Vax Commercial VCR-02 High Speed Rotary Owner's manual

Vax
Brand
Vax
Model
Commercial VCR-02 High Speed Rotary
Category
Floor Machine
Type
Owner's manual
VCR-01 & VCR-02
Rotary Machine
VCR-01 - Low Speed
VCR-02 - High Speed
User Guide
Vax Commercial Careline: (UK) 0330 026 4275
vaxcommercial.co.uk
A leading brand from one of the world’s
largest oorcare manufacturers.
General Safety Information
2 vaxcommercial.co.uk
WARNING: Always unplug the machine from the mains before conducting
maintenance or troubleshooting checks:
1. The rotary machines (VCR-01 low speed - Ideal for cleaning and
restoration) (VCR-02 high speed - Ideal for polishing of any type
of oor, both natural or treated with metallic waxes) have been
designed for cleaning hard oors and carpets, or polishing
and sanding hard oors.
2. This machine is designed for indoor use only.
3. Important: The machine should only be used by personnel who have
received full training and have carefully read this user guide before
using the machine, performing unscheduled/routine maintenance
or any other work on or with the machine.
4. To avoid unauthorised use, keep the machine in a place where access
by unauthorised personnel is denied.
5. This user guide must be kept in a safe place where it is accessible to all
users and maintenance personnel throughout the life of the machine.
6.
Ensure full compliance with all instructions provided in this manual (paying
particular attention to warnings and danger notices). The manufacturer will
not be held responsible for injuries to persons or damage to property due
to non-compliance with the aforementioned instructions.
7. This machine is designed for use on indoor oors only.
8. Evaluate the type of building where it will be used and comply with
the current safety regulations and conditions.
9. Do not use the machine if the mains cable is damaged. Contact Vax
Commercial Careline: (UK) 0330 026 4275. Monday-Friday 8:30am
to 6:30pm, Saturday and Sunday 9:00am to 5:00pm.
10. Do not operate this machine for any other purpose than for the use for
which it was specically designed.
11.
Do not use the machine in places without adequate lighting, in explosive
environments, when harmful dirt is present (dust, gas, etc.), on roads
or public passageways and in outdoor environments in general.
3Vax Careline: (UK) 0330 026 4275
12. The machine operating temperature range is +4°C to +35°C. When not
being used, store the machine (without pad drive/pad or brush) in a dry
and non-corrosive environment within a temperature range of between
+ 10°C and +50°C. When using the machine under any condition
the humidity must range between 30% and 95%.
13. Do not block or cover any openings.
14. Do not remove, modify or by-pass the safety devices.
15. Only Vax Commercial recommended solutions, tools and accessories
should be used with this machine.
WARNING:
16. The appropriate Personal Protective Equipment should be worn
to operate the machinery and protect the user. This should be in
accordance with an appropriate risk assessment prior to its rst use.
17. Before starting work, remove necklaces, watches, ties and other objects
that may cause serious injuries if caught.
18. Do not insert hands between moving parts.
19. Only clean the machine in accordance with this user guide.
20. Make sure the mains electrical supply is earthed.
21. Always unwind the power cable completely before use.
22. Only use an extension lead that is in perfect condition and is suitable
for the power of the machine (1000W/1600W).
23. Keep the power cable away from sharp objects or edges.
24. Do not adjust the position of the handle while the machine is in use.
25. Do not allow the power cable to come into contact with the rotating
brush or rotating pad.
26. Do not have the machine in a stationery position while the brush
or pad are rotating, as this can cause damage to the oor.
27. Before use ensure there are no obstacles in the path of the machine.
IF YOU FEEL YOU HAVE LOST CONTROL OF THE MACHINE RELEASE
BRUSH ROTATION LEVERS, THE SAFETY SWITCH WILL IMMEDIATELY
DEACTIVATE AND THE MACHINE AND IT WILL STOP!
2
1 Safety/Start button
2 Brush rotation start levers
3 Water supply control lever
(when used in conjunction with the water delivery tank, sold separately)
4 Handle release lever
5 Mains power cable
6 Rotary handle
7 Rotary base
8 Handle to base power cable
9 Drive board
10 Connection socket
(when used in conjunction with the electric
spray kit or vacuum unit, sold separately)
11 Transport wheels
Machine Overview
3
4 vaxcommercial.co.uk
VCR-01 Drive board
VCR-02 Drive board
4
1
5
6
7
8 10
11 11
9
9
2
5Vax Careline: (UK) 0330 026 4275
Preparation
To transport the machine tilt
the machine backwards onto
the wheels. Always remove
the pad or brush before
transporting the machine.
Assembling the rotary machine
Base unit and handle.
Plug the handle power cable
into the base of the unit.
Place the handle on base and
align the four holes with the
holes of the rotary base.
CAUTION: Never attempt to lift the machine.
!
!
!
!
Attach cable
management system.
Using an Allen key (
3
/
10
th
)
size
tighten the four bolts until the
handle is secure.
Preparation
6 vaxcommercial.co.uk
Carefully lay the machine on its back.
Turn anti-clockwise to lock
into place.
Place the brush on the base
of the machine.
Do not t the brush while it is on
the oor. This may damage the
brush connection.
CAUTION: Always ensure the machine is unplugged before attempting to remove
or attach the brush or pad.
CAUTION: Always check the manufactures specic instructions for each oor type when specifying and
using a pad or brush. 17” (inch) brush is only brush size used with the VCR-01 and VCR-02.
CAUTION: Do not use the machine without a brush or pad attached.
CAUTION: Do not use the brush if bristles are splayed or damaged as this may damage the oor.
CAUTION: Vax can not be held responsible for damage to oors where incorrect pads or brush
have been used.
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Attaching the brush
Never leave the brush attached to the machine while it is not in use, in transit or left in contact with the oor for
long periods of time as this may damage the bristles.
✘
Preparation
7Vax Careline: (UK) 0330 026 4275
Attach the pad driver
to the hub of the machine
by making half turns
anti-clockwise to secure.
Attach the pad to the pad
driver, making sure
it is centralised to avoid
unbalanced rotation
or oor damage.
Do not t the pad
while it is on the oor.
This may damage
the drive board connection.
Do not use drive board if
connection is damaged
CAUTION: Do not use the pad if it’s less than 10mm thick as this may damage the oor.
!
!
!
!
!
!
!
!
Attaching the pad
Never leave the pad attached to the machine while it is not in use, in transit or left in contact with the oor for
long period of time as this may damage the pad.
CAUTION: If the brush/pad is not correctly tted the machine will jump and judder.
!
!
!
!
✘ ✘
✔
Carefully lay the machine
on its back.
CAUTION: Always ensure the machine is unplugged before attempting to remove or attach the brush or pad.
✘
Operation
8 vaxcommercial.co.uk
Adding extra weight to the machine (VCR- 01 only)
CAUTION: Due to the increased contact pressure with the oor, wear of the brush and pad will increase.
The brush and pad will experience more rapid wear and tear.
CAUTION: Only use the additional weight supplied by the Vax. Using other weights can compromise
the safety of the machine and could damage the oor.
!
!
!
!
!
!
!
!
If the surface is particularly dirty, an additional weight can be attached to the machine to allow the brush
or pad to have greater contact pressure with the oor for a deeper clean.
Lift the additional weight using the special recesses.
Place the weight onto the body of the machine.
!
!
!
!
!
!
!
!
CAUTION: Always ensure the machine is unplugged before attempting to add additional weight.
CAUTION: Position ngers under recesses to ensure there is no possibility that ngers will become trapped.
!
!
!
!
!
!
!
!
CAUTION: It is recommended that extra weight is
removed from unit when not in use or in storage.
CAUTION: Do not leave machine resting on brush,
drive board or pad for long periods as may damage
or misshapen said articles.
Operation
9Vax Careline: (UK) 0330 026 4275
Practice operation
Practice lifting and lowering the handle, then releasing the brush rotation levers. Do this 4 or 5 times before each
use to familiarise yourself with this action. Practising this procedure will make sure the machine always remains
in your control.
