Philips 32PT8302/37 Quick start guide

Page is loading ...

REMOTE CONTROL BUTTON DESCRIPTIONS

Select (VCR DVD SAT AMPACC) -

Press to set

the TV

this button to cycle across the accessory

mode dial. Stop pressing when the mode you desire

is lighted. The light will stay on for 2 seconds and

then begin blinking to indicate the remote is in your

desired mode. Once the mode is selected, you must

press a button within 60 seconds for the remote to

remain in the selected mode or it will default back to

the TV mode.

SLEEP Button - Press to set the TV to automatically

turn itself OFF at a given amount of time.

AV

(4)

Button - Press repeatedly to select the dif-

ferent signal sources connected to the A/V inputs on

the TV.

SOUND Button - Press to select an AutoSound™

control. Choose from four factory-set controls

(Speech, Music, Movie, and Multimedia) and a PER-

SONAL to tailor the TV sound to enhance the particu-

lar type of program you are watching.

ACTIVE CONTROL

(7)

Button - Press repeatedly

to toggle the Active Control to ON , Display Logo,

Display On, and Off. When ON, the sharpness and

noise reduction will be continuously monitored.

Cursor Buttons (Left, Right, Up, Down) - Press

these buttons to highlight, select, and adjust items on

the TV's onscreen menu. Also, press the left or right

cursor buttons to adjust the picture format.

Menu (Select) Button - Press for the onscreen menu

to appear. Pressing the menu button after menu selec-

tions are made will eliminate the menu from the dis-

play.

Volume (+) or (–) Buttons - Press to adjust the TV

sound level.

Number Buttons - Press the number buttons to select

TV channels. When selecting single-digit channels,

press the number of the desired channel. The TV will

pause for a few seconds and then tune to the selected

channel. (Note: You can press 0, then the number

also.) For channels 100 and above, first press 1 then

the next two numbers of the desired channel.

SMILEY Button - Press to add channels in the

“QuadraSurf” lists. Works with all colored buttons.

Rec(ord)/SAP Button - Press to start the recording of

a videotape. Also, this button activates or deactivates

the SAP feature (if available).

(Virtual Dolby) Button - Press to set various

factory Surround Sound listening modes.

PIC(TURE) SIZE Button - Press to adjust the picture

format.

NOTE: These buttons are dedicated to the PIP feature

within certain models. This TV does not contain these

PIP features, therefore these buttons will have no func-

tionality when pressed.

OK

1

2

3

4

5

6

7

8

0

9

Select

SLEEP

ACTIVE

CONTROL

CC

AV

CLOCK

MENU

EXIT

PICTURE

SOUND

STATUS

SELECT

PIC SIZE

MAIN

FREEZE

QuadraSurf

TM

PROGRAM

LIST

TV/VCR

REC

SAP

A/CH

SATVCR AMP ACCDVD

VOL CH

MUTE

Power

1

Power Button - Press to turn the TV ON and OFF.

CC/

22

Button - Press to select Closed Captioning

options within the menu. Also, press this button to being

playback of a prerecorded video.

;;

(Pause) Button - Press to pause the viewing of a

prerecorded video. The picture will freeze on the screen

until the Play or Pause buttons are pressed again.

Clock/

¢¢

Button - Press the CLOCK button to

access the onscreen Clock menu. Also, press this button

to Fast Forward a prerecorded tape.

Picture Button - Press to select an AutoPicture™ con-

trol. Choose from four factory-set controls (MOVIES,

SPORTS, WEAK SIGNAL, and MULTI MEDIA) and

a PERSONAL control that you set according to your

own preferences through the onscreen PICTURE

menu. The four factory-set controls will tailor the TV

picture so as to enhance the particular type of program

you are watching, or to improve the picture of a pro-

gram that has a weak signal.

OK Button - Press to activate selection when program-

ming remote control.

Status/Exit Button - Press to see the current channel

number on the TV screen. Also press to clear the TV

screen after control adjustments.

Mute Button - Press to turn the TV sound OFF. Press

again to return the sound to its previous level.

Channel (+) or (–) Buttons - Press to change the tuned

channel.

FROWNIE Button - Press to delete channels in the

“QuadraSurf” lists. Works with all colored buttons.

QuadraSurf™ Buttons - (Red, Green, Yellow, Blue)

Allows you to store and surf up to 10 channels you

choose for each colored button.

Program List Button - Press to display a list of chan-

nel numbers and their names. Each channel will appear

as a selectable menu item. The current channel will be

highlighted by default. Only five channels will be

shown onscreen at one time; press the CURSOR UP or

CURSOR DOWN button to scroll the list and highlight

a channel. Press the CURSOR RIGHT button to tune to

the highlighted channel. Channels marked “Skipped” in

the “Channel Edit” control will not appear in the list.

Each channel that is being blocked by AutoLock™ will

appear with a padlock icon to indicate that the channel

is not viewable.

TV/VCR (A/CH) Button - TV/VCR – Press while in

the VCR mode (the VCR indicator on the front of the

VCR will light) to view the playback of a tape. Press

again to place in the TV position (the VCR indicator

light will go off) to view one program while recording

another program. A/CH – Press to toggle between the

currently viewed channel and the previously viewed

channel.

FREEZE Button - Press to freeze the picture on the TV

screen. Press a second time to resume normal viewing.

The signal being received during the time the picture is

frozen will be lost. When the picture is unfrozen, the video

will return to real time broadcast.

REMOTE CONTROL BUTTON DESCRIPTIONS

OK

1

2

3

4

5

6

7

8

0

9

Select

SLEEP

ACTIVE

CONTROL

CC

AV

CLOCK

MENU

EXIT

PICTURE

SOUND

STATUS

SELECT

PIC SIZE

MAIN

FREEZE

QuadraSurf

TM

PROGRAM

LIST

TV/VCR

REC

SAP

A/CH

SATVCR AMP ACCDVD

VOL CH

MUTE

Power

2

BASIC TV AND R

EMOTE CONTROL OPERATION

3

1

Press the POWER button

to turn the TV ON.

Note: You can also press

any button on the front of

the TV to turn the TV ON.

2

Press the VOLUME + but-

ton to increase the sound

level, or the VOLUME –

button to lower the sound

level.

Pressing both buttons at

the same time will display

the on-screen menu. Once in

the menu, use these buttons

to make adjustments or

selections.

3

Press the CHANNEL UP +

or DOWN – button to

select TV channels.

4

Point the remote control

toward the remote sensor

window on the TV when

operating the TV with the

remote.

REMOTE CONTROL

T

o load the supplied batteries

into the remote:

1. Remove the battery com-

partment lid on the back of the

remote.

2. Place the batteries (2-AA)

in the remote. Be sure the (+)

and (-) ends of the batteries line

up correctly (inside of case is

marked.)

3. Reattach the battery lid.

Battery

Compartment

2-AA Batteries

Battery Lid

POWER

3

+

–

VOLUME

+

–

CHANNEL

2

1

Volume and

Channel buttons are

located on the top

of the television

cabinet.

OK

1

2

3

4

5

6

7

8

0

9

Select

S

L

E

P

A

C

T

I

V

E

C

O

N

T

R

O

L

C

A

V

C

L

O

C

K

M

E

N

U

EXIT

P

IC

T

U

R

E

S

O

U

N

D

S

T

A

T

U

S

E

L

E

C

T

P

I

C

S

I

Z

E

M

A

I

N

F

R

E

Z

E

Q

u

a

d

r

a

S

u

r

f

T

M

P

R

O

G

R

A

M

L

I

S

T

TV/VCR

R

E

C

S

A

P

A

/

C

H

SA

T

VCR

AM

P

ACC

DVD

V

O

L

C

H

M

U

TE

Power

Remote Sensor

Window

Audio, Video, S-Video

and Headphone Jacks

located on the side of

the television.

Back of Remote

BASIC ANTENNA AND CABLE

CONNECTIONS

Y

our home’s signal input might come

from a single (75 ohm) round

cable, a Converter Box, or from an

antenna. In either case the connection

to the TV is very easy.

1

If your Cable TV signal or

Antenna signal is a round cable

(75 ohm) then you're ready to

connect to the TV.

If your antenna has flat twin-

lead wire (300 ohm), you first

need to attach the antenna wires

to the screws on a 300 to 75 ohm

adapter.

If you have a Cable Converter

Box: Connect the Cable TV sig-

nal to the Cable Signal IN(put)

plug on the Converter.

2

Connect the Cable TV cable or

Antenna cable (or 300 to 75 ohm

adapter) to the 75Ω plug on the TV.

If you have a Cable Converter

Box: Connect the OUT(put) plug

from the Converter to the 75Ω plug

on the TV.

4

Y

our Cable TV input into your

home may be a single (75 ohm)

cable or use a cable box decoder. In

either case the connection is very

simple. Follow the steps below to

connect your cable signal to your

new television.

This connection will supply Stereo

sound to the TV.

1

Connect the open end of the

round Cable Company supplied

cable to the 75Ω input on the TV.

Screw it down finger tight.

After using the AutoProgram

Control, press the CH + and – but-

tons to scroll through all the channels

stored in the television’s memory.

HELPFUL HINT

Back of TV

Cable signal

coming from

Cable Company

Jack Panel

Back of TV

75 ⍀

1

2

Antenna Connection

300 to 75Ω

Adapter

Combination

VHF/UHF Antenna

(Outdoor or Indoor)

Twin Lead

Wire

Round Cable

75Ω

Back of TV

Direct Cable Connection

75Ω Round

Coaxial Cable

CABLE BOX CONNECTIONS

5

I

f your cable signal uses a cable box

or decoder, follow the easy steps

below to complete the connection.

Cable Box (w/RF In/Outputs):

This connection will be mono.

1

Connect the Cable Company

supplied cable to

the signal

IN(put) plug on the back of the

Cable Box.

2

Using a separate round coaxial

cable, connect one end to the

OUT(put) (TO TV) plug on the

back of the Cable Box.

3

Connect the other end of the

round coaxial cable to the 75Ω

input on the back of the televi-

sion. Screw it down finger tight.

NOTE: If applicable, set the OUT-

PUT CHANNEL SWITCH on the

back of the cable box to CH 3 or 4.

Tune the TV to the same channel and

change channels at the cable box. In

some cases, the cable box will auto-

matically tune to either channel 3 or 4,

change channels until the picture

appears.

Cable Box (w/Audio/Video

Outputs):

This connection will supply Stereo

sound.

4

Connect the Cable Company

supplied cable to

the cable sig-

nal IN(put) plug on the back of

the Cable Box.

5

Using a RCA type Video Cable,

connect one end of the cable to

the Video (or ANT, your cable

box may be labeled differently)

Out jack on the cable box and

the other end to the AV1 Video

Input on the TV.

6

Connect one end of the Audio

Left and Right Cable to the left

and right Audio Out L & R

jacks on the cable box. Connect

the other end to the AV1 Audio L

& R Input jacks on the TV.

NOTE: Press the AV button or use the

CH+ or CH- on the TV remote control

to tune to the AV1 channel for the

cable box signal. Once tuned, change

channels at the cable box, not the tele-

vision.

Cable Box (w/RF In/Outputs):

TO

TV/VCR

CABLE

IN

IR

USB

DVD-D OUT

AUDIO IN

SPDIF

VIDEO

IN OUT

S-VIDEO

R L

AUDIO OUT

TV

PASSCARD

Y Pb Pr

OPTICAL

SPDIF

24

TO

TV/VCR

CABLE

IN

IR

USB

DVD-D OUT

AUDIO IN

SPDIF

VIDEO

IN OUT

S-VIDEO

R L

AUDIO OUT

TV

PASSCARD

Y Pb Pr

OPTICAL

SPDIF

Jack Panel Back of Cable Box

Cable Signal IN from the

Cable Company

Round 75Ω

Coaxial Cable

Jack Panel Back of TV

Cable Signal IN

from the Cable

Company

Cable Box with

A/V Outputs

Jack Panel

Back of TV

Audio Cables

L (White) & R (Red)

Video Cable

(Yellow)

Cable Box (w/Audio/Video Outputs):

AV1 (AUDIO

/VIDEO) AND AV2 INPUT CONNECTION

6

Select

SLEEP

ACTIVE

CONTROL

CC

AV

CLOCK

PICTURE

SOUND

4

SATVCR AMP ACCDVD

POWER

8

7

3

4

Audio In

(Red and

White)

VCR Two

(or accessory device)

(Equipped with Video

and Audio Output

Jacks)

Video In

(Yellow)

Back of VCR

Back of TV

AV 1

Connection

AV2 Connection

VCR One (or accessory device)

(Equipped with Audio and

Video Output Jacks)

T

he TV’s audio/video input jacks

are for direct picture and sound

connections between the TV and a

VCR (or similar device) that has

audio/video output jacks. Both the

AV1 and AV2 Input Jack connections

are shown on this page, but either

one can be connected alone. Follow

the easy steps below to connect your

accessory device to the AV1 and AV2

IN Jacks located on the back of the

TV.

