Sanyo CLT-2415 User manual

CLT-2415

INSTRUCTION MANUAL

2.4-GHz

Digital Spread Spectrum

Cordless Telephone

with Call Manager Features

IMPORTANT

Charge the handset battery pack for a full 15 hours before using your

cordless handset for the first time.

www.sanyocanada.com

CLT2415 ENG-6/20 6/20/01 19:07 Page i

Congratulations on your purchase of the CLT-2415 cordless telephone.

This phone is designed for reliability, long life, and outstanding performance utilizing the

latest in 2.4 GHz Digital Spread Spectrum technology.

Note: Some illustrations in this manual may differ from the actual unit for

explanation purposes.

● 2.4 GHz Digital Spread Spectrum Technology

● Call Manager Features*: Caller ID, Caller ID on Call Waiting and Call Waiting with Options

*Each feature works with your network service. A subscription required.

● 50-Number Caller ID List

● 3-Line, 16-Character Backlit Handset Display

● Lighted Handset Keypad and TALK/END Key

● 20-Name/Number Directory

● Last 3-Number Redial

● 10-Day Standby Battery Life/6-Hour Talk Time

● Reversible Handset Charging

● 35-Channel Auto/Manual Scan

● Digital Security Code

● Call Time Display

● Pulse/Tone Dialing

● Page/Handset Locator

● Handset Earpiece/Volume Control

● Ringer Volume Control with Off Setting

● Belt Clip and Headset Jack

● Wall-Mountable

● Hearing Aid Compatible

2.4-GHz Digital Spread Spectrum Technology utilizes a “wider frequency band”

vs. a “single narrow band” used in standard digital transmissions. The result is the

clarity of digital sound, extended range and a secure conversation with virtually no

interference from other 2.4 GHz cordless phones or radio transmission devices.

The clearest channel is automatically selected for each transmission. The phone

selects one of over 65,000 digital security codes for the handset and base.

These features enhance your phone’s security and also prevent unauthorized calls

as a result of your phone being activated by other equipment.

Introduction

Features

CLT2415 ENG-6/20 6/20/01 19:09 Page ii

1. Handset antenna

2. Headset jack cover

3. Battery compartment

4. Earpiece speaker

5. LCD display

6. MEMORY key

7. TALK/END key

8. CALL REVIEW/VOLUME (down) key

9.

L

eft cursor key (TONE/

*

/)

10. REDIAL/PAUSE key

11. MENU key

12. Microphone

13. CALL REVIEW/VOLUME (up) key

14. FLASH key

15. CID key

16. Right cursor key ( )

17. DELETE key

18. SELECT/SCAN key

19. Handset charging contacts

Controls and functions

1

2

3

4

5

6

7

8

9

12

10

11

14

15

18

19

17

16

13

CLT2415 ENG-6/20 6/20/01 19:07 Page iii

21

20

22

25

23

24

26 27 28

20. Bottom bracket

21. Handset retainer

22. Base charging contacts

23. PAGE/FIND key

24. CHARGE/IN USE indicator

25. Base antenna

26. Pulse-Tone switch

27. DC power input

28. Phone jack

CLT2415 ENG-6/20 6/20/01 19:07 Page iv

E1

Introduction/Features ..............................................inside front cover

Controls and Functions............................................inside front cover

Getting started

Read this first..........................................................................................E2

Step 1: Checking the package contents .........................................E3

Step 2: Setting up the base unit ........................................................E4

Desktop use ..............................................................................E5

Mounting the base unit on a wall .......................................E7

Step 3: Preparing the battery pack ...................................................E9

Basics

Making a call ........................................................................................E11

Receiving a call....................................................................................E13

Call Waiting ..........................................................................................E13

Lighted keypad ....................................................................................E14

Scanning ...............................................................................................E14

Adjusting the ringer and earpiece volume...................................E14

Redialing a call.....................................................................................E15

Directory

Caller ID

Features

Advanced Calling

Features

CONTENTS

Additional

Information

CLT2415 ENG-6/20 6/20/01 19:07 Page 1

E2

This cordless telephone must be set up before use. Follow these steps:

Step 1 (page E3)

Unpack and check the telephone and accessories.

Step 2 (pages E4 to E8)

Choose the best location to set

up the base unit.

Base unit

Step 3 (pages E9 to E10)

Insert the battery pack into the handset. You

must charge the battery pack for a full 15 hours

before using the phone.

Handset

About the digital security code

This cordless telephone uses a digital security code to prevent unauthorized access to

your base unit. This security code prevents other cordless handsets from making calls

through your base unit.

A random security code will be assigned automatically between your base unit and

handset when you charge the battery pack for the first time.

If you want to reset the security code, see page E37.

GETTING

STARTED

Read this first

CLT2415 ENG-6/20 6/20/01 19:07 Page 2

E3

Make sure you have received the following items in the package.

• Base unit

• Handset

• AC adaptor

(AD-350)

• Rechargeable

battery pack

(SANYO 3KR-800AAE)

• Telephone line

cord (1)

• Bottom bracket

for desktop use

and wall-mounting

• This Owner's Manual

• Belt clip

Checking the package contents

GETTING

STARTED

CLT2415 ENG-6/20 6/20/01 19:07 Page 3

E4

Avoid places near electrical equipment such as refrigerators, computers, TVs,

microwaves or fluorescent lamps. These may cause interference or reduce the operating

range of the cordless telephone.

Do the following steps:

• Choose the best location

• Connect the base unit

• Choose the dialing mode

• The location should be close to both a phone jack and a continuous power outlet which is

not switchable.

• Be sure there is sufficient space to raise the base antenna fully to a vertical position.

• The base can be placed on a desk, tabletop or mounted on a standard wall plate.

Notes:

Setting up the base unit

GETTING

STARTED

CLT2415 ENG-6/20 6/20/01 19:07 Page 4

When connecting the power cord, make sure it does not create a trip or

fire/electrical hazard. Avoid places where it could become chafed.

E5

Connect the base unit

If you want to install the base unit

on the wall, see page E7.

To AC outlet

To telephone outlet

To TEL LINE

To DC IN 9V

AC adaptor

(supplied)

Telephone line cord

(supplied)

3

2

1

Snap the bottom bracket into the notches on the base.

2

Connect the AC adaptor to the

DC IN 9V

jack and to a standard 120-V AC wall outlet.

Then raise the antenna to a vertical position.

3

Connect the telephone line cord to the

TEL LINE

jack and to a telephone outlet.

Note:

Desktop use

GETTING

STARTED

To assure proper handset charging, the bottom bracket must be attached.

Note:

CLT2415 ENG-6/20 6/20/01 19:07 Page 5

E6

Choose the dialing mode

Depending on your dialing system, set the PULSE-TONE switch as follows:

If your dialing system is Set the switch to

Tone TONE

Pulse PULSE

If you are not sure of your dialing system

Make a trial call with the PULSE-TONE switch set to TONE.

If the call connects, leave the switch as is; otherwise, set to

PULSE.

PULSE

TONE

• Use only the supplied AD-350 AC adaptor. Do not use any other AC adaptor.

• Connect the AC adaptor to a continuous power supply.

• Place the base unit close to the AC outlet so that you can unplug the AC adaptor easily.

• If your telephone outlet is not modular, contact your telephone company for assistance.

Notes:

GETTING

STARTED

CLT2415 ENG-6/20 6/20/01 19:07 Page 6

E7

Standard wall plate mounting

This phone can be mounted on any standard telephone wall plate.

1

Attach the bottom bracket to the base as

shown. Make sure all tabs snap into the

notches on the base.

2

Plug the telephone line cord to the

TEL LINE

jack and the small plug of the AC

adaptor to the

DC IN 9V

jack.

3

Plug the telephone line cord into the

telephone outlet.

4

Fit the AC adaptor cord into the molded

groove. Then wrap the cord around the strain

relief notch.

5

Plug the AC adaptor into a standard

120-V AC wall outlet.

6

Raise the antenna to a vertical position.

7

Align the mounting slots on the base with the

mounting posts on the wall. Push in and

down until the phone is firmly seated.

1

2 - 7

Mounting the base unit on a wall

GETTING

STARTED

CLT2415 ENG-6/20 6/20/01 19:07 Page 7

TOP

1/8 in.

3-15/16 in.

(3 mm)

(100 mm)

E8

Direct wall-mounting

If you do not have a standard wall plate, you can still mount your phone directly to the

wall. Before doing this, consider the following:

• Avoid electrical cables, pipes, or other items behind the mounting location, that could

cause a hazard when inserting screws into the wall.

• Try to mount your phone within 10 –15 feet (3 – 4.5 m) of a working phone jack to

avoid excessive cord lengths.

• Make sure the wall material is capable of supporting the weight of the base and

handset.

• Use

#10 screws with anchoring devices suitable for the wall material where the base

unit will be placed.

1

Insert two mounting screws with a minimum length

of 1-3/8 inches (35.5 mm) into the wall, 3-15/16

inches (100 mm) apart. Allow about 1/8 of an inch

(3 mm) between the wall and screwheads for

mounting the phone.

2

Refer to steps 1 through 9 on page 7 and 8 to

mount the telephone.

8

On the base unit, pull the handset retainer out

of the slot. Rotate it clockwise 180 degrees.

9

Flip the retainer . Slide it back into the slot so

that the lip of the retainer is up and the

points down. The retainer holds the handset in

place.

Handset retainer

When the phone is mounted on

the wall, the handset belt clip

must be attached to hold the

handset in the charging position.

Do not place the handset with the

display facing inside.

Note:

GETTING

STARTED

CLT2415 ENG-6/20 6/20/01 19:07 Page 8

E9

Charge the battery pack for a full 15 hours before you start using your phone.

1

Press on the battery cover and slide the cover

down until it comes off.

2

Plug the battery pack connector with the correct

polarity (black and red wires), then insert the

battery pack into the battery compartment.

3

Slide the battery cover on until it snaps into

place.

4

Place the handset on the base.

5

Make sure that the

CHARGE/IN USE

indicator

lights. If the indicator does not light, check to

see that the AC adaptor is plugged in and that

the handset makes good contact with the base

charging contacts.

CHARGE/IN USE

Use only battery pack supplied or the specified

Sanyo types with your phone.

Type: SANYO 3KR-800AAE

Note:

Preparing the battery pack

GETTING

STARTED

CLT2415 ENG-6/20 6/20/01 19:07 Page 9

E10

Battery use time (per charge)

With a fully charged battery:

• Six hours continuous use.

• Ten days when the handset is in the standby mode.

When the battery charge level

becomes low

When the voltage of the battery pack in the handset

is very low and needs to be charged, the phone is

programmed to stop functioning in order to save power.

If the phone is not in use,

Low Battery

flashes and none of the keys will operate. If

the phone is in use,

Low Battery

flashes and the handset beeps. Complete your

conversation as quickly as possible and return the handset to the base unit for charging.

Cleaning the battery contacts

To maintain a good charge, it is important to clean the battery contacts with a dry cloth

on the handset and base unit about once a month.

Do not use any liquids or solvents.

Low Battery

GETTING

STARTED

Note:

Repeated short chargings may cause memory effect

in the battery pack, which reduces use time of the

battery. It is recommended not to replace the

handset to the base unit after each call.

CLT2415 ENG-6/20 6/20/01 19:07 Page 10

Other Operations

When you want to: Do this:

Adjust the earpiece volume Press or during the call.

Temporarily switch to tone dialing Press . The subsequent numbers

(When the base is set to pulse mode) dialed will be sent as tone dialing.

Enter a pause in the dialing sequence Press

REDIAL/PAUSE.

3

The number is dialed. The call time display

appears about 5 seconds after line connection.

4

To hang up, press

TALK/END

(or place the

handset on the base).

The call time display remains for about

5 seconds after disconnection.

E11

Dialing from standby mode

1

Enter the phone number. (Up to 32 digits.)

Example

: Enter 9057609944

2

Press

TALK/END

.

Talk

flashes in the display.

The volume setting is displayed. For example, if

the volume is set to Volume Medium, the display shows:

9057609944

Talk

9057609944

Talk

Volume Medium

Talk 0:00

9057609944

5:15

BASICS

• Press DELETE if you enter a wrong number at step 1.

• Press and hold DELETE to delete all numbers at once.

• You must press a key within 20 seconds or the phone will return to standby.

Notes:

Making a call

CLT2415 ENG-6/20 6/20/01 19:07 Page 11

E12

Dialing from talk mode

1

Press

TALK/END

.

Talk

flashes on the display.

The volume setting is displayed.

For example, if the volume is set to Volume Medium, the

display shows:

The call-time display appears.

2

Dial the phone number.

Example

: Enter 9057609944

3

To hang up, press

TALK/END

(or place the handset in the

base)

.

The call time display remains for about 5 second after

disconnection.

Talk

Volume Medium

Talk 0:17

9057609944

10:03

BASICS

CLT2415 ENG-6/20 6/20/01 19:07 Page 12

E13

1

The phone rings.

Incoming call

appears.

2

Press

TALK/END

.

Talk

, the call time display and volume

setting appear.

If you subscribe to Caller ID service, the display may show

caller’s name/number. (See E26)

3

Talk with the caller.

4

To hang up, press

TALK/END

.

The call time display remains for about

5 seconds after disconnection.

Incoming Call

Talk 0:02

Talk 0:00

Volume Medium

5:15

Any key answer when ringing

When the AutoTalk setting is on and the handset is off the base, press any handset key to

answer the incoming call.

AutoTalk when ringing

When the AutoTalk setting is on, you can simply lift the handset from the base to answer

the phone. See “Setting Caller ID options” on page E26 for more details.

Note: You must subscribe to Call Waiting service to use this feature.

When a call is received during a telephone call already in progress, you hear a beep.

Press

FLASH to switch to the new call.

If you also subscribe to Caller ID on Call Waiting (Visual Call Waiting), you will see the

name and number of the second caller. (See page E34.)

Receiving a call

Call Waiting

BASICS

CLT2415 ENG-6/20 6/20/01 19:07 Page 13

E14

Ringer volume

In the standby mode, press CALL REVIEW/

VOLUME

or on the handset to set

the handset ringer volume.

The phone has two ringer tones, each with

two volume levels.

Scanning

Lighted keypad

Adjusting the ringer and earpiece volume

BASICS

Your phone automatically selects the clearest possible channel every time you

receive or place a call. Should you wish to switch channels during a call, the handset

provides a

SELECT/SCAN button.

Keys on the handset light up when you press any key on the keypad. The light turns

off if no key is pressed within 10 seconds.

Ringer off

In the standby mode or when you set the ringer

volume, press and hold

CALL REVIEW/VOLUME

till “Ringer off” appears.

To resume the Ringer, press

CALL REVIEW/VOLUME or .

Ringer Off

Earpiece volume

Pressing CALL REVIEW/VOLUME or during

a telephone call will change the earpiece volume.

This setting will remain in effect even after you hang

up the telephone.

When you press in Volume Maximum mode or press in Volume Low mode,

a beep sounds.

Volume High

Volume Medium

Volume Maximum

Volume Low

Ringer A High

Ringer A Low

Ringer B High

Ringer B Low

CLT2415 ENG-6/20 6/20/01 19:07 Page 14

E15

The last three phone numbers dialed can be quickly redialed.

Redialing from standby mode

1

Press

REDIAL/PAUSE.

The phone number that was last dialed appears in the

display.

2

Press

REDIAL/PAUSE

again.

Each press of

REDIAL/PAUSE

will display one of the

last three numbers dialed.

3

Press

TALK/END

.

Talk

appears in the display, then

the volume setting is displayed.

4

Then the selected number is dialed. The call time

display appears 5 seconds after line connection.

5

To hang up, press

TALK/END

(or place the handset on

the base). The call time display remains for about

5 seconds.

9057609944

REDIAL/PAUSE

2145551234

9725554321

Most

recent

TALK/END

• If the dialed number exceeds 32 digits, only the first 32 digits are retained for redialing.

• If no numbers have been dialed using this phone, you hear an error beep and no redialing

will be made.

• If no key is pressed within 20 seconds, an error tone sounds and the telephone returns to

the standby mode.

Notes:

Redialing a call

BASICS

CLT2415 ENG-6/20 6/20/01 19:07 Page 15

E16

Redialing from talk mode

1

Press

TALK/END

.

Talk

appears on the display.

2

Press

REDIAL/PAUSE

.

The last number dialed will be displayed. Only the last

number dialed can be accessed while in talk mode.

3

To hang up, press

TALK/END

(or place the handset on the

base).

Talk

Volume Medium

• Only the last number dialed can be accessed after TALK/END

has been pressed.

• If no numbers have been dialed using this phone, you hear an

error beep and no redialing will be made.

Note:

BASICS

CLT2415 ENG-6/20 6/20/01 19:07 Page 16

Page is loading ...

Sanyo CLT-2415 User manual

Sanyo CLT-2415 User manual

Related papers

Other documents