Unwind the power cable, plug
the machine into the mains
and switch on.
Practice releasing the brush
rotation levers.
Controlling the machine
Lift the handle release lever.
Lift/lower the handle. Always
keep 2 hands on the control
handle whilst in operation.
Lower the handle to the optimum
operation height (hip height).
Simultaneously press the
safety/starting button (A) and
both brush rotation levers (B)
to start the machine.
A
B
B
CAUTION: Large movements of the handle up (to move left) or down (move right) will cause the machine to
move quickly. The user may feel like the machine is no longer within their control, the natural reaction to this
is to grip the handle tighter. This will not stop the machine and may cause the machine to move more rapidly.
The machine will only automatically stop if the brush rotation levers are released.
IMPORTANT: It is vital that during training and before rst use, the user practices stopping the machine, to
ensure no harm is caused to the user or surrounding areas.
CAUTION: Do not let the mains power cable come in contact with the rotating brush or pad.
CAUTION: When practicing this procedure ensure that you use dierent areas of the oor each time.
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
P
R
A
C
T
I
C
E
Operation
10 vaxcommercial.co.uk
Unwind the power cable, plug
the machine into the mains
and switch on.
Cleaning operation
Lift the handle release lever.
Simultaneously press the
safety/starting button (A)
and both brush rotation levers
(B) to start the machine.
Always keep two hands
on the control handle
whilst in operation.
A
B
B
Lower the handle to the
optimum operation
height (hip height).
CAUTION: Before use make sure there are no obstacles in the way of the cleaning area. Never wrap the
power cable around the neck or the body of the machine while in use. Before use check the condition of
brush/pad and replace if there are frayed/damaged bristles or if pad thickness is less than 10mm thick.
Do not leave pad or brush attached while the machine is not in use.
CAUTION: The machine should only be used by personnel who have received full training and have
carefully read this user guide before using the machine, performing unscheduled/routine maintenance
or any other work on or with the machine.
!
!
!
!
!
!
!
!
!
!
!
!
IMPORTANT: IF YOU FEEL YOU
HAVE LOST CONTROL OF THE
MACHINE, LET GO OF THE BRUSH
ROTATION LEVERS. THE SAFETY
SWITCH WILL IMMEDIATELY
DEACTIVATE THE MACHINE
AND IT WILL STOP!
Operation
11Vax Careline: (UK) 0330 026 4275
Once nished unplug from
mains. Remove the brush
or pad and pad drive from the
machine to avoid brush or pad
damage. The machine should
be left in the parking position
with the handle upright.
For best results the machine
must be moved in small
steady arcs rotating
from left to right whilst
moving backwards.
To move left or right, keep
the rotation levers pressed
and handle positioned at hip
height. To move right, gently
lift the handle up. To move left
gently lower the handle down.
To move forward or back,
keep the rotation levers
pressed. With the handle
positioned at the optimum
operation height (hip height)
walk forward or backwards.
To stop the machine, release
the brush rotation levers.
Maintenance
12 vaxcommercial.co.uk
Cleaning the machine
CAUTION: Always ensure the machine is unplugged before carrying out any maintenance/troubleshooting.
CAUTION: Do not use solvents, acids or corrosive substances to clean the machine.
!
!
!
!
The pad thickness should
always be between 10-20mm.
Do not use the pad if its less
than 10mm thick as this may
damage the oor. Do not use
the brush if bristles are
splayed or damaged as this
may damage the oor.
Clean the brush or pad under
running water (max 60°c)
and leave to dry. To avoid
damaging the oor and the
machine, carefully check
if debris, such as grit, metallic
parts, screws, chips, cords
or similar items, have become
lodged in the brush or pad.
Use a sponge or a soft
cloth to clean the exterior
of the machine.
Carefully lay the machine on its back and remove the brush or pad. With a damp cloth wipe clean
and remove any dirt and debris
from inside the rotary base.
!
!
!
!
Max 60°
water
✘
✔
Maintenance
13Vax Careline: (UK) 0330 026 4275
The pad or brush should be cleaned and stored with
the pad or brush facing upwards to avoid causing damage
to the useable surface.
