Wacker Neuson EH 50/230 25x108 User manual

Operator´s manual

Electric hammer

EH 50

09.2015

5100005269

en/ 05

Manufacturer

Wacker Neuson Produktion GmbH & Co. KG

Preußenstraße 41

80809 München

www.wackerneuson.com

Tel.: +49-(0)89-354 02-0

Fax: +49-(0)89-354 02-390

Translation of the original operator's manual in German

5100005269IVZ.fm 3

1 Foreword ....................................................................................................................5

2 Introduction ...............................................................................................................6

2.1 Means of representation for this operator's manual....................................................... 6

2.2 Wacker Neuson representative...................................................................................... 7

2.3 Described machine types............................................................................................... 7

2.4 Identification of the machine .......................................................................................... 8

3 Safety .........................................................................................................................9

3.1 Principle ......................................................................................................................... 9

3.2 Qualification of the operating personnel....................................................................... 12

3.3 Protective gear............................................................................................................. 13

3.4 Transport...................................................................................................................... 14

3.5 Operating safety........................................................................................................... 14

3.6 Safety during the operation of hand machines............................................................. 16

3.7 Safety during the operation of electric appliances ....................................................... 17

3.8 Maintenance................................................................................................................. 18

4 General Power Tool Safety Warnings ...................................................................20

5 Safety and information labels ................................................................................24

6 Structure and function ...........................................................................................25

6.1 Scope of delivery.......................................................................................................... 25

6.2 Application.................................................................................................................... 25

6.3 Functionality................................................................................................................. 25

7 Components and operator's controls ...................................................................26

8 Transport .................................................................................................................27

9 Use and operation ...................................................................................................28

9.1 Prior to starting the machine........................................................................................ 28

9.2 Changing tools............................................................................................................. 28

9.3 Starting up.................................................................................................................... 30

9.4 Switching on the machine............................................................................................ 31

9.5 Decomissioning............................................................................................................ 32

10 Maintenance ............................................................................................................33

10.1 Maintenance personnel qualifications.......................................................................... 33

10.2 Maintenance schedule................................................................................................. 33

10.3 Maintenance work........................................................................................................ 34

10.3.1 Visual inspection for damage.......................................................................... 34

10.3.2 Cleaning the machine ..................................................................................... 34

10.3.3 Lubricating the machine.................................................................................. 35

10.3.4 Checking the tool holder for wear ................................................................... 36

Inhalt

4

5100005269IVZ.fm

11 Troubleshooting ......................................................................................................37

12 Disposal ...................................................................................................................38

12.1 Disposal of waste electrical and electronic equipment................................................. 38

13 Accessories .............................................................................................................39

13.1 Truck............................................................................................................................. 39

14 Technical data .........................................................................................................41

14.1 Extension cable............................................................................................................ 45

15 Glossary ...................................................................................................................46

EC Declaration of Conformity ................................................................................49

DIN EN ISO 9001 Zertifikat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

1 Foreword

100_0000_0002.fm 5

1Foreword

This operator's manual contains information and procedures for the safe opera-

tion and maintenance of your Wacker Neuson machine. In the interest of your

own safety and to prevent accidents, you should carefully read through the safety

information, familiarize yourself with it and observe it at all times.

This operator's manual is not a manual for extensive maintenance and repair

work. Such work should be carried out by Wacker Neuson service or authorized

specialists.

The safety of the operator was one of the most important aspects taken into con-

sideration when this machine was designed. Nevertheless, improper use or in-

correct maintenance can pose a risk. Please operate and maintain your Wacker

Neuson machine in accordance with the instructions in this operator's manual.

Your reward will be troublefree operation and a high degree of availability.

Defective machine parts must be replaced immediately!

Please contact your Wacker Neuson representative if you have any questions

concerning operation or maintenance.

No part of this publication may be reproduced in any form or by any means, elec-

tronic or mechanical, including photocopying, without the expressed written per-

mission of Wacker Neuson.

Any type of reproduction, distribution or storage on data media of any type and

form not authorized by Wacker Neuson represents an infringement of copyright

and will be prosecuted.

We expressly reserve the right to make technical modifications – even without

special notice – which aim at further improving our machines or their safety stan-

dards.

