Cannondale Scalpel 29 Owner's manual

Cannondale
Brand
Cannondale
Model
Scalpel 29
Category
Signal cables
Type
Owner's manual

Cannondale Scalpel 29 is a high-performance mountain bike designed for tackling challenging trails with speed and efficiency. Its lightweight carbon frame and advanced suspension system provide exceptional handling and control, allowing riders to navigate rough terrain with confidence. The 29-inch wheels offer increased stability and roll over obstacles with ease, while the wide range of gears ensures optimal cadence on both steep climbs and fast descents.

Cannondale Scalpel 29 is a high-performance mountain bike designed for tackling challenging trails with speed and efficiency. Its lightweight carbon frame and advanced suspension system provide exceptional handling and control, allowing riders to navigate rough terrain with confidence. The 29-inch wheels offer increased stability and roll over obstacles with ease, while the wide range of gears ensures optimal cadence on both steep climbs and fast descents.

Page 1 of 4
128981 - 03/12
Page 1 of 1
TECH NOTE
03/12
Scalpel 29’ER Carbon BB Routing
Bottom Bracket Routing Loop
The 1” (2,5cm) cable loop under the BB shell is needed for
cable clearance with the frame. If the loop is too short,
or if the cables slide through the clamps because the are
loose, the cables can contact frame. This can happen,
particularly with the FD cable at the back of the shell as
the suspension is fully compressed.
To prevent frame damage caused by cable rub,
periodically check the BB routing. Do the following:
1. Check the cable clamps. If they are loose, rather
than simply re-tightening, it is a good idea to remove
the cable guide bolts, clean the threads and apply
Loctite 242 (blue) and tighten each to
3.0 Nm (26.5 InLbs).
2. Check the BB loop. It should be about 1” measured
in the area shown above. Loosen the clamp bolts and
adjust the size of the loop. If the loop is too short you
will have to use a longer FD cable. If it is too long, you
may be able to shorten it.
3. The RD cable has less chance to rub the underside of the
shell. It should follow the loop of the FD and be secured
to the chain stay with a new cable tie.
Additionally the two cables may be crossed under the
shell. This can minimize cable movement and limit the
chance of the loop changing if the cables slip in the
clamps.
As an added protection, place small sections of readily
available adhesive frame guard material between the
cable and BB shell. Cannondale kit KF103/ includes
eight 25 x 35 mm pieces suitable for various locations
on the frame.
Please Note: Damage caused to your bike by cable rubbing
is not covered by your Cannondale Limited Warranty. So,
you’ll want to include a check of the routing in the BB area
as part of your regular maintenance routines.
If you have any questions about this Tech Note, please
contact Cannondale Dealer Service at 1-800-THE-BIKE
(1-800-843-2453).
Loctite 242 (blue)
3 Nm, (26.5 InLbs)
FRONT
DERAILLEUR
CABLE
REAR
DERAILLEUR
CABLE
CABLE CLAMP - KP210/
CHAIN STAY
CABLE TIE - KP183/
1” (2,5cm)
BB CABLE LOOP
SCUFFGUARD - KF103/
  • Page 1 1

Cannondale Scalpel 29 Owner's manual

Cannondale
Brand
Cannondale
Model
Scalpel 29
Category
Signal cables
Type
Owner's manual

Cannondale Scalpel 29 is a high-performance mountain bike designed for tackling challenging trails with speed and efficiency. Its lightweight carbon frame and advanced suspension system provide exceptional handling and control, allowing riders to navigate rough terrain with confidence. The 29-inch wheels offer increased stability and roll over obstacles with ease, while the wide range of gears ensures optimal cadence on both steep climbs and fast descents.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents