-
15
button on the panel to select the audio setting item. Press ENTER button or RIGHT cursor button on the RC
or OK button on the panel to enter the selected item.
Press LEFT/RIGHT buttons on the RC or VOLUME+/VOLUME- buttons on the panel to adjust the audio
setting. Press and hold OK button on the panel or press SEL button on the RC again to save the setting and
return to current mode.
Note: If turn off the power, all the settings of each mode will be saved. If turn off the ACC power, all the
settings will be clear and become factory default setting. If you don’t adjust setting within 3 seconds after
selecting the desired setting item, the unit will automatically return to the current mode.
System setup
Press MENU button on the panel or RC to enter Setting Menu. Press UP/DOWN cursor buttons on the RC or
VOLUME+/- buttons on the panel to select a menu page. Press ENTER button or RIGHT cursor button on the
RC or press OK button on the panel to enter the page. Press LEFT/RIGHT cursor buttons on the RC or
VOLUME+/VOLUME- buttons on the panel to select an item, then press OK button on the RC or SEL button
on the panel to adjust the setting.
Press ENTER button or RIGHT button on the RC or OK button on the panel to confirm, press MENU button to
return to last settings list.
AUDIO MENU
Bass: Support 10 levels. Default level is 0.
Treble: Support 10 levels. Default level is 0.
Balance: Support 10 levels for each left and right channel. Default is left equal to right.
Fader: Support 10 levels for each front and rear channel. Default is front equal to rear.
EQ DSP: FLAT => CLASSICS => POP => ROCK => DSP OFF.
PICTURE MENU
(available in DVD/USB/Card modes only)
Red: Adjust level of red color. Support 50 levels. Default level is 25.
Green: Adjust level of green color. Support 50 levels. Default level is 25.
Blue: Adjust level of blue color. Support 50 levels. Default level is 25.
Brightness: Adjust level of screen brightness. Support 50 levels. Default level is 25.
Contrast: Adjust level of screen contrast. Support 50 levels. Default level is 25.
16
Sharpness: Adjust level of screen sharpness. Support 15 levels. Default level is 10.
Screen: Adjust screen aspect: 16:9 => 4:3 => FULL.
Color reset: Resume color default status. (Select YES or NO with cursor buttons, press ENTER button on
the RC or OK button on the panel to confirm).
EXPERT MENU
DX: Set search radio station by DX or LOCAL mode. DX => LOCAL.
Stereo: Set radio audio at STEREO or MONO mode, STEREO => MONO.
Beep: Set press keys’ sound. 2ND => ALL => OFF.
Loud: Set loudness on or off. OFF => ON.
Backlight: Set OSD backlight: HIGH => LOW => MID.
OSD color: Set OSD color: DARK BLUE => VIOLET => LIGHT BLUE.
CLOCK MENU
Clock: Set CLOCK display time or not. OFF/ON.
Clock Hour: set clock 12H/24H.
Clock adjust: Set CLOCK ADJUST time.
17
Radio operations
Band selection
Press BND/RDM button on the RC or BND button on the panel to switch to the bands in the following order:
FM1 - FM2 - FM3 (OIRT) – MW (AM).
Manual/automatic tuning
Manual tuning: Press and hold PREVIOUS/NEXT buttons on the RC or panel to enter manual tuning
mode. MANUAL will be displayed. Press these buttons repeatedly to change the frequency upward or
downward step by step.
Automatic tuning: Press repeatedly PREVIOUS/NEXT buttons on the RC or panel to start automatic
seeking for an available radio station downward or upward. After being found the station will be played.
To stop seeking, press one of these buttons again.
Programming stations
There are 6 numbered preset buttons, under which you can store and recall stations for each band (18 FM,
6 AM). Select the needed station, then press and hold a preset button. The station will be saved in the
memory under the corresponding number. To recall a stored station, press the corresponding preset button.
Auto memory store/Preset scan
Auto store: Select a band, press and hold AS/PS button on the panel or P.SCN/RPT button on the RC to
enter auto store mode. The radio will automatically store 6 stations to the 6 preset memories of the current
band. To stop auto store, press the button again.
Note: During auto station preset, the unit will search and store stations with the strong signal first, and
then weaker signal stations until the memories are full.
Preset scan: Select a band, press AS/PS button on the panel or P.SCN/RPT button on the RC to scan all
preset stations in the memories of the current band. To stop preset scan, press the button again.
18
Stereo/Mono reception
In FM mode, press STEREO/MONO button on the RC to select stereo or mono signal reception mode.
On-screen display
Press OSD button on the RC to show enabled PTY function icon.
RDS background
RDS service availability varies with areas. Please understand if RDS service is not available in you area, the