The machine should be stored in the parking position
with the handle upright, cable wrapped around
the hooks and without the brush or pad/pad drive attached.
Storage
Never leave the brush, pad or drive board attached while the machine is not in use as this may damage
the bristles/pad.
Troubleshooting
14 vaxcommercial.co.uk
Why does the machine have no power?
• The plug may not be pushed fully into the electrical socket.
• Check the fuse in the plug. If this needs replacing, always replace with a British 13amp fuse.
• The handle is not reclined. Recline and retry.
• The safety/starting button has not been activated or the brush rotation levers have not been squeezed.
• The handle cable is loose or has been unplugged from machine. Reconnect
• The cable is damaged, for assistance contact Vax Commercial Careline: (UK) 0330 026 4275.
• The electrical connector on the base is not pushed home, plug in connector.
Why does the brush/pad not rotate?
• The handle is not reclined. Recline and retry.
• The safety/starting button has not been activated or brush rotation levers have not been squeezed.
• The brush has not been correctly tted. Ret brush.
• Unplug machine and carefully lay on its back, check there are no objects blocking the drive board.
• The electrical connector on the base is not pushed home, plug in connector.
The oor is not clean or there is uneven cleaning.
• Check that the brush or pad is not worn. – Go to ‘Maintenance’ (page 11).
• Make sure that the brush or pad has been secured centrally on the machine.
The machine operates erratically or vibrates heavily.
• Check that the brush or pad is not worn. If so replace the brush or pad.
• Check that the brush or pad drive is not damaged.
• The machine has been left stationary for a period of time with brush/pad attached.
This will stop after a few minutes.
• Make sure that the brush or pad has been secured centrally on the machine.
What do I do if the unit/an accessory becomes damaged or broken?
• We’re here to help. Simply call 0330 026 4275 or visit vaxcommercial.co.uk
CAUTION: To reduce the risk of personal injury, unplug the rotary machine from mains supply before
performing maintenance/troubleshooting checks.
!
!
!
!
Service and help
15Vax Careline: (UK) 0330 026 4275
EEC Statement of Compliance
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the
VCR-01\02 series is manufactured in compliance with the following Directives:
Safety: 2006/42/CE(+2009/127/EC), 2004/108/CE, EN60335-1, EN60335-2-67 Low Voltage Directive
EMC: 2004/108/EC Electromagnetic Compatibility Directive Disposal
Disposal
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
Vax Commercial Careline:
(UK) 0330 026 4275
Monday-Friday 8:30am to 6:30pm, Saturday and Sunday 9:00am to 5:00pm
Any queries or concerns about using your Vax, call the Vax Commercial Careline. Calls are charged at the UK
local rate. Please make a note of the serial number and model number of the machine cleaner before calling.
Technical Specication
VCR-01 (low speed)
Power: 240V
Wattage 1000W
Cleaning speed: 154 rpm
Contact pressure: 41.3g/cm
2
Cleaning width: 430mm (17”)
Noise: 54 dB(A)
Cable: 12m
Weight: 42kg
Dimensions: 1200 x 542 x 430 cm
Technical Specication
VCR-02- (high speed)
Power: 240V
Wattage: 1600W
Cleaning speed: 400 rpm
Contact pressure: 44.3g/cm
2
Cleaning width: 430mm (17”)
Noise: 56 dB(A)
Cable: 12m
Weight: 42kg
Dimensions: 1200 x 542 x 430 cm
Consumables
To purchase spares and accessories please visit vaxcommerical.co.uk or call 0330 026 4275.
Subject to technical change without notice.
Version 1
A leading brand from one of the world’s
largestoorcare manufacturers.
Vax Ltd., 5th Floor 2 Colmore Square, 38 Colmore Circus, Queensway, Birmingham, B4 6BN, UK
email: inf[email protected] website: vax.co.uk
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Vax Commercial VCR-02 High Speed Rotary Owner's manual

Vax
Brand
Vax
Model
Commercial VCR-02 High Speed Rotary
Category
Floor Machine
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents