Gamewell FCI IF658 Installation & Operation Manual

Brand: Gamewell FCI

Model: IF658

Category: Networking

Type: Installation & Operation Manual

This manual is also suitable for

12 Clintonville Road, Northford, CT 06472, 203-484-7161, FAX 203-484-7118

www.gamewell-fci.com

FocalPoint™ S ystem Utilities User’s Guid e —

FocalPoint™ Gateway

Installation & Operation Manual

Published in U.S.A.

P/N: 52649 B3

ECN: 10-030

2 FocalPoint™ Gateway Installation & Operation Manual - P/N: 52649:Rev: B3 2/11/10

IMPORTANT INFORMATION

This manual is designed for use by factory trained installers

and operators of the Gamewell/FCI FocalPoint™ System.

All illustrations, functional descriptions, operating and

installation procedures, and other relevant information are

contained in this manual.

The contents of this manual are important, and the manual

must be kept with the system at all times. If building

ownership is changed, this manual, including any testing

and maintenance information, must be passed along to the

new owner(s).

Manuals and instructions for other devices forming part of

the FocalPoint™ System should be kept together.

Purchasers who install this system for use by others must

leave the instructions with the user. A copy of these

instructions is included with each product and is available

from the manufacturer.

This equipment is Listed by various listing agencies for use

in emergency evacuation and fire alarm systems. Use only

components that are compatible with this FocalPoint™

System. The installation MUST be in accordance with the

instructions in this manual.

Therefore:

• DO NOT deviate from the procedures described in this

manual.

• DO NOT assume any details not shown in this manual.

• DO NOT modify any electrical or mechanical features.

• DO comply with all codes and standards set forth by

the Authority Having Jurisdiction.

The term “Authority Having Jurisdiction” has become a

standard term in the fire alarm industry. An acceptable

definition of “Authority Having Jurisdiction” is:

Fire alarm systems installed in the USA fall under the

jurisdiction of some authority. In some areas, this may be a

local fire department; in other areas, it may be a building

inspector, insurance firm, etc. Different authorities may

have their own local requirements for the way the fire alarm

system is installed and used. Most local authorities based

their requirements on the NFPA (National Fire Protection

Association) codes, but there may be important

differences. You must install this system in the way in

which the Authority Having Jurisdiction requires. If you do

not know which authority has jurisdiction in your area,

contact your local fire department or building inspector for

guidance.

It is important that you tell users to be aware of any

requirements defined by the Authority Having Jurisdiction.

The installation MUST be in accordance with the following

standards:

• National Fire Alarm Code (NFPA 72)

• National Electrical Code (NFPA 70)

• Life Safety Code (NFPA 101)

WARNING: Touching components, which are

improperly installed, applied or operated, could be

hazardous and possibly fatal. Short circuits could

cause arcing that could result in molten metal injuries.

Therefore, only qualified technicians familiar with

electrical hazards should perform checkout

procedures. Safety glasses should be worn, and test

equipment used for voltage measurements should be

designed for this purpose and be in good working

order.

ENVIRONMENTAL CONSIDERATIONS

It is important that this equipment be operated within its

specifications: Recommended operating temperature

range: 0°C to 49°C (32°F to 120°F) and at a relative

humidity 93% ± 2% RH (non-condensing) at 32°C ± 2°C

(90°F ± 3°F).

INSTALLATION CONSIDERATIONS

Check that you have all the equipment you need to

complete the installation. Follow the field wiring diagrams

and installation notes in this manual.

Install the equipment in a clean, dry environment (minimal

dust). Avoid installing the equipment where vibrations will

occur.

Remove all electronic assemblies prior to drilling, filing,

reaming, or punching the enclosure. When possible, make

all cable entries from the side, being careful to separate the

power-limited conductors from the non power-limited

conductors. Before making modifications, verify that they

will not interfere with battery, transformer, and printed circuit

board location.

Do not over tighten screw terminals. Over tightening may

damage threads, resulting in reduced terminal contact

pressure and difficulty with screw terminal removal.

Disconnect all sources of power before servicing, removing,

or inserting any circuit board. Control unit and associated

equipment may be damaged by removing and/or inserting

cards, subassemblies, or interconnecting cables while the

unit is energized.

FocalPoint is a trademark of Honeywell International.

3FocalPoint™ Gateway Installation & Operation Manual - P/N: 52649:Rev: B3 2/11/10

WIRING CONSIDERATIONS

A Gamewell/FCI fire alarm control panel contains power-

limited circuits. You cannot connect external sources of

power to these circuits without invalidating their approval.

Verify that wiring sizes are adequate for all initiating device

and notification appliance circuits. Most devices cannot

tolerate more than a 10% drop from the specified voltage.

