Optiview VR Series Quick start guide

Brand: Optiview

Model: VR Series

Category: Digital Video Recorders (DVR)

Type: Quick start guide

1. After unpacking the DVR, set it up on a sturdy shelf free from vibrations, dust, high humidity and

moisture.

2. Connect the following at the back of the computer:

a. PC USB mouse and keyboard – plug in the USB mouse at the USB ports

located at the back of the PC shown here below

b. PC power cable – plug it in at the back of the PC as shown here.

c. PC monitor – plug your PC monitor cable at the “VGA Out” as shown above.

3. Connect the Video cables from your cameras to the video pigtail connectors of the DVR system located at

the back panel of the DVR computer. Note that every pigtails are color coded, red colors are used for video

input and white (or white stripes) are for audio input. Every DVR pigtail cables are labeled as VID or AID

followed by a number, for example, VID1 or AID1 etc…. See the illustration below.

I. Get to know your connectors and back panel

Pigtail

label is

indicated

here

Video and

Audio 1-4

Video and

Audio 5-8

8 channel DVR

16 channel DVR

24/36 channel DVR 48/64 channel DVR

Video and

Audio 1-8

Video and

Audio 9-16

II. Starting your DVR System

1. After power cable, USB mouse, keyboard, monitor and all your camera cables have

been connected to the DVR system, you are now ready to turn ON your DVR

system.

Turn ON the main black color power

switch at the back of the computer,

the DVR will start to load the

software in a few moments.

2. The DVR settings was all preconfigured

at our facility to meet the optimum level

of performance. It is already set to

automatically record security video as

soon as the software finished loading on

your screen. It will record based on

motion detection to allow the system to

store more days of recorded video on

your hard drive at optimum level.

Top: Front power switch

Bottom: Reset power switch

3. Things you might want to customize or change on your DVR system:

a. setup up personalized username and password

b. setup the DVR on your private network

c. change the date/time of the DVR clock, including time zone.

Note: The DVR Serial number is located at the top right corner of the software or at the back

panel of the DVR box. You need to have this ready before you call for technical support at

904-855-1121. Your DVR CD copy will contain DVR manuals, software and training video to

learn more about your DVR.

III. Customize your DVR System: Create DVR User Accounts

A. Setup Personalized Username and Password

This task involves two way process.

First, we need to activate the DVR lock options, secondly, we will create the user

account with their username, password and assign user access rights which will limit

what they can do at the DVR system.

1. Activate the DVR Software Lock. Starting from the LIVE menu screen:

a. Click “Settings” button

b. Click “Password” button

c. Enable the DVR lock options as shown below:

Three most common things customized on a VR Enterprise DVR system:

A. setup up personalized username and password

B. setup the DVR on your private network

C. Change date and time clock of the DVR system

III. Customize your DVR System: Create DVR User Accounts

2. Create DVR User Account – below is the user graphics menu to add a DVR user account.

b. Enter the username, authority level and password for your new account as shown

below:

c. Assign your own preferred specific User Right and Setup rights for the new user

account.

User rights includes operational access right s usually granted to change specific

settings of the DVR systems

Setup Rights are access right to main menu before a user can get into the details

of the operations’ user access rights.

d. Press exit button to save the parameters, when prompted, “Save “ the settings

Note: password should

only be 8 characters

long. Do not use special

characters such as

)(*&^%$#@!

a. Click “New User”

button

B. Setup DVR on your private network

Note: This portion of information is provided by Optiview as a courtesy only. Optiview Inc. does not provide

detailed technical support in configuring private network devices like routers, similar network devices and/or problems in

configuring your local area network. If you encounter problems, please contact your network device manufacturer, Internet

Service Provider or Microsoft for technical support. If you need to have a detailed technical support in configuring your

private network, Optiview does offer a Networking Technical Support at the rate of $65.00 per hour (subject to change

without prior notice). This support requires the customer to have Internet subscription from your Internet Service provider

and a software will be installed on your computer to remotely configure your network devices (routers, modem etc…)

There are several process involved on this task which includes but not limited to:

* Connecting network cable of your DVR to you private

network device (routers or switch)

* Adding the DVR system to your local private network.

- Set a static IP address to you DVR system.

* Configure Network firewall for Port Forwarding

Here is a typical diagram how your network devices are interconnected:

1. Connecting network cables of DVR to your router/switch

a. Connect a CAT5 cable to your router or switch

b. Connect the opposite end of the CAT5 cable to your DVR computer through the network

port located at the back panel of the DVR computer.

IV. Customize your DVR System: Configure Network Setup

2. Setup a Static IP address to your DVR system

What is an IP address?

IP addresses also known as network address are four sets of numbers separated by periods

that allow computers to identify each other. Every computer has at least one IP address,

and two computers should never have the same IP address. If they do, neither of them will

be able to connect to the local network or Internet.

Dynamic vs. Static IPs Most routers assign dynamic IP addresses by default. They do this

because dynamic IP address networks require no configuration. The end user can simply

plug their computer in, and their network will work. When IP addresses are assigned

dynamically, the router is the one that assigns them. Every time a computer reboots it asks

the router for an IP address. The router then hands it an IP address that has not already

been handed out to another computer. This is important to note. When you set your

computer to a static IP address, the router does not know that a computer is using that IP

address. So the very same IP address may be handed to another computer later, and that

will prevent both computers from connecting to the internet. So when you assign a static IP

addresses, it's important to assign an IP address that will not be handed out to other

computers by the dynamic IP address server. The dynamic IP address server is generally

referred to as the DHCP server.

Step 1: Click on Windows Logo button on your lower left corner, on your “search programs” or

RUN box (for XP) box type in CMD

Step 2: At the command prompt, type in “ipconfig /all” as shown below

IV. Customize your DVR System – Configure Network Setup

Step 3: The command prompt may look different on your screen, but it display a line “Ethernet

adapter Local Area Connection”. Type ipconfig /all in that window, and then press the

enter key. This will display a lot of network information. If it scrolls off the top you may

need to enlarge the window or use the scroll bar to scroll down and look for “Ethernet

adapter Local Area Connection”.

Step 4: You need to write down some of the information in this window. Take down the IP

address, Subnet Mask, Default Gateway, and DNS Servers. Type exit in this window, then

press the enter key to close it.

Step 5: Assign a network address to DVR.

5.1 On your DVR desktop screen as shown below, click on LAN Setup icon.

IV. Customize your DVR System – Configure Network Setup

LAN Setup

5.2 Double click on the Local Area connection icon

5.3 Click Properties >>>>> highlight Internet Protocol version 4 (TCP/IP), click OK.

5.4 Enter the local network address to be use for the DVR system. Every network is using a

different set of network address range, check with your modem or router as to what range

of network address to use. Usually, Linksys routers have a network address range starting

at 192.168.1.2 >>>> up to 253. If you have Linksys, you may use 192.168.1.200 for your

DVR. Make sure you check with your router, as this is just an assumption. Refer to your

notes from Step 4 to give you an idea what is the range of network address used by your

router.

Use the following IP address

IP address: 192.168.1.200

Subnet Mask: 255.255.255.0

Default Gateway: 192.168.1.1

Use the following DNS server:

Preferred DNS Server: 192.168.1.1

Step 1: From your DVR desktop screen, using your mouse, double click the time clock at the

lower right corner of your desktop screen. To simply change the date and time, click your

mouse on “Change date and time settings….”

Step 2: Click “Change Date and Time….” to change date and time. Click your mouse on the date,

then click your mouse on the hour or minutes to change the time. Use the arrow

up/down on the right side of the time as shown here to change the time. Click “Change

Time Zone” if you need to change your time zone and select the correct zone for your

state, then click OK when finished.

V. Customize DVR System Time Clock

Optiview VR Series Quick start guide

Brand: Optiview

Model: VR Series

Category: Digital Video Recorders (DVR)

Type: Quick start guide

Download PDF

report

Optiview VR Series Quick start guide

Optiview VR Series Quick start guide

Other documents