MyBinding RSL-2701 User manual

Royal Sovereign RSL-2701

27 Inch Table Top School

Roll Laminator

Instruction Manual

TABLE TOP LAMINATOR

RSL-2701 OWNER’S MANUAL

Please read instructions carefully before use.

2

TABLE OF CONTENTS

▣Introduction ----------------------------------------------------------------------------------- 3

▣Package Contents --------------------------------------------------------------------------- 3

▣Safety Precautions --------------------------------------------------------------------------- 4

▣Parts -------------------------------------------------------------------------------------------- 5

▣Features Guide ------------------------------------------------------------------------------- 6

▣Operating Instructions -------------------------------------------------------------------- 8

▣Film Loading and Threading ------------------------------------------------------------ 8

▣Maintenance --------------------------------------------------------------------------------- 11

▣Trouble shooting guide ------------------------------------------------------------------- 12

▣Specifications ------------------------------------------------------------------------------- 13

▣Warranty ----------------------------------------------------------------------------------- 14

3

INTRODUCTION

Thank you for purchasing RSL-2701 Table Top Laminator. It has been

designed and manufactured to provide years of continuous service. For

high quality lamination, please read this instruction manual thoroughly.

This manual will provide you with complete operating and maintenance

information.

PACKAGE CONTENTS

Owner's

Manual

RSL-2701

Preloaded Roll Films

(635mm x 75mic x 30m)

(

25in x 3mil x 98.4ft

)

SPARE FUSE

(250V / 15A)

4

SAFETY PRECAUTIONS

WARNING

Failure to comply with any of the following safety procedures could result in serious

injury.

1. Insure the unit is plugged into a properly grounded outlet with the correct voltage.

2. Only licenses electricians should service or repair the electrical wiring.

3. Keep flammable and wet objects away from the machine.

4. Place machine on a level sturdy surface.

5. Avoid excessive sunlight, humidity and temperatures.

6. Unplug the machine when moving it or when it's not in use.

7. Keep out of reach of children.

8. Only authorized maintenance and service technician are permitted to make repairs.

9. Do not cover the surface of the machine until the machine is completely cooled.

10. When cleaning the machine, don't use flammable sprays or materials.

11. Do not touch the rollers or allow foreign objects inside the machine.

5

PARTS

1- Upper Film

2- Lower Film

3- Idle Bar

4- Hot Rollers

5- Feed Table

6- Paper Guide

7- Control Panel

8- Tension Knob

9- Power Switch

③

①

④

②

⑤

⑥

⑦

⑧

⑨

6

FEATURES GUIDE

Figure 1

Run and stop the machine

Reverse the rollers to undo jams

and co

r

rect misfed documents

Reduce roller speed

(

1~10 s

p

eed settin

g

s

)

Increase roller speed

(

1~10 s

p

eed settin

g

s

)

Film Application Temperature

210° F~230° F

Film Application Temperature

230° F~270° F

Film Application Temperature

270° F~310° F

230° F~270° F

210° F~230° F

7

FPower Switch (1) - Located on the rear of

the machine. “I” (on) “0” (off). (Fig. 2)

Cross Cutter (2) - Used to cut off the

laminated web. (Fig. 2)

Figure 2

Feed Guide (3) –The feed guide permits

alignment of the item(s) to be laminated. To

position the adjustable guide, loosen the knob,

slide it to the desired position and tighten the

knob to secure the feed guide in place. (Fig.3)

Safety Shield (4) – It prevents entanglement

NOTE: If the safety shield is opened, the power

to the motor will turn off.

Figure 3

Film Shaft and Locking

Core Adapter (5) –

The film shaft holds the film supply on the

machine. The locking core holds and locks the

film on the shaft to prevent shifting. (Fig.4)

Figure 4

Film Tension Adjustment (6) – Allows the

operator to increase or decrease film web

tension. To increase the tension turn the knob

clockwise and to decrease tension turn the

knob counterclockwise. (Fig. 5)

Figure 5

①

②

③

④

8

Idler bar

OPERATING INSTRUCTION

1. Turn the laminator ON (I) located on the rear of the machine. (Fig. 2)

2. Choose appropriate laminating thickness and speed. (Fig. 1)

3. Do not begin laminating until the blinking light is steady (approximately 10 minutes).

4. Position the item to be laminated on the feed table.

5. Press the RUN button. The rollers will begin to turn, wait for heat line to disappear,

feed the item into the machine.

6. Stop the laminator when all of the items have completely exited the rear of the

machine.

Repeat the above steps until all of your lamination is completed. When lamination is

completed the machine is not in use for an extended period of time turn the power off.

NOTE: Stand by mode and auto power off mode

- Stand by mode: If no activity is made within 30 minutes after each use the

machine will automatically switch into stand by mode. (In stand-by mode the

temperature will decrease to 80~90℃ (176~194°F) and the three film thickness

setting indicators will blink).

- Auto power off mode: If the machine is in stand by mode and no activity is

made for 60 minutes the machine will automatically power off.

- If any activity is made while in stand by or auto power off mode the machine

will return to it’s previous stage.

FILM LOADING & THREADING

Figure 6

Upper

roll film

Lower

roll film

Roller

Idler bar

Laminating

direction

9

▲ LOADING UPPER ROLL FILM

1. Slightly slide the shaft to the right and

pull it out from the machine.

Figure 7

2. Take both lock core adapters off from the

shaft.

Figure 8

3. Insert one of the core adapters into the

right end of the film core. For film with

poly-in (adhesive side is inside the web),

make sure the adhesive side is facing

upward. (Fig. 9)

Figure 9

10

4. Insert the film shaft into the roll of film

from the right side with the copper end last.

Align and insert the core adapter on the left

end of the film core.

Figure 10

5. Center the film on the shaft and lock it in

place with the locking core adapters

Figure 11

6. Carefully return the film shaft back into

place.

Figure 12

11

▲ LOADING LOWER ROLL FILM

1. Repeat steps 1-5 to load lower roll film.

2. Once the upper and lower film is on the shaft, pull the film from the top roll down to

the bottom roll to make certain that the film is aligned properly. Then tighten the

lower locking core screws.

NOTE: If the film is not aligned properly exposed adhesive will adhere to the rollers

and may cause the film to jam.

▲ FILM THREADING

Refer to Figure 6

MAINTENANCE

1. Do not apply any cleaning fluids to the rollers certain fluids may cause damage.

2. Do not clean rollers with sharp or pointed objects.

3. Use adhesive remover to clean resin off of the rollers.

4. Use a damp cloth with water to clean the body of the machine.

5. Store machine in a dry clean area.

12

TROUBLE SHOOTING GUIDE

Problem Cause Remedy

Rollers do not operate

after the RUN/STOP

Button is pressed

1. Safety cover is opened.

2. Power cord is not

plugged in

3. Machine is not turned

on.

1. Check safety cover is

properly closed.

2. Plug in the power

cord.

3. Turn the machine on.

Roller is not heating Call your authorized dealer Call your authorized dealer

Poor Lamination

1. Unbalanced film

tension.

2. Lower idler bar is not

properly positioned

3. Wrong

temperature/speed

setting

1.Adjust film tension

2. Push idler bar in proper

position

3. Follow manufacturers

recommended

temperature and speed.

13

SPECIFICATIONS

MODEL RSL-2701

Power supply AC 120V / 60Hz

Power consumption 1450W

Max laminating width 685(mm) / 27(in)

Film thickness 25~125(mic) / 1~5(mil)

Max laminating speed 2.4(m/min) / 7.9(ft/min)

Ready time 10 min

Heating method Hot Roller

Driving motor DC geared motor

Temperature control Digital(micom)

Speed control Digital(10steps)

Transport type 4 Roller

Cooling system no

Side cutter no

Cross cutter yes

Film alignment no

Hot lamination yes

Cold lamination no

Reverse yes

Remote control no

Foot switch no

Dimensions(w x d x h) 920 x 520 x 320(mm) / 36.2 x 20.5 x 12.6(in)

Unit weight 50 (kg) / 110.2 (lbs)

14

WARRANTY

Royal Sovereign International warrants the equipment sold is free from defects in material and

workmanship for a period of One (1) year for Parts and Labor from the date of installation,

excluding lamination rollers which are warranted for Six (6) months. This warranty is extended only

to the original purchaser. This warranty is the only warranty made by Royal Sovereign International

and cannot be modified or amended. Royal Sovereign’s sole and exclusive liability and the

customer’s sole and exclusive remedy under this warranty shall be, at Royal Sovereign’s option, to

repair or replace any such defective part or product. These remedies are only available if Royal

Sovereign’s examination of the product discloses to Royal Sovereign’s satisfaction that such defects

actually exist and were not caused by misuse, neglect, attempt to repair, unauthorized alternation or

modification, incorrect line voltage, fire, accident, flood or other hazard.All warranty claims must be

filed through the authorized Royal Sovereign dealer or reseller through which the equipment was

originally purchased. Model, serial number and date of delivery are required for all claims.

The warranty made herein is in lieu of all other warranties, expressed or implied, including any

warranty or merchantability or fitness for a particular purpose. Royal Sovereign will not be liable for

personal damage or personal injury (unless primarily caused by its negligence), loss of profit, or

other incidental or consequential damages arising out of the use or inability to use this equipment.

LIMITED WARRANTY

This warranty specifically does not cover damage to laminating rollers caused by knives, razor

blades, or any sharp objects or abrasives, or failure caused by adhesives, or damage caused by lifting,

tilting or improper use of the machine. Warranty repair or replacement by Royal Sovereign or its

authorized Reseller(s) does not extend the warranty beyond the initial one year period from the date

of installation. Unauthorized customer alterations will void this warranty.

RS Holland B.V.

Planetenweg 75 2132HM Hoofddorp, The Netherlands.

TEL : +31) 23-5626620, +31) 23-5654451

FAX : +31) 23-5654565

E-mail : purchaseorder@royalsovereign.com

Royal Sovereign Inc. <Oversea Sales Office>

1001, World Meridian II, 426-5, Gasan-dong,

Geumcheon-gu, Seoul, 153-759, KOREA

TEL : +82)2-2025-8800 FAX : +82)2-2025-8830

E-mail : [email protected]m

RS Canada Inc.

164 Oakdale Road, Toronto, Ontario M3N 2S5

CANADA

TEL : +1) 416-741-8400 FAX : +1) 416-741-8185

E-mail : [email protected]m

RS International Australia PTY. LTD.

30 Prime Drive, Seven Hills, NSW 2147, Australia

TEL : +61) 2-9674-2127

FAX : +61) 2-9674-2027

E-mail : [email protected]m

CORPORATE HEADQUARTERS

Royal Sovereign International Inc.

2 Volvo Drive, Rockleigh, NJ 07647 U.S.A.

TEL : +1) 800-397-1025 FAX : +1) 201-750-1022

E-mail : [email protected]m

MyBinding RSL-2701 User manual

This manual is also suitable for

MyBinding RSL-2701 User manual

Related papers

Other documents