The installer must ensure that the wiring and devices

installed in the system meet the current National Electrical

Code, NFPA 70, and all applicable state and local building

code requirements.

Use the conductor size and type required by local codes

(see NFPA 70, Article 760). Wiring resistance must not be

more than that shown on the field wiring diagrams.

To reduce errors and help in servicing the system, all

conductors should be labeled or otherwise coded and

logged at installation to identify circuit assignment and

polarity. If the conductors are logged with a code, keep the

log that explains the code with the manual, so that it is

available to other people working on the panel.

Like all solid state electronic devices, this system may

operate erratically or be damaged when subjected to

lightning induced transients. Although no system is

completely immune to lightning transients and interference,

proper grounding will reduce susceptibility. Gamewell/FCI

does not recommend the use of overhead or outside aerial

wiring due to the increased susceptibility to nearby lightning

strikes. Consult with the Gamewell/FCI Technical Support

Department if any problems are anticipated or encountered.

To prevent the spread of fire, use proper patching materials

to areas where system wiring passes through fire-rated

walls or floors.

SURVIVABILITY

Per the National Fire Alarm Code, NFPA 72, all circuits

necessary for the operation of the notification appliances

shall be protected until they enter the evacuation signaling

zone that they serve. Any of the following methods shall be

considered acceptable as meeting these requirements:

• A two-hour rated cable or cable system.

• A two-hour rated enclosure.

• Performance alternatives approved by Authority

Having Jurisdiction.

MAINTENANCE

To keep your fire alarm system in excellent working order,

ongoing maintenance is required per the manufacturer’s

recommendations and UL and NFPA Standards, and

applicable state and local codes. At a minimum, the

requirements of Chapter 7 of NFPA, the National Fire Alarm

Code, shall be followed. A preventative maintenance

agreement should be arranged through the manufacturer’s

local representative. Though smoke detectors are

designed for long life, they may fail at any time. Any smoke

detector, fire alarm system, or any component of that

system shall be repaired or replaced immediately.

SYSTEM RE-ACCEPTANCE TEST

To ensure proper system operation, this product must be

tested in accordance with NFPA 72, Chapter 7. Re-

acceptance testing is required after any modification, repair,

or adjustment to system hardware, wiring, or programming.

All components, circuits, or system operations known to be

affected by a change must be 100% tested. In addition, to

ensure that other operations are not inadvertently affected,

at least 10% of initiating devices that are not directly

affected by the change, up to a maximum of 50 devices,

must also be tested and proper system operation verified.

Equipment used in the system may not be technically

compatible with the control panel. It is essential to use only

equipment Listed for service with the control panel.

OTHER CONSIDERATIONS

The equipment was tested according to EC directive

89/336/EEC for Class A equipment and was verified to the

limits and methods of EN 55022. FCC WARNING: This

equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with this instruction manual, may cause

interference to radio communications. It has been tested

and found to comply with the limits for Class A computing

devices pursuant to Subpart B of Part 15 of FCC Rules,

which is designed to provide reasonable protection against

such interference when operated in a commercial

environment. Operation of this equipment in a residential

area is likely to cause interference, in which case the user

will be required to correct the interference at his own

expense.

Canadian Requirements: This digital apparatus does not

exceed the Class A limits for radiation noise emissions from

digital apparatus set out in the Radio Interference Regulations of

the Canadian Department of Communications. This Class A

digital apparatus complies with Canadian ICES-003.

Le present appareil numerique n'emet pas de bruits

radioelectriques depassant les limites applicables aux appareils

numeriques de la classe A prescrites dans le Reglement sur le

brouillage radioelectrique edicte par le ministere des

Communications du Canada. Cet appareil numerique de la

classe A est conforme a la norme NMB-003 du Canada.

If these instructions are not clear, or if additional information

or clarification is needed, please consult your local

authorized Gamewell/FCI distributor.

Because of design changes and product improvements, the

information in this manual will be subject to change without

notice. Gamewell/FCI reserves the right to change

hardware and/or software design, which may subsequently

affect the contents of this manual. Gamewell/FCI assumes

no responsibility for any errors that may appear in this

manual.

Neither this manual nor any part of it may be reproduced

without the advance written permission of Gamewell/FCI.