following service is not available.
AF (Alternative frequencies) function
Press and hold AF/TA button on the RC or BND button on the panel to enable AF function. When the radio
signal strength is poor, enabling the AF function will allow the unit to automatically search another station
with the same PI (Program Identification) as the current station but with stronger signal strength.
Note: AF indicator on the display will flash until RDS information is received. If RDS service is not available
in your area, turn off the AF mode.
TA (Traffic alarm) function
Press AF/TA button on the RC or press and hold MODE button on the panel to activate the traffic alarm
function.
When TA function is activated, it will search the station with TA information automatically. If there is no TA
information, it will search the station with TP information automatically, if there is no TP information either,
it will return to the previous station after searching.
When receiving the station with TP information but without TA information, TP icon is on and TA icon keeps
blinking; when receiving the station with TP and TA information, both TP and TA icons are on.
When playing in other mode and TA information is received, it will change to the radio mode automatically.
After playing over, it will return to the previous mode. Press AF/TA button on the RC or press and hold
MODE button on the panel once to ignore the received TA information, do it twice to turn off the function.
19
PTY (Program type) function
Press PTY/PROG button on the RC to open PTY program type list, and repeat pressing PTY/PROG button to
select a PTY type. After selecting the program type you want, press number buttons 1 - 6 on the RC or on
the panel to start search. Press it again to stop the PTY search. If PTY code is different or not available, "PTY
NONE" blinks on the display.
Other functions
Press MENU button on the panel or RC to enter Setting Menu. Press UP/DOWN cursor buttons on the RC or
VOLUME+/- buttons on the panel to select RDS SETUP page. Press ENTER button or RIGHT cursor button on
the RC or press OK button on the panel to enter the page. Press LEFT/RIGHT cursor buttons on the RC or
VOLUME+/VOLUME- buttons on the panel to select an item, and then press OK button on the RC or SEL
button on the panel to adjust the setting.
Press ENTER button or RIGHT cursor button on the RC or OK button on the panel to confirm, press MENU
button to return to last settings list.
RDS SETUP
TA ALARM/SEEK: In TA SEEK mode, the unit will seek for traffic announcement program; in TA ALARM
mode, the alarm is set off.
PI SOUND/MUTE: Choose either PI sound or PI mute. PI sound refers to the reception noise when the
AF function tries to scan alternative frequency.
RETUNE S/L: RETUNE refers to the time period the unit allows for radio scan when reception is
interrupted. SHORT represents a time period of 30 seconds and LONG represents a time period of 90
seconds.
MASK DPI/ALL: During MASK DPI mode, the unit will mask only the AF which has different PI, this is
the default mode; during MASK ALL mode, the unit will mask the AF which has different PI and no RDS
signal with high field strength.
EON TA DX/LOCAL: EON (Enhanced Other Networks) - This unit is equipped with the latest technology
of EON control, so that when you are listening to Radio or CD, if there is any travel announcement from
a nearby local station, the radio will already know the frequency of that radio station. Then it will
receive the station, turn up the volume, or interrupt the playback for the duration of the
20
announcement. At the end of the announcement the radio will return to its previous state ready for the
next announcement.
REG ON/OFF: When REG is available (On), the receiver accepts regional variants of the tuned station
display. When REG is unavailable (Off), the receiver ignores regional variants.
TA VOL: You can set the default volume of TA announcement. Support 50 levels. Default level is 50.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

SoundMax SM-CMD3007 Owner's manual

Category
Car video systems
Type
Owner's manual

SoundMax SM-CMD3007 Multimedia DVD/CD/MP3 Receiver is a versatile device with a built-in 3" TFT display, offering a wide range of entertainment options for your car. With DVD, CD, and MP3 playback capabilities, you can enjoy your favorite audio and video content on the go. The unit also features USB and SD/MMC card slots, allowing you to connect external storage devices and access your music, videos, and images. Tune in to your preferred radio stations with the built-in FM/AM tuner and save your favorites for easy access.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI