CLT-2415
INSTRUCTION MANUAL
2.4-GHz
Digital Spread Spectrum
Cordless Telephone
with Call Manager Features
IMPORTANT
Charge the handset battery pack for a full 15 hours before using your
cordless handset for the first time.
www.sanyocanada.com
CLT2415 ENG-6/20 6/20/01 19:07 Page i
Congratulations on your purchase of the CLT-2415 cordless telephone.
This phone is designed for reliability, long life, and outstanding performance utilizing the
latest in 2.4 GHz Digital Spread Spectrum technology.
Note: Some illustrations in this manual may differ from the actual unit for
explanation purposes.
● 2.4 GHz Digital Spread Spectrum Technology
● Call Manager Features*: Caller ID, Caller ID on Call Waiting and Call Waiting with Options
*Each feature works with your network service. A subscription required.
● 50-Number Caller ID List
● 3-Line, 16-Character Backlit Handset Display
● Lighted Handset Keypad and TALK/END Key
● 20-Name/Number Directory
● Last 3-Number Redial
● 10-Day Standby Battery Life/6-Hour Talk Time
● Reversible Handset Charging
● 35-Channel Auto/Manual Scan
● Digital Security Code
● Call Time Display
● Pulse/Tone Dialing
● Page/Handset Locator
● Handset Earpiece/Volume Control
● Ringer Volume Control with Off Setting
● Belt Clip and Headset Jack
● Wall-Mountable
● Hearing Aid Compatible
2.4-GHz Digital Spread Spectrum Technology utilizes a “wider frequency band”
vs. a “single narrow band” used in standard digital transmissions. The result is the
clarity of digital sound, extended range and a secure conversation with virtually no
interference from other 2.4 GHz cordless phones or radio transmission devices.
The clearest channel is automatically selected for each transmission. The phone
selects one of over 65,000 digital security codes for the handset and base.
These features enhance your phone’s security and also prevent unauthorized calls
as a result of your phone being activated by other equipment.
Introduction
Features
CLT2415 ENG-6/20 6/20/01 19:09 Page ii
1. Handset antenna
2. Headset jack cover
3. Battery compartment
4. Earpiece speaker
5. LCD display
6. MEMORY key
7. TALK/END key
8. CALL REVIEW/VOLUME (down) key
9.
L
eft cursor key (TONE/
*
/)
10. REDIAL/PAUSE key
11. MENU key
12. Microphone
13. CALL REVIEW/VOLUME (up) key
14. FLASH key
15. CID key
16. Right cursor key ( )
17. DELETE key
18. SELECT/SCAN key
19. Handset charging contacts
Controls and functions
1
2
3
4
5
6
7
8
9
12
10
11
14
15
18
19
17
16
13
CLT2415 ENG-6/20 6/20/01 19:07 Page iii
21
20
22
25
23
24
26 27 28
20. Bottom bracket
21. Handset retainer
22. Base charging contacts
23. PAGE/FIND key
24. CHARGE/IN USE indicator
25. Base antenna
26. Pulse-Tone switch
27. DC power input
28. Phone jack
CLT2415 ENG-6/20 6/20/01 19:07 Page iv
E1
Introduction/Features ..............................................inside front cover
Controls and Functions............................................inside front cover
Getting started
Read this first..........................................................................................E2
Step 1: Checking the package contents .........................................E3
Step 2: Setting up the base unit ........................................................E4
Desktop use ..............................................................................E5
Mounting the base unit on a wall .......................................E7
Step 3: Preparing the battery pack ...................................................E9
Basics
Making a call ........................................................................................E11
Receiving a call....................................................................................E13
Call Waiting ..........................................................................................E13
Lighted keypad ....................................................................................E14
Scanning ...............................................................................................E14
Adjusting the ringer and earpiece volume...................................E14
Redialing a call.....................................................................................E15
Directory
Storing phone numbers and names ..............................................E17
Steps for Entering Names and Special Characters....................E19
Making calls from the directory ......................................................E21
Editing a stored name and/or phone number ............................E23
Erasing a stored name and phone number .................................E25
Caller ID features
Caller ID .................................................................................................E26
When the telephone rings................................................................E28
Viewing the Caller ID list...................................................................E29
Deleting information from the Caller ID list .................................E30
Using the Caller ID list .......................................................................E32
Using Caller ID on Call Waiting service.........................................E34
Advanced calling features
Paging ...................................................................................................E35
Call Waiting with Options.................................................................E36
Additional Information
Changing the digital security code ................................................E37
Installing the belt clip.........................................................................E38
Headset installation ...........................................................................E38
Note on power source.......................................................................E39
Maintenance ........................................................................................E39
Troubleshooting......................................................................................E40
Technical Information ...........................................................................E41
Warranty ...................................................................................................E42
Sanyo-On-Site (SOS) Information....................................................E43
Getting Started
Basics
Directory
Caller ID
Features
Advanced Calling
Features
CONTENTS
Additional
Information
CLT2415 ENG-6/20 6/20/01 19:07 Page 1
E2
This cordless telephone must be set up before use. Follow these steps:
Step 1 (page E3)
Unpack and check the telephone and accessories.
Step 2 (pages E4 to E8)
Choose the best location to set
up the base unit.
Base unit
Step 3 (pages E9 to E10)
Insert the battery pack into the handset. You
must charge the battery pack for a full 15 hours
before using the phone.
Handset
About the digital security code
This cordless telephone uses a digital security code to prevent unauthorized access to
your base unit. This security code prevents other cordless handsets from making calls
through your base unit.
A random security code will be assigned automatically between your base unit and
handset when you charge the battery pack for the first time.
If you want to reset the security code, see page E37.
GETTING
STARTED
Read this first
CLT2415 ENG-6/20 6/20/01 19:07 Page 2
E3
Make sure you have received the following items in the package.
• Base unit
• Handset
• AC adaptor
(AD-350)
• Rechargeable
battery pack
(SANYO 3KR-800AAE)
• Telephone line
cord (1)
• Bottom bracket
for desktop use
and wall-mounting
• This Owner's Manual
• Belt clip
Checking the package contents
GETTING
STARTED
CLT2415 ENG-6/20 6/20/01 19:07 Page 3
E4
Avoid places near electrical equipment such as refrigerators, computers, TVs,
microwaves or fluorescent lamps. These may cause interference or reduce the operating
range of the cordless telephone.
Do the following steps:
• Choose the best location
• Connect the base unit
• Choose the dialing mode
• The location should be close to both a phone jack and a continuous power outlet which is
not switchable.
• Be sure there is sufficient space to raise the base antenna fully to a vertical position.
• The base can be placed on a desk, tabletop or mounted on a standard wall plate.
Notes:
Setting up the base unit
GETTING
STARTED
CLT2415 ENG-6/20 6/20/01 19:07 Page 4
When connecting the power cord, make sure it does not create a trip or
fire/electrical hazard. Avoid places where it could become chafed.
E5
Connect the base unit
If you want to install the base unit
on the wall, see page E7.
To AC outlet
To telephone outlet
To TEL LINE
To DC IN 9V
AC adaptor
(supplied)
Telephone line cord
(supplied)
3
2
1
Snap the bottom bracket into the notches on the base.
2
Connect the AC adaptor to the
DC IN 9V
jack and to a standard 120-V AC wall outlet.
Then raise the antenna to a vertical position.
3
Connect the telephone line cord to the
TEL LINE
jack and to a telephone outlet.
Note:
Desktop use
GETTING
STARTED
To assure proper handset charging, the bottom bracket must be attached.
Note:
CLT2415 ENG-6/20 6/20/01 19:07 Page 5
E6
Choose the dialing mode
Depending on your dialing system, set the PULSE-TONE switch as follows:
If your dialing system is Set the switch to
Tone TONE
Pulse PULSE
If you are not sure of your dialing system
Make a trial call with the PULSE-TONE switch set to TONE.
If the call connects, leave the switch as is; otherwise, set to
PULSE.
PULSE
TONE
• Use only the supplied AD-350 AC adaptor. Do not use any other AC adaptor.
• Connect the AC adaptor to a continuous power supply.
• Place the base unit close to the AC outlet so that you can unplug the AC adaptor easily.
• If your telephone outlet is not modular, contact your telephone company for assistance.
Notes:
GETTING
STARTED
CLT2415 ENG-6/20 6/20/01 19:07 Page 6
E7
Standard wall plate mounting
This phone can be mounted on any standard telephone wall plate.
1
Attach the bottom bracket to the base as
shown. Make sure all tabs snap into the
notches on the base.
2
Plug the telephone line cord to the
TEL LINE
jack and the small plug of the AC
adaptor to the
DC IN 9V
jack.
3
Plug the telephone line cord into the
telephone outlet.
4
Fit the AC adaptor cord into the molded
groove. Then wrap the cord around the strain
relief notch.
5
Plug the AC adaptor into a standard
120-V AC wall outlet.
6
Raise the antenna to a vertical position.
7
Align the mounting slots on the base with the
mounting posts on the wall. Push in and
down until the phone is firmly seated.
1
2 - 7
Mounting the base unit on a wall
GETTING
STARTED
CLT2415 ENG-6/20 6/20/01 19:07 Page 7
TOP
1/8 in.
3-15/16 in.
(3 mm)
(100 mm)
E8
Direct wall-mounting
If you do not have a standard wall plate, you can still mount your phone directly to the
wall. Before doing this, consider the following:
• Avoid electrical cables, pipes, or other items behind the mounting location, that could
cause a hazard when inserting screws into the wall.
• Try to mount your phone within 10 –15 feet (3 – 4.5 m) of a working phone jack to
avoid excessive cord lengths.
• Make sure the wall material is capable of supporting the weight of the base and
handset.
• Use
#10 screws with anchoring devices suitable for the wall material where the base
unit will be placed.
1
Insert two mounting screws with a minimum length
of 1-3/8 inches (35.5 mm) into the wall, 3-15/16
inches (100 mm) apart. Allow about 1/8 of an inch
(3 mm) between the wall and screwheads for
mounting the phone.
2
Refer to steps 1 through 9 on page 7 and 8 to
mount the telephone.
8
On the base unit, pull the handset retainer out
of the slot. Rotate it clockwise 180 degrees.
9
Flip the retainer . Slide it back into the slot so
that the lip of the retainer is up and the
points down. The retainer holds the handset in
place.
Handset retainer
When the phone is mounted on
the wall, the handset belt clip
must be attached to hold the
handset in the charging position.
Do not place the handset with the
display facing inside.
Note:
GETTING
STARTED
CLT2415 ENG-6/20 6/20/01 19:07 Page 8
E9
Charge the battery pack for a full 15 hours before you start using your phone.
1
Press on the battery cover and slide the cover
down until it comes off.
2
Plug the battery pack connector with the correct
polarity (black and red wires), then insert the
battery pack into the battery compartment.
3
Slide the battery cover on until it snaps into
place.
4
Place the handset on the base.
5
Make sure that the
CHARGE/IN USE
indicator
lights. If the indicator does not light, check to
see that the AC adaptor is plugged in and that
the handset makes good contact with the base
charging contacts.
CHARGE/IN USE
Use only battery pack supplied or the specified
Sanyo types with your phone.
Type: SANYO 3KR-800AAE
Note:
Preparing the battery pack
GETTING
STARTED
CLT2415 ENG-6/20 6/20/01 19:07 Page 9
E10
Battery use time (per charge)
With a fully charged battery:
• Six hours continuous use.
• Ten days when the handset is in the standby mode.
When the battery charge level
becomes low
When the voltage of the battery pack in the handset
is very low and needs to be charged, the phone is
programmed to stop functioning in order to save power.
If the phone is not in use,
Low Battery
flashes and none of the keys will operate. If
the phone is in use,
Low Battery
flashes and the handset beeps. Complete your
conversation as quickly as possible and return the handset to the base unit for charging.
Cleaning the battery contacts
To maintain a good charge, it is important to clean the battery contacts with a dry cloth
on the handset and base unit about once a month.
Do not use any liquids or solvents.
Low Battery
GETTING
STARTED
Note:
Repeated short chargings may cause memory effect
in the battery pack, which reduces use time of the
battery. It is recommended not to replace the
handset to the base unit after each call.
CLT2415 ENG-6/20 6/20/01 19:07 Page 10
Other Operations
When you want to: Do this:
Adjust the earpiece volume Press or during the call.
Temporarily switch to tone dialing Press . The subsequent numbers
(When the base is set to pulse mode) dialed will be sent as tone dialing.
Enter a pause in the dialing sequence Press
REDIAL/PAUSE.
3
The number is dialed. The call time display
appears about 5 seconds after line connection.
4
To hang up, press
TALK/END
(or place the
handset on the base).
The call time display remains for about
5 seconds after disconnection.
E11
Dialing from standby mode
1
Enter the phone number. (Up to 32 digits.)
Example
: Enter 9057609944
2
Press
TALK/END
.
Talk
flashes in the display.
The volume setting is displayed. For example, if
the volume is set to Volume Medium, the display shows:
9057609944
Talk
9057609944
Talk
Volume Medium
Talk 0:00
9057609944
5:15
BASICS
• Press DELETE if you enter a wrong number at step 1.
• Press and hold DELETE to delete all numbers at once.
• You must press a key within 20 seconds or the phone will return to standby.
Notes:
Making a call
CLT2415 ENG-6/20 6/20/01 19:07 Page 11
E12
Dialing from talk mode
1
Press
TALK/END
.
Talk
flashes on the display.
The volume setting is displayed.
For example, if the volume is set to Volume Medium, the
display shows:
The call-time display appears.
2
Dial the phone number.
Example
: Enter 9057609944
3
To hang up, press
TALK/END
(or place the handset in the
base)
.
The call time display remains for about 5 second after
disconnection.
Talk
Talk
Volume Medium
Talk 0:17
9057609944
10:03
BASICS
CLT2415 ENG-6/20 6/20/01 19:07 Page 12
E13
1
The phone rings.
Incoming call
appears.
2
Press
TALK/END
.
Talk
, the call time display and volume
setting appear.
If you subscribe to Caller ID service, the display may show
caller’s name/number. (See E26)
3
Talk with the caller.
4
To hang up, press
TALK/END
.
The call time display remains for about
5 seconds after disconnection.
Incoming Call
Talk 0:02
Talk 0:00
Volume Medium
5:15
Any key answer when ringing
When the AutoTalk setting is on and the handset is off the base, press any handset key to
answer the incoming call.
AutoTalk when ringing
When the AutoTalk setting is on, you can simply lift the handset from the base to answer
the phone. See “Setting Caller ID options” on page E26 for more details.
Note: You must subscribe to Call Waiting service to use this feature.
When a call is received during a telephone call already in progress, you hear a beep.
Press
FLASH to switch to the new call.
If you also subscribe to Caller ID on Call Waiting (Visual Call Waiting), you will see the
name and number of the second caller. (See page E34.)
Receiving a call
Call Waiting
BASICS
CLT2415 ENG-6/20 6/20/01 19:07 Page 13
E14
Ringer volume
In the standby mode, press CALL REVIEW/
VOLUME
or on the handset to set
the handset ringer volume.
The phone has two ringer tones, each with
two volume levels.
Scanning
Lighted keypad
Adjusting the ringer and earpiece volume
BASICS
Your phone automatically selects the clearest possible channel every time you
receive or place a call. Should you wish to switch channels during a call, the handset
provides a
SELECT/SCAN button.
Keys on the handset light up when you press any key on the keypad. The light turns
off if no key is pressed within 10 seconds.
Ringer off
In the standby mode or when you set the ringer
volume, press and hold
CALL REVIEW/VOLUME
till “Ringer off” appears.
To resume the Ringer, press
CALL REVIEW/VOLUME or .
Ringer Off
Earpiece volume
Pressing CALL REVIEW/VOLUME or during
a telephone call will change the earpiece volume.
This setting will remain in effect even after you hang
up the telephone.
When you press in Volume Maximum mode or press in Volume Low mode,
a beep sounds.
Volume High
Volume Medium
Volume Maximum
Volume Low
Ringer A High
Ringer A Low
Ringer B High
Ringer B Low
CLT2415 ENG-6/20 6/20/01 19:07 Page 14
E15
The last three phone numbers dialed can be quickly redialed.
Redialing from standby mode
1
Press
REDIAL/PAUSE.
The phone number that was last dialed appears in the
display.
2
Press
REDIAL/PAUSE
again.
Each press of
REDIAL/PAUSE
will display one of the
last three numbers dialed.
3
Press
TALK/END
.
Talk
appears in the display, then
the volume setting is displayed.
4
Then the selected number is dialed. The call time
display appears 5 seconds after line connection.
5
To hang up, press
TALK/END
(or place the handset on
the base). The call time display remains for about
5 seconds.
<Redial1>
9057609944
REDIAL/PAUSE
REDIAL/PAUSE
REDIAL/PAUSE
<Redial2>
2145551234
<Redial3>
9725554321
Most
recent
TALK/END
• If the dialed number exceeds 32 digits, only the first 32 digits are retained for redialing.
• If no numbers have been dialed using this phone, you hear an error beep and no redialing
will be made.
• If no key is pressed within 20 seconds, an error tone sounds and the telephone returns to
the standby mode.
Notes:
Redialing a call
BASICS
CLT2415 ENG-6/20 6/20/01 19:07 Page 15
E16
Redialing from talk mode
1
Press
TALK/END
.
Talk
appears on the display.
2
Press
REDIAL/PAUSE
.
The last number dialed will be displayed. Only the last
number dialed can be accessed while in talk mode.
3
To hang up, press
TALK/END
(or place the handset on the
base).
Talk
Talk
Volume Medium
• Only the last number dialed can be accessed after TALK/END
has been pressed.
• If no numbers have been dialed using this phone, you hear an
error beep and no redialing will be made.
Note:
BASICS
CLT2415 ENG-6/20 6/20/01 19:07 Page 16
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