1

Connect the VIDEO (yellow)

cable to the VIDEO AV 1 IN (or

AV2 IN) jack on the back of the

TV.

2

Connect the AUDIO (red and

white) cables to the AUDIO (left

and right) AV 1 IN (or AV2 in)

jacks on the rear of the TV.

3

Connect the VIDEO (yellow)

cable to the VIDEO OUT jack on

the back of the VCR (either one

or two) or accessory device being

used.

4

Connect the AUDIO (red and

white) cables to the AUDIO (left

and right) OUT jacks on the rear

of the VCR (either one or two) or

accessory device being used.

5

Turn the VCR (either one or

two) or accessory device and

the TV ON.

6

Press the AV button or the CH+

or CH- buttons to set the TV to its

AV 1 or AV2 channel.

7

With either of the VCRs (or

accessory devices) ON and a pre-

recorded tape (CD, DVD, etc.)

inserted, press the PLAY button

to view the tape on the television.

Audio and video cables are not sup-

plied with the TV, but are available

from Philips or electronics retailers.

HELPFUL HINT

S-VIDEO (S-VHS) INPUT CONNECTIONS

T

he S(uper)-Video connection on

the rear of the TV can provide

you with better picture detail and

clarity for the playback of accessory

sources such as DBS (digital broad-

cast satellite), DVD (digital video

discs), video games, and S-VHS VCR

(video cassette recorder) tapes than

the normal antenna picture connec-

tions.

NOTE: The accessory device must

have an S-VIDEO OUT(put) jack in

order for you to complete the connec-

tion on this page.

1

Connect one end of the S-

VIDEO CABLE to the S-

VIDEO jack on the back of the

TV. Then connect one end the

AUDIO (red and white)

CABLES to the AV1 in AUDIO

L and R (left and right) jacks on

the rear of the TV.

2

Connect other end of the S-

VIDEO CABLE to the S-VHS

(S-Video) OUT jack on the back

of the VCR. Then connect the

other ends of the AUDIO (red

and white) CABLES to the

AUDIO (left and right) OUT

jacks on the rear of the VCR.

3

Turn the VCR and the TV

ON.

4

Press the AV button or the

CH + or CH – buttons on the

remote to scroll the channels

until AV2 appears in the upper

left corner of the TV screen.

5

Now your ready to place a pre-

recorded video tape in the VCR

and press the PLAY  button

.

7

OK

1

2

3

H

Select

SLEEP

ACTIVE

CONTROL

CC

AV

CLOCK

MENU

EXIT

PICTURE

SOUND

STATUS

SELECT

4

SATVCR AMP ACCDVD

VOL CH

MUTE

OK

1

2

3

H

Select

SLEEP

ACTIVE

CONTROL

CC

AV

CLOCK

MENU

EXIT

PICTURE

SOUND

STATUS

SELECT

4

SATVCR AMP ACCDVD

VOL CH

MUTE

POWER

8

7

3

4

AV2

VCR or External

Accessory Device

(with S-Video Output)

Audio Cables

(Red &

White)

S-Video

Cable

Back of TV

COMPONENT VIDEO

(CVI) INPUT CONNECTIONS

C

omponent Video inputs provide

for the highest possible color

and picture resolution in the play-

back of digital signal source materi-

al, such as with DVD players. The

color difference signals (Pb, Pr) and

the luminance (Y) signal are con-

nected and received separately,

which allows for improved color

bandwidth information (not possible

when using composite video or S-

Video connections).

1

Connect the Component (Y,

Pb, Pr) Video OUT jacks from

the DVD player (or similar

device) to the (Y, Pb, Pr) in(put)

jack on the TV. When using the

Component Video Inputs, it is

best not to connect a signal to the

AV in Video Jack.