4 FocalPoint™ Gateway Installation & Operation Manual - P/N: 52649:Rev: B3 2/11/10

LIMITATIONS OF FIRE ALARM SYSTEMS

Gamewell/FCI recommends that smoke and/or heat

detectors be located throughout the protected premises

following the recommendations of the current edition of the

National Fire Protection Association Standard 72, the

National Fire Alarm Code (NFPA 72), manufacturer’s

recommendations, State and local codes, and the

recommendations contained in the Guide for the Proper

Use of System Smoke Detectors, which is made available

at no charge to all installing dealers. A study by the Federal

Emergency Management Agency (an agency of the United

States government) indicated that smoke detectors may not

go into alarm or give early warning in as many as 35% of all

fires. While fire alarm systems are designed to provide

warning against fire, they do not guarantee warning or

protection against fire. Any alarm system is subject to

compromise or failure to warn for a variety of reasons. For

example:

Particles of combustion or “smoke” from a developing fire

may not reach the sensing chambers of a smoke detector

because:

• Barriers such as closed or partially closed doors, walls,

or chimneys may inhibit air flow.

• Smoke particles may become “cold” and stratify, and

may not reach the ceiling or upper walls where

detectors are located.

• Smoke particles may be blown away from detectors by

air outlets.

• Smoke particles may be drawn into air returns before

reaching the detector.

In general, smoke detectors on one level of a structure

cannot be expected to sense fires developing on another

level.

The amount of “smoke” present may be insufficient to alarm

smoke detectors. Smoke detectors are designed to alarm

at various levels of smoke density. If such density levels

are not created by a developing fire at the location of

detectors, the detectors will not go into alarm.

Smoke detectors, even when working properly, have

sensing limitations. Detectors that have photo-electronic

sensing chambers tend to detect smoldering fires earlier

than flaming fires, which have little visible smoke.

Detectors that have ionization-type sensing chambers tend

to detect fast flaming fires earlier than smoldering fires.

Because fires develop in different ways and are often

unpredictable in their growth, neither type of detector is

necessarily best and a given type of detector may not

provide adequate warning of a fire.

Smoke detectors are subject to unwanted or nuisance

alarms. For example, a smoke detector located in or near a

kitchen may go into nuisance alarm during normal

operation of kitchen appliances. In addition, dusty or

steamy environments may cause a smoke detector to alarm

unnecessarily. If the location of a smoke detector causes

an abundance of unwanted or nuisance alarms, do not

disconnect the smoke detector; call a professional to

analyze the situation and recommend a solution.

Smoke detectors cannot be expected to provide adequate

warning of a fire caused by arson, children playing with

matches (especially in bedrooms), smoking in bed, violent

explosions (caused by escaping gas, improper storage of

flammable materials, etc.).

Heat detectors do not sense particles of combustion and

are designed to alarm only when heat on their sensors

increase at a predetermined rate or reaches a

predetermined level. Heat detectors are designed to

protect property, not life.

Warning devices (including horns, sirens, bells, and

speakers) may not alert people or awaken sleepers who

are located on the other side of closed or partially open

doors. A warning device that activates on a different floor

or level of a dwelling or structure is less likely to awaken or

alert people. Even persons who are awake may not notice

the warning if the alarm is muffled by noise from a stereo,

radio, air conditioner or other appliance, or by passing

traffic. Audible warning devices may not alert the hearing-

impaired (strobes or other devices should be provided to

warn these people). Any warning device may fail to alert

people with a disability, deep sleepers, people who have

recently used alcohol or drugs, or people on medication or

sleeping pills.

Please note that:

• Strobes can, under certain circumstances, cause

seizures in people with conditions such as epilepsy.

• Studies have shown that certain people, even when

they hear a fire alarm signal, do not respond or

comprehend the meaning of the signal. It is the

property owner’s responsibility to conduct fire drills and

other training exercises to make people aware of the

fire alarm signals and instruct on the proper reaction to

alarm signals.

• In rare instances, the sounding of a warning device

can cause temporary or permanent hearing loss.

Telephone lines needed to transmit alarm signals from a

premise to a central station may be out of service or

temporarily out of service. For added protection against

telephone line failure, backup radio transmission systems

are recommended.

System components, though designed to last many years,

can fail at any time. As a precautionary measure, it is

recommended that smoke detectors be checked,

maintained, and replaced per manufacturer’s

recommendations.

System components will not work without electrical power.

If system batteries are not serviced or replaced regularly,

they may not provide adequate standby when AC power

fails.

Environments with high air velocity or that are dusty or dirty

require more frequent maintenance.

In general, fire alarm systems and devices will not work

without power and will not function properly unless they are

maintained and tested regularly.

While installing a fire alarm system may make the owner

eligible for a lower insurance rate, a fire alarm system is not

a substitute for insurance. Property owners should

continue to act prudently in protecting the premises and the

people on the premises and should properly insure life and

property and buy sufficient amounts of liability insurance to

meet their needs.

5FocalPoint™ Gateway Installation & Operation Manual - P/N: 52649:Rev: B3 2/11/10

Table of Contents

Section 1 FPT Gateway Overview ........................................................................................... 7

1.1: Product Description .......................................................................................................................................7

Table 1.1 FPT Gateway Compatibility...................................................................................................7

Figure 1.1 Basic FPT Gateway Network - Gamewell/FCI.....................................................................7

Figure 1.2 Advanced FPT Gateway Network - FCI...............................................................................8

1.1.1: About Workstation Ethernet Network Installations ............................................................................8

1.2: Agency Listings .............................................................................................................................................9

1.2.1: Compliance..........................................................................................................................................9

1.2.2: Installation ...........................................................................................................................................9

1.2.3: Retrofit Applications .........................................................................................................................10

1.2.4: Environmental Requirements ............................................................................................................10

1.3: Related Documentation ...............................................................................................................................11

Section 2 FPT Gateway Installation ...................................................................................... 13

2.1: Required Equipment ....................................................................................................................................13

2.2: Installation Overview...................................................................................................................................13

2.2.1: Gateway Board Layout......................................................................................................................14

Figure 2.1 FPT Gateway PC Board Layout..........................................................................................14

2.3: Cabinet Installation......................................................................................................................................15

Figure 2.2 Gateway Cabinet Mounting ................................................................................................15

2.4: Hardware Installation...................................................................................................................................16

Figure 2.3 Gateway Parts Mounting - 1 ...............................................................................................16

Figure 2.4 Gateway Parts Mounting - 2 ...............................................................................................17

2.5: Cable Connections .......................................................................................................................................18

Figure 2.5 Gateway Cable Connections ...............................................................................................19

2.5.1: 600 Series Router Serial Data Connection ........................................................................................19

Figure 2.6 600 Series Router Serial Cable Connection........................................................................19

2.5.2: 600 Series Panel Serial Data Connections.........................................................................................19

Figure 2.7 Direct Serial Data Connection Using the IF602 Supplied Cable........................................19

Figure 2.8 Direct Serial Data Connection Using the Gateway Supplied Cable ...................................20

2.5.3: FCI Panel Serial Data Connections ...................................................................................................20

Figure 2.9 E3 Serial Cable Connection ................................................................................................20

Figure 2.10 7100/7200 Serial Cable Assembly/Connection ................................................................20

2.6: Power Connection........................................................................................................................................21

Table 2.1 Power Supply Specifications................................................................................................21

Figure 2.11 Gateway Power Connection..............................................................................................21

2.6.1: Wiring Restrictions............................................................................................................................22

Section 3 FPT Gateway Configuration.................................................................................. 23

3.1: Default FPT Gateway Selection Procedure .................................................................................................23

3.2: FPT Gateway Configuration Procedure.......................................................................................................24

3.2.1: IP Address Setting .............................................................................................................................24

Figure 3.1 Gateway Node Selection.....................................................................................................24

Figure 3.2 Gateway Login Window .....................................................................................................24

Figure 3.3 Gateway IP Configuration ..................................................................................................25

3.2.2: Panel Configuration Settings.............................................................................................................26

3.2.3: Time Settings.....................................................................................................................................27

Figure 3.4 Gateway Time Settings .......................................................................................................27

Figure 3.5 Gateway Time Settings .......................................................................................................28

3.2.4: Login Password Settings ...................................................................................................................29

Figure 3.6 Gateway Login - Change Password Window .....................................................................29

3.2.5: IP Address Change Using an Alternate Method................................................................................30

3.3: Gateway and System Communication Configuration .................................................................................31

3.3.1: Add a Network Connection to the Workstation ................................................................................31

Figure 3.7 Select System To Import From Window ............................................................................31

Table of Contents

6 FocalPoint™ Gateway Installation & Operation Manual - P/N: 52649:Rev: B3 2/11/10

Section 4 FPT Gateway Operation ........................................................................................ 33

4.1: Gamewell Panel Groups ..............................................................................................................................33

4.1.1: Procedure ...........................................................................................................................................33

4.2: Event Handling ............................................................................................................................................34

4.2.1: Handling Special Circumstance Events.............................................................................................34

4.2.2: Node Mapping ...................................................................................................................................34

4.3: Device Commands .......................................................................................................................................35

Table 4.1 Common Gamewell/FCI Device Commands .......................................................................35

4.4: About FCI Point ID Formats for Off Normal Events ..................................................................................35

Table 4.2 FCI 7200 Point ID Formats for Off Normal Events.............................................................35

Table 4.3 FCI 7100 Point ID Formats for Off Normal Events.............................................................35

Table 4.4 FCI E3 Point ID Formats for Off Normal Events ................................................................36

Table 4.5 Gamewell/FCI 7200 Panel Cards .........................................................................................37

4.5: About Auto-created Points...........................................................................................................................37

4.5.1: SmartProgram II Application ............................................................................................................37

Section 5 FocalPoint Gateway Config Tool Reference Information .................................. 39

5.1: About the FocalPoint Gateway Config Tool................................................................................................39

5.2: Field Descriptions ........................................................................................................................................39

5.2.1: Gateway Field Description ................................................................................................................39

Figure 5.1 Version Description.............................................................................................................39

5.2.2: IP Configuration Fields......................................................................................................................39

Figure 5.2 IP Configuration Property/Value Field Descriptions..........................................................39

5.2.3: SNTP Configuration Fields ...............................................................................................................39

Figure 5.3 SNTP Configuration Property/Value Field Description .....................................................39

5.2.4: Time Zone Configuration Fields .......................................................................................................40

Figure 5.4 Time Settings Field Descriptions ........................................................................................40

5.2.5: Panel Properties Fields ......................................................................................................................41

Figure 5.5 Panel Configuration Property/Value Field Descriptions.....................................................41

5.3: Menu Descriptions.......................................................................................................................................41

5.3.1: File .....................................................................................................................................................41

5.3.2: View...................................................................................................................................................41

5.3.3: Configure ...........................................................................................................................................41

5.3.4: Help....................................................................................................................................................41

7FocalPoint™ Gateway Installation & Operation Manual - P/N: 52649:Rev: B3 2/11/10

Section 1 FPT Gateway Overview

1.1 Product Description

This FocalPoint™ Gateway (FPT Gateway):

• Serves as a bridge between a FocalPoint™ Workstation and a Gamewell/FCI network.

• Translates Gamewell/FCI panel and device data into data that can be interpreted by a

FocalPoint™ Workstation.

• Monitors Gamewell/FCI networks over an IP network.

• Is configured using the FocalPoint Gateway Config Tool.

The FPT Gateway is compatible with theses Gamewell/FCI panels.

UL requires the Gamewell/FCI 7200 and E3 panels to have a two line DACT in addition to the

gateway for event reporting.

The FPT Gateway software application resides on a PC board assembly that is installed inside a

supplied cabinet. It communicates with any FocalPoint™ Workstation software application on the

FocalPoint™ system via an IP connection over Ethernet networks.

Every FocalPoint™ system must have at least one:

• FocalPoint™ Workstation

• FocalPoint™ Gateway.

• Gamewell/FCI panel.

Figure 1.1 Basic FPT Gateway Network - Gamewell/FCI

Table 1.1 FPT Gateway Compatibility

IF602 7100

IF610 7200

IF632 E3

IF654

IF658

Workstation

Gateway

Gamewell/FCI

Panel

Ethernet (TCP/IP)

Network

NOTE: Turn on the remote annunciator supervision when connecting the gateway to any of the

stand-alone Gamewell panels.

FPT Gateway Overview Product Description

8 FocalPoint™ Gateway Installation & Operation Manual - P/N: 52649:Rev: B3 2/11/10

Figure 1.2 Advanced FPT Gateway Network - FCI

90.23 effective October 1, 2005

1.1.1 About Workstation Ethernet Network Installations

The FocalPoint™ Workstation is a Proprietary Supervising Station that has a supervised client

server architecture that communicates over IP networks. The Ethernet network can be a shared

bandwidth system that operates over topologies such as an intranet, the Internet, or a frame relay

system.

If the Workstation or gateway is sharing on-premises communications equipment, the shared

equipment shall be “listed for the purpose”. “Listed for the purpose” has been formally interpreted

by NFPA (Formal Interpretation 72-99-1) for equipment on packet switched networks as being

listed to the requirements applicable to general purpose communications network equipment.

For ULC applications, the Internet cannot be used for either primary or ancillary functionality.

Gateway

Workstation

Other Technologies

LAN/WAN/Internet/Intranet

7200

Gateway

Workstation

NOTE: Turn on the remote annunciator supervision on the router to which the gateway connects

for the networked Gamewell panels.

NOTICE TO USERS, INSTALLERS, AUTHORIES HAVING JURISDICTION, AND OTHER INVOLVED PARITES

This product incorporates field-programmable software. In order for the product to comply with the requirements in the Standard

for Control Units and Accessories for Fire Alarm Systems, UL 864, certain programming features or options must be limited to

specific values or not used at all as indicated below.

Program feature or option Permited in UL 864 (Y/N) Possible Settings Settings permitted in UL 864

Remote resetting and

silencing of a fire alarm

control unit from other than

the protected premises (ref:

NFPA 72-2007 6.8.2.8)

No Security Levels

• Administrator

• User with Point Control

• User with Client Control

• Default User

Agency Listings FPT Gateway Overview

9FocalPoint™ Gateway Installation & Operation Manual - P/N: 52649:Rev: B3 2/11/10

1.2 Agency Listings

1.2.1 Compliance

This product has been investigated to, and found to be in compliance with the following standards.

National Fire Protection Association

• NFPA 72—National Fire Alarm Code

Underwriters Laboratories

• UL-864—Control Units for Fire Alarm Systems, Ninth Edition

• UL-1076—Proprietary Burglar Alarm Units and Systems, Fifth Edition

• UL-2017—General-Purpose Signaling Devices and Systems, First Edition

Underwriters Laboratories Canada

• CAN/ULC-S527-99—Standard for Control Units for Fire Alarm Systems, Second Edition

• CAN/ULC-S559-04—Equipment for Fire Signal Receiving Centres and Systems, First

Edition

1.2.2 Installation

This product is intended to be installed in accordance with the following regulatory agencies.

Local

• AHJ—Authority Having Jurisdiction

National Fire Protection Association

• NFPA 70—National Electrical Code

• NFPA 72—National Fire Alarm Code

• NFPA 101—Life Safety Code

Underwriters Laboratories

• UL-1076—In certified applications, the unit shall be installed in accordance with Proprietary

Burglar Alarm Units and Systems, Fifth Edition

Underwriters Laboratories Canada

• C22.1–98—Canadian Electrical Code, Part I (Twentieth Edition), Safety Standard for

Electrical Installation

• CAN/ULC-S524-06—Standard for the installation of Fire Alarm Systems, Fifth Edition

NOTE:

UL 864, 9th Edition—FocalPoint™ systems work with products that have been UL 864, 9th

Edition listed as well as products that have not received UL 864, 9th Edition certification.

Operation of systems that are comprised of equipment that is UL 864, 9th Edition listed together

with products that are not UL 864, 9th Edition listed requires the approval of the local Authority

Having Jurisdiction (AHJ).

CAN/ULC-S559-04, 1st Edition—FocalPoint™ systems work with products that have been

CAN/ULC-S559-04, 1st Edition listed as well as products that have not received CAN/ULC-S559-

04, 1st Edition certification. Operation of systems that are comprised of equipment that is

CAN/ULC-S559-04, 1st Edition listed together with products that are not CAN/ULC-S559-04, 1st

Edition listed requires the approval of the local Authority Having Jurisdiction (AHJ).

FPT Gateway Overview Agency Listings

10 FocalPoint™ Gateway Installation & Operation Manual - P/N: 52649:Rev: B3 2/11/10

• CAN/ULC-S561-03—Installation and Services for Fire Signal Receiving Centres and

Systems, First Edition

1.2.3 Retrofit Applications

The following products have not received UL 864 9th Edition certification and may only be used in

retrofit applications. Operations of the gateway with products not tested for UL 864 9th Edition

has not been evaluated and may not comply with NFPA 72 and/or the latest edition of UL 864.

These applications will require approval of the local Authority Having Jurisdiction (AHJ).

•IF602

•IF610

•IF632

•IF654

•IF658

• FCI 7200

1.2.4 Environmental Requirements

This gateway must be installed in the following environmental conditions:

• Temperature range of 0°C to 49°C (32°F - 120°F).

• 93% humidity non-condensing at 30°C (86°F).

WARNING: Installation

Improper installation, maintenance, and lack of routine testing could result in system malfunction.

Related Documentation FPT Gateway Overview

11FocalPoint™ Gateway Installation & Operation Manual - P/N: 52649:Rev: B3 2/11/10

1.3 Related Documentation

The following is a list of documentation resources related to a UL listed FocalPoint™ system.

• FocalPoint™ Workstation (52561)

NOTE: The contents of this manual are important and must be kept in close proximity of the

hardware. If building ownership is changed, this manual and all other testing and maintenance

information must also be passed to the current owner of the facility. A copy of this manual was

shipped with the equipment and is also available from the manufacturer

FPT Gateway Overview Related Documentation

12 FocalPoint™ Gateway Installation & Operation Manual - P/N: 52649:Rev: B3 2/11/10

13FocalPoint™ Gateway Installation & Operation Manual - P/N: 52649:Rev: B3 2/11/10

Section 2 FPT Gateway Installation

2.1 Required Equipment

The FPT Gateway requires the following:

FPT Gateway Assembly (P/N: FPT-GATE)

The following are shipped with the FPT Gateway:

• FocalPoint™ Gateway PC board (P/N: 46224).

• PNET-1 surge suppressor (P/N: PNET-1).

• CAT5 cable (P/N: 75644) - provides Ethernet connection from gateway PC board to PNET-1

surge suppressor.

• DB9 to leads cable (P/N: 75267) - serial cable that is used as to connect the gateway PC board

to an E3 panel.