2 Introduction

6

100_0000_0003.fm

2 Introduction

2.1 Means of representation for this operator's manual

Warning symbols

This operator's manual contains safety information of the categories:

DANGER, WARNING, CAUTION, NOTICE.

They should be followed to prevent danger to life and limb of the operator or dam-

age to equipment and exclude improper service.

Notes

Note: Complementary information will be displayed here.

DANGER

This warning notice indicates immediate hazards that result in serious injury or

even death.

 Danger can be avoided by the following the actions mentioned.

WARNING

This warning notice indicates possible hazards that can result in serious injury

or even death.

 Danger can be avoided by the following the actions mentioned.

CAUTION

This warning notice indicates possible hazards that can result in minor injury.

 Danger can be avoided by the following the actions mentioned.

NOTICE

This warning notice indicates possible hazards that can result in material dam-

age.

 Danger can be avoided by the following the actions mentioned.

2 Introduction

100_0000_0003.fm 7

Instructions

 This symbol indicates there is something for you to do.

1. Numbered instructions indicate that you have to carry out something in a de-

fined sequence.

 This symbol is used for lists.

2.2 Wacker Neuson representative

Depending on your country, your Wacker Neuson representative is your Wacker

Neuson service, your Wacker Neuson affiliate or your Wacker Neuson dealer.

You can find the addresses in the Internet at www.wackerneuson.com.

The address of the manufacturer is located at the beginning of this operator's

manual.

2.3 Described machine types

This operator's manual is valid for different machine types from a product range.

Therefore some figures can differ from the actual appearance of your machine.

It is also possible that the descriptions include components which are not a part

of your machine.

Details for the described machine types can be found in the chapter Technical

data.

2 Introduction

8

100_0000_0003.fm

2.4 Identification of the machine

Nameplate data

The nameplate lists information that uniquely identifies your machine. This infor-

mation is needed to order spare parts and when requesting additional technical

information.

 Enter the information of your machine into the following table:

Item Designation Your information

1 Group and type

2 Construction year

3 Machine no.

4 Version no.

5 Item no.

3 Safety

100_0301_si_0001.fm 9

3 Safety

3.1 Principle

State of the art

This machine has been constructed with state-of-the-art technology according to

the recognized rules of safety. Nevertheless, when used improperly, dangers to

the life and limb of the operator or to third persons or damage to the machine or

other materials cannot be excluded.

Proper use

The machine must only be used for the following purposes:

 Breaking off concrete and asphalt and soil that is full of boulders.

 Breaking off concrete, masonry and other construction materials, untouched

and frozen ground.

 Scarifying roads and concrete, asphalt, tar and wooden and stone paving.

 Cutting clay, loam, peat and salts.

 Breaking up compacted soils.

 Ramming in posts, probes and grounding rods.

The machine may only be used with tools that are intended for use with the ma-

chine and the material being worked on.

The machine may not be used for the following purposes:

 Working on hazardous materials such as asbestos.

Its proper use also includes the observance of all instructions contained in this

operator's manual as well as complying with the required service and mainte-

nance instructions.

Any other use is regarded as improper. Any damage resulting from improper use

will void the warranty and the liability on behalf of the manufacturer. The operator

assumes full responsibility.

3Safety

10

100_0301_si_0001.fm

Structural modifications

Never attempt to modify the machine without the written permission of the man-

ufacturer. To do so will endanger your safety and the safety of other people! In

addition, this will void the warranty and the liability on behalf of the manufacturer.

Especially the following are cases of structural modifications:

 Opening the machine and the permanent removal of components from

Wacker Neuson.

 Installing new components which are not from Wacker Neuson and not equiv-

alent to the original parts in design and quality.

 Installation of accessories which are not from Wacker Neuson.

It is no problem to install spare parts from Wacker Neuson.

It is no problem to install accessories that are available in the Wacker Neuson

product range of your machine. Please refer to the installation regulations in this

operator's manual.

Do not drill into the housing, e.g. to install signs. Water could penetrate the hous-

ing and damage the machine.

Requirements for operation

The ability to operate the machine safely requires:

 Proper transport, storage and setup.

 Careful operation.

 Careful service and maintenance.

Operation

Operate the machine only as intended and only when in proper working condi-

tion.

Operate the machine in a safety-conscious manner with all safety devices at-

tached and enabled. Do not modify or disable any safety devices.

Before starting operation, check that all control and safety devices are function-

ing properly.

Never operate the machine in a potentially explosive environment.

Maintenance

Regular maintenance work is required in order for the machine to operate prop-

erly and reliably over time. Failure to perform adequate maintenance reduces the

safety of the machine.

 Strictly observe the prescribed maintenance intervals.

 Do not use the machine if it requires maintenance or repairs.

3 Safety

100_0301_si_0001.fm 11

Malfunctions

If you detect a malfunction, you must shut down and secure the machine imme-

diately.

Eliminate the malfunctions that impair safety immediately!

Have damaged or defective components replaced immediately!

For further information, refer to chapter Troubleshooting.

Spare parts, accessories

Use only spare parts from Wacker Neuson or such that are equivalent to the orig-

inal parts in design and quality.

Only use accessories from Wacker Neuson.

Non-compliance will exempt the manufacturer from all liability.

Exclusion of liability

Wacker Neuson will refuse to accept liability for injuries to persons or for damage

to materials in the following cases:

 Structural modifications.

 Improper use.

 Failure to comply with this operator's manual.

 Improper handling.

 Using of spare parts which are not from Wacker Neuson and not equivalent

to the original parts in design and quality.

 Using of accessories which are not from Wacker Neuson.

Operator's manual

Always keep the operator's manual near the machine or near the worksite for

quick reference.

If you have misplaced the operator's manual or require an additional copy, con-

tact your Wacker Neuson representative or download the operator's manual from

the Internet (www.wackerneuson.com).

Always hand over this operator's manual to other operators or to the future owner

of the machine.

Country-specific regulations

Observe the country-specific regulations, standards and guidelines in reference

to accident prevention and environmental safety, for example those pertaining to

hazardous materials and wearing protective gear.

Complement the operator's manual with additional instructions taking into ac-

count the operational, regulatory, national or generally applicable safety guide-

lines.

3Safety

12

100_0301_si_0001.fm

Operator's controls

Always keep the operator's controls of the machine dry, clean and free of oil or

grease.

Operating elements such as ON/OFF switch, gas handles etc. may not be

locked, manipulated or changed without authorization.

Checking for signs of damage

Inspect the machine when it is switched off for any signs of damage at least once

per work shift.

Do not operate the machine if there is visible damage or defects.

Have any damage or defects eliminated immediately.

3.2 Qualification of the operating personnel

Operator qualifications

Only trained personnel are permitted to start and operate the machine. The fol-

lowing rules also apply:

 You are physically and mentally fit.

 You have received instruction on how to independently operate the machine.

 You have received instruction in the proper use of the machine.

 You are familiar with required safety devices.

 You are authorized to start machines and systems in accordance with the

standards governing safety.

 Your company or the operator has assigned you to work independently with

this machine.

Incorrect operation

Incorrect operation or misuse by untrained personnel can endanger the health

and safety of the operator or third persons and also cause machine and material

damage.

Operating company responsibilities

The operating company must make the operator's manual available to the oper-

ator and ensure that the operator has read and understood it.

3 Safety

100_0301_si_0001.fm 13

Work recommendations

Please observe the recommendations below:

 Work only if you are in a good physical condition.

 Work attentively, particularly as you finish.

 Do not operate the machine when you are tired.

 Carry out all work calmly, circumspectly and carefully.

 Never operate the machine under the influence of alcohol, drugs or medica-

tion. This can impair your vision, reactions and your judgment.

 Work in a manner that does not endanger others.

 Ensure that no persons or animals are within the danger zone.

3.3 Protective gear

Work clothing

Clothing should be appropriate, i.e. should be close-fitting but not restrict your

movement.

When on construction sites, do not wear long hair loosely, loose clothing or jew-

elry including rings. These objects can easily get caught or be drawn in by mov-

ing machine parts.

Only wear clothing made of material that is not easily flammable.

Personal protective gear

Wear personal protective gear to avoid injuries or health hazards:

 Non-skid, hard-toed shoes.

 Work gloves made of durable material.

 Overalls made of durable material.

 Hard hat.

 Ear protection.

 Face protection.

 Eye protection.

 Breathing protection in the case of dusty ambient air.

Ear protection

This machine generates noise that exceeds the country-specific permissible

noise levels (individual rating level). It may therefore be necessary to wear ear

protection. You can find the exact value in the chapter Technical Data.

When wearing ear protection while working, you must pay attention and exercise

caution because your hearing is limited, e.g. in case someone screams or a sig-

nal tone sounds.

Wacker Neuson recommends that you always wear ear protection.

3Safety

14

100_0301_si_0001.fm

3.4 Transport

Switching off the machine

Before you transport the machine, switch it off and pull the plug out of the plug

receptacle. Allow the motor to cool down.

Transporting the machine

Secure the machine on the transport device against tilting, falling or slipping.

Lifting the machine

A falling machine can cause serious injuries.

The machine has no lifting or lashing points.

When lifting the machine, secure it in a closed transport container or similar in

order to prevent it from toppling, falling or slipping away.

Restarting

Machines, machine parts, accessories or tools that were detached for transport

purposes must be re-mounted and fastened before restarting.

Only operate in accordance with the operating instructions.

3.5 Operating safety

Explosible environment

Never operate the machine in a potentially explosive environment.

Work environment

Familiarize yourself with your work environment before you start work. This in-

cludes e.g. the following items:

 Obstacles in the work and traffic area.

 Load-bearing capacity of the ground.

 The measures needed to cordon off the construction site from public traffic in

particular.

 The measures needed to secure walls and ceilings.

 Options available in the event of an accident.

3 Safety

100_0301_si_0001.fm 15

Safety in the work area

When working with the machine especially pay attention to the following points:

 Electric lines or pipes in work area.

 Gas lines or water lines in the work area.

 Material becoming separated, dropping down or ejected. Make sure that you

do not put other persons in danger.

 Pay maximum attention in the vicinity of drops or slopes. Risk of falling.

 Maintain a sufficient distance from flammable materials.

Checks before starting work

Check the following points before beginning work:

 Condition of tools.

 Machine settings.

 Connection value of the machine.

Starting the machine

Observe the safety information and warning notices located on the machine and

in the operator's manual.

Never attempt to start a machine that requires maintenance or repairs.

Start the machine as described in the operator's manual.

Vertical stability

Always make sure that you stand firmly when working with the machine. This ap-

plies particularly when working on scaffoldings, ladders, uneven or slippery

floors etc.

Caution with hot parts

Do not touch any hot parts such as tools, tool holders or guide cylinders during

operation or directly afterwards. These parts can become very hot and can cause

severe burns.

Caution with movable parts

Keep your hands, feet and loose clothing away from moving or rotating machine

parts. Parts of your body being pulled in or crushed can cause serious injuries.

Caution with toxic materials

Some materials may contain toxic chemicals which are released during demoli-

tion. Therefore personal protective equipment must be worn to prevent inhalation

of and skin contact with work dust.

3Safety

16

100_0301_si_0001.fm

Do not direct towards people

Do not direct the machine towards people in the vicinity during operation. The

tool might be flung out and cause serious injuries.

No persons endangered

Be sure that no persons are endangered by flying or falling materials. Always

work very attentively, and anticipate potential hazards.

Switching off the machine

Switch off the machine and pull the plug out of the plug receptacle in the following

situations:

 Before breaks.

 If you are not using the machine.

 If you are changing the tool.

 If you are removing chips or splinters.

Before storing the machine, wait until it has completely stopped running.

Store the machine or put it down in such a way that it cannot tilt, fall down or slip.

Storage

Set the machine down or store it securely so that it cannot tilt, fall down or slip.

Storage location

After operation, allow the machine to cool and then store it in a sealed-off, clean

and dry location protected against frost and inaccessible to children.

3.6 Safety during the operation of hand machines

Safe working with hand machines

Secure loose workpieces with suitable methods.

While working, as a rule hold the machine on the provided handles with both

hands.

While working, hold the machine in such a way that hand injuries are avoided

when hitting hard objects.

Setting the hand machine down properly

Set the machine down carefully. Do not drop the machine to the floor or from

greater heights. Dropping the machine can cause injuries to other persons or the

machine itself can be damaged.

3 Safety

100_0301_si_0001.fm 17

Safe working with the hammer

Keep the tool holder closed during operation.

Guide the power cable always from the machine to the rear and keep the power

cable away from the working range of the machine.

3.7 Safety during the operation of electric appliances

Specific regulations for electrical appliances

Observe the safety information provided in the brochure General Safety Rules

which is included in the scope of delivery of your machine.

Also observe the country-specific regulations, standards and guidelines in refer-

ence to accident prevention in connection with electrical equipment and ma-

chines.

WARNING Read all safety information and instructions. Failure to follow

the safety information and instructions may result in electric shock, fire and/or se-

rious injury.

Save all safety information and instructions for future reference.

Electric power supply for electrical appliances of class rating II

Note: The rated voltage is indicated on the nameplate of your machine.

The machine may only be connected to an electric power supply with all machine

parts in proper working condition. Take special notice of the following compo-

nents:

 Plug.

 Power cable over the entire length.

 Switch diaphragm of the ON/OFF switch, if there is one.

 Plug receptacles.

Electrical appliances of class rating II have a strengthened or double insulation

(protective insulation). They have no connection to the grounded conductor.

There must be at least one of the following safety devices if connected to a sta-

tionary or mobile generator:

 Fault current protective switch.

 Isolation (earth leakage) monitor.

 IT-net.

Note: Observe the respective national safety regulations!

3Safety

18

100_0301_si_0001.fm

Extension cable

The machine may only be operated with undamaged and tested extension ca-

bles!

Only use extension cables with grounded conductor and correct connection of

the grounded conductor to the plug and coupling (only for machines of class rat-

ing I, see chapter Technical data).

Only use tested extension cables which are suitable for use at construction sites:

Average rubber hose H05RN-F or better – Wacker Neuson recommends

H07RN-F, an SOOW cable, or a country-specific equivalent design.

Immediately replace damaged extension cables (e.g. tears in the sheathing) or

loose plugs and couplings.

Cable drums and multiple plug receptacles must fulfill the same requirements as

the extension cable.

Protect extension cables, multiple plug receptacles, cable drums and connection

couplings against rain, snow or any other forms of moisture.

Uncoil the cable drum completely

Danger of fire due to wound cable drum.

Uncoil the cable drum completely before operation.

Protecting the power cable

Do not use the power cable to pull or lift the machine.

Do not unplug the power cable by pulling on the cable.

Protect the power cable from heat, oil and sharp edges.

If the power cable is damaged or the plug is loose, have it replaced immediately

by your Wacker Neuson representative.

Protecting from moisture

Protect the machine against rain, snow or any other forms of moisture. This could

cause damage or other malfunctions.

3.8 Maintenance

Maintenance work

Service and maintenance work must only be carried out to the extent described

in these operating instructions. All other procedures must be performed by your

Wacker Neuson representative.

For further information, refer to chapter Maintenance.

3 Safety

100_0301_si_0001.fm 19

Disconnecting the machine from the electric power supply

Before carrying out service or maintenance work, pull the plug out of the plug re-

ceptacle in order to disconnect the machine from the electric power supply.

Cleaning

Always keep the machine clean and be sure to clean it each time you have fin-

ished using it.

Do not use gasoline or solvents. Danger of explosion!

Do not use high pressure washers. Permeating water can damage the machine.

When electrical equipment is present, this can pose a serious injury risk from

electric shocks.

Cleaning the zerk fitting

Wipe the zerk fitting with a clean cloth after the lubrication of the machine. There

is a danger of electrocution if there is excessive grease on the zerk fitting.

4 General Power Tool Safety Warnings

20

100_0301_si_0008.fm

4 General Power Tool Safety Warnings

WARNING Read all safety warning, instructions, illustrations and specifications

provided with this power tool. Failure to follow all instructions listed below may result in electric

shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warning refers to your mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust.

c) Power tools create sparks which may ignite the dust or fumes.

d) Keep children and bystanders away while operating a power tool.

e) Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not

use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is

earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged

or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

Page is loading ...

Wacker Neuson EH 50/230 25x108 User manual

This manual is also suitable for

Wacker Neuson EH 50/230 25x108 User manual

Related papers

Other documents