2

Connect the red and white

AUDIO CABLES to the Audio

(left and right) output jacks on

the rear of the accessory device

to the Audio (L and R) AV1 in

Input Jacks on the TV.

3

Turn the TV and the DVD (or

digital accessory device) ON.

4

Press the AV button or the

CH + or CH – buttons to

scroll the available channels

until CVI appears in the upper

left corner of the TV screen.

5

Insert a DVD disc into the

DVD player and press the

PLAY  button on the DVD

Player.

The description for the component video

connectors may differ depending on the

DVD player or accessory digital source

equipment used (for example, Y, Pb, Pr; Y,

B-Y, R-Y; Y, Cr, Cb). Although abbrevia-

tions and terms may vary, the letters b and r

stand for the blue and red color component

signal connectors, and Y indicates the lumi-

nance signal. Refer to your DVD or digital

accessory owner’s manual for definitions and

connection details.

HELPFUL HINT

8

OK

1

2

3

4

5

6

H

Select

SLEEP

ACTIVE

CONTROL

CC

AV

CLOCK

MENU

EXIT

PICTURE

SOUND

STATUS

SELECT

4

SATVCR AMP ACCDVD

VOL CH

MUTE

POWER

8

7

3

4

Component

Video Cables

(Green, Blue,

Red)

Audio

Cables

(Red &

White)

Accessory Device

Equipped with

Component Video

Outputs

Back of TV

The CVI connection will be dominate over the AV1

in Video Input. When a Component Video Device is

connected as described, it is best not to have a video

signal connected to the AV1 in Video Input jack.

AV (AUDIO

/VIDEO) 4 INPUT CONNECTION

9

T

he AV4 Input Jacks provide

Component Video Inputs for

accessories like Digital Video

Players.

Connecting a Digital device using

the COMPONENT VIDEO

Inputs:

1

Connect the Component (Y,

Pb, Pr) Video OUT jacks from

the DVD player (or similar

device) to the (Y, Pb, Pr) AV4

in(put) jacks on the TV.

2

Connect the red and white

AUDIO CABLES to the

Audio (left and right) output

jacks on the rear of the acces-

sory device to the Audio (L and

R) AV4 in(put) jacks on the TV.

3

Turn the TV and the DVD

(or digital accessory device)

ON.

4

Press the AV button on the

remote to tune to the AV4

channel.

5

Press the PLAY button on the

DVD (or digital accessory

device) to view the program on

the television.

S-VIDEO

OUT

L

R

AUDIO

VIDEO

COMP VIDEO

Y

Pb

Pr

AV4

1

3

5

OK

1

2

3

4

5

6

7

8

0

9

H

Select

SLEEP

ACTIVE

CONTROL

CCAV

CLOCK

MENU

EXIT

PICTURE

SOUND

STATUS

SELECT

4

QuadraSurf

TM

PROGRAM

LIST

TV/VCR

REC

SAP

A/CH

PIP

SATVCR AMP ACCDVD

VOL CH

MUTE

4

2

Back of TV

Accessory Device

Equipped with

Component Video

Outputs

Component

Video Cables

(Green, Red,

Blue)

Audio

Cables

(red &

white)

MONITOR OUT(

PUT) CONNECTIONS

10

T

he Audio/Video (Monitor) Output

jacks are great for recording with

a VCR or used to connect an exter-

nal audio system for better sound

reproduction.

AUDIO SYSTEM

CONNECTION:

1

Connect one end of the

R(ight) and L(eft) AUDIO

(Monitor Out) jacks on the TV

to the R and L audio input jacks

on your amplifier or sound sys-

tem. Set the audio system’s vol-

ume to a normal listening level.

2

Turn the TV and audio sys-

tem ON. To adjust the volume

on the audio system, you will

need to change the volume at

the external audio system, not

the television.

SECOND VCR CONNECTION:

NOTE: Refer to panel number 6 for

the proper hookup of the first VCR.

Follow the instructions on how to

tune to the AV1 channel to view a

pre-recorded tape.

The following steps allow you to

connect a second VCR to record

the program while your watching

it.

3

Connect one end of the yellow

Video Cable to the Monitor

Out VIDEO plug. Connect the

Philips 32PT8302/37 Quick start guide

This manual is also suitable for

Philips 32PT8302/37 Quick start guide

in other languages

Related papers

Other documents