• DB9 to RJ-11 cable (P/N: 6100-0077) - provides serial cable to DB9 connector connection.

• Serial Cable (P/N: 6100-0076)- serial cable that is used as to connect the gateway PC board to

a 7100/7200 panels.

• UL Requires the 7200 and E3 panels to have a two line DACT in addition to the gateway for

event reporting.

• Cabinet (P/N: FPT-BA) which includes various screws, hex nuts, star washer, and door lock

key.

• “.010 Formex GK-BK-10 (BLK). UL 94 ZTM-0.”- need to place this insulator in the bottom

of the cabinet in order to meet ULC S527-99 spacing requirements.

• FocalPoint Gateway Config Tool.

• FPT Gateway Manual.

Network Components

• RJ45 to RJ45 standard Ethernet network cable - Network connection to PNET-1 surge

suppressor (supplied by customer).

• Gamewell/FCI Panel (sold separately, Section 1.2.3 on page 10).

• Gamewell Router (P/N: GWPTP-NC) - sold separately.

• FocalPoint™ Workstation computer with software application installed (sold separately).

Customer Supplied Equipment

• A regulated, UL 1481 listed, power limited, battery backed, +24 VDC power supply.

2.2 Installation Overview

• “Cabinet Installation” on page 15.

• “Hardware Installation” on page 16.

WARNING: Installation

Improper installation, maintenance, and lack of routine testing could result in system malfunction.

CAUTION:

Different sources of power are used in conjunction with the FPT Gateway product

. Disconnect all

sources of power before servicing

. This device and associated equipment may be damaged by removing

and/or inserting cards, modules or interconnecting cables while this unit is powered

. This damage may

adversely affect the operation of this unit, but its effect may not be readily apparent.

FPT Gateway Installation Installation Overview

14 FocalPoint™ Gateway Installation & Operation Manual - P/N: 52649:Rev: B3 2/11/10

• “Cable Connections” on page 18.

• “Power Connection” on page 21.

2.2.1 Gateway Board Layout

Figure 2.1 FPT Gateway PC Board Layout

Reset Button

The Reset button is used to cycle power to the PC board. It does not affect the settings made to the

software.

Mode Button

The Mode button is used to return the gateway to all factory settings (i.e. IP address setting). Press

and hold the button for at least 15 seconds to return the gateway to the factory shipped state.

Lithium Battery

The Panasonic BR2032 lithium battery (P/N: 31007) has a factory installed fish-paper-type

insulator between the battery and the battery mounting bracket. Remove the insulator after the PC

board is installed.

Reset ButtonRJ45 Ethernet

Connector

+24VDC Power

Connector

EIA-232 Port +3VDC Lithium

Battery

Mode Button

NOTE: The replacement of the PC board’s lithium battery is to be performed by a trained technician.

WARNING: Electrostatic Discharge

Always observe ESD protection procedures when handling printed circuit boards and electronic

parts.

Cabinet Installation FPT Gateway Installation

15FocalPoint™ Gateway Installation & Operation Manual - P/N: 52649:Rev: B3 2/11/10

2.3 Cabinet Installation

Mount the Gateway cabinet on in inside wall per local requirements.

Step 1. Use the provided door lock key to unlock the cabinet’s door.

Step 2. Remove the cabinet’s door from the back box (reinstall the door when installation is

complete).

Step 3. Mount the cabinet’s back box to the wall using the holes indicated in the following figure.

Figure 2.2 Gateway Cabinet Mounting

Step 4. Connect the required conduit to the desired knock-out location(s) in the cabinet.

Step 5. You are now ready to perform the “Hardware Installation” on page 16.

Conduit

FPT Gateway Installation Hardware Installation

16 FocalPoint™ Gateway Installation & Operation Manual - P/N: 52649:Rev: B3 2/11/10

2.4 Hardware Installation

Step 1. Install the PNET-1 between the gateway cabinet’s standoffs using the supplied hex nut

(#4).

Step 2. Ground the PNET-1 to the cabinet using the supplied hex nut (#6).

Step 3. Install the FocalPoint™ PC board on the gateway cabinet standoffs using the supplied

screws (#4).

Figure 2.3 Gateway Parts Mounting - 1

Step 4. You are now ready to perform “Cable Connections” on page 18.

PNET-1

Gateway

Board

Hex Nut

Stand-off

Hex Nut

4 Screws

Stand-off Conduit

WARNING: Electrostatic Discharge

Always observe ESD protection procedures when handling printed circuit boards and electronic

parts.

NOTE: There is a labeled grounding screw with star washer in the cabinet.

Hardware Installation FPT Gateway Installation

17FocalPoint™ Gateway Installation & Operation Manual - P/N: 52649:Rev: B3 2/11/10

Figure 2.4 Gateway Parts Mounting - 2

FPT Gateway Installation Cable Connections

18 FocalPoint™ Gateway Installation & Operation Manual - P/N: 52649:Rev: B3 2/11/10

2.5 Cable Connections

Connect the Gateway cables as follows:

Step 1. CAT5 cable from gateway PC board to PNET-1 surge suppressor.

Step 2. RJ45 to RJ45 standard Ethernet network cable from FocalPoint™ system’s IP network to

PNET-1.

Step 3. Connect the serial cable:

• Gamewell Panels:

• 600 Series Network: DB9 to lead cable from Gateway PC board's serial

connector to connector on a Gamewell router.

• 600 Series Stand Alone: Cable supplied with panel (RJ11 to DB9) from Gateway

PC board’s serial connector to a Gamewell panel.

•FCI Panels:

• DB9 to lead cable from Gateway PC board’s serial connector to a E3 panel

(Figure 2.9).

• DB9 adapter to RJ-11 serial cable from the Gateway PC board’s serial connector

to a 7100/7200 panel (assembly required refer to Figure 2.10).

Step 4. You are now ready to perform “Power Connection” on page 21.

WARNING: Serial Port Connection

Unless expressly stated otherwise, the FPT Gateway interface requires the exclusive use of any

communication port or terminal to which it connects. The shared use of any communication port or

terminal by this gateway and any ancillary device, such as CRTs or printers, may interfere with or

completely negate the function of this gateway. Such shared connections are not supported.

CAUTION: RPI / SAN / RAN

To ensure proper operation, the FPT Gateway may connected to a 600 series panel using an RPI

(Remote Printer Interface), SAN (Serial Annunciator) or RAN (Remote Annunciator) only if the

gateway version is 3.10.28 or higher.

NOTE: The cable to a 7100 must be in properly sized conduit and less than 20 feet long. The

serial connection from the FocalPoint™ Gateway to the 7100 panel is not supervised.

Cable Connections FPT Gateway Installation

19FocalPoint™ Gateway Installation & Operation Manual - P/N: 52649:Rev: B3 2/11/10

Figure 2.5 Gateway Cable Connections

2.5.1 600 Series Router Serial Data Connection

Figure 2.6 600 Series Router Serial Cable Connection

2.5.2 600 Series Panel Serial Data Connections

Figure 2.7 Direct Serial Data Connection Using the IF602 Supplied Cable

GRN

BLK

RED

X C R G

TB3

DB9 Connector

600 Series Router

DB9 to Leads Cable

P/N: 75267

DB9 Adapter Plug

Serial Cable Supplied with IF602 Panel

To J6

Connector

on IF602

Panel

FPT Gateway Installation Cable Connections

20 FocalPoint™ Gateway Installation & Operation Manual - P/N: 52649:Rev: B3 2/11/10

Figure 2.8 Direct Serial Data Connection Using the Gateway Supplied Cable

2.5.3 FCI Panel Serial Data Connections

Figure 2.9 E3 Serial Cable Connection

Figure 2.10 7100/7200 Serial Cable Assembly/Connection

GRN

BLK

RED

DB9 Connector

To RS232

Connector on

600 Series

Panel

(excludes 602)

Serial Cable Supplied with Gateway

(DB9 to Leads Cable P/N: 75267)

GroundGround

TXRX

RXTX

NOTE: For information about which 600 Series panel’s connectors is used for direct serial data

connections between the gateway and the 600 Series panel consult your respective

Gamewell/FCI panel’s documentation or contact Technical Support.

GRN

BLK

RED

1 2 3 4

TB6

DB9 Connector

E3 Panel’s ILI-MBE3 Board

DB9 to Leads Cable

P/N: 75267

DB9 Adapter Casing

Serial Cable

P/N: 6100-0076

BLK

YLW

RED

Pin 2

Pin 3

Pin 5

DB9 Adapter Plug

DB9 Adapter P/N: 6100-0077

7100/7200

RJ-11

Connector

Insert

NOTE: Some early vintage 7200 panels have a DB9 connector instead of an RJ-11 connector

and such a connection requires a DB9 adapter both ends of the serial cable. Current versions of

firmware are supported but some early versions of firmware may not be supported.

Page is loading ...

Gamewell FCI IF658 Installation & Operation Manual

Brand: Gamewell FCI

Model: IF658

Category: Networking

Type: Installation & Operation Manual

This manual is also suitable for

Download PDF

report

Gamewell FCI IF658 Installation & Operation Manual

This manual is also suitable for

Gamewell FCI IF658 Installation & Operation Manual

Related papers

